Hardware specification:
SoC: MediaTek MT7981B
Flash: ESMT F50L1G41LB 128MB
RAM: ESMT M15T2G16128A DDR3 256MB
Ethernet: 3x 1G
Button: Reset, WPS
MAC addresses
LAN: Label MAC (stored in Factory partition offset 0x1fef20)
WAN: LAN + 1
WiFi: LAN
Official LED layout, from left to right:
[power] [internet] [wps] [wifi] [lan3/2/1] [wan]
Redefinition for OpenWrt:
[power]: used for led-boot, led-failsafe, and led-running
[internet]: used for WAN RX/TX indication
[wps]: used for led-upgrade
[wifi] and [lan3/2/1]: unchanged
[wan]: used for WAN link indication
Installing OpenWrt:
- Setup a tftp server on your PC. Copy
xxx-preloader.bin, xxx-bl31-uboot.fip and
xxx-initramfs.itb to tftp root directory.
- Connect to the router via ssh or telnet,
username: useradmin, password is the web
login password of the router.
- Backup all critical flash partitions with
the following commands where x.x.x.x is
the IP of your PC.
IP=x.x.x.x
cd /dev
for d in /sys/class/mtd/mtd?; do
if [ "$(cat $d/name)" = "BL2" ]; then
tftp -l $(basename $d) -r bl2.img -p $IP
elif [ "$(cat $d/name)" = "FIP" ]; then
tftp -l $(basename $d) -r fip.bin -p $IP
elif [ "$(cat $d/name)" = "Factory" ]; then
tftp -l $(basename $d) -r factory.bin -p $IP
fi
done
for d in /sys/devices/virtual/ubi/ubi0/ubi0_*; do
[ "$(cat $d/name)" != "customer" ] && continue
tftp -l $(basename $d) -r customer -p $IP
break
done
- Flash with the following commands:
cd /tmp
tftp -r xxx-preloader.bin -g x.x.x.x
tftp -r xxx-bl31-uboot.fip -g x.x.x.x
mtd write xxx-preloader.bin spi0.0
mtd write xxx-bl31-uboot.fip FIP
mtd erase ubi
- Set a static ip(192.168.1.254) for your PC.
And then reboot the router. It will run
initramfs image automatically.
- After openwrt boots up, perform sysupgrade
via web UI.
Reverting to the vendor firmware:
- Setup a tftp server on your PC with ip
address 192.168.1.254. And make sure
bl2.img, fip.bin, factory.bin and customer
are located in tftp root directory.
- Power off the router.
- Press and hold WPS key, then power on
the router.
- Release WPS key, when internet/wifi/wps
leds are blinking.
- Wait until internet/wifi/wps leds light
up, power off the router.
- Press and hold reset key, power up the
router, release reset key 15s later.
- Connect to http://192.168.1.1, now you
can upload vendor .bin firmware.
Uboot netconsole:
Uboot netconsole can be enabled by WPS
or reset key.
- Setup a linux PC with ip 192.168.1.254.
Open a new terminal and execute
'stty -isig -echo cbreak; nc -lup 6666'
- Press and hold WPS(or reset) key, then
power on the router.
- Release key once internet/wifi/wps leds
are all on.
NOTE: don't hold the key more than 5s
after internet/wifi/wps leds on, or it
will try to revert to vendor firmware.
- 5s later, uboot bootmenu will show on
the terminal.
Signed-off-by: Zhiwei Cao <bfdeh@126.com>
Link: https://github.com/openwrt/openwrt/pull/18631
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Kebidumei AX3000-U22 is one of many clones of the same range extender
that can be found on Aliexpress or other Chinese portals.
The easiest way to identify this model is by searching for "AX3000
Repeater" and picking the device that looks like mine [0].
