mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2026-02-09 20:32:50 +01:00
mediatek: filogic: add support for TP-LINK BE450
This commit adds support for TP-LINK BE450.
Device specification
--------------------
SoC Type: MediaTek MT7988D, Cortex-A73, 64-bit
RAM: 512MB
Flash: SPI NAND GigaDevice (128 MiB)
Ethernet: MediaTek MT7531AE (3 Ports) + 2.5GbE (internal MT7988 phy) + 10GbE (RTL8261N)
WLAN: MT7992
WLAN 2g: MediaTek MT7975N, b/g/n/ax/be, MIMO 4x4
WLAN 5g: MediaTek MT7979N, a/n/ac/ax/be, MIMO 4x4
LEDs: 8 LEDs, 1 status blue, 2x WIFI blue, 2x Internet
blue/orange, 1 LAN blue, 1 usb blue, 1 wps blue, gpio-controlled
Button: 2 (Reset, WPS)
USB port: Yes
Power: 12 VDC, 2 A
Connector: Barrel
Bootloader: Main U-Boot - U-Boot 2023.10-rc4. Additionally, ubi0
partition contain "seconduboot" (also U-Boot 2023.10-rc4)
Serial console (UART), unpopulated, located near the power connector
---------------------
heatsink
| |
| |
| | +----+-----+------+-------+ +-----------------+
| | | TX | RX | GND | +3.3V | | power connector |
+---+ +----+-----+------+-------+ +-----------------+
|
Don't connect ----+
Disassemble: rm the 2 screws at the bottom and the one at the backside.
un-clip the case starting at the edge above the LEDs.
Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
tftpboot 0x50000000 openwrt-mediatek-filogic-tplink_be450-initramfs-kernel.bin && bootm 0x50000000
4. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Note: the 10GbE (RTL8261N) is only working if reverting this Realtek target specific commit:
b77fa45d12
The second ubi partition (ubi1) is empty and there is no known
dual-partition mechanism, neither in u-boot nor in the stock firmware.
NMBM is not used.
Not Working: WED, if activated, MT7992 isn't recognized any more.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Link: https://github.com/openwrt/openwrt/pull/20398
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit is contained in:
Dirk Buchwalder
Hauke Mehrtens
parent
5212866508
commit
71ebc54d2a
10 changed files with 450 additions and 1 deletions
|
|
@ -127,7 +127,8 @@ smartrg,sdg-8733a|\
|
|||
smartrg,sdg-8734)
|
||||
ubootenv_add_mmc "u-boot-env" "mmcblk0" "0x0" "0x8000" "0x8000"
|
||||
;;
|
||||
tplink,archer-ax80-v1)
|
||||
tplink,archer-ax80-v1|\
|
||||
tplink,be450)
|
||||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000" "8"
|
||||
;;
|
||||
ubnt,unifi-6-plus)
|
||||
|
|
|
|||
409
target/linux/mediatek/dts/mt7988d-tplink-be450.dts
Normal file
409
target/linux/mediatek/dts/mt7988d-tplink-be450.dts
Normal file
|
|
@ -0,0 +1,409 @@
|
|||
// SPDX-License-Identifier: (GPL-2.0 OR MIT)
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "mt7988a.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
#include <dt-bindings/pinctrl/mt65xx.h>
|
||||
#include <dt-bindings/regulator/richtek,rt5190a-regulator.h>
|
||||
|
||||
/ {
|
||||
model = "TP-Link BE450";
|
||||
compatible = "tplink,be450", "mediatek,mt7988d";
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
aliases {
|
||||
serial0 = &serial0;
|
||||
label-mac-device = &gmac0;
|
||||
led-boot = &led_status;
|
||||
led-failsafe = &led_status;
|
||||
led-running = &led_status;
|
||||
led-upgrade = &led_status;
|
||||
};
|
||||
|
||||
memory@40000000 {
|
||||
reg = <0x0 0x40000000 0x0 0x40000000>;
|
||||
device_type = "memory";
|
||||
};
|
||||
|
||||
cpus {
|
||||
/delete-node/ cpu@3;
|
||||
};
|
||||
|
||||
