Encryptio/Decryption
- For encryption/decryption, plain data/
encrypted date has to be written to memory
directly using mw command along with
ivadata, type and mode
- Implemented new uboot command "aes_256"
to receive the memory address where the
above data is written to
- Perfom basic sanity check against the data
received and send them to secure world through
scm calls
- This is supported only for HK/CYP, hence not
implemented for TZ running in 32bit mode
Change-Id: I589a15025cd248cf5792f13ea435c5c5b64c6066
Signed-off-by: Karthick Jeyaraman <kjeyaram@codeaurora.org>
soc_hw_version can used to prevent cross-platform
flashing of single images to prevent board
from getting bricked.
Signed-off-by: Gokul Sriram Palanisamy <gokulsri@codeaurora.org>
Change-Id: I579489498c8cbbc944b54e3050a319d1e11cb825
This changes removes NAPA support from tiny U-boot config
Signed-off-by: Vandhiadevan Karunamoorthy <vkarunam@codeaurora.org>
Change-Id: I057064d63a3ac0788275a4572242cc251a445a98
This change will enable config for serial training.
This change also fix the the logic to get most appropriate phase
out of passed phase.
This change also add support to read serial training offset from
partition table. Also patching freqency value & phase value to kernel.
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Change-Id: Ibb4a5cd80f16605e8e91bdf6a0c6c484edff1735
Removed identical device-tree to reuse original dts.
Affected boards: AC02 and OAK03
OAK03 to reuse HK01 dts and AC02 to reuse AC01 dts
Signed-off-by: Gokul Sriram Palanisamy <gokulsri@codeaurora.org>
Change-Id: I5a70514370f394b15e68d5819cf8d1b52da14f3f
We had identical device-tree for different RDPs
though they are the same except for machid.
This change enables reuse of a single device-tree
across RDPs with same configurations.
Signed-off-by: Gokul Sriram Palanisamy <gokulsri@codeaurora.org>
Change-Id: If81b431e4a6afe54e427fe0a52de275fdd29df00
This Gephy is internal phy driver for ethernet
Signed-off-by: Vandhiadevan Karunamoorthy <vkarunam@codeaurora.org>
Change-Id: Ia4e744c0fbd990bdc94fe93263ac2ddbe4cecf61
This changes initialize clock and enable the block of
Gephy, Uniphy, GMAC0 & GMAC1 and also udpate Rx & Tx clock
based on speed.
Signed-off-by: Vandhiadevan Karunamoorthy <vkarunam@codeaurora.org>
Change-Id: Ia2627e17f7029c2d0d1cbb9eff26afb27aa1c057
This changes enable ipq5018-tiny arch config which support
ipq5018 standard board files but support only particular dtbs
This change mainly removes eMMC, Pci ,I2C & UBI command and
additional features support
Signed-off-by: Vandhiadevan Karunamoorthy <vkarunam@codeaurora.org>
Change-Id: I4c92c77094d7fbc23b979f0c65f650cc89c28715
This change will enable page_scope_read & multipage_read support for
QPIC.
QPIC version 2.0 onwards , QPIC support page_scope_read &
multipage_read command to enhance the read performance.
In normal page read command SW is needed to write EXEC_CMD register
for each Code word and collect any Status related to that CW before
issueing EXEC_CMD for next CW.
For page_scope read command SW is required to issue EXEC_CMD
only once for a page. Controller HW takes care of Codeword specific
details and automatically returns status associated with each CW to
BAM pipe, dedicated for status deposition.
enabling all bits in NAND_AUTO_STATUS_EN will require 4 data
descriptors of 24 bytes each. This will publish all NANDc status
registers in system memory.
For multipage_read command SW is required to issue EXEC_CMD only
once for all the pages which configured in QPIC_NAND_MULTI_PAGE_CMD
register.
All interrupts will be operational and valid in these modes.
To check the status for each codeword, it is not possible to access
the status registers while the read command is operational in
page_scope & multi_page read modes. Hence, another feature to publish the
status data (for all NAND status registers) by programming the
NAND_AUTO_STATUS_EN register.