Specification:
- SoC: MediaTek MT7981B (1.3 GHz)
- RAM: 256 MB
- Flash: 16 MB SPI NOR
- Ports: 1 x 1 GbE
- Antenna: 6 (2 fake)
- WiFi: MediaTek dual-band WiFi 6
- 2.4 GHz: b/g/n/ax, MIMO 2x2
- 5 GHz: a/n/ac/ax, MIMO 2x2
- Buttons: Reset & WPS
- LEDs: Ethernet (green), Status (red, green, blue)
- Power: 110–240 V AC (internal PSU, board uses 12 V DC)
- Serial: unmarked connector on PCB
[1: Vcc, 2: RX, 3: TX, 4: GND]
Install via OEM web UI:
1. Use reset button to perform factory reset.
2. Connect PC to LAN port and obtain DHCP address.
3. Upload the sysupgrade image via OEM firmware upgrade page,
e.g. http://192.168.18.1/upgrade.html
4. After reboot, hold reset button to clear leftover vendor config.
Install via serial:
1. Connect serial console (115200 8N1).
2. Enter the console.
3. Backup mtd4 partition if you want to restore OEM FW later.
4. Download image.
5. Run 'sysupgrade -n'.
Revert to stock:
1. Run sysupgrade without keeping config using mtd4 backup.
[0] https://openwrt.org/_media/media/kebidumei_ax3000-u22.png
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20287
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Keenetic KN-1812/Netcraze NC-1812
Device specification
--------------------
SoC Type: MediaTek MT7988D, Cortex-A73, 64-bit
RAM: 1024MB DDR4 Micron MT40A512M16TB-062E:R
Flash: SPI NAND Winbond W25N02KV (256 MiB)
Ethernet: 4x1GbE (internal MT7988 built-in) + 2.5GbE (internal MT7988 phy) + 10GbE (RTL8261BE)
WLAN: MT7992AV
WLAN 2g: MediaTek MT7975N, b/g/n/ax/be, MIMO 4x4
WLAN 5g: MediaTek MT7977B, a/n/ac/ax/be, MIMO 4x4
LEDs: 5 LEDs, 1 power green, 1 internet green,
2x fn green, 1 wlan green, gpio-controlled
Button: 4 (Reset, WPS, FN1, FN2)
USB port: Yes, 1xUSB3.2 and 1xUSB2.0 (via GL850G)
Power: 12 VDC, 3 A
Notes:
* The device supports dual boot mode
* Fn2 led reassigned to wlan 2.4
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. a) Keenetic
Rename "openwrt-mediatek-filogic-keenetic_kn-1812-squashfs-factory.bin"
to "KN-1812_recovery.bin" and place it in tftp server directory.
b) Netcraze
Rename "openwrt-mediatek-filogic-netcraze_nc-1812-squashfs-factory.bin"
to "NC-1812_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20737
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This AX3000 flying saucer-shaped device is sold under a few names:
- Widelantech WAP430X
http://www.widelantech.com/?m=home&c=View&a=index&aid=131
- Felicomm
- UeeVii UAP200 (sold on amazon.com)
True name, as marked on the PCB and as appears in the DTS, is WAP430X.
Hardware:
- SoC: Mediatek MT7981B
- RAM: 256MiB DDR3
- ROM: 16MiB NOR flash (Winbond 25Q128JVSQ)
- Wired: one GbE RJ45 port
- Wireless: Mediatek MT7976CN DBDC
- Antennas: Internal (two 2.4 GHz 4.5 dBi, three 5 GHz 6 dBi)
- GPIO: two blue LEDs (status, WLAN), one button (reset)
- Power: DC5521 (12V) or 802.3af PoE (48V 0.3A)
- UART: J500 on PCB [3v3] (Rx) (Tx) (Gnd), 115200n
Original firmware is GECOOS 8.0_2024081000, a fork of OpenWrt 21.02
created by Widelantech. All ports are closed except 443 (web management
interface) and 80 (redirects to 443). UART is locked down, but U-Boot
bootloader is friendly.
Installation is done via UART (see note below).
Method 1: press any key during boot to enter MTK U-Boot bootloader,
then choose option 2 (Upgrade firmware) and upload sysupgrade binary
via TFTP (or via Xmodem).
Method 2: put sysupgrade binary on a webserver (http, not https); after
GECOOS loads, choose option 4 (固件在线升级 = online firmware upgrade)
in the menu and enter the URL to the sysupgrade binary.
Note: GECOOS has a slick web management, and firmware can be uploaded
at https://6.6.6.6/#/system/sysupgrade but it's still not clear how to
convert the sysupgrade binary to a factory binary accepted by the web
interface (WIP).
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20402
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ASUS TUF-AX4200Q(TUF 小旋风Pro WiFi6 AX4200) is a home router that adds an additional 2.5G Ethernet port to ASUS TUF-AX4200.
