This changes updates the gcc common clk initialise
steps and adds support for obtaining bitmap
details from dts.
Change-Id: I55e895989823a4fbb97c638ad937ca48c00519c5
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
This change set SGMII mode and force mode based on
dts entries.
Change-Id: Ideaa1bb77fe8fb37a7e6b907a987f6dcac54917f
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
This changes enable both PHY and switch configure
simultaneously and also switch can be configure
to any port.
And also these changes enable dual MDIO bus support.
Change-Id: Ib86c8a15abb9a7a35aa86d87cef78ad917dd1a00
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
Add skip_pci_mask environment variable to skip pci enumeration
based on the bitmask. Also, removing the pci3 dts entry from
the RDP437 & RDP461 to skip pci3 enumeration.
Example - setenv skip_pci_mask 0xc
The above command will skip pci enumeration of bus 2 & 3.
Change-Id: Iff50acca07ffc026bed84a0d2372e6de0a3ba3a9
Signed-off-by: Amandeep Singh <quic_amansing@quicinc.com>
Signed-off-by: Ram Kumar D <quic_ramd@quicinc.com>
Added JTAG ID, Serial number and Part type read.
Change-Id: Ia03724116230a157fc33406a97c641e3b5750d6a
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
It has the capacity of 1Gbit, i.e., 128MB, so
the number of blocks has been updated to 1024.
1Gbits = 128MB = 2048(page) * 64 (pages per block) * 1024 (blocks)
Change-Id: I552776e4e151d16782db915c3ebae874c5c02696
Signed-off-by: Gurumoorthy Santhakumar <quic_gsanthak@quicinc.com>
Added new config called CONFIG_QCA8084_BYPASS_MODE and moved
all the qca8084 by-pass mode related code under it.
Change-Id: I4157960989cd67576803d494594869265fc81745
Signed-off-by: Ram Kumar D <quic_ramd@quicinc.com>
Added QCA8084 by-pass mode support on MI01.1 RDP
Change-Id: I1a14729cac5463675f9cb0d15df3da76746aa81e
Signed-off-by: Ram Kumar D <quic_ramd@quicinc.com>
These changes update config as like below.
1.Config 100M, 1G as GMAC, 2.5G as XGMAC
2.Config MHT as XGMAC.
Change-Id: I0566f3a3d364931e8c8173c3604160f24c2439be
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
Added QCN92xx's SoC global reset and MHI reset in the fuse blow path.
So, the fuse blow can be retried after any failed attempts.
Added ANTI ROLLBACK fuse read.
Change-Id: Ibf255390ffc2086fcbfa9041dc0bcb612f8d9a4e
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
This changes includes update the Speed clock,
common clock update and dts nodes.
Change-Id: I673e8ccf191048fef966a8f6cd84858e1a3b824f
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
Only one SFP port can be enabled at time with
either SGMII or SGMII PLUS mode.
Mode shall be specified from dts for 1G or 2.5G
support respectively. Add below change to enable
SFP as this change is not mainlined.
gmac_cfg {
gmac2_cfg {
unit = <1>;
base = <0x39D00000>;
- phy_address = <0x1c>;
- napa_gpio = <39>;
/*
* 6 - SGMII_PLUS (2.5G),
* 8 - SGMII_FIBER (1G)
*/
+ switch_mac_mode = <8>;
+ sfp_tx_gpio = <27>;
+ sfp_rx_gpio = <29>;
};
};
Change-Id: I507be2b84b1f932802659abffa3288e304e0d411
Signed-off-by: Gokul Sriram Palanisamy <quic_gokulsri@quicinc.com>
"list_qcn9224_fuse" command will print the OEM ID, Secure boot enable
and OEM PK hash details of QCN9224 from all attached PCIe slots.
Change-Id: I87be2f58bcef6898a00f4e179c87f2dcb93a2604
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
This change will add support for giga device GD5F1GM7REYIG
spi nand support.
Change-Id: Ie32cb6824bd0fbcf04449fa070005b7fa323c025
Signed-off-by: Timple Raj M <quic_timple@quicinc.com>
This change adds usxgmii support in UNIPHY0.
Earlier it was supported up to PSGMII with 4 ports.
With these changes,
UNIPHY0 supports either of the 2 modes mentioned below.
1. PSGMII with 4 ports
2. USXGMII with 1 port
Change-Id: Ic4ca62e3ef74d275cda92d86b459d204ee4325ed
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
This change adds a new command to support the qcn9224 fusing.
Fuser blower binary should be transfered via tftp to Host and
using fuse_qcn9224 command, binary can be transfered to qcn9224.
qcn9224 will take care of the fusing.
sample command:
tftpboot fuse_blower.bin
fuse_qcn9224 0
Change-Id: Ie8cd73a2d49799100bd1f717cdc4b8dad070f9bd
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
