Changes:
* update to v2026.01 (this brings up EN7523 SoC support)
* drop upstream patches
* refresh and adapt an7583 support patches (changes based on
https://github.com/Ansuel/openwrt/commits/main-airoha-6.12/)
* add ethernet switch mdio support from upstream U-Boot
Notable changes:
* make an7583 memory initialization similar to an7581 one
* add an7583 scu/chip_scu helpers to access scu/chip_scu regmaps.
* fix misprint in an7583 'system-controller@1fb00000' node name
* always use board dts for nand partitioning
Notes about en7523 support
--------------------------
This set of patches brings up more or less complete support of EN7523 SoC.
Unfortunately, building of en7523 bootloader will require en7523-bl2.bin
and en7523-bl31.bin blobs which is not available at the moment.
This is the only known blocker for adding en7523 bootloader support.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/21984
Signed-off-by: Robert Marko <robimarko@gmail.com>
CMCC MR3000D-CI is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
IPQ5000.
Device specification
--------------------
- SoC : Qualcomm IPQ5018
- RAM : 512 MiB DDR3L
- Flash : 128 MiB SPI-NAND (GigaDevice GD5F1GQ5REYIG)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm IPQ5018 (SoC)
- 5 GHz : Qualcomm Atheros QCN6102
- Ethernet : 4x 10/100/1000 Mbps
- Switch : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO) : 2x LEDs, 2x Buttons
- UART : Through-hole on PCB
- Voltage : 3.3 V
- Assignment : Silkscreened on PCB
- Settings : 115200n8
- Power : 12 VDC, 1.5 A
Installation
-----------------
1. Telnet method
a. Enable telnet
Log in to http://192.168.10.1/ with the password on the sticker
Modify URL according to example (keep your unique hash after ";stok=")
and press Enter:
http://192.168.10.1/cgi-bin/luci/;stok=78becad1b1490e45be2776025cde2b7d/api/NPCnetwork/ping?url=$(telnetd)
You should get the following in the browser:
{"link":0}
b. Run tftp server on IP 192.168.10.254 and put factory image
'openwrt-qualcommax-ipq50xx-cmcc_mr3000d-ci-squashfs-factory.ubi'
in the tftp root dir.
c. Login to 192.168.10.1 with telnet (user: root, pass: from the
sticker).
d. Download factory image from the tftp:
tftp -l factory.ubi -r openwrt-qualcommax-ipq50xx-cmcc_mr3000d-ci-squashfs-factory.ubi -g 192.168.10.254
e. Flash factory image:
export rootfs=$(cat /proc/mtd | grep rootfs | grep -v _ | cut -d: -f1)
ubidetach -f -p /dev/${rootfs}
ubiformat /dev/${rootfs} -y -f /tmp/factory.ubi
f. Reboot:
reboot
2. U-Boot Method using UBI Image (using UART)
a. Place the factory.ubi file on your TFTP server, enter U-Boot CLI
and exec these commands:
tftpboot <your_tftp_server_ip>:factory.ubi
flash rootfs
reset
3. U-Boot Method using initramfs Image (using UART)
a. Place the openwrt-*-initramfs-fit-uImage.itb file on your TFTP
server and rename it to initramfs.bin
b. Enable serial console, enter to U-Boot CLI and exec these commands:
tftpboot <your_tftp_server_ip>:initramfs.bin
bootm
c. Once boot completed, upload the sysupgrade.bin file to router's
/tmp directory (using scp or wget) and execute the following command
in openwrt shell:
sysupgrade -n /tmp/sysupgrade.bin
MAC Addresses
-------------
+--------------+-------------------+-------------+
| Interface | MAC example | Location |
+--------------+-------------------+-------------+
| LAN | 84:7a:xx:xx:xx:dd | 0:ART, 0x6 |
| WAN (label) | 84:7a:xx:xx:xx:dc | 0:ART, 0x0 |
| WLAN 2.4 GHz | 84:7a:xx:xx:xx:de | 0:ART, 0xc |
| WLAN 5 | 84:7a:xx:xx:xx:df | 0:ART, 0x12 |
+--------------+-------------------+-------------+
Notes
-----
1. U-Boot is protected by a password (pass: netpower).
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21952
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Zyxel NWA110AX is a dual band 2x2:2 802.11ax wireless access point
with PoE.
