mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2026-01-28 03:37:17 +01:00
mediatek: add support for COMFAST CF-WR632AX
COMFAST CF-WR632AX is a compact/travel (123.4 mm * 88.7 mm * 34 mm) wireless WiFi 6 router. Specification ------------- - SoC : MediaTek MT7981B dual-core ARM Cortex-A53 1.3 GHz - RAM : DDR3 512 MiB - Flash : SPI-NAND 128 MiB (Winbond) - WLAN : MediaTek MT7976CN dual-band WiFi 6 - 2.4 GHz : b/g/n/ax, MU-MIMO (2x 5 dBi antennas) - 5 GHz : a/n/ac/ax, MU-MIMO (2x 5 dBi antennas) - Ethernet : - LAN x1 : 10/100/1000 Mbps (MT7981 internal PHY) - WAN x1 : 10/100/1000/2500 Mbps (Maxlinear GPY211C) - USB x1 : 3.0 - UART : through-hole on PCB - assignment : (RX), (TX), (GND), [VCC] - settings : 115200n8 - Buttons x1 : Reset - LEDs x3 : Status (Blue, Green, Red) - Fan x1 : PWM, 4-wire, 5 V, 0.3 A, 45 mm * 10 mm - Power : 5 VDC, 3 A, Type-C Flash instructions ------------------ WebUI Method: 1. Install the *squashfs-sysupgrade.bin image using the stock WebUI update page. 2. Press and hold the reset button after reboot to wipe the stock config. SSH Method: 1. Import stock firmware settings from backup file github.com/andros-ua/owrt-misc/blob/main/cf-wr632ax/backup.file Note: WebUI password will be reset to admin1234 after import. 2. Connect via SSH using root:openwrt credentials. 3. Upload the *squashfs-sysupgrade.bin image. 4. Use the command: sysupgrade -n All checks should pass. Return to stock --------------- Flash a stock firmware using the OpenWrt sysupgrade method. Recovery -------- Power on the router while holding the Reset button until the LED flashes 5 times. The U-Boot Flash WebUI will be available at http://192.168.1.1 or Connect UART and use the U-Boot menu to flash the firmware image or boot an OpenWrt initramfs image. OpenWrt U-Boot flash instructions --------------------------------- 1. Flash ordinary OpenWrt image. 2. Login into the device and backup everything, especially 'Factory' part. 3. Unlock mtd partitions: apk add kmod-mtd-rw insmod mtd-rw i_want_a_brick=1 4. Write new BL2 and FIP: mtd write openwrt-mediatek-filogic-comfast_cf-wr632ax-ubootmod-preloader.bin BL2 mtd write openwrt-mediatek-filogic-comfast_cf-wr632ax-ubootmod-bl31-uboot.fip FIP 5. Set static IP on your PC: ip 192.168.1.254 mask 255.255.255.0 6. Serve OpenWrt initramfs image using TFTP server. 7. Reboot device, wait for TFTP recovery to complete. 8. After OpenWrt has booted, perform sysupgrade. MAC Addresses: ---------------------------------------------------------- | Interface | MAC | Source | ---------------|-------------------|---------------------- | WAN (label) | 40:A5:EF:xx:xx:xx | Factory, 0xe000 | | LAN | 40:A5:EF:xx:xx:xx | Factory, 0xe000 + 1 | | WLAN 2.4 GHz | 40:A5:EF:xx:xx:xx | Factory, 0x4 | | WLAN 5 GHz | 40:A5:EF:xx:xx:xx | Factory, 0x8000 | ---------------------------------------------------------- Signed-off-by: Andrii Kuiukoff <andros.ua@gmail.com> Link: https://github.com/openwrt/openwrt/pull/20382 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit is contained in:
