In devsoc, we have 2 ports and 2 uniphys, so removed the extra
ports and uniphy configurations from the source. Also, updated
the clock src configuration with respect available uniphys and
removed the SFP port support.
Change-Id: I557bd6d215508c190a3e733a0304873ecd02eb24
Signed-off-by: Ram Kumar D <quic_ramd@quicinc.com>
In qca8084 phy mode, each phy is assigned to one mac in the ipq9574,
where as in the switch mode, only mac1 will used for all the 4 ports
of the qca8084, mac2-4 will be left unused. So, updated the
logic to update the link status of the individual ports, when qca8084
is in switch mode.
Change-Id: I128c3eafb7c85c0db9d252e047457ea8820df368
Signed-off-by: Ram Kumar D <quic_ramd@quicinc.com>
This patch renames the GCC macro which was added
for QCA8084 PHY to fix the conflict with similar
macro defined in ipq5018 platform.
Additionally, this patch also moves all QCA8084
macro definitions in MDIO driver under QCA8084_PHY
config.
Change-Id: Icd62bf260ffeae64bf67c0c1a58afb6ac4999e22
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This patch adds support for qca8084 PHY based
ports. Accordingly, updates the uniphy, ppe, clock
configurations as required for qca8084 ports.
Change-Id: I2e687c10adba579b0d47d8f5b529fe920b7d0d7c
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This patch adds initial support for qca8084 PHY
which is based on qca8081 PHY.
qca8084 PHY has support for 4x2.5G.
Change-Id: Ic767c19fad050e5ee9a97ad7fa50c1b6b27893dd
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
The PCIE node is disabled by default in
the emulation platform
Change-Id: I51041186a57d08b58c1f7c85dd1a90fbeb24aac9
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
This patch adds support for active_port env. With this
change in ipq9574, the end user has an option to
enable & maintain only 1 active ethernet port. There
are no multi-port use case in U-Boot and when multiple
ports were enabled for Kernel usecases, there were some
timeout issues in some special cases during crashdump
collection.
active_port can be used to configure the port which
will be used for TFTP download/upload in u-boot in
those setups. Example: To set Port2 as active_port
following command can be used:
setenv active_port 2 && savee
Note that, the active_port range is from 0 to 5 (there
are a total of 6 ports in ipq9574).
Change-Id: Ia2fc58abda7640f67afadfa01d0a5994aa48ea51
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
Added support for multiple i2c alias in device-tree
so as to enable multiple qup i2c modules.
Change-Id: I58b1b91c66e3b42cc5d603ce29f94e90b6d86ae1
Signed-off-by: Gokul Sriram Palanisamy <quic_gokulsri@quicinc.com>
The ring/desc's used non-cached memory which cannot
be free'd. Remove these free API's.
1 MB of memory is marked as non-cached and that is used
for EDMA rings/desc's and the same needn't be free'd. It
will be re-init each time during edma init.
Change-Id: Iac1e616db7c929d640c559024e4f65c6ad515400
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This patch moves the qca8075 phy inits inside the
config. Without this patch, when we disable the
QCA8075 config, then there will be compilation
errors.
Change-Id: Ibed0517c52f896f2af54773aa31260068e116479
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This patch removes the redundant udelay's and
ipq_mdio_wait_busy calls which in turn reduces
the overall AQ FW Load time.
Change-Id: I31f3a940d743528ed212e8cccab522ac249a5a5a
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This changes initialize non-cache buffer every time
before edma configuration.
Change-Id: If7692f9671f6b63f19ae38326bd76320c54766cc
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
This changes add support for uboot base files.
Change-Id: I5f4b937dec30a27ec6acce6ceada7fbed5d5a41d
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
This patch is a temporary WAR to fix timeout issues
observed in particular setups during dump collection.
This patch disables FDB Learning for ports 1-6.
Change-Id: I7987bb0286df129c56a07f1708600f78ebf42039
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
Setting this bit will not allow PPE to take any action on the
packets. Remove this configuration as its not needed in U-Boot
EDMA.
Change-Id: I45cb93a4f5072dd882179eca5a14bc4a25624f26
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This patch adds DA MAC rule. This rule can be used
if we want to drop packets with a particular DA MAC
address.
Change-Id: I32ef53ada1518f6880faa7402ccaaedb5b32a90b
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This patch adds ACL to drop the packets with src
mac address.
Change-Id: Ib944154ffb53b9bf67a178a5ab08cd9f12866b4a
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This change fixup the magic word (0xBAD0FF5E) instead of zero.