The device is very similar to the NWA210AX except for being 2x2 instead
of 4x4 in the 5GHz band and not having the 2.5GbE ethernet port. This
commit factors out a common DTS and device definition and reuses it for
both devices.
Hardware:
* SoC: Qualcomm IPQ8070A
* RAM: 1GiB 1x Samsung K4A8G165WC-BCTD
* Flash: 8MiB Winbond W25Q64DW SPI-NOR, 256MiB Winbond W29N02GZ SPI-NAND
* WLAN 2.4GHz: QCN5024 2x2:2 802.11b/g/n/ax
* WLAN 5GHz: QCN5054 2x2:2 802.11n/ac/ax
* Ethernet: 1x 1GbE with AR8033 PHY
* Serial Config: 3.3V TTL 115200-8-N-1, externally accessible
* Serial Layout: GND TX RX 3.3V (don't connect, marked with triangle)
* LEDs: 1x red, 1x green, 1x blue, 1x white
* Buttons: 1x reset
MAC addresses:
* Uplink: base address on label
* 2.4GHz WLAN: base + 1
* 5GHZ WLAN: base + 2
Flashing Notes:
The device uses a dual-image setup and OpenWrt can only be installed as
image 0. When the currently running stock firmware is image 0, OpenWrt
will be installed as image 1, fail to boot and the device returns to stock
firmware. If this happens, install any version of stock firmware so that
it runs as image 1, before installing OpenWrt. Alternatively, if there
already is a valid stock firmware in image 1, the "debug dual-image show"
and "debug dual-image set boot-image image1" commands can be used in the
stock CLI via serial/SSH/telnet to switch to image 1.
Flashing with Stock Web Interface:
* Get the OpenWrt factory image and rename it to a shorter name, for
example "openwrt.bin" (the stock firmware has a character limit)
* In the web interface, go to "Maintenance" -> "File Manager" ->
"Firmware Package" (or click the link next to "Firmware Version" under
"Device Information" on the dashboard)
* Under "Upload File" browse to the renamed OpenWrt factory image and
click on "Upload"
Switch Boot Image:
* OpenWrt to stock: "zyxel-bootconfig-ipq807x set image1"
* Stock to OpenWrt: "debug dual-image set boot-image image0"
Unbrick / Revert to Stock with the Boot Module:
* Disconnect the device from power
* Configure your machine to 192.168.1.103/24 and start a TFTP server
* Put the stock firmware image into the TFTP server root and rename it to
"ZLD-current"
* Establish a serial connection to the device through the console port
* Connect the device to power
* When prompted, press a key to abort automatic boot and enter debug mode
* Use the "atnz" command to flash the firmware image
* Use the "atgo" command to boot from the newly flashed image
Signed-off-by: Michael Lotz <mmlr@mlotz.ch>
Link: https://github.com/openwrt/openwrt/pull/21849
Signed-off-by: Robert Marko <robimarko@gmail.com>
Netgear RBx350 are dual band 4 stream 802.11ax mesh devices from the Orbi
series. The RBR350 is a router with a WAN and 3 LAN ports. The RBS350 is a
satellite without WAN port, only 2 LAN ports and half the flash. The
hardware is otherwise identical. They were sold in kits as RBK352, RBK353,
RBK354 or RBK355, with one router and 1-4 satellites.
Hardware:
* SoC: Qualcomm IPQ6018
* RAM: 512MiB 1x Nanya NT5CC256M16ER-EK
* Flash: 512MiB Winbond W29N04GZ or 256MiB Winbond W29N02GZ
* WLAN 2.4GHz: QCN5022 2x2:2 b/g/n/ax
* WLAN 5GHz: QCN5052 2x2:2 a/n/ac/ax
* Ethernet: QCA8075 switch with 1 WAN and 3 LAN ports or 2 LAN ports
* Serial Config: 3.3V TTL 115200-8-N-1, internal populated header
* Serial Layout: 3.3V (don't connect, marked with dot) RX TX GND
* LEDs: green/red power, white/red/green/blue status
* Buttons: 1x Reset, 1x WPS
MAC addresses:
* LAN1: base address on label, stored in boarddata partition at 0x8
* LAN2: base + 1
* LAN3: base + 2
* WAN: base + 3
* 2.4GHz WLAN: base + 1
* 5GHz WLAN: base + 2
Flashing Notes:
The stock firmware images are signed. Both the bootloader and the stock
web interface check the signature and will fail to boot/flash.