Hardware
- - - - - - - -
- SOC : MediaTek MT7986
- RAM : 512MB DDR3
- FLASH : 256MB SPI-NAND (Winbond W25N02KV)
- WIFI : Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
- ETH : MediaTek MT7531 Switch
MaxLinear GPY211C 2.5 N-Base-T PHY (WAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (LAN)
- UART : 3V3 115200 8N1 (Pinout silkscreened / Do not ocnnect VCC)
Installation
- - - - - - - -
Vendor-UI Method:
1. Download or make the OpenWrt initramfs.trx image
2. Connect the PC via LAN to one of the yellow router ports and wait until your PC to get a DHCP lease.
3. Browse to http://192.168.50.1/
4. If your router is brand new, finish the setup process and log into the Web-UI.
5. Navigate to Administration -> Firmware Upgrade and upload the downloaded OpenWrt image.
6. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using SCP and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
TFTP Method:
1. Download the OpenWrt initramfs image.
Copy the image to a TFTP server reachable at 192.168.1.70/24.
Rename the image to tufax4200q.bin.
2. Connect the PC with TFTP server to the TUF-AX4200Q.
Set a static ip on the ethernet interface of your PC.
(IP address: 192.168.1.70, subnet mask: 255.255.255.0)
Connect to the serial console,
interrupt the autoboot process by pressing '4' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 tufax4200q.bin
$ bootm 0x46000000
4. Wait for OpenWrt to boot.
Transfer the sysupgrade image to the device using SCP and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
(based on support for ASUS RT-AX52 by achterin and trx image generation by remittor)
Signed-off-by: Brian Lee <larte332@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20900
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Upstream is strongly considering removing of_gpio.h. As of this commit,
3 upstream drivers remain with actual usage.
Get ahead of upstream and use the GPIOD API before the OF one goes away.
Rework to remove mediatek,reset-pin in favor of the standard
reset-gpios.
Fix wrong high GPIO.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20088
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The child node "partitions" doesn't have "reg" property. Hence, we
don't need to use "#address-cells" and "#size-cells" to describe the
reg property information.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20942
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The child node "partitions" doesn't have "reg" property. Hence, we
don't need to use "#address-cells" and "#size-cells" to describe the
reg property information.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20942
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Devices package:
Add missing USB3 driver
Device tree:
Fix model name and pwm usage
Add missing supply for I2C and USB
Update network port names based on the shell image [1]
[1] https://docs.banana-pi.org/bpi-r4_lite/banana_pi_bpi-r4_lite_case_1.png
Fixes: 8b6c6978 ("mediatek: add support for BananaPi BPi-R4 Lite")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
There is no reason to limit USB to 2.0 mode by default. This
limitation should be done when both gmac2 and USB are enabled.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Remove I2C, PCIe, PWM, UART and USB from the MT7987A SoC dtsi.
These should not be enabled by default, but rather enabled based
on the device.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
This commit increases the SPI bus frequency from 20 to 52 MHz. Reduces boot
time by 2s. Below is a performance comparison.
Before:
root@OpenWrt:~# dd if=/dev/mtd1 of=/dev/null bs=10M count=1 status=progress
10485760 bytes (10 MB, 10 MiB) copied, 1.68404 s, 6.2 MB/s
After:
root@OpenWrt:~# dd if=/dev/mtd1 of=/dev/null bs=10M count=1 status=progress
10485760 bytes (10 MB, 10 MiB) copied, 0.819222 s, 12.8 MB/s
Taken from PR #18752 as each device should be tested individually, so I have
created a separate PR for this.