So the uboot will skip setting qcom,training_offset
if the serial training partition is not present in flash.
Change-Id: I0ee8c9475e1153fdbc295691ceb2a4b1d6fdd394
Signed-off-by: Saahil Tomar <quic_saahtoma@quicinc.com>
This patch updates the default uniphy mode to SGMII
for the qca808x ports. If suppose, the phy is capable
of supporting 2.5G, then it will reconfigure the
uniphy mode to SGMII_PLUS at that time based on the
link speed detected.
Change-Id: I56692b19536e71cbcf3a4c31d32ecb29866c5fdc
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
Flash Status register value will get updated in [15:8]
bits section. Hence right shift first and then extract
the required bit value.
Change-Id: I7f2233f22984da3db2324e9e2ba8aafff76adb32
Signed-off-by: Kavin A <quic_kavia@quicinc.com>
Winbond SPI Nand devices provides two different modes for read operations,
Buffer Read Mode (BUF=1) and Continuous Read Mode (BUF=0).
We can configure the BUF bit to read and operate in any one mode.
Change-Id: Ie7adce70642756725e52dab8821333c42fdb601f
Signed-off-by: Kavin A <quic_kavia@quicinc.com>
This change will add support for Winbond "W25N01GWZEIG" spi nand
Change-Id: Ic42938142115408406a8790e114d2d2acfc0dbb5
Signed-off-by: Kavin A <quic_kavia@quicinc.com>
This change will add support for Macronix "MX35UF2GE4AD-Z4I" spi nand
Change-Id: I5d783473c0ec918b02e59a85b71ee941fe649365
Signed-off-by: Kavin A <quic_kavia@quicinc.com>
This patch optimizes and updates the EDMA Driver as
required for ipq9574 platform similar to the Kernel
Host EDMA Driver.
-> Config TX_MOD and RX_MOD timers
-> Config DMAR_CTRL
-> Config Service code bypass for TX_DESC
-> Update the SRCINFO and DST_PORT configs
-> Make changes to include secondary and primary DESC's
into the same corresponding ring structure
-> Increase the TX_BUFF Size to 2048
-> Update to use RX_DESC RING 23
-> Remove unused fields from the EDMA structures
-> Update the description for the EDMA structure fields
Change-Id: I3f7f1c11cdd87687c38774a4930c9bee90857203
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This patch updates the following:
1) Updates NSS NOC clock frequencies to expected clock rates
2) Add Debug prints during eth_halt which can help debug issues
3) Update ACL structure and configurations for ipq9574 platform
as required
4) Disable the MIB counters reset bit so that those counter
registers values can be dumped to check stats
5) Update VSI configurations for cases when BRIDGED_MODE config
is disabled
6) Update the VSI configuration to avoid flooding from one LAN
port to another
Change-Id: I39f20a57c08205fbeb669c93b6459cf8e184098d
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
Added read & write bam pipe entires in all the ipq specific dtsi.
Also, updated the spi bam code with generic code changes to enable
the multiple spi support on all ipq chipsets.
Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Signed-off-by: Ram Kumar D <ramd@codeaurora.org>
Change-Id: Ibcdb9d2a9ff7a25f3d296ecdb1aca403511e07d7
This patch adds support for SFP 1G and 2.5G. Note that
there is no autoneg support for SFP in U-Boot and the mode needs
to be changed in DT to make it work in 1G or 2.5G.
By default SFP will be configured to work in 10G mode.
Change-Id: I1c209276fe2a586332be87ce5d49a140f4814eb2
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
When a long string (>255 char) input given to uboot console, RX
stale timeout occurred on UART subsystem due to RXFULL. This in-turn
cause uboot console to stuck.
So, Added a check to catch this scenario and re-start the UART RX
if it occurred.
Change-Id: Ic80c1d5f1178bf2455385c3888a2023ce1dbf6fa
Signed-off-by: Ram Kumar D <ramd@codeaurora.org>
This changes removes unwannted source for ipq806x
platform, therefore it saves more memory in flash
Signed-off-by: Vandhiadevan Karunamoorthy <vkarunam@codeaurora.org>
Change-Id: Ia34c9843a5b32c2db57ec4b4977ab8c04875161b
qpic_nand sbl -> to switch to 2K layout
qpic_nand linux -> to switch back to 4K layout
Currently this switch is enabled for IPQ9574
Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
(cherry picked from commit c9a1c10b2e35ba8f14dafc1f4c07aa5a07a01541)
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
Change-Id: I3e429b8cd5e600b4214c01d7949c01536f988e47