The bootloader automatically does NMRP when a gigabit LAN connection is
present. The stock and factory images contain a U-Boot script that is
executed when flashing using NMRP. This is used to alter and persist the
U-Boot env with a boot command that works with unsigned firmware.
Install OpenWrt:
* Get the nmrpflash utility [0] and OpenWrt factory image
* Find network interface to use: nmrpflash -L
* Start nmrpflash: nmrpflash -i interface -f openwrt-...-factory.img
* Connect the device LAN port closest to the power jack to the same
network using gigabit
* Plug the device in and wait for the bootloader to flash
* Unplug and replug the device once the power LED blinks amber
Revert to Stock:
The boot command needs to be reverted before flashing the stock firmware,
otherwise it will fail to boot and get stuck in recovery mode (red power
LED flashing).
* Run: fw_setenv bootcmd bootipq
* Restart the device
* Flash the stock firmware RBx350-Va.b.c.d.img using nmrpflash
[0]: https://github.com/jclehner/nmrpflash
Signed-off-by: Michael Lotz <mmlr@mlotz.ch>
Link: https://github.com/openwrt/openwrt/pull/21656
Signed-off-by: Robert Marko <robimarko@gmail.com>
Netgear RBx750 are tri band, 2.4GHz and 2x 5GHz, 8 stream 802.11ax mesh
devices from the Orbi series. The RBR750 is a router with a WAN and 3 LAN
ports. The RBS750 is a satellite without WAN port, only 2 LAN ports and
half the flash. The hardware is otherwise identical. They were sold in
kits as RBK752-RBK757, with one router and 1-6 satellites.
Hardware:
* SoC: Qualcomm IPQ8074
* RAM: 1GiB 1x Samsung
* Flash: 512MiB Winbond W29N04GZ or 256MiB Winbond W29N02GZ
* WLAN 2.4GHz: QCN5024 2x2:2 b/g/n/ax
* WLAN 5GHz Low Band: QCN5054 2x2:2 a/n/ac/ax 5180-5320MHz
* WLAN 5GHz High Band: QCN5054 4x4:4 a/n/ac/ax 5500-5700MHz
* Ethernet: QCA8075 switch with 1 WAN and 3 LAN ports or 2 LAN ports
* Serial Config: 3.3V TTL 115200-8-N-1, internal populated header
* Serial Layout: Bottom <- RX, TX, GND, 3.3V (don't connect) -> Top
* LEDs: green/red power, white/red/green/blue status
* Buttons: 1x Reset, 1x WPS
MAC addresses:
LAN1: base address on label
LAN2: base + 1
LAN3: base + 2
WAN: base + 1
2.4GHz: base + 2
5GHz-Low: base + 3
5GHz-High: base + 4
Flashing Notes:
The stock firmware images are signed. Both the bootloader and the stock
web interface check the signature and will fail to boot/flash.
The bootloader automatically does NMRP when a gigabit LAN connection is
present. The stock and factory images contain a U-Boot script that is
executed when flashing using NMRP. This is used to alter and persist the
U-Boot env with a boot command that works with unsigned firmware.
Install OpenWrt:
* Get the nmrpflash utility [0] and OpenWrt factory image
* Find network interface to use: nmrpflash -L
* Start nmrpflash: nmrpflash -i interface -f openwrt-...-factory.img
* Connect the device LAN port closest to the power jack to the same
network using gigabit
* Plug the device in and wait for the bootloader to flash
* Unplug and replug the device once the power LED blinks amber
Revert to Stock:
The boot command needs to be reverted before flashing the stock firmware,
otherwise it will fail to boot and get stuck in recovery mode (red power
LED flashing).
