mirror/openwrt
1
0
Fork 1
mirror of https://git.openwrt.org/openwrt/openwrt.git synced 2026-01-27 21:27:18 +01:00
Code Issues Projects Releases Packages Wiki Activity Actions 6

qualcommax: ipq60xx: add support for TP-Link EAP620HD v3
Some checks are pending
Build Kernel / Build all affected Kernels (push) Waiting to run
Details
Build all core packages / Build all core packages for selected target (push) Waiting to run
Details

Browse source 
Specifications:
  * SoC: Qualcomm IPQ6018/AP-CP03-C1 (64-bit Quad-core Arm Cortex-A53 @ 1.2 GHz)
  * RAM: 2x Zentel A3T4GF40BBF-HP (1 GiB DDR3-1866 (13-13-13))
  * Serial Port: 1v8 TTL 115200n8
  * Wi-Fi: Qualcomm QCN5022 (802.11ax/b/g/n)
  * Wi-Fi: Qualcomm QCN5052 (802.11ac/ax/n)
  * Ethernet: RTL8211FS (10/100/1000BASE-T)
  * Flash: GigaDevice PSR1GA30DT (128 MiB)
  * LEDs: 1x Blue Status (GPIO 35 Active High)
  * Buttons: 1x Reset (GPIO 9 Active Low)
  * FCCID: 2AXJ4EAP620HDV3
  * UART: 4-pin unpopulated header by the J1 footprint

Installation Instructions (Serial+TFTP):
  1. Locate the J1 footprint which contains 4 unpopulated pins
  where starting from the arrow, the pins are TX, RX, VCC and GND
  respectively.
  2. Connect a 1v8 TTL port to the 4 pins. Ensure RX and TX are crossed
     over.
  3. Copy openwrt-qualcommax-ipq60xx-tplink_eap620-hd-v3-initramfs-uImage.itb
  to your TFTP server.
  4. Power up the AP and hold Ctrl+B in the serial console (115200n8) until autoboot is halted.
  5. Run the following commands in the U-boot prompt:
     IPQ6018# setenv serverip <TFTP server addr>
     IPQ6018# setenv ipaddr <addr of the AP>
     IPQ6018# tftpboot 0x44000000 openwrt-qualcommax-ipq60xx-tplink_eap620-hd-v3-initramfs-uImage.itb
     IPQ6018# bootm 0x44000000
     You may need to type Ctrl+C and Enter before running these commands
     to clear invisible characters from the buffer.
  6. Run the following command in a terminal to copy the sysupgrade image
     to be installed (check IP address):
     $ scp -O openwrt-qualcommax-ipq60xx-tplink_eap620-hd-v3-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
  7. Activate the OpenWrt serial console and run the following commands:
     # cd /tmp
     # sysupgrade -n openwrt-qualcommax-ipq60xx-tplink_eap620-hd-v3-squashfs-sysupgrade.bin
  8. The AP will reboot and OpenWrt will be successfully installed.

Installation Instructions (Web UI method):
  1. Set up the device using the vendor's web UI. Navigate to
     Management->SSH and enable the "SSH Login" checkbox. Select "Save".

  2. Connect to the machine via SSH:
     $ ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>

  3. Disable signature verification:
     $ cliclientd stopcs
  4. Rename the "-web-ui-factory" image to something less than 63
     characters, maintaining the ".bin" suffix.

  5. Go to System -> Firmware Update.
     Under "New Firmware File", click "Browse" and select the image.
     Select "Update" and confirm by clicking "OK".

  6. If the update fails, the web UI should show an error message.
     Otherwise, the device should reboot into OpenWrt.

Device support followed from EAP620HD v2 and eap6xx-outdoor for DTS.
Links: openwrt/openwrt#18227

Signed-off-by: John Christoforidis <github@yanny.dev>
Link: https://github.com/openwrt/openwrt/pull/21467
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit is contained in:
John Christoforidis 2026-01-08 22:13:27 +02:00 • committed by Robert Marko
parent 8291fdedad
commit 428bcee2f8
8 changed files with 84 additions and 0 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

1
package/boot/uboot-tools/uboot-envtools/files/qualcommax_ipq60xx
View file

@ -24,6 +24,7 @@ netgear,wax610|\
netgear,wax610y|\
tplink,eap610-outdoor|\
tplink,eap623od-hd-v1|\
tplink,eap620-hd-v3|\
tplink,eap625-outdoor-hd-v1)
ubootenv_add_mtd "0:appsblenv" "0x0" "0x40000" "0x20000"
;;

2
package/firmware/ipq-wifi/Makefile
View file

@ -84,6 +84,7 @@ ALLWIFIBOARDS:= \
tplink_deco-x80-5g \
tplink_eap610-outdoor \
tplink_eap620hd-v1 \
tplink_eap620-hd-v3 \
tplink_eap623-outdoor-hd-v1 \
tplink_eap625-outdoor-hd-v1 \
tplink_eap660hd-v1 \
@ -269,6 +270,7 @@ $(eval $(call generate-ipq-wifi-package,spectrum_sax1v1k,Spectrum SAX1V1K))
$(eval $(call generate-ipq-wifi-package,tplink_deco-x80-5g,TP-Link Deco X80-5G))
$(eval $(call generate-ipq-wifi-package,tplink_eap610-outdoor,TPLink EAP610-Outdoor))
$(eval $(call generate-ipq-wifi-package,tplink_eap620hd-v1,TP-Link EAP620 HD v1))
$(eval $(call generate-ipq-wifi-package,tplink_eap620-hd-v3,TP-Link EAP620 HD v3))
$(eval $(call generate-ipq-wifi-package,tplink_eap623-outdoor-hd-v1,TP-Link EAP623-Outdoor HD v1))
$(eval $(call generate-ipq-wifi-package,tplink_eap625-outdoor-hd-v1,TP-Link EAP625-Outdoor HD v1))
$(eval $(call generate-ipq-wifi-package,tplink_eap660hd-v1,TP-Link EAP660 HD v1))