Andrii Kuiukoff
Hauke Mehrtens
parent
8fb644e9e8
commit
b33df7ba33
9 changed files with 674 additions and 0 deletions
|
|
@ -291,6 +291,18 @@ define U-Boot/mt7981_cmcc_rax3000m-nand-ddr4
|
|||
DEPENDS:=+trusted-firmware-a-mt7981-spim-nand-ddr4
|
||||
endef
|
||||
|
||||
define U-Boot/mt7981_comfast_cf-wr632ax
|
||||
NAME:=COMFAST CF-WR632AX
|
||||
BUILD_SUBTARGET:=filogic
|
||||
BUILD_DEVICES:=comfast_cf-wr632ax-ubootmod
|
||||
UBOOT_CONFIG:=mt7981_comfast_cf-wr632ax
|
||||
UBOOT_IMAGE:=u-boot.fip
|
||||
BL2_BOOTDEV:=spim-nand
|
||||
BL2_SOC:=mt7981
|
||||
BL2_DDRTYPE:=ddr3
|
||||
DEPENDS:=+trusted-firmware-a-mt7981-spim-nand-ddr3
|
||||
endef
|
||||
|
||||
define U-Boot/mt7981_cudy_tr3000-v1
|
||||
NAME:=Cudy TR3000 v1
|
||||
BUILD_SUBTARGET:=filogic
|
||||
|
|
@ -1053,6 +1065,7 @@ UBOOT_TARGETS := \
|
|||
mt7981_cmcc_rax3000m-emmc-ddr4 \
|
||||
mt7981_cmcc_rax3000m-nand-ddr3 \
|
||||
mt7981_cmcc_rax3000m-nand-ddr4 \
|
||||
mt7981_comfast_cf-wr632ax \
|
||||
mt7981_cudy_tr3000-v1 \
|
||||
mt7981_gatonetworks_gdsp \
|
||||
mt7981_glinet_gl-mt2500 \
|
||||
|
|
|
|||
|
|
@ -0,0 +1,323 @@
|
|||
--- /dev/null
|
||||
+++ b/arch/arm/dts/mt7981-comfast-cf-wr632ax.dts
|
||||
@@ -0,0 +1,153 @@
|
||||
+// SPDX-License-Identifier: GPL-2.0-or-later
|
||||
+
|
||||
+/dts-v1/;
|
||||
+#include "mt7981.dtsi"
|
||||
+#include <dt-bindings/gpio/gpio.h>
|
||||
+#include <dt-bindings/input/linux-event-codes.h>
|
||||
+
|
||||
+/ {
|
||||
+ #address-cells = <1>;
|
||||
+ #size-cells = <1>;
|
||||
+ model = "COMFAST CF-WR632AX";
|
||||
+ compatible = "mediatek,mt7981", "mediatek,mt7981-rfb";
|
||||
+
|
||||
+ chosen {
|
||||
+ stdout-path = &uart0;
|
||||
+ tick-timer = &timer0;
|
||||
+ };
|
||||
+
|
||||
+ memory@40000000 {
|
||||
+ device_type = "memory";
|
||||
+ reg = <0x40000000 0x20000000>;
|
||||
+ };
|
||||
+
|
||||
+ gpio-keys {
|
||||
+ compatible = "gpio-keys";
|
||||
+
|
||||
+ button-reset {
|
||||
+ label = "reset";
|
||||
+ linux,code = <KEY_RESTART>;
|
||||
+ gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ gpio-leds {
|
||||
+ compatible = "gpio-leds";
|
||||
+
|
||||
+ led_status_blue: led-0 {
|
||||
+ label = "blue:status";
|
||||
+ gpios = <&pio 8 GPIO_ACTIVE_LOW>;
|
||||
+ default-state = "off";
|
||||
+ };
|
||||
+
|
||||
+ led_status_green: led-1 {
|
||||
+ label = "green:status";
|
||||
+ gpios = <&pio 35 GPIO_ACTIVE_LOW>;
|