* Run: fw_setenv bootcmd bootipq
* Restart the device
* Flash the stock firmware RBx750-Va.b.c.d.img using nmrpflash
[0]: https://github.com/jclehner/nmrpflash
Signed-off-by: Michael Lotz <mmlr@mlotz.ch>
Link: https://github.com/openwrt/openwrt/pull/21938
Signed-off-by: Robert Marko <robimarko@gmail.com>
RIPE Atlas Probe v5 is a network measurement device based on Turris MOX.
u-boot bootscript supports booting both from the original Turris BTRFS
layout and default OpenWrt ext4 boot + root partition layout.
Specifications:
* SoC: Marvell ARMADA 3720
* RAM: 512 MiB, DDR3
* eMMC: 4G
* Ethernet: 1x 1GbE
MAC:
LAN MAC: label on board
Flash instructions:
* For using the default ext4 layout, boot into a live system using
tftpboot in u-boot and flash an OpenWrt SD image onto /dev/mmcblk0.
* For the Turris layout, put the new rootfs into subvolume '@', not
forgetting to add Image, device tree, and boot.scr to /boot.
Misc:
* USB connection is only for power. For UART access use the pin header:
1: GND
2: +1.8V
5: TX
6: RX
* Flashing the image onto Turris Shield won't work. Use Turris MOX image
instead.
Signed-off-by: Tomáš Macholda <tomas.macholda@nic.cz>
Link: https://github.com/openwrt/openwrt/pull/20031
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These devices share the same "compatible" in device tree causing some
incompatibilities (sysupgrades, ASU profile identification), assign a
unique "compatible" and "model" to each variant.
Context:
Commit [1] added each variant's dts compatible to the SUPPORTED_DEVICES
field of the other variant to make easy sysupgrades between these
physically indistinguishable devices variants possible.
But there were found three issues which does not allow this:
- the sysupgrade's stricter check still used in some sysupgrade
paths(this check is being replaced(and redundant) with the newer fwtool's
SUPPORTED_DEVICES check using the info in images METADATA), this check
will fail when sysupgrading from a different board_name(compatible dts)
that the image was created for (image profile name).[2]
- ASU needs unique "dts compatible" to identify the devices profile.
- and an ASU's profile identification limitation when several devices from
a common target share SUPPORTED_DEVICES entries.[3]
There is a proposal for these issues but not yet implemented [4][3].
Until these issues are fixed we won't allow "easy" sysupgrades between
these two device variants.
Commit [5] avoided the ASU profile identification limitation but
missed the required two unique dts compatibles in order to make the two
variants fully work, although not allowing easy sysupgrade between them.
[1]: 8d30e07180
[2]: sysupgrade stricter check https://github.com/openwrt/openwrt/issues/20566#issuecomment-3583555482
[3]: ASU proposal https://github.com/openwrt/asu/pull/1533
[4]: allow easy sysupgrade proposal https://github.com/openwrt/openwrt/pull/20947
[5]: b71f4665cd
Fixes: b71f466 ("mediatek: filogic: fix supported_devices list for gl-mt2500")
Fixes: 8d30e07 ("mediatek: filogic: fix for new GL.iNet GL-MT2500/GL-MT2500A hardware revision")
Fixes: https://github.com/openwrt/openwrt/issues/20566
Fixes: https://github.com/openwrt/asu/issues/1525
Signed-off-by: Mario Andrés Pérez <mapb_@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21842
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These two are redundant definitions according to dts. A value of 4 (CRC
no redundancy) makes no sense.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16618
Signed-off-by: Robert Marko <robimarko@gmail.com>
There are two redundant sections. One at 0x0 and the other at 0x80000.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16618
Signed-off-by: Robert Marko <robimarko@gmail.com>
TCL LINKHUB HH500V also known as Vodafone Gigacube B157 is a dual band
802.11ax 5G NR CPE with an FXS port.
