This patch adds initial support for qca8084 PHY
which is based on qca8081 PHY.
qca8084 PHY has support for 4x2.5G.
Change-Id: Ic767c19fad050e5ee9a97ad7fa50c1b6b27893dd
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This patch updates the following:
1) Removes unnecessary TIMER and THRESHOLD configurations in EDMA
2) Adds Uniphy Clock deinit and init in eth_init (during each ping
& speed change)
3) Removes preheader configurations and calculations from EDMA
as there are no preheaders in ipq9574 platform (Instead there is
a secondary descriptor)
4) Add sufficient delay after uniphy reset
5) Remove CONFIG_IPQ9574_RUMI macro from network drivers
6) Change default mac_speed to 0
7) Fix the ppe sched. and tdm configuration
8) Reduce the block size to 1280 + headers for tftp (around 1326)
for timebeing without which timeouts were observed randomly during
TFTP (Note that the MTU is 1514 bytes)
Change-Id: I4004adfb2ae0dc98d65e458c15dafcff6523744b
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Previous platforms assume qca8075 phy address starts from
0. This patch adds a separate qca8075 phy driver for ipq9574
platform and handles cases where qca8075 phy addr doesn't
start with 0.
Change-Id: I59a596d692b1663af638af358335056661bdf199
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
This patch does the following:
1) Enables AQ Driver Compilation.
2) Updates malloc size to fixed value of 512 KB (size of ETHPHYFW Partition)
which is actually 1024 KB as per QSPI Nand Flash partition (considering the
bad block size also). While reading bad blocks will be skipped, and the
firmware size is not expected to exceed 512 KB and hence this size is updated.
Also note, the heap size is currently 1 MB and so if we try do malloc for 1 MB,
we might get failures during allocation.
3) Adds QSPI NAND Flash Support.
Change-Id: I5a6e19b1462b648523ce6b311128a447e34241b4
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
This patch moves the entire Uniphy configurations to
!CONFIG_IPQ9574_RUMI as there is no PHY/UNIPHY in EMU
Platform.
Change-Id: I404916d10caed87e4825172345195bf92df1b725
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
ipq40xx, ipq807x hardware share the qca8033 phy. So the qca8033 phy
driver has been moved to common directory for use by both the
hardware.
Change-Id: Ic972f00770c9e3cbaf4d727df21f19cd926ddce2
Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
This patch added the uniphy interface mode and port mux select
for PSGMII and SGMII.
Change-Id: I26f18a855b9972a358583d706d3f8a8bf09401cc
Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
ipq40xx, ipq807x hardware share the qca8075 phy. So the qca8075 phy
mdio, driver has been moved to common directory for use by both the
hardware.
Change-Id: Id6e9342438ffbdf8599860df6fbb39bba30429b3
Signed-off-by: Jaiganesh Narayanan <njaigane@codeaurora.org>
Added the ipq807x ethernet edma, ppe driver support
Change-Id: Ibcac04d8a60c1ca74549834b70735a6f15b58358
Signed-off-by: Aditya Kumar Patra S <apatr@codeaurora.org>
Added the ipq807x ethernet edma, ppe, gmac driver support
in the u-boot
Change-Id: I1d8ddd19f2c3d3765adda2253d3b71876142aa59
Signed-off-by: Jaiganesh Narayanan <njaigane@codeaurora.org>
As the U-boot source is going to be common between ARM and MIPS
architecture , it is required to pick only the files specific
to the respective architectures during the build.
So, move the qca arm target specific common files to another
sub level by specifying the ARCH arm.
Change-Id: I06b538834109981f21fef6270bfb8e437a2f5a7e
Signed-off-by: Prabhu Jayakumar <pjayak@codeaurora.org>
The memac for PHY management on little endian SoCs is similar on big
endian SoCs, so we modify the driver by using I/O accessor function to
handle the endianness, so the driver can be reused on little endian
SoCs, we introduce CONFIG_SYS_MEMAC_LITTLE_ENDIAN for little endian
SoCs, if the CONFIG_SYS_MEMAC_LITTLE_ENDIAN is defined, the I/O access
is little endian, if not, the I/O access is big endian. Move fsl_memac.h
out of powerpc include.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
LDPAA Ethernet driver is a freescale's new ethernet driver based on
Layerscape architecture.