For serial NAND:
Read command for page_scope_read = 0x78800032 (QPIC_NAND_FLASH_CMD)
Read command for multi_page_read = 0x78400032 (QPIC_NAND_FLASH_CMD)
For Parallel NAND:
Read command for page_scope_read = 0x00800032 (QPIC_NAND_FLASH_CMD)
Read command for multi_page_read = 0x00400032 (QPIC_NAND_FLASH_CMD)
Now we fixed maximum data bytes read in one go 128KiB(2KiB page),
256KiB (4KiB page), 512 KiB (8kiB page), because from upper layer
we are getting more than 128KiB data bytes request in one go. if so
just changing the value of "MAX_MULTI_PAGE" macro will increase the
maximum data bytes in one go.
Change-Id: I48eea51ff8f5f79f3490d8a538c295ecc3eeee19
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
This change will add support for serial nand.
QPIC-2.1.1 supports parallel nand as well as serial nand.
QPIC will operate either in parallel configuration or
serial nand. Both can't work together.
This change will support initially four serial nand parts.
MT29F1G01ABBFDWB-IT (Micron-0x2C,0x15, 2K + 128)
GD5F1GQ4RE9IG (Giga Device-0xC8,0xC1, 2K + 128)
GD5F2GQ5REYIH (Giga Device-0xC8,0x22, 2K + 64)
GD5F1GQ4RE9IH (Giga Device-0xC8, 0xC9, 2K + 64)
Device Internal ECC is disabled for all three devices. This change will
enabele QPIC ECC engine.
For MT29F1G01ABBFDWB-IT 4-bit ECC as well 8-bit ECC will be supported.
For GD5F1GQ4RE9IG 4-bit ECC as well 8-bit ECC will be supported.
For GD5F2GQ5REYIH only 4-bit ECC will be supported due to 64-bytes spare.
For GD5F1GQ4RE9IH only 4-bit ECC will be supported due to 64-bytes spare.
Change-Id: I3f38f9c76b7bb235bb335a481fbc42ae1bd00395
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
This change will add support for collecting crashdump as
compressed gzip file, if specified through uboot environment
variable 'dump_compressed'
Change-Id: I0c3fb16bc07aaa0103e75a551477fce13f9e26da
Signed-off-by: Pavithra Palanisamy <pavip@codeaurora.org>
Currently I2C clocks are enabled by default in SBL.
Added clk settings in uboot to remove SBL dependency.
Change-Id: I6bc2ecaa5a9262dd1f134e5b62fd2cf38c682ff3
Signed-off-by: anusha <anusharao@codeaurora.org>
QCN3018 has only 2 cores, the kernel has to bringup
only 2 cores, hence if the SoC is identified as QCN3018
restrict the number of cores using "maxcpus" bootargs
Change-Id: Idafc44c02de302b65f9c9dfc5f77783a91b2c018
Signed-off-by: Sumit Gaur <gaur@codeaurora.org>
moving emmc related macros definitions to ipq807x & ipq40xx
board specific files from common files to avoid
redefined compilar warnings
Change-Id: Ic8d9537535a0b5439d42e8b0b53faadba72c50a3
Signed-off-by: Antony Arun T <antothom@codeaurora.org>
This change enables support to collect crashdump files
in connected usb storage device on requirement.
Change-Id: If191bcae5329dd2c9e84035069e4d9b0e73b546b
Signed-off-by: Pavithra Palanisamy <pavip@codeaurora.org>
This change will fix the following compiler warnings for AK and DK targets.
1.Wimplicit-function-declaration
2.Wdiscarded-qualifiers
3.Wstrict-prototypes
4.Wmaybe-uninitialized
5.Wunused-variable
6.Wint-conversion
Change-Id: I364904283172ccb19602ae1b6deceb8c61ea7638
Signed-off-by: sameeruddin shaik <samesh@codeaurora.org>