Specifications:
* SoC: Qualcomm IPQ8072A
* RAM: 1024 MB
* NAND flash: 256MB NAND (MT29F2G08ABBGAH4)
* NOR flash: 64MB NOR (MX25U25635F) - only in some variants
* WiFi 5G: Qualcomm QCN5054
* WiFi 2.4G: Qualcomm QCN5024
* Ethernet 2.5G: Qualcomm QCA8081
* Ethernet 1G: Qualcomm QCA8075
* Modem: GosunCn GM800 (Qualcomm Snapdragon X55)
* SIM: 1 nano-SIM card slot
* Buttons: Power, Reset, WPS
* LEDs: Power (B/R), WiFi (B), 4G (B/Y/R), 5G (B/Y/R)
* VoIP: 1 FXS RJ11 port (not supported in OpenWrt)
* Power: 12V, 3A
UART serial console:
* 115200,8N1,1.8V
* Three unmarked test points next to QJ2012A:
+---------+
| QJ2012A |
+---------+
o TX
o GND
o RX
o
o
o
Installation via OEM firmware:
* Use the following process to obtain root ssh access
https://forum.openwrt.org/t/150371/24
* Connect using root with no password on port 42000
* Optionally for serial bootloader access run :
fw_setenv bootdelay=3
* SCP factory.bin to /tmp
* Run:
sysupgrade -n /tmp/factory.bin
Installation via serial console and OEM firmware::
* Use console to access OEM firmware shell
* Proceed with SCP & sysupgrade as described above
Other notes:
* This device uses active partition rotation
* Some versions (TCL branded?) have a NOR chip in addition to NAND
* The above is supported by u-boot patching DT partitions
* DT patching does NOT occur on tftpboot/bootm
* Modem is detected as foxconn-sdx55 by kernel (same VID/PID)
* This works OK-ish and should be improved if we can get OEM modem details
Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
* SoC: Qualcomm IPQ6018/AP-CP03-C1 (64-bit Quad-core Arm Cortex-A53 @ 1.2 GHz)
* RAM: 2x Zentel A3T4GF40BBF-HP (1 GiB DDR3-1866 (13-13-13))
* Serial Port: 1v8 TTL 115200n8
* Wi-Fi: Qualcomm QCN5022 (802.11ax/b/g/n)
* Wi-Fi: Qualcomm QCN5052 (802.11ac/ax/n)
* Ethernet: RTL8211FS (10/100/1000BASE-T)
* Flash: GigaDevice PSR1GA30DT (128 MiB)
* LEDs: 1x Blue Status (GPIO 35 Active High)
* Buttons: 1x Reset (GPIO 9 Active Low)
* FCCID: 2AXJ4EAP620HDV3
* UART: 4-pin unpopulated header by the J1 footprint
Installation Instructions (Serial+TFTP):
1. Locate the J1 footprint which contains 4 unpopulated pins
where starting from the arrow, the pins are TX, RX, VCC and GND
respectively.
2. Connect a 1v8 TTL port to the 4 pins. Ensure RX and TX are crossed
over.
3. Copy openwrt-qualcommax-ipq60xx-tplink_eap620-hd-v3-initramfs-uImage.itb
to your TFTP server.
4. Power up the AP and hold Ctrl+B in the serial console (115200n8) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
IPQ6018# setenv serverip <TFTP server addr>
IPQ6018# setenv ipaddr <addr of the AP>
IPQ6018# tftpboot 0x44000000 openwrt-qualcommax-ipq60xx-tplink_eap620-hd-v3-initramfs-uImage.itb
IPQ6018# bootm 0x44000000
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp -O openwrt-qualcommax-ipq60xx-tplink_eap620-hd-v3-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq60xx-tplink_eap620-hd-v3-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Installation Instructions (Web UI method):
1. Set up the device using the vendor's web UI. Navigate to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
2. Connect to the machine via SSH:
$ ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
3. Disable signature verification:
$ cliclientd stopcs
4. Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
5. Go to System -> Firmware Update.
Under "New Firmware File", click "Browse" and select the image.
Select "Update" and confirm by clicking "OK".
6. If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWrt.
Device support followed from EAP620HD v2 and eap6xx-outdoor for DTS.
Links: openwrt/openwrt#18227
Signed-off-by: John Christoforidis <github@yanny.dev>
Link: https://github.com/openwrt/openwrt/pull/21467
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch was manually edited but not refreshed.
Fixes: 794b4dee65 ("uboot-mediatek: add 8g check to bpi-r4 environment for bl2")
Fixes: 46ee5209aa ("uboot-mediatek: add command for getting size of ram")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21693
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add pending support for the HINLINK H66K / H68K.