Signed-off-by: Sky Huang <SkyLake.Huang@mediatek.com>
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20853
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
SOC: MediaTek MT7981
RAM: 512MB DDR4
FLASH: 128MB SPI-NAND
WIFI: Mediatek MT7915 (integrated) 2x2 802.11ax 2.4 / 5 GHz
ETH: Mediatek MT7981 internal 1 GbE PHY
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect the TFTP server to the EAX17. Conect to the serial console,
interrupt the autoboot process by pressing '0' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ tftpboot openwrt.bin
$ bootm
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Signed-off-by: Jascha Sundaresan <flizarthanon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20354
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Product name: Wavlink WL-WN536AX6 Rev a "Mighty LX2"
Product link: https://www.wavlink.com/en_us/product/WL-WN536AX6.html
Specifications:
SOC: MT7986AV
RAM: 512MB DDR4
Flash: 128MB SPI NAND
Ports: 4 LAN (1G) & 1 WAN (2.5G)
WIFI: MT7976PN + MT7975N
LEDs: 8 (STATUS, WIFI, WAN, LAN1, LAN2, LAN3, LAN4, PWR)
USB: 1 (3.0)
MAC table, same as stock firmware:
LAN: 80:3F:5D:xx:xx:x1 partition "hw" at 0x44e (ASCII)
WAN: 80:3F:5D:xx:xx:x2 partition "hw" at 0x460 (ASCII)
2G: 80:3F:5D:xx:xx:x3
5G: 80:3F:5D:xx:xx:x4
* Installation with OEM WebUI:
Note: Make sure PC is connected on LAN1 port. The OEM firmware has an unknown root password and settings are kept after upgrading firmware. Therefore, a customized Openwrt firmware is needed to remove the root password on login, by adding `passwd -d root` to /etc/init.d/bootcount. The WebUI does a filename check so the customized firmware is named accordingly.
1. Download modified firmware file `WAVLINK_WN536AX6-A_M36AX6_V250320-WO-437baca-modified.bin` from https://github.com/ses1er/firmware-misc/tree/main/wavlink/wl-wn536ax6a
2. Log into WebUI on default IP: http://192.168.20.1
3. Browse to More (top menu) -> System -> Firmware Upgrade.
4. Under `Local Upgrade` section, check the device to be upgraded and upload downloaded modified firmware. Click `UPLOAD FILE`, then `APPLY`
5. Wait about 2 minutes (ignore progress bar), and browse to http://192.168.20.1. You should see LUCI login page. Username is root and no password.
6. Browse to `System -> Backup/Flash Firmware`, click on `Flash Image`, click `Browse` and locate `openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin` file.
7. Uncheck `Keep settings and retain the current configuration` and click `Continue`.
8. Router will now be set to IP 192.168.1.1 which is the Openwrt default.
* Installation with UART:
Note: Having UART connected while cold booting the device will result in a kernel panic when initializing wifi. I've found this workaround:
1. Power off the device and ensure UART is not connected to PC.
2. Power up the device, when lights come on, plug in UART.
3. Warm boots and soft restarts will not cause kernel panic for the duration of device being powered on. Repeat steps for subsequent cold boots.
1. Configure TFTP server with IP 192.168.1.66. Copy `openwrt-mediatek-filogic-wavlink_wl-wn536ax6a-initramfs.itb` to TFTP root.
2. Interrupt boot by pressing 0.
3. Run the following in Uboot console: `setenv serverip 192.168.1.66; setenv ipaddr 192.168.1.1; tftpboot 0x46000000 openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-initramfs.itb; bootm`
4. Transfer `openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin` to device:
(`scp -O openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/`)
5. Run the following on device: `sysupgrade -n /tmp/openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin`
Signed-off-by: Qing W. <ses1er@gmail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/20760
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Replace hardcoded numbers with the dt-bindings drive strength macros
defined in "dt-bindings/pinctrl/mt65xx.h".
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20894
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This board is also as known as LC-HX3001
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: Foresee F35SQA001G 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain SSH access:
Method 1:
1. Connect UART Adapter to the router
2. UART pins are enabled, set the root password with passwd command
start the dropbear instance on port 22
Method 2:
1. Login into web interface, and restore the router with SSH enabled configuration.
2. After reboot Default Web interface password will be 12345678
SSH password is empty
Flash instructions:
1. Connect to HX21, backup everything, especially 'Factory' part.
3. Write new FIP:
mtd write openwrt-mediatek-filogic-hx_21-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
8. To write new BL2
Install mtd-rw
opkg update && opkg install kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd write openwrt-mediatek-filogic-imou_hx21-preloader.bin bl2
Signed-off-by: Jahidul Islam <hello@jahid.io>
Link: https://github.com/openwrt/openwrt/pull/20753
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
According to the factory uboot and firmware[1], the ubi size is set
to 512 MiB (0x20000000) and it exceeds the size of the flash, after
that the uboot and kernel resizes it to 114.5 MiB (0x7280000) instead
of 114.125 MiB (0x7220000). The mismatch of the ubi size causes
kernel fails to read ubi volumes and throws panic.
