This change adds usxgmii support in UNIPHY0.
Earlier it was supported up to PSGMII with 4 ports.
With these changes,
UNIPHY0 supports either of the 2 modes mentioned below.
1. PSGMII with 4 ports
2. USXGMII with 1 port
Change-Id: Ic4ca62e3ef74d275cda92d86b459d204ee4325ed
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
During long run tests on image download in u-boot,
EDMA crash was observed as the SKB buffer address
returned by the RX descriptor was corrupted and was
pointing to an invalid address:
clean_rx: p: 14 c: 0 skb: 61763b10
WARN: src_info_type:0x0. Drop skb:61763b10
The reason for corruption seems to be the RX buffer allocation that was
happening twice before initiating the EDMA for the next transaction.
This change removes the additional allocation of the Rx buffer which is
not needed.
Change-Id: I919024df8131fe87640ecc0d481b61012742efbf
Signed-off-by: devi priya <quic_devipriy@quicinc.com>
Currently if CONFIG_QCA8084_PHY is enabled means, it will build
all qca8084 functions required for both PHY & switch mode. But,
some ipq devices might uses anyone of them. So, add configs to
seperate the PHY & switch mode and define it in corresponding
defconfig file as per the need.
Also, some of the qca8084 functions will be used only for debug
purpose, those functions are moved under the config QCA8084_DEBUG.
Thereby, we can save some space in the u-boot.
Change-Id: I7e5f53869629a0c7cbbb12daf04ed782c9693623
Signed-off-by: Ram Kumar D <quic_ramd@quicinc.com>
In qca8084 phy mode, each phy is assigned to one mac in the ipq9574,
where as in the switch mode, only mac1 will used for all the 4 ports
of the qca8084, mac2-4 will be left unused. So, updated the
logic to update the link status of the individual ports, when qca8084
is in switch mode.
Change-Id: I128c3eafb7c85c0db9d252e047457ea8820df368
Signed-off-by: Ram Kumar D <quic_ramd@quicinc.com>
This patch adds support for qca8084 PHY based
ports. Accordingly, updates the uniphy, ppe, clock
configurations as required for qca8084 ports.
Change-Id: I2e687c10adba579b0d47d8f5b529fe920b7d0d7c
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This patch adds support for active_port env. With this
change in ipq9574, the end user has an option to
enable & maintain only 1 active ethernet port. There
are no multi-port use case in U-Boot and when multiple
ports were enabled for Kernel usecases, there were some
timeout issues in some special cases during crashdump
collection.
active_port can be used to configure the port which
will be used for TFTP download/upload in u-boot in
those setups. Example: To set Port2 as active_port
following command can be used:
setenv active_port 2 && savee
Note that, the active_port range is from 0 to 5 (there
are a total of 6 ports in ipq9574).
Change-Id: Ia2fc58abda7640f67afadfa01d0a5994aa48ea51
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
The ring/desc's used non-cached memory which cannot
be free'd. Remove these free API's.
1 MB of memory is marked as non-cached and that is used
for EDMA rings/desc's and the same needn't be free'd. It
will be re-init each time during edma init.
Change-Id: Iac1e616db7c929d640c559024e4f65c6ad515400
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This patch moves the qca8075 phy inits inside the
config. Without this patch, when we disable the
QCA8075 config, then there will be compilation
errors.
Change-Id: Ibed0517c52f896f2af54773aa31260068e116479
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This changes initialize non-cache buffer every time
before edma configuration.
Change-Id: If7692f9671f6b63f19ae38326bd76320c54766cc
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
This patch is a temporary WAR to fix timeout issues
observed in particular setups during dump collection.
This patch disables FDB Learning for ports 1-6.
Change-Id: I7987bb0286df129c56a07f1708600f78ebf42039
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
Setting this bit will not allow PPE to take any action on the
packets. Remove this configuration as its not needed in U-Boot
EDMA.