Tested on HINLINK H66K, H68K and H68K-V2.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/21270
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add check for 8g and replace filename for bl2 to install the right file.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://github.com/openwrt/openwrt/pull/21437
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add command which gets ramsize and write it to env variable.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://github.com/openwrt/openwrt/pull/21437
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This allows builds for Bananapi R4 (Pro) with 8GB RAM.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://github.com/openwrt/openwrt/pull/21437
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This allows builds for Bananapi R4 (Pro) with 8GB RAM.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://github.com/openwrt/openwrt/pull/21437
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove upstreamed patches:
100-08-cmd-mtd-add-markbad-subcommand-for-NMBM-testing.patch [1]
101-01-mtd-spinand-add-support-for-FORESEE-F35SQA002G.patch [2]
101-02-mtd-spinand-add-support-for-FORESEE-F35SQA001G.patch [3]
110-mtd-spi-nand-add-support-for-FudanMicro-FM25S01A.patch [4]
Some SPI-NAND driver macro definitions and function parameters have
been changed in the latest release[3]. Hence we also had to rework
the related local patches to follow the upstream changes.
Tested on MT7981 SPI-NOR/EMMC.
[1] 21c1098cf4
[2] 2a0f8e7da0
[3] 2cbdd3e449
[4] 8b984b5a39
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
[daniel@makrotopia.org: tested MT7622 SNAND and SPI-NOR]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update to version 2024.01 to remove upstream patches.
The remaining patches come from this repository:
https://github.com/smaeul/u-boot/tree/d1-wip
[for Dongshan Nezha STU, Nezha D1]
Tested-by: Zoltan HERPAI <wigyori@uid0.hu>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
To update kexec and kdump dependencies for supporting the aarch64 architecture.
Signed-off-by: Roc Lai <laipeng668@qq.com>
Link: https://github.com/openwrt/openwrt/pull/21623
Signed-off-by: Robert Marko <robimarko@gmail.com>
Microchip ATF depends on Ruby scripts to generate the FWU monitor HTML
and more, so make sure that host Ruby is available.
We also need to call the scripts directly via Ruby executable as shebang
wont work due to lack of Ruby in the Buildbot container.
Fixes: 5205c0c426 ("microchipsw: lan969x: add Microchip EV23X71A")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
LibreSSL 3.9+ has dropped support for X509V3 extension API so cert_create
tool does not compile against it at all.
This was hidden by the fact that it was compiling against OpenSSL on my
host which still has that API, however we do not ship libssl-dev in the
Buildbot containers so compiling against distro OpenSSL is not possible.
So, after a long time trying to find any docs on that API I resorted to
LLM(Gemini 3 Pro) to get it to compile.
Our libcrypto is linked against pthread so we must pass -lpthread as well
for cert_tool.
Fixes: 5205c0c426 ("microchipsw: lan969x: add Microchip EV23X71A")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Mark T4240RDB u-boot variants as device-built and avoid installing them into rootfs.
Without this buildbot crashes during package install with:
ERROR: unable to select packages:
u-boot-fsl_T4240RDB-nor (no such package):
required by: world[u-boot-fsl_T4240RDB-nor]
u-boot-fsl_T4240RDB-sdboot (no such package):
required by: world[u-boot-fsl_T4240RDB-sdboot]
Fixes: c5d3d5fe28 ("package: u-boot: initial support for qoriq arch")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21514
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware specifications:
- CPU: Freescale/NXP P2020, dual-core PowerPC @ 1 GHz
- RAM: 1 GB DDR3
- Flash: 2 MB NOR, 512 MB NAND
- Networking: 7x Gigabit Ethernet ports (via two Marvell 88E6171
switches, each attached to a different MAC)
- USB: 2x USB 2.0 ports (front panel)
- mini-PCIe slot
- RTC: Ricoh RS5C372A
- 4 buttons (via external MCU)
- 3 LEDs (via external MCU)
- LCD display (via external MCU)
Installation procedure:
1. Obtain the original MAC address table from the stock bootlog, for
example:
setting device eth0 to 00:90:7f:00:00:01
setting device eth1 to 00:90:7f:00:00:02
setting device eth2 to 00:90:7f:00:00:03
setting device eth3 to 00:90:7f:00:00:04
setting device eth4 to 00:90:7f:00:00:05
setting device eth5 to 00:90:7f:00:00:06
setting device eth6 to 00:90:7f:00:00:07
2. Open the case and move jumper JP1 from 2-3 to 1-2 to enter FAILSAFE
mode.