Trim whitespaces while at it.
1. https://github.com/immortalwrt/immortalwrt/issues/2123#issuecomment-3523744128
Fixes: c908fc7d95 ("mediatek: add support for Zbtlink ZBT-Z8102AX v2")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20769
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3GHz
- RAM : DDR3 256Mbytes, ESMT M15T2G16128A
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976CN dual-band Wi-Fi 6
- 2.4GHz : b/g/n/ax, MU-MIMO
- 5GHz : a/n/ac/ax, MU-MIMO
- Ethernet : MediaTek MT7531AE
- LAN : 10/100/1000 Mbps x4
- WAN : 10/100/1000 Mbps x1
- UART : 1x4 pin header hole on PCB
- 3.3V, RX, GND, TX (115200, 8N1)
- Buttons : WPS, Reset
- LEDs : 1x CPU (Amber/Blue)
1x Wi-Fi (Amber/Blue)
1x WAN activity (Amber/Blue)
4x LAN activity (Amber/Blue)
- Power : 12VDC, 1A (Center positive polarity)
Note: The LED color is amber or blue, depending on your router's color
(black/white).
MAC address
-----------
+-----------+-------------------+-----------+
| Interface | MAC | Algorithm |
+-----------+-------------------+-----------+
| WLAN 2.4G | B0:38:6C:xx:xx:xx | label |
| WLAN 5G | B2:38:6C:4x:xx:xx | |
| WAN | B0:38:6C:xx:xx:xx | label + 1 |
| LAN | B0:38:6C:xx:xx:xx | label + 3 |
+-----------+-------------------+-----------+
The WLAN 2.4G MAC address was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software (ipTIME Firmware Wizard (11ac))
from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router (keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router (LAN port) to the PC
6. Run the OEM recovery software and follow the instructions
7. Select the *squashfs-factory.bin file during the router recovery process
8. Wait for the router to boot from *squashfs-factory.bin
Limitation: Triggering the WLAN LED for activity on both phy0 (2.4GHz) and phy1 (5GHz)
----------
Currently, the UCI doesn't support triggering a single LED for activity
on multiple WLAN interfaces. As a temporary workaround, the LED is
configured to only indicate activity on `phy1`. If you wish to monitor
`phy0` instead, you must change the device from `phy1-ap0` to `phy0-ap0`
in the LuCI LED configuration.
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20771
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ports are physically labelled in reverse order on the device.
This patch aligns logical names with physical ones.
LED order on front of device is correct after this patch.
Fixes: 9d66b8b312
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Link: https://github.com/openwrt/openwrt/pull/20528
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for TP-LINK BE450.
Device specification
--------------------
SoC Type: MediaTek MT7988D, Cortex-A73, 64-bit
RAM: 512MB
Flash: SPI NAND GigaDevice (128 MiB)
Ethernet: MediaTek MT7531AE (3 Ports) + 2.5GbE (internal MT7988 phy) + 10GbE (RTL8261N)
WLAN: MT7992
WLAN 2g: MediaTek MT7975N, b/g/n/ax/be, MIMO 4x4
WLAN 5g: MediaTek MT7979N, a/n/ac/ax/be, MIMO 4x4
LEDs: 8 LEDs, 1 status blue, 2x WIFI blue, 2x Internet
blue/orange, 1 LAN blue, 1 usb blue, 1 wps blue, gpio-controlled
Button: 2 (Reset, WPS)
USB port: Yes
Power: 12 VDC, 2 A
Connector: Barrel
Bootloader: Main U-Boot - U-Boot 2023.10-rc4. Additionally, ubi0
partition contain "seconduboot" (also U-Boot 2023.10-rc4)
Serial console (UART), unpopulated, located near the power connector
---------------------
heatsink
| |
| |
| | +----+-----+------+-------+ +-----------------+
| | | TX | RX | GND | +3.3V | | power connector |
+---+ +----+-----+------+-------+ +-----------------+
|
Don't connect ----+
Disassemble: rm the 2 screws at the bottom and the one at the backside.
un-clip the case starting at the edge above the LEDs.
Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
tftpboot 0x50000000 openwrt-mediatek-filogic-tplink_be450-initramfs-kernel.bin && bootm 0x50000000
4. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Note: the 10GbE (RTL8261N) is only working if reverting this Realtek target specific commit:
b77fa45d12
The second ubi partition (ubi1) is empty and there is no known
dual-partition mechanism, neither in u-boot nor in the stock firmware.
NMBM is not used.
Not Working: WED, if activated, MT7992 isn't recognized any more.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Link: https://github.com/openwrt/openwrt/pull/20398
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit fixes mistaken executable bit on dts files.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20676
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The BPi-R4 Lite is a WiFi-7 router board based on the MT7987 SoC.
Specification :
- SOC: Mediatek MT7987A (4x Cortex-A53
- RAM: 2GB
- Flash: 32MB SPI NOR, 256MB SPI NAND, 8GB eMMC
- Switch: MediaTek MT7531AE
- Ports : 4x LAN (1G), 1x SFP (via MT7531), 1x WAN (2.5G)
- Buttons : Reset & WPS/Mesh
- LEDs : Status (PWM), SFP
- USB: on-board VIA VL817 USB3.1/USB2.0 hub
* 1 - mPCIe B (SIM3)
* 2 - NGFF-KEYB (SIM1)
* 3 - USB-A connector
* 4 - mPCIe A (SIM4)
- mPCIe: 1x 8GT/s x2 or 2x 8GT/s x1 (configurable via bootloader)
- RTC: PCF8563
- mikroBUS socket with SPI, I2C and full UART
- on-board HT42B534 USB-to-serial for Type-C console port
- Power: USB Type-C PD 20V, or DC via barrel connector or JST-VH 3.96
Installation:
Uncompress *sdcard.img.gz and write to microSD card, eg. using 'dd'.
Use bootloader menu on the serial console to install SPI-NAND or SPI-NOR,
once installed to SPI-NAND you can use the bootloader menu to install to
eMMC. See instructions for BananaPi R3 for details.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import and clean DT and DT-overlay files from MediaTek's SDK to build
an image with various DT-overlays for the MT7987 reference board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Since 6b43a52171, the PHY is using interrupts instead of polling. It
turned out that the interrupt number is wrong and the WAN port doesn't
work. This commit fixes this bug.
Fixes: 6b43a52171 ("mediatek: mt7622: add the missing phy interrupt-parent for WAX206")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This board is also as known as E-Life ETR631-T/ETR635-U.
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Uncompress the configuration:
* Enter fakeroot if you are not login as root.
tar -zxf <filename>.tar.gz
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; telnetd; ) &
5. Repack the configuration:
tar -zcf backup.tar.gz etc/
6. Upload new configuration via web interface, now you can connect to
KOMI A31 via telnet.
Flash instructions:
1. Connect to KOMI A31, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-konka_komi-a31-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-konka_komi-a31-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20357
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These devices only have one SPI peripheral. And the chip select pin is
directly controlled by the SPI host hardware. Hence we don't need to
assign empty GPIO phandle for them. This patch also adjust the reg
address of the SPI peripheral node to follow the cs-gpios changes.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19845
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Should be reset-gpio. Also added GPIO_ACTIVE_HIGH for clarity.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20116
Signed-off-by: Robert Marko <robimarko@gmail.com>
The former is deprecated. Fixes dtc warning.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20116
Signed-off-by: Robert Marko <robimarko@gmail.com>
The latter is more descriptive in terms of what's going on.
Mostly found with
git grep gpios\ | grep 0\>
git grep gpios\ | grep 1\>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20116
Signed-off-by: Robert Marko <robimarko@gmail.com>
The former is deprecated. Fixes dtc warning.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20116
Signed-off-by: Robert Marko <robimarko@gmail.com>
Point the driver to the precal section of the emmc "factory" partition.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://github.com/openwrt/openwrt/pull/20154
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Replace the hotplug script with nvmem now that loading data from emmc
partitions is supported.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://github.com/openwrt/openwrt/pull/20154
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Avoids the occacial lost race, where VAPs are created before the hotplug
script has updated the phy mac address.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://github.com/openwrt/openwrt/pull/20154
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add missing bluetooth support btif in dts.
Signed-off-by: Elwin Huang <s09289728096@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20181
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for Buffalo WSR-6000AX8 and AX8P models.