reg_1p8v: regulator-1p8v {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "fixed-1.8V";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
reg_3p3v: regulator-3p3v {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "fixed-3.3V";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&button_pins>;
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&pio 13 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&pio 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led-0 {
|
||||
gpios = <&pio 21 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_ORANGE>;
|
||||
function = LED_FUNCTION_WAN;
|
||||
};
|
||||
|
||||
led-1 {
|
||||
gpios = <&pio 28 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_WLAN_5GHZ;
|
||||
};
|
||||
|
||||
led-2 {
|
||||
gpios = <&pio 29 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_WLAN_2GHZ;
|
||||
};
|
||||
|
||||
led_status: led-3 {
|
||||
gpios = <&pio 30 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_STATUS;
|
||||
panic-indicator;
|
||||
};
|
||||
|
||||
led-4 {
|
||||
gpios = <&pio 31 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_LAN;
|
||||
};
|
||||
|
||||
led-5 {
|
||||
gpios = <&pio 35 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_WPS;
|
||||
};
|
||||
|
||||
led-6 {
|
||||
gpios = <&pio 57 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_WAN;
|
||||
};
|
||||
|
||||
led-7 {
|
||||
gpios = <&pio 68 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_USB;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&cpu0 {
|
||||
proc-supply = <&rt5190_buck3>;
|
||||
};
|
||||
|
||||
&cpu1 {
|
||||
proc-supply = <&rt5190_buck3>;
|
||||
};
|
||||
|
||||
&cpu2 {
|
||||
proc-supply = <&rt5190_buck3>;
|
||||
};
|
||||
|
||||
&cci {
|
||||
proc-supply = <&rt5190_buck3>;
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi0_flash_pins>;
|
||||
status = "okay";
|
||||
|
||||
spi_nand: spi_nand@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "spi-nand";
|
||||
|
||||
reg = <0>;
|
||||
|
||||
spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
|
||||
spi-cal-addrlen = <5>;
|
||||
spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>;
|
||||
spi-cal-datalen = <7>;
|
||||
spi-cal-enable;
|
||||
spi-cal-mode = "read-data";
|
||||
|
||||
spi-max-frequency = <52000000>;
|
||||
spi-rx-bus-width = <4>;
|
||||
spi-tx-bus-width = <4>;
|
||||
|
||||
partitions: partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "boot";
|
||||
reg = <0x0 0x200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x200000 0x100000>;
|
||||
};
|
||||
|
||||
partition@300000 {
|
||||
label = "ubi0";
|
||||
reg = <0x300000 0x3200000>;
|
||||
};
|
||||
|
||||
partition@3500000 {
|
||||
label = "ubi1";
|
||||
reg = <0x3500000 0x3200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@6700000 {
|
||||
label = "userconfig";
|
||||
reg = <0x6700000 0x800000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@6f00000 {
|
||||
label = "tp_data";
|
||||
reg = <0x6f00000 0x800000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&mdio0_pins>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
phy-mode = "internal";
|
||||
phy-connection-type = "internal";
|
||||
phy = <&int_2p5g_phy>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac2 {
|
||||
phy-mode = "usxgmii";
|
||||
phy-connection-type = "usxgmii";
|
||||
phy = <&phy0>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gsw_phy3 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&mdio_bus {
|
||||
phy0: ethernet-phy@0 {