3. Power on the device and interrupt the boot process to access the U-Boot
shell.
4. Program the MAC base address into the EEPROM (text after '#' is a
comment):
mac ports 3
mac 2 00:90:7f:00:00:01 # first MAC address from bootlog
mac save
5. Reset the device and enter the U-Boot console again.
6. Connect a TFTP server to port 6 and boot the initramfs image:
setenv ipaddr 192.168.1.3
setenv serverip 192.168.1.2
setenv loadaddr 1000000
tftpboot $loadaddr openwrt-mpc85xx-p2020-watchguard_xtm330-initramfs-kernel.bin
bootm $loadaddr
7. (Optional) Backup all MTD partitions if you want the ability to restore
stock firmware.
8. Perform a normal sysupgrade from the initramfs environment.
9. Power off the device and move jumper JP1 back to 2-3.
10. The device will now boot OpenWrt.
Known issues:
- LCD, buttons and LEDs are controlled by an external MCU; the protocol is
currently unknown.
- The internal connection between the two Marvell switches is unused by
OpenWrt.
- The stock firmware uses an empty U-Boot environment; saving variables
modifies the environment and prevents a normal boot. FAILSAFE U-Boot
remains functional.
- WatchGuard configuration is encrypted; DSA MAC addresses are stored in
this configuration.
- Failsafe Ethernet works on port1.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21020
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Novarq Tactical 1000 is a LAN9696 based switch.
Specifications:
* CPU: Microchip LAN9696 switch SoC
* DRAM: 2GB DDR4
* Storage:
* 32MB QSPI NOR
* 16GB eMMC
* Networking:
* 24 x 10/100/1000 RJ45 via LAN8804 Quad PHY-s over QSGMII
* 4 x 100/1000/2500/5000/10000 SFP+ ports
* 1 x 10/100/1000 management RJ45 via LAN8840 PHY over RGMII (U-Boot too)
* USB: 1 x USB2.0 Type-A
* Management via USB-C (MCP2200):
* UART @ 115200 baud (Default), 921600 possible
* GPIO-s for bootstrap and reset
* LED-s:
* 2 per networking port (Green and Yellow)
* Green status LED
* Soft reset GPIO
* Power: 12V DC barrel jack
* External PoE:
* Option for PoE add-on
* Temperature Sensors:
* TMP1075 onboard
* CPU temperature
* Microchip MCP79402 RTC with battery back-up
* Microchip ATECC608C secure peripheral
* CPU heatsink with PWM fan
* Onboard header for case fan
Installation instructions:
1. Connect to UART via the USB-C port
2. Connect the management port
3. Boot and interrupt U-Boot
4. TFTP the OpenWrt initramfs image and boot it
5. SCP the OpenWrt eMMC GPT image to a running OpenWrt initramfs to /tmp
openwrt-microchipsw-lan969x-novarq_tactical-1000-squashfs-emmc-gpt.img.gz
And decompress it via:
gzip -d /tmp/openwrt-microchipsw-lan969x-novarq_tactical-1000-squashfs-emmc-gpt.img.gz
6. Wipe eMMC with:
dd if=/dev/zero of=/dev/mmcblk0 bs=1M
7. Flash OpenWrt eMMC image with:
dd if=/tmp/openwrt-microchipsw-lan969x-novarq_tactical-1000-squashfs-emmc-gpt.img
of=/dev/mmcblk0
After a restart OpenWrt will boot, and then regular sysupgrade can be used
for upgrades.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Update microchipsw TF-A to the latest bugfix release that fixes
SHA checksum validation if large files are uploaded via the monitor mode.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This package adds initial u-boot support for qoriq target.
U-boot for qoriq devices must be compiled with 32-bit compiler and
linked with 32-bit linker. It's part of mpc 85xx target. But qoriq
target is 64-bit. As workaround, mpc85xx binary toolchain is downloaded
only for this u-boot.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/10941
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Create a common dtsi for Bananapi BPi-R4 Lite and add missing
gpio-leds. This reduced code and fixed the following LED bug:
LED 'green:status' not found (err=-19)
Fixes: 3a71dd58 ("uboot-mediatek: add support for the BananaPi BPi-R4 Lite")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
This is tri-band WiFi6E capable router. Also Zyxel Nebula managed so no real local GUI. To open device 4 screws must be located uder the label.