Change-Id: I45cb93a4f5072dd882179eca5a14bc4a25624f26
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This patch adds DA MAC rule. This rule can be used
if we want to drop packets with a particular DA MAC
address.
Change-Id: I32ef53ada1518f6880faa7402ccaaedb5b32a90b
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This patch adds ACL to drop the packets with src
mac address.
Change-Id: Ib944154ffb53b9bf67a178a5ab08cd9f12866b4a
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This patch optimizes and updates the EDMA Driver as
required for ipq9574 platform similar to the Kernel
Host EDMA Driver.
-> Config TX_MOD and RX_MOD timers
-> Config DMAR_CTRL
-> Config Service code bypass for TX_DESC
-> Update the SRCINFO and DST_PORT configs
-> Make changes to include secondary and primary DESC's
into the same corresponding ring structure
-> Increase the TX_BUFF Size to 2048
-> Update to use RX_DESC RING 23
-> Remove unused fields from the EDMA structures
-> Update the description for the EDMA structure fields
Change-Id: I3f7f1c11cdd87687c38774a4930c9bee90857203
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This patch updates the following:
1) Updates NSS NOC clock frequencies to expected clock rates
2) Add Debug prints during eth_halt which can help debug issues
3) Update ACL structure and configurations for ipq9574 platform
as required
4) Disable the MIB counters reset bit so that those counter
registers values can be dumped to check stats
5) Update VSI configurations for cases when BRIDGED_MODE config
is disabled
6) Update the VSI configuration to avoid flooding from one LAN
port to another
Change-Id: I39f20a57c08205fbeb669c93b6459cf8e184098d
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This patch adds support for SFP 1G and 2.5G. Note that
there is no autoneg support for SFP in U-Boot and the mode needs
to be changed in DT to make it work in 1G or 2.5G.
By default SFP will be configured to work in 10G mode.
Change-Id: I1c209276fe2a586332be87ce5d49a140f4814eb2
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
This patch adds the phy type and phy address also as part
of the print message during error cases which will help in
quickly identifying the port configuration.
Change-Id: I6762998e8bae8be8473d32e41b81ecc7e0b94885
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Uniphy clk init and deinit creates additional delay in UBoot.
Falling back to Uniphy clk init during boot up and not doing
de-init during speed changes.
Change-Id: I10fb86e4b616f46c2a0c3066308e7c6a6325cf44
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
This patch updates the following:
1) Removes unnecessary TIMER and THRESHOLD configurations in EDMA
2) Adds Uniphy Clock deinit and init in eth_init (during each ping
& speed change)
3) Removes preheader configurations and calculations from EDMA
as there are no preheaders in ipq9574 platform (Instead there is
a secondary descriptor)
4) Add sufficient delay after uniphy reset
5) Remove CONFIG_IPQ9574_RUMI macro from network drivers
6) Change default mac_speed to 0
7) Fix the ppe sched. and tdm configuration
8) Reduce the block size to 1280 + headers for tftp (around 1326)
for timebeing without which timeouts were observed randomly during
TFTP (Note that the MTU is 1514 bytes)
Change-Id: I4004adfb2ae0dc98d65e458c15dafcff6523744b
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Previous platforms assume qca8075 phy address starts from
0. This patch adds a separate qca8075 phy driver for ipq9574
platform and handles cases where qca8075 phy addr doesn't
start with 0.