|
||||
/* RTL8261N */
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
reg = <0>;
|
||||
|
||||
reset-gpios = <&pio 3 GPIO_ACTIVE_LOW>;
|
||||
reset-assert-us = <100000>;
|
||||
reset-deassert-us = <100000>;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c0_pins>;
|
||||
status = "okay";
|
||||
|
||||
rt5190a_64: rt5190a@64 {
|
||||
compatible = "richtek,rt5190a";
|
||||
reg = <0x64>;
|
||||
/*interrupts-extended = <&gpio26 0 IRQ_TYPE_LEVEL_LOW>;*/
|
||||
vin2-supply = <&rt5190_buck1>;
|
||||
vin3-supply = <&rt5190_buck1>;
|
||||
vin4-supply = <&rt5190_buck1>;
|
||||
|
||||
regulators {
|
||||
rt5190_buck1: buck1 {
|
||||
regulator-name = "rt5190a-buck1";
|
||||
regulator-min-microvolt = <5090000>;
|
||||
regulator-max-microvolt = <5090000>;
|
||||
regulator-allowed-modes =
|
||||
<RT5190A_OPMODE_AUTO RT5190A_OPMODE_FPWM>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
buck2 {
|
||||
regulator-name = "vcore";
|
||||
regulator-min-microvolt = <600000>;
|
||||
regulator-max-microvolt = <1400000>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
rt5190_buck3: buck3 {
|
||||
regulator-name = "vproc";
|
||||
regulator-min-microvolt = <600000>;
|
||||
regulator-max-microvolt = <1400000>;
|
||||
regulator-boot-on;
|
||||
};
|
||||
|
||||
buck4 {
|
||||
regulator-name = "rt5190a-buck4";
|
||||
regulator-min-microvolt = <850000>;
|
||||
regulator-max-microvolt = <850000>;
|
||||
regulator-allowed-modes =
|
||||
<RT5190A_OPMODE_AUTO RT5190A_OPMODE_FPWM>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
ldo {
|
||||
regulator-name = "rt5190a-ldo";
|
||||
regulator-min-microvolt = <1200000>;
|
||||
regulator-max-microvolt = <1200000>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pcie0_1_pins>;
|
||||
reset-gpios = <&pio 7 GPIO_ACTIVE_LOW>;
|
||||
status = "okay";
|
||||
|
||||
pcie@0,0 {
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
|
||||
mt7996@0,0 {
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pio {
|
||||
button_pins: button-pins {
|
||||
pins = "GPIO_RESET", "GPIO_WPS";
|
||||
bias-disable; /* bias-disable */
|
||||
};
|
||||
|
||||
mdio0_pins: mdio0-pins {
|
||||
mux {
|
||||
function = "eth";
|
||||
groups = "mdc_mdio0";
|
||||
};
|
||||
|
||||
conf {
|
||||
groups = "mdc_mdio0";
|
||||
drive-strength = <MTK_DRIVE_8mA>;
|
||||
};
|
||||
};
|
||||
|
||||
i2c0_pins: i2c0-pins-g0 {
|
||||
mux {
|
||||
function = "i2c";
|
||||
groups = "i2c0_1";
|
||||
};
|
||||
};
|
||||
|
||||
pcie0_1_pins: pcie0-pins-g1 {
|
||||
mux {
|
||||
function = "pcie";
|
||||
groups = "pcie_2l_0_pereset", "pcie_clk_req_n0_0";
|
||||
};
|
||||
};
|
||||
|
||||
spi0_flash_pins: spi0-pins {
|
||||
mux {
|
||||
function = "spi";
|
||||
groups = "spi0", "spi0_wp_hold";
|
||||
};
|
||||
};
|
||||
|
||||
enable-usb-power {
|
||||
gpio-hog;
|
||||
gpios = <32 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "USB power";
|
||||
};
|
||||
};
|
||||
|
||||
&ssusb1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&switch {
|
||||
status = "okay";
|
||||
|
||||
ports {
|
||||
port@0 {
|
||||
label = "lan3";
|
||||
};
|
||||
|
||||
port@1 {
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
port@2 {
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
port@3 {
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tphy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&serial0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
|
@ -214,6 +214,11 @@ teltonika,rutc50)
|