Four latches are on front and two on each side. Better start from ethernet port side where 3 small latches are easy to handle.
FCC shows It's identical to WSQ65 sold as Zyxel Multy M6E but that's nowhare to be found yet. WSQ65 is not covered by this PR
Speficiations:
* SoC: Qualcomm IPQ5018
* RAM: 1GB DDR3
* Flash: Winbond W25N02KWZEIR 256MB
* UART: PCB "J3" is located left from front LED strip
(VCC/TX/RX/ /GND) 3.3V 115200n8
* Wi-Fi1: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
* Wi-Fi2: QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
* Wi-Fi3: QCN6122 (2x2:2 6 Ghz 802.11an/ac/ax)
* Ethernet: QCA8337 4xLAN 1Gbit / 1xWAN 1Gbit
* Buttons: WPS , Reset
* LEDs: 13 in total
RGB power, RGB wan, RGB status (cloud), RGB wifi, Green wps
* FCCID: I8803891
*Flash Instructions starts with getting root:
connect uart to J3 connector next to the front LEDs
go to failsafe when this shows up in log:
"Press the [f] key and hit [enter] to enter failsafe mode"
execute:
mount_root
passwd -d root
reboot
logon as root:
look for 'Please press Enter to activate this console.'
login is root password is empty
execute:
fw_setenv DebugFlag=0x1
fw_setenv bootdelay=0x2
passwd -d root
backup ubi partition "rootfs" into safe space
reboot
*OpenWrt installation
stop uboot and execute:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.10
tftpboot *-factory.ubi
flash rootfs
reset
or:
tftpboot *-initramfs-uImage.itb
bootm
use sysupgrade as usual
*restore OEM from backup
stop uboot and execute:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.10
tftpboot *-initramfs-uImage.itb
bootm
transfer rootfs.bin backup and execute:
ubiformat /dev/mtd16 -y -f /tmp/rootfs.bin
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
Link: https://github.com/openwrt/openwrt/pull/21042
Signed-off-by: Robert Marko <robimarko@gmail.com>
Bump to the latest version used by other OpenWrt platforms so
we don't bitrot.
Tested on the D-Link DIR-890L.
Link: https://github.com/openwrt/openwrt/pull/21377
Signed-off-by: Linus Walleij <linusw@kernel.org>
This commit adds a new non-ubi spim-nand build for mt7987.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21235
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
U-Boot website has been moved to docs.u-boot.org.
Signed-off-by: Yanase Yuki <dev@zpc.st>
Link: https://github.com/openwrt/openwrt/pull/21279
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows us to use the full size of nand,
which extends ubi size from 64Mb to 122.25Mb.
If you are at factory firmware, please refer
to [PR](https://github.com/openwrt/openwrt/pull/21141)
to boot into OpenWrt first.
1. Log in to the device and backup all the partitions,
especially unique `Factory` and `bdata` partitions
from System -> Backup / Flash Firmware -> Save mtdblock contents.
2. Install kmod-mtd-rw to unlock mtd partitions for writing:
```bash
apk update && apk add kmod-mtd-rw && insmod mtd-rw i_want_a_brick=1
```
3. Write new OpenWrt (U-Boot Layout) `BL2` and `FIP`:
```bash
mtd write openwrt-mediatek-filogic-cudy_wbr3000uax-v1-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cudy_wbr3000uax-v1-ubootmod-bl31-uboot.fip FIP
```
4. Set static IP on your PC: `192.168.1.254`, gateway `192.168.1.1`
5. Serve openwrt-mediatek-filogic-cudy_wbr3000uax-v1-ubootmod-initramfs-recovery.itb
using TFTP server.
6. Connect Router LAN with PC LAN.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt initramfs recovery has booted,
clean `/dev/mtd5` ubi partition to utilize maximum of free space & create ubootenvs:
```bash
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
```
4. Perform sysupgrade.
Tested-by: 4pda users
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21225
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