Every ethernet driver controls on DPNI object. Where all DPNIs share
one common DPBP and DPIO object to support Rx and Tx flows.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Cristian Sovaiala <cristian.sovaiala@freescale.com>
CC: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
CC: J. German Rivera <German.Rivera@freescale.com>
[York Sun: s/NetReceive/net_process_received_packet]
Reviewed-by: York Sun <yorksun@freescale.com>
Move this to Kconfig and clean up board config files that use it. Also
rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists
in drivers/net/Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Version 1:
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Implement a bridge between U-Boot's network stack and Linux's raw packet
API allowing the sandbox to send and receive packets using the host
machine's network interface.
This raw Ethernet API requires elevated privileges. You can either run
as root, or you can add the capability needed like so:
sudo /sbin/setcap "CAP_NET_RAW+ep" /path/to/u-boot
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add basic network support to sandbox which includes a network driver.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new driver for the Gigabit Ethernet MAC found on Intel Topcliff
Platform Controller Hub. Tested under 10/100 half/full duplex and 1000
full duplex modes using ping and tftpboot commands.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
These are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Greg Ungerer <greg.ungerer@opengear.com>
Acked-by: Marek Vasut <marex@denx.de>
Upgrade Manage Complex (MC) flib API to 0.5.2. Rename directory
fsl_mc to fsl-mc. Change the fsl-mc node in Linux device tree
from "fsl,dprcr" to "fsl-mc". Print MC version info when
appropriate.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds a driver for VSC9953 L2 Switch. This Vitesse IP
is integrated in Freescale T1040 and T1020 SoCs.
The L2 switch has 10 Ethernet ports: 2 internal fixed-links
(ports 8 and 9) at 2.5 Gbps and and 8 external ports at 1 Gbps.
The external ports may be connected to PHYs over QSGMII and SGMII.
Commands have also been added to enable/disable a port and to
check a port's link speed, duplexity and status. The commands are:
ethsw port <port_nr> enable|disable - enable/disable an l2 switch port
ethsw port <port_nr> show - show an l2 switch port's configuration
port_nr=0..9; use "all" for all ports
For more detailse please see doc/README.t1040-l2switch
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds support for the NETA ethernet controller which is integrated
in the Marvell Armada XP SoC's. This port is based on the Linux driver which
has been stripped of the in U-Boot unused portions.
Tested on the Marvell MV78460 eval board db-78460-bp.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Tested-by: Luka Perkov <luka@openwrt.org>
The Broadcom StarFighter2 Ethernet driver is used in multiple Broadcom
SoC(s) and:
- supports multiple MAC blocks,
- provides support for the Broadcom GMAC.
This driver requires MII and PHYLIB.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
The following configs are not defined at all:
- CONFIG_INCA_IP_SWITCH
- CONFIG_PBL2800_ETHER
- CONFIG_PHY_ICPLUS
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
There have been 3 versions of the sunxi_emac support patch during its
development. Somehow version 2 ended up in upstream u-boot where as
the u-boot-sunxi git repo got version 3.
This bumps the version in upstream u-boot to version 3 of the patch:
- Initialize MII clock earlier so mii access to allow independent use
- Name change from WEMAC to EMAC to match mainline kernel & chip manual
- Cosmetic code cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Adding support to load and start the Layerscape Management Complex (MC)
firmware. First, the MC GCR register is set to 0 to reset all cores. MC
firmware and DPL images are copied from their location in NOR flash to
DDR. MC registers are updated with the location of these images.
Deasserting the reset bit of MC GCR register releases core 0 to run.
Core 1 will be released by MC firmware. Stop bits are not touched for
this step. U-boot waits for MC until it boots up. In case of a failure,
device tree is updated accordingly. The MC firmware image uses FIT format.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Ethernet driver configures the CPSW, SGMI and Phy and uses
the the Navigator APIs. The driver supports 4 Ethernet ports and
can work with only one port at a time.
Port configurations are defined in board.c.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
The device interface is 16 bits wide.
All the available packets are read from the incoming fifo.
Signed-off-by: Roberto Cerati <roberto.cerati@bticino.it>
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
[voice.shen@atmel.com: address comments from review results]
[voice.shen@atmel.com: clean up for submit]
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
This patch adds support for the WEMAC, the ethernet controller included
in the Allwinner A10 SoC. It will get used in the upcoming A10 board
support.
From: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Device driver for Zynq Gem IP.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Joe Hershberger <joe.hershberger@gmail.com>
CC: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