|||
totolink,x6000r)
|
||||
ucidef_set_led_netdev "wan" "wan" "green:wan" "wan" "link tx rx"
|
||||
;;
|
||||
tplink,be450)
|
||||
ucidef_set_led_netdev "br-lan" "lan" "blue:lan" "br-lan" "link tx rx"
|
||||
ucidef_set_led_netdev "wlan2g" "WLAN2G" "blue:wlan-2ghz" "phy0.0-ap0"
|
||||
ucidef_set_led_netdev "wlan5g" "WLAN5G" "blue:wlan-5ghz" "phy0.1-ap0"
|
||||
;;
|
||||
tplink,fr365-v1)
|
||||
ucidef_set_led_netdev "port2-green-act" "port-2" "green:port2_act" "port2" "link tx rx"
|
||||
ucidef_set_led_netdev "port1-green-act" "port-1" "green:sfp" "port1" "link tx rx"
|
||||
|
|
|
|||
|
|
@ -159,6 +159,9 @@ mediatek_setup_interfaces()
|
|||
tplink,archer-ax80-v1)
|
||||
ucidef_set_interfaces_lan_wan "lan0 lan1 lan2 lan3" eth1
|
||||
;;
|
||||
tplink,be450)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 eth2" eth1
|
||||
;;
|
||||
tplink,re6000xd)
|
||||
ucidef_set_interface_lan "lan1 lan2 eth1"
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -35,6 +35,14 @@ case "$FIRMWARE" in
|
|||
;;
|
||||
esac
|
||||
;;
|
||||
"mediatek/mt7996/mt7992_eeprom.bin")
|
||||
case "$board" in
|
||||
tplink,be450)
|
||||
ln -sf /tmp/tp_data/MT7992_EEPROM.bin \
|
||||
/lib/firmware/$FIRMWARE
|
||||
;;
|
||||
esac
|
||||
;;
|
||||
*)
|
||||
exit 1
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -156,6 +156,7 @@ case "$board" in
|
|||
;;
|
||||
mercusys,mr90x-v1|\
|
||||
tplink,archer-ax80-v1|\
|
||||
tplink,be450|\
|
||||
tplink,re6000xd)
|
||||
addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0)
|
||||
[ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress
|
||||
|
|
|
|||
|
|
@ -16,6 +16,7 @@ preinit_mount_cfg_part() {
|
|||
mercusys,mr80x-v3|\
|
||||
mercusys,mr90x-v1|\
|
||||
tplink,archer-ax80-v1|\
|
||||
tplink,be450|\
|
||||
tplink,re6000xd)
|
||||
mount_ubi_part "tp_data" "tp_data"
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -43,6 +43,11 @@ preinit_set_mac_address() {
|
|||
addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0)
|
||||
ip link set dev eth1 address "$(macaddr_add $addr 1)"
|
||||
;;
|
||||
tplink,be450)
|
||||
addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0)
|
||||
ip link set dev eth1 address "$(macaddr_add $addr 1)"
|
||||
ip link set dev eth2 address "$(macaddr_add $addr 2)"
|
||||
;;
|
||||
tplink,fr365-v1)
|
||||
lan_mac=$(strings /dev/mtd11 | grep 'option macaddr' | awk -F"'" '{print $2}')
|
||||
wan_mac="$(macaddr_add $lan_mac 1)"
|
||||
|
|
|
|||
|
|
@ -182,6 +182,7 @@ platform_do_upgrade() {
|
|||
mercusys,mr80x-v3|\
|
||||
mercusys,mr90x-v1|\
|
||||
tplink,archer-ax80-v1|\
|
||||
tplink,be450|\
|
||||
tplink,re6000xd)
|
||||
CI_UBIPART="ubi0"
|
||||
nand_do_upgrade "$1"
|
||||
|
|
|
|||
|
|
@ -2234,6 +2234,21 @@ define Device/tplink_archer-ax80-v1
|
|||
endef
|
||||
TARGET_DEVICES += tplink_archer-ax80-v1
|
||||
|
||||
define Device/tplink_be450
|
||||
DEVICE_VENDOR := TP-Link
|
||||
DEVICE_MODEL := BE450
|
||||
DEVICE_DTS := mt7988d-tplink-be450
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
DEVICE_PACKAGES := kmod-mt7992-firmware kmod-usb3 \
|
||||
mt7988-2p5g-phy-firmware mt7988-wo-firmware
|
||||
UBINIZE_OPTS := -E 5
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGE_SIZE := 51200k
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += tplink_be450
|
||||
|
||||
define Device/tplink_re6000xd
|
||||
DEVICE_VENDOR := TP-Link
|
||||
DEVICE_MODEL := RE6000XD
|
||||
|
|
|
|||
Loading…
Add table
Reference in a new issue