This patch adds support for new board variant AL02-C19.
This board variant consists of one internal radio,
Waikiki 5G in pci slot 0, Waikiki 6G in pci slot 2 and
SDX in pci slot 3.
Change-Id: I43e3b5890f6bd8f6d182e4c3acc540a89f9c4a34
Signed-off-by: Nitheesh Sekar <quic_nsekar@quicinc.com>
This changes includes update the Speed clock,
common clock update and dts nodes.
Change-Id: I673e8ccf191048fef966a8f6cd84858e1a3b824f
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
Only one SFP port can be enabled at time with
either SGMII or SGMII PLUS mode.
Mode shall be specified from dts for 1G or 2.5G
support respectively. Add below change to enable
SFP as this change is not mainlined.
gmac_cfg {
gmac2_cfg {
unit = <1>;
base = <0x39D00000>;
- phy_address = <0x1c>;
- napa_gpio = <39>;
/*
* 6 - SGMII_PLUS (2.5G),
* 8 - SGMII_FIBER (1G)
*/
+ switch_mac_mode = <8>;
+ sfp_tx_gpio = <27>;
+ sfp_rx_gpio = <29>;
};
};
Change-Id: I507be2b84b1f932802659abffa3288e304e0d411
Signed-off-by: Gokul Sriram Palanisamy <quic_gokulsri@quicinc.com>
This patch removes the support for dumpinfo_s structure to have
uniform EBICS0 bin for both sec and non-sec boots as the Read As Zero
(RAZ) flag has been enabled to protect code and data regions of TZ
The patchset applies to all the targets except IPQ5018 as the RAZ
flag enablement was not supported in IPQ5018
Change-Id: I63514284448de08926cd2c9b741f02859067044d
Signed-off-by: devi priya <quic_devipriy@quicinc.com>
"list_qcn9224_fuse" command will print the OEM ID, Secure boot enable
and OEM PK hash details of QCN9224 from all attached PCIe slots.
Change-Id: I87be2f58bcef6898a00f4e179c87f2dcb93a2604
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
The CRASHDUMP RESET bit of TCSR_BOOT_MISC_DETECT Register
has to be set before reset from u-boot in the
crashdump collection path for TZ to differentiate between the
normal reset and crashdump reset from u-boot and
to retain the crash reason.
Change-Id: Ib623bfeab15d1bc230f4a8824218f1a3c4368fbb
Signed-off-by: Gurumoorthy Santhakumar <quic_gsanthak@quicinc.com>
Add support for ECO bit toggle during IPC start/stop
messages to allow BT subsystem to do self reset
Change-Id: I4d1d31a43ea8a002eb91cc42300677339c117d71
Signed-off-by: Rajkumar Ayyasamy <quic_arajkuma@quicinc.com>
Add build support for DB-MI01.1 and DB-MI02.1
Change-Id: I00a2698924813e52d196469630e271b0c3009aec
Signed-off-by: Timple Raj M <quic_timple@quicinc.com>
GPIO_PULL details updated on AP-MI01.1, AP-MI01.2, AP-MI01.4,
DB-MI01.1 and DB-MI02.1
SPI NOR added only in MI01.1 and removed from other RDP's
Renamed DB-MI01.2 to DB-MI01.1
Change-Id: Ic2c3467aa06d04dd5e759767a806b4905b0d118a
Signed-off-by: Timple Raj M <quic_timple@quicinc.com>
TCSR_BOOT_MISC_REG bits are not properly managed
for DLOAD implementation. Modify only necessary
bits to enable availability for new feature
implementations using TCSR_BOOT_MISC_REG.
Change-Id: I888a1bf6ce3654b0453c9ec2f87b4d5ff2a20de0
Signed-off-by: Gokul Sriram Palanisamy <quic_gokulsri@quicinc.com>
This changes remove pci phy deinit sequence and
also update the pci phy address
Change-Id: I9bae09958e395dfb509a17e472674f33fe214f1c
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
This change will add support for giga device GD5F1GM7REYIG
spi nand support.
Change-Id: Ie32cb6824bd0fbcf04449fa070005b7fa323c025
Signed-off-by: Timple Raj M <quic_timple@quicinc.com>
This change adds usxgmii support in UNIPHY0.
Earlier it was supported up to PSGMII with 4 ports.
With these changes,
UNIPHY0 supports either of the 2 modes mentioned below.
1. PSGMII with 4 ports
2. USXGMII with 1 port
Change-Id: Ic4ca62e3ef74d275cda92d86b459d204ee4325ed
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
Same as AP.AL02-C4 RDP, with support for 10G PHY or 10G fiber in UNIPHY0
Change-Id: Ic3935a2cdc0033ed4c7478ae14abd3cf61aef797
Signed-off-by: Hariharan K <quic_harihk@quicinc.com>
This change adds cmd_dpr as a common file,
so it will be reused in the future SoC.
dpr support added in Devsoc SoC.
Change-Id: I246a8f51c07c2f6952173bbd72e327ab1119af6e
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
This change adds a new command to support the qcn9224 fusing.
Fuser blower binary should be transfered via tftp to Host and
using fuse_qcn9224 command, binary can be transfered to qcn9224.
qcn9224 will take care of the fusing.
sample command:
tftpboot fuse_blower.bin
fuse_qcn9224 0
Change-Id: Ie8cd73a2d49799100bd1f717cdc4b8dad070f9bd
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
