The QPIC XFER STEPS will not be configured in non NAND boot
mode and the data transfer speed will be very slow. Now this
patch reads the timing parameter from ONFI page and configures
the NAND XFER STEPS registers for highest supported ONFI mode.
For NON ONFI device, it will configure to default mode.
Change-Id: I2daf4a92255307efc53db9bb7fe2f02e8c00c3fa
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
ipq40xx, ipq807x hardware share the qca8075 phy. So the qca8075 phy
mdio, driver has been moved to common directory for use by both the
hardware.
Change-Id: Id6e9342438ffbdf8599860df6fbb39bba30429b3
Signed-off-by: Jaiganesh Narayanan <njaigane@codeaurora.org>
flash_secondary_type is specific to ipq8064. Initialization of this
parameter is moved into boards specific file.
Change-Id: If1a0e44e3d0a674ce497de045d9c5095b67bc913
Signed-off-by: Gokul Sriram Palanisamy <gpalan@codeaurora.org>
Added the ipq807x ethernet edma, ppe driver support
Change-Id: Ibcac04d8a60c1ca74549834b70735a6f15b58358
Signed-off-by: Aditya Kumar Patra S <apatr@codeaurora.org>
This patch enables qca_mmc driver and
also has the changes required for emmc
support
Change-Id: Icc8d807caffced79d6ca576fe6220c522ebda3f7
Signed-off-by: Vasudevan Murugesan <vmuruges@codeaurora.org>
Added the ipq807x ethernet edma, ppe, gmac driver support
in the u-boot
Change-Id: I1d8ddd19f2c3d3765adda2253d3b71876142aa59
Signed-off-by: Jaiganesh Narayanan <njaigane@codeaurora.org>
As the U-boot source is going to be common between ARM and MIPS
architecture , it is required to pick only the files specific
to the respective architectures during the build.
So, move the qca arm target specific common files to another
sub level by specifying the ARCH arm.
Change-Id: I06b538834109981f21fef6270bfb8e437a2f5a7e
Signed-off-by: Prabhu Jayakumar <pjayak@codeaurora.org>
1. Modified common bootipq command file to support IPQ806x.
2. Modified common board initialization file to support IPQ806x.
Change-Id: I1fdd93037b885eefea0c5ddede9436861dd485b3
Signed-off-by: Aditya Kumar Patra S <apatr@codeaurora.org>
Only ipq40xx and ipq807x specific functionalities were
available in common SMEM. Made ipq806x specific changes
so that all QCA platforms can use this.
Change-Id: I00fc9c9ba8e2545d665c9791849d82e0ab5d974a
Signed-off-by: Aditya Kumar Patra S <apatr@codeaurora.org>
Adding a common file fdt.c and moving fdt fixup related routines
to this file to keep them generic.
Change-Id: I863135fc79f52eb35789605b8e240c637db0e02a
Signed-off-by: Gokul Sriram Palanisamy <gpalan@codeaurora.org>
This change eliminates the use of gboard_param
variable. Subsequent changes will make use of
dts.
Change-Id: Ic79a72c4fa1b86e864b55306a32c110bcfbc9184
Signed-off-by: Akila N <akilan@codeaurora.org>
1. Moved gpio structure declaration to gpio.h
2. Moved gpio configuration bit value macros to dt-bindings
Change-Id: I9da1cc3703a92e02cfa86765c8d4afe5321fed35
Signed-off-by: Gokul Sriram Palanisamy <gpalan@codeaurora.org>
Moved the clock header files into include folder to
escape from relative paths.
Change-Id: I776141741296e1138e45efb069479a0e26b4855c
Signed-off-by: Ajay Kishore <akisho@codeaurora.org>
Modified common serial driver to work for all AK, DK and HK boards.
Made the driver more generic. The board specific
configurations are moved to respective board.c files.
Change-Id: I8aa0001d215126eb1dd15d75d6ab3f9139d6f919
Signed-off-by: Aditya Kumar Patra S <apatr@codeaurora.org>
Fixed warnings for both ipq807x and ipq40xx
builds.
Change-Id: I69accebf525ee52f470335a14474378f5e7f65b0
Signed-off-by: Saravanan Jaganathan <sjaganat@codeaurora.org>
SMC calls are common for IPQ807x, IPQ40xx hence moving it to
common folder
Change-Id: I3d6564ad51ebe396f85cedbf41374374f40865c6
Signed-off-by: Manoharan Vijaya Raghavan <mraghava@codeaurora.org>
The SMEM is used for all the platforms like ipq40xx and ipq807x.
So moving this into a common place to use all qcom platforms.
Change-Id: I04f0bf0e7aad0eae71024d734d8049a3470d510d
Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