Hardware
--------
SOC: MediaTek MT7986B
RAM: 512MB
FLASH: 128MB SPI-NAND (Winbond)
WIFI 2.4G: (Embedded in SOC) b/g/n/ax, MIMO 4x4
WIFI 5G: (Embedded in SOC) a/n/ac/ax, MIMO 4x4
ETHERNET: 2.5GbE MaxLinear GPY211C (eth1: WAN)
ETHERNET: MediaTek MT7531AE 3xGbE (eth0: LAN1, LAN2, LAN3)
UART: 3.3V 115200 8N1
Serial(UART) Pin Layout
-----------------------
+-------+-------+-------+-------+
J4 | RX | TX | GND |(3.3V) |
+-------+-------+-------+-------+
(Bottom Side)
MAC Address Table
-----------------
lan1-3: board_data 0x4(text)
eth1/WAN: board_data 0x4(text)
WIFI 2.4G: lan1 + 2
WIFI 5G: lan1 + 9
Installation
------------
1. Set up a TFTP server with the IP address "192.168.11.2".
2. Rename the OpenWrt initramfs image to "linux.ubi-recovery" and place it
in the TFTP server's root directory.
3. While holding down the AOSS button, power on the WSR-6000AX8 (or AX8P).
4. The device will automatically download the initramfs image
from the TFTP server and boot into it.
5. Once booted, run "sysupgrade -n" using the OpenWrt sysupgrade image
to complete the installation.
Recovery
--------
1. Decrypt the official firmware image using "buffalo-enc".
example:
$ buffalo-enc -d -i wsr_6000ax8_jp_100 -o wsr_6000ax8_jp_100.dec \
-l -O 0xc8
2. Run "sysupgrade -F -n" with the decrypted image.
Signed-off-by: Shin Sato <shin.sugar.ssyysy2021@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/13107
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification :
- SOC : Mediatek MT7981B (1.3GHz)
- RAM : 256MB
- Flash : 16MB SPI NOR
- Ports : 4 LAN (1G) & 1 WAN (1G)
- WIFI : MediaTek dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Buttons : Reset & WPS/Mesh
- LEDS : WAN (Green), Status (Red & Blue)
- Power : 12V1A
Install via OEM web ui:
Upload the sysupgrade image to firmware upgrade page on OEM web ui
Install via recovery / revert to stock firmware:
1. Unplug from power
2. Download the Sysupgrade (for openwrt installation) or OEM Factory image (for revert to stock firmware)
3. Set your computer ethernet IP to 192.168.1.X, subnet 255.255.255.0 (X=your chosen ip number ranging from 2-254)
4. Press and hold reset button while turn on / plug power adapter to the router. Wait untill ALL LAN green LED turn on, then release the reset button.
5. Plug the LAN cable from your computer into LAN 1 port then open web browser, and type in the address column : 192.168.1.1
6. Upload the sysupgrade / oem factory image
7. Wait until the router finished flashing (the router will reboot)
8. Set ethernet ip to dhcp
9. Open 192.168.1.1 (for openwrt install) / 192.168.0.1 (for OEM firmware)
Signed-off-by: Ari Kurniawan <noobhek@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20035
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
SoC: Mediatek MT7981BA
RAM: 512 MB DDR4 RAM
Flash: Winbond W25N01GV 128 MB SPI-NAND (dual boot on OEM)
WiFi: MT7976CN DBDC AX
Switch: MediaTek MT7531AE (3x LAN Gigabit ports) + Internal Gbe Phy (1x WAN Gigabit port)
GPIO: 4x LED (power, internet, fn, wifi), 2x buttons (wps, reset), 1x switch (mesh)
UART Interface:
Pins: VCC, TX, RX, NC, GND
Settings: 115200, 8N1
Flashing via TFTP:
1. Connect your PC and router to the first LAN port, configure PC interface using IP 192.168.1.2, mask 255.255.255.0
2. Save the factory image of the OpenWRT firmware, renamed to KN-3711_recovery.bin, on the TFTP server
3. Hold the reset button and power up the device
4. Keep the button pressed until the status LED starts blinking
Signed-off-by: Vladimir Epifantsev <volatilefield@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19633
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This change fixes the eeprom load failure while on boot
Signed-off-by: Rhnn Hur <hurrhnn@icmp.kr>
Link: https://github.com/openwrt/openwrt/pull/20044
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification
-------------