50
target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6018-eap620-hd-v3.dts Normal file
View file

@ -0,0 +1,50 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "ipq6018-tplink-eap6xx-outdoor.dtsi"
/ {
model = "TP-Link EAP620HD v3";
compatible = "tplink,eap620-hd-v3", "qcom,ipq6018";
/* Delete EAP6xx outdoor leds node to redefine it. */
/delete-node/ leds;
aliases {
led-boot = &led_status_blue;
led-failsafe = &led_status_blue;
led-running = &led_status_blue;
led-upgrade = &led_status_blue;
};
leds {
compatible = "gpio-leds";
led_status_blue: status-blue {
function = LED_FUNCTION_STATUS;
gpios = <&tlmm 35 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_BLUE>;
};
};
};
&mdio {
rtl8211f_4: ethernet-phy@4 {
reg = <4>;
compatible = "ethernet-phy-ieee802.3-c22";
};
};
&tlmm {
gpio-reserved-ranges = <20 1>;
};
&switch {
switch_mac_mode1 = <MAC_MODE_SGMII_PLUS>;
};
&wifi {
qcom,ath11k-calibration-variant = "TP-Link-EAP620-HD-v3";
status = "okay";
};

20
target/linux/qualcommax/image/ipq60xx.mk
View file

@ -251,6 +251,26 @@ define Device/tplink_eap625-outdoor-hd-v1
endef
TARGET_DEVICES += tplink_eap625-outdoor-hd-v1
define Device/tplink_eap620-hd-v3
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := TP-Link
DEVICE_MODEL := EAP620 HD v3
BLOCKSIZE := 128k
PAGESIZE := 2048
SOC := ipq6018
DEVICE_PACKAGES := ipq-wifi-tplink_eap620-hd-v3
IMAGES += web-ui-factory.bin
IMAGE/web-ui-factory.bin := append-ubi | tplink-image-2022
TPLINK_SUPPORT_STRING := SupportList:\r\n \
EAP620 HD(TP-Link|UN|AX1800-D):3.0\r\n \
EAP620 HD(TP-Link|CA|AX1800-D):3.0\r\n \
EAP620 HD(TP-Link|JP|AX1800-D):3.0\r\n \
EAP620 HD(TP-Link|EG|AX1800-D):3.0\r\n
endef
TARGET_DEVICES += tplink_eap620-hd-v3
define Device/yuncore_fap650
$(call Device/FitImage)
$(call Device/UbiFit)

2
target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network
View file

@ -40,6 +40,7 @@ ipq60xx_setup_interfaces()
netgear,wax610y|\
tplink,eap610-outdoor|\
tplink,eap623od-hd-v1|\
tplink,eap620-hd-v3|\
tplink,eap625-outdoor-hd-v1)
ucidef_set_interface_lan "lan" "dhcp"
;;
@ -66,6 +67,7 @@ ipq60xx_setup_macs()
label_mac=$lan_mac
;;
tplink,eap610-outdoor|\
tplink,eap620-hd-v3|\
tplink,eap623od-hd-v1|\
tplink,eap625-outdoor-hd-v1)
label_mac=$(get_mac_binary /tmp/factory_data/default-mac 0)

7
target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
View file

@ -70,6 +70,13 @@ case "$FIRMWARE" in
ath11k_patch_mac $(macaddr_add $label_mac 1) 0
ath11k_set_macflag
;;
tplink,eap620-hd-v3)
caldata_from_file "/tmp/factory_data/radio" 0 0x20000
label_mac=$(get_mac_binary /tmp/factory_data/default-mac 0)
ath11k_patch_mac $label_mac 1
ath11k_patch_mac $(macaddr_add $label_mac 1) 0
ath11k_set_macflag
;;
yuncore,fap650)
caldata_extract "0:art" 0x1000 0x20000
;;

1
target/linux/qualcommax/ipq60xx/base-files/lib/preinit/09_mount_factory_data
View file

@ -8,6 +8,7 @@ preinit_mount_factory_data() {
case $(board_name) in
tplink,eap610-outdoor|\
tplink,eap620-hd-v3|\
tplink,eap623od-hd-v1|\
tplink,eap625-outdoor-hd-v1)
mtd_path=$(find_mtd_chardev "factory_data")

1
target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh
View file

@ -202,6 +202,7 @@ platform_do_upgrade() {
nand_do_upgrade "$1"
;;
tplink,eap610-outdoor|\
tplink,eap620-hd-v3|\
tplink,eap623od-hd-v1|\
tplink,eap625-outdoor-hd-v1)
tplink_do_upgrade "$1"