This patch enables support for USB 2.0 in AP-MI01.2
Change-Id: I4f848a403f3aae45a9f1cfa136781fbc7a37c35a
Signed-off-by: Timple Raj M <quic_timple@quicinc.com>
The pcie AUX clock source changed to XO as per
GCC frequency plan
Change-Id: If032831d3a9523ec214a62cbed2950ee5839920e
Signed-off-by: Timple Raj M <quic_timple@quicinc.com>
added boot type based nand or emmc flash selection.
So machid based flash selection becomes obsolete.
Change-Id: I96fa43d31d23397fa249e02f62b905d6e4e67770
Signed-off-by: Rajkumar Ayyasamy <quic_arajkuma@quicinc.com>
Bootconfig partition can have the MAGIC value 0xA3A3A1A1
if try_mode is enabled. Update the checks in smem APIs
Change-Id: I2fb71ff5812468f3f5ecd0153c35cab7d8e4bb44
Signed-off-by: Gurumoorthy Santhakumar <quic_gsanthak@quicinc.com>
Only one SFP port can be enabled at time with
either SGMII or SGMII PLUS mode.
Mode shall be specified from dts for 1G or 2.5G
support respectively. Add below change to enable
SFP as this change is not mainlined.
gmac_cfg {
gmac2_cfg {
unit = <1>;
base = <0x39D00000>;
- phy_address = <0x1c>;
- napa_gpio = <39>;
/*
* 6 - SGMII_PLUS (2.5G),
* 8 - SGMII_FIBER (1G)
*/
+ switch_mac_mode = <8>;
+ sfp_tx_gpio = <27>;
+ sfp_rx_gpio = <29>;
};
};
Change-Id: I507be2b84b1f932802659abffa3288e304e0d411
Signed-off-by: Gokul Sriram Palanisamy <quic_gokulsri@quicinc.com>
This patch removes the support for dumpinfo_s structure to have
uniform EBICS0 bin for both sec and non-sec boots as the Read As Zero
(RAZ) flag has been enabled to protect code and data regions of TZ
The patchset applies to all the targets except IPQ5018 as the RAZ
flag enablement was not supported in IPQ5018
Change-Id: I63514284448de08926cd2c9b741f02859067044d
Signed-off-by: devi priya <quic_devipriy@quicinc.com>
Add support for ECO bit toggle during IPC start/stop
messages to allow BT subsystem to do self reset
Change-Id: I4d1d31a43ea8a002eb91cc42300677339c117d71
Signed-off-by: Rajkumar Ayyasamy <quic_arajkuma@quicinc.com>
This change adds cmd_dpr as a common file,
so it will be reused in the future SoC.
dpr support added in Devsoc SoC.
Change-Id: I246a8f51c07c2f6952173bbd72e327ab1119af6e
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
Adding a new command mibib_reload to
populate the partition table info from
mibib binary
Change-Id: I3f08fc07ea55f1bbd90dc28d8f459d108f86bc0e
Signed-off-by: Timple Raj M <quic_timple@quicinc.com>
This patch eliminates to maintain seperate dts file
for mmc flash. It enables flash node based
on machine id.
Change-Id: I67d95db162630a3bc84429e8a9338097e1e24619
Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com>
This RDP is based on AL03-C1.
The extra feature are WK03.2 – 2G+5GL in Pcie 0 &
WK01.7 – 5GH+6G in Pcie 2.
Change-Id: Ic52c71e98e1a06acf36a825d23f1d184601d153a
Signed-off-by: Saahil Tomar <quic_saahtoma@quicinc.com>
This RDP is based on AL02-C6.
The extra feature is W5GL-4 in Pcie 1.
In U-boot, RDP is based on AL02-C4 as Interface enablement
is same as AL02-C12.
Change-Id: If81b5950d02b47c021aea3d52fdf5feb3fcb7035
Signed-off-by: Saahil Tomar <quic_saahtoma@quicinc.com>
This is RDP is based on AL02-C4. The extra feature is Alder 2G.
Change-Id: I175938c886c0ebd8f39659ba28be2a946d5b7494
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
The PCIE node is disabled by default in
the emulation platform
Change-Id: I51041186a57d08b58c1f7c85dd1a90fbeb24aac9
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
This change adds support to enable multiple I2C bus on all IPQ
platforms. Removed the device specific changes and updated in
a generic way to support multiple I2C on all the IPQ platforms.
Change-Id: Ie13dd744c6317fc9245bc88781e79a9fb3621a62
Signed-off-by: Ram Kumar D <quic_ramd@quicinc.com>
AL02-C9 is similar to AL02-C6 without internal radio
Features: Split Phy WKK (2G + 5G), Split Phy WKK (5G + 6G)
Change-Id: I637123bc133243f20dfc0fddb7353caad8650c3a
Signed-off-by: Timple Raj M <quic_timple@quicinc.com>
This changes add support for uboot base files.
Change-Id: I5f4b937dec30a27ec6acce6ceada7fbed5d5a41d
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
AL02-C8 is based on AL02-C4. Instead of QCA8075, QCA8084 is used
for Ethernet.
Change-Id: I70e3560461c1a547c40f5b9b839cc94ef2a39520
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
Setting this bit will not allow PPE to take any action on the
packets. Remove this configuration as its not needed in U-Boot
EDMA.
Change-Id: I45cb93a4f5072dd882179eca5a14bc4a25624f26
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
AP.AL02-C7 is similar to AP.AL02-C4 with emmc boot
Features: WK 2G + WK5G + WK 6G
AP.AL02-C8 is similar to AP.AL02-C6 with emmc boot
Features: Internal 2G +WK 5G + WK 6G
Change-Id: I31d1f65b071dfddc4eee393d292add58d3ddeadc
Signed-off-by: Timple Raj M <quic_timple@quicinc.com>
Currently, if atf env is set in the secure board. secure boot
sequence gets bypassed. This is not an expected behaviour. So,
removed support the atf env variable. Instead atf enabled status
can be verified using get_secure_state scm call.
Moreover, as per current design get_secure_state scm call will
not be implemented in ATF in future as well. If its implemented,
Bit 7 should be made to 1.
Change-Id: I0adcfac7bbcb10fe6906fd8a3f10a440ec7080ae
Signed-off-by: Ram Kumar D <quic_ramd@quicinc.com>
This patch updates the following:
1) Initializes I2C QUP clocks in U-Boot itself as required
without depending on SBL.
2) Removes all CONFIG_IPQ9574_RUMI references.
Change-Id: I1fb02861a70bd2b024122fff7810c3373cc2e1cd
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
The features are similar to MP03.1 RDP.
The only difference is PINE in lane 2 is replaced by WKK.
Change-Id: Ifa83c640307081e2511ab5d8728871a8344207c4
Signed-off-by: Timple Raj M <quic_timple@quicinc.com>
This change will read the 0:ART partition for calibration data and
apply it to the appropriate registers.
Following sequence added for the same.
1. created scm_read call to read the protected register.
2. added function to read data from ART partition of all flash types
3. added function to apply data to the Caldata register.
Change-Id: I4c769be3cdf664e4c59159851cc211fca53c0f27
Signed-off-by: Ignatius Michael (Jihan) Jihan <quic_mignatiu@quicinc.com>