- SoC : MediaTek MT7986AV quad-core ARM Cortex-A53 2GHz
- RAM : DDR4 512Mbytes, Nanya Technology NT5AD256M16E4
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976DAN, MediaTek MT7916AN, MediaTek MT7976AN
- 2.4GHz : b/g/n/ax, Multi User MIMO
- 5GHz : a/n/ac/ax, Multi User MIMO
- 6GHz : ax, Multi User MIMO
- Ethernet : 10/100/1000 Mbps x4, LAN (MediaTek MT7531AE)
10/100/1000/2500 Mbps x1, WAN (MaxLinear GPY211C0VC)
- UART : 1x4 pin header on PCB
- [J1] 3.3V, TX, RX, GND (115200, 8N1)
- Buttons : WPS, Reset
- Switches : Rfkill Slide Switch
- USB : 1x USB 3.0 (MediaTek MT7986AV peripheral)
- FAN : 1x Fan (off - slow - fast)
- LEDs : 1x Power (Blue)
1x CPU (Blue)
1x Wi-Fi 6GHz (Blue)
1x Wi-Fi 5GHz (Blue)
1x Wi-Fi 2.4GHz (Blue)
4x LAN activity (Blue)
1x WAN activity (Blue)
1x USB 3.0 (Blue)
- Power : 12VDC, 3.5A (Center positive polarity)
MAC address
-----------
+-----------+-------------------+------------------------+
| Interface | MAC | Algorithm |
+-----------+-------------------+------------------------+
| WLAN 2.4G | 58:86:94:xx:xx:xx | label1 |
| WLAN 5G | 5A:86:94:xx:xx:xx | label2 with LA Bit set |
| WLAN 6G | 5A:86:94:xx:xx:xx | label1 with LA Bit set |
| WAN | 58:86:94:xx:xx:xx | label1 + 1 |
| LAN | 58:86:94:xx:xx:xx | label1 + 3 |
+-----------+-------------------+------------------------+
The WLAN 2.4G MAC address (label1) was found in 'Factory' partition, 0xA0004
The WLAN 5G MAC address (label2) was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software (ipTIME Firmware Wizard (11ac))
from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router (keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router (LAN port) to the PC
6. Run the OEM recovery software and follow the instructions
7. Select the *squashfs-factory.bin file during the router recovery process
8. Wait for the router to boot from *squashfs-factory.bin
Note: The router will automatically reboot if no file is uploaded within
55 seconds.
Fan Control
------------
The fan speed is controlled by writing a value from 0 to 2 to the
`fan1_target` file.
```
cd /sys/devices/platform/gpio-fan/hwmon/hwmon2
echo '0' > fan1_target // off
echo '1' > fan1_target // slow
echo '2' > fan1_target // fast
```
Limitation: Enabling Wi-Fi 6E
----------
Wi-Fi 6E (6GHz) does not work out of the box on LuCI.
After installation, you need to configure a few settings in the `radio1`
and `default_radio1` sections of the `/etc/config/wireless`.
Once you have made these changes, you can enable and use Wi-Fi 6E.
In the `radio1` section, you need to add three common options:
- band: must be set to `6g`
- country: a valid country code for the 6GHz band
- channel: a preferrend scanning channel (PSC) for 6GHz
In the `default_radio1` section, you need to add the SSID and key:
- ssid: The public name of your Wi-Fi network
- key: The Wi-Fi password
- encryption: must be set to either `sae` for WPA3 or `owe` for OWE
(open network)
Example:
```
config wifi-device 'radio1'
...
option band '6g'
option country 'KR'
option channel '37'
...
config wifi-iface 'default_radio1'
...
option ssid 'my_wifi_6e_name'
option key 'my_strong_password1234'
option encryption 'sae'
...
```
Note: A list of all the 6GHz PSC channels:
```
5, 21, 37, 53, 69, 85, 101, 117, 133, 149, 165, 181, 197, 213, and 229
```
Limitation: Maximum Transmit Power
----------
The maximum transmit power is currently broken. In the drop-down menu,
you can only choose between "driver default" and "255 dBm (2147493647
mW)". There is currently no workaround for the issue. Please leave the
maximum transmit power set to "driver default".
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19763
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add labels wan and cpu for ethernet ports.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19968
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