Change-Id: I59a596d692b1663af638af358335056661bdf199
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
This patch does the following:
1) Removes unused macros and functions
2) Updates EDMA Reset address and assert/de-assert values
3) Updates Port5 and Port6 address in uniphy clock config
4) Reduces delay to 500 us in usxgmii uniphy mode set
5) Disable clearing of mac counters
Change-Id: I7cc9b20bbd4f2367d9f405ae2e5652d6236476a9
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
This patch does the following:
1) Adds support for AQR113C_B0 and AQR113C_B1 AQ PHY versions
which will be used in ipq9574 platform
2) Adds delay of 100 ms after FW download before calling phy
init which is necessary in ipq9574 platform without which the
init doesn't happen properly as expected
Change-Id: I50be933e68598ada5e3d9df71c3e3abcc79c52d2
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
This patch updates the macro used for modes and also additionally
increases the delay between uniphy reset as needed for ipq9574
platform
Change-Id: Ide565e071963e17abd4f8f7e5d6270849d729b21
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
This patch updates the following:
1) Updates per port port mac reset
2) Updates XGMAC based on port instead of based on Uniphy as needed
for ipq9574 platform
3) uniphy_port5_clock_source_set -> If uniphy1 is not used, then
it is assumed that the first uniphy supports 5 Malibu and so accordingly
clock source is set by calling this function in that scenario
Change-Id: I978043cfa277fa02dadee5070b94f7a77ed81a5f
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
This patch does the following:
1) Enables AQ Driver Compilation.
2) Updates malloc size to fixed value of 512 KB (size of ETHPHYFW Partition)
which is actually 1024 KB as per QSPI Nand Flash partition (considering the
bad block size also). While reading bad blocks will be skipped, and the
firmware size is not expected to exceed 512 KB and hence this size is updated.
Also note, the heap size is currently 1 MB and so if we try do malloc for 1 MB,
we might get failures during allocation.
3) Adds QSPI NAND Flash Support.
Change-Id: I5a6e19b1462b648523ce6b311128a447e34241b4
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
This patch updates the following:
1) Removes unused/duplicate macro: NSS_CC_PORT1_RX_CBCR_ADDR
2) Remove CMN_BLK_INIT
3) Update MAX Ports to 6
4) Rename switch_mac_mode to switch_mac_mode0 in DTS and driver
5) Fix SYSNOC frequency configuration
6) Tx/Rx descs is initialized to 0 before use which is
needed because Alder DDR is not init to 0 by default.
Change-Id: Ide22e146f9c8ecb75585d0a8d04e426c463ad8c9
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
This patch updates the following:
1) Update speed clock, port mac clock reset for ipq9574
platform.
2) Handle PPE init for all 3 switch mac modes.
3) Handle port mux config when port5 is part of Uniphy0
during when Uniphy1 won't be used.
Change-Id: I23b04b00036ab139cd5877bcf913dbecb7fb7fa2
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
This patch updates the following:
1) Add support for 3 switch_mac_modes in ipq9574 platform.
2) Update xpcs and soft_reset as needed for ipq9574 platform.
3) Support usecase where 5*1G ports can be supported as part
of Uniphy0 during when Uniphy1 won't be used.
Change-Id: I949db117fa3c8adb937c5c055eedcaa6ead0da07
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
This patch updates the following:
1) Handle 2 aquantia ports during ping
2) Remove SFP Port Support Temporarily
3) Update clocks for different port speeds and different
ethernet port types as needed.
4) Update number of ports to 7 since 7 is the MAX ports
supported in ipq9574 platform.
Change-Id: I2d9040227b9c8a11cddc0d00e835ac64d3a4940d
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
This patch updates the VSI settings. The VSI Table size has
now changes from 3 word to 4 word and the same has been
accomodated. Without writing 4 words to that Table, the VSI
writes won't be processed by the H/W.
This patch updates the scheduling, TDM configuration
and the ppe port mux configuration as required for ipq95xx.
This patch also moves the configurations not required
for EMU Platform to !CONFIG_IPQ9574_RUMI.
Change-Id: Id54e40d26e80c36e7a61642d8494c30bbd3ea2a5
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
This patch updates the address of the EDMA registers, removes
registers which are not used and then does the required changes
to accomodate the new EDMA Descriptor format.
This patch also does the required changes to accomodate Secondary
Descriptor which is added instead of preheaders in ipq95xx.
We have also updated the number of descriptors per ring to 128
with this patch and have also moved the configs not required for
EMU Platform to !CONFIG_IPQ9574_RUMI.
Change-Id: I6e98c457d76c66f87b74cc0eafa7088d0081f533
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