||||
+ default-state = "off";
|
||||
+ };
|
||||
+
|
||||
+ led_status_red: led-2 {
|
||||
+ label = "red:status";
|
||||
+ gpios = <&pio 34 GPIO_ACTIVE_LOW>;
|
||||
+ default-state = "on";
|
||||
+ };
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
+ð {
|
||||
+ status = "okay";
|
||||
+ mediatek,gmac-id = <1>;
|
||||
+ phy-mode = "gmii";
|
||||
+ phy-handle = <&phy0>;
|
||||
+
|
||||
+ mdio {
|
||||
+ phy0: ethernet-phy@0 {
|
||||
+ compatible = "ethernet-phy-id03a2.9461";
|
||||
+ reg = <0x0>;
|
||||
+ phy-mode = "gmii";
|
||||
+ };
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
+&pio {
|
||||
+ spi_flash_pins: spi0-pins-func-1 {
|
||||
+ mux {
|
||||
+ function = "flash";
|
||||
+ groups = "spi0", "spi0_wp_hold";
|
||||
+ };
|
||||
+
|
||||
+ conf-pu {
|
||||
+ pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
|
||||
+ drive-strength = <MTK_DRIVE_4mA>;
|
||||
+ bias-pull-up = <MTK_PUPD_SET_R1R0_00>;
|
||||
+ };
|
||||
+
|
||||
+ conf-pd {
|
||||
+ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
|
||||
+ drive-strength = <MTK_DRIVE_4mA>;
|
||||
+ bias-pull-down = <MTK_PUPD_SET_R1R0_00>;
|
||||
+ };
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
+&spi0 {
|
||||
+ #address-cells = <1>;
|
||||
+ #size-cells = <0>;
|
||||
+ pinctrl-names = "default";
|
||||
+ pinctrl-0 = <&spi_flash_pins>;
|
||||
+ status = "okay";
|
||||
+ must_tx;
|
||||
+ enhance_timing;
|
||||
+ dma_ext;
|
||||
+ ipm_design;
|
||||
+ support_quad;
|
||||
+ tick_dly = <2>;
|
||||
+ sample_sel = <0>;
|
||||
+
|
||||
+ spi_nand@0 {
|
||||
+ compatible = "spi-nand";
|
||||
+ reg = <0>;
|
||||
+ spi-max-frequency = <52000000>;
|
||||
+
|
||||
+ partitions {
|
||||
+ compatible = "fixed-partitions";
|
||||
+ #address-cells = <1>;
|
||||
+ #size-cells = <1>;
|
||||
+
|
||||
+ partition@0 {
|
||||
+ label = "bl2";
|
||||
+ reg = <0x0 0x100000>;
|
||||
+ };
|
||||
+
|
||||
+ partition@100000 {
|
||||
+ label = "u-boot-env";
|
||||
+ reg = <0x100000 0x80000>;
|
||||
+ };
|
||||
+
|
||||
+ partition@180000 {
|
||||
+ label = "factory";
|
||||
+ reg = <0x180000 0x200000>;
|
||||
+ };
|
||||
+
|
||||
+ partition@380000 {
|
||||
+ label = "fip";
|
||||
+ reg = <0x380000 0x200000>;
|
||||
+ };
|
||||
+
|
||||
+ partition@580000 {
|
||||
+ label = "ubi";
|
||||
+ reg = <0x580000 0x7a80000>;
|
||||
+ compatible = "linux,ubi";
|
||||
+ };
|
||||
+ };
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
+&uart0 {
|
||||
+ mediatek,force-highspeed;
|
||||
+ status = "okay";
|
||||
+};
|
||||
+
|
||||
+&watchdog {
|
||||
+ status = "disabled";
|
||||
+};
|
||||
--- /dev/null
|
||||
+++ b/configs/mt7981_comfast_cf-wr632ax_defconfig
|
||||
@@ -0,0 +1,107 @@
|
||||
+CONFIG_ARM=y
|
||||
+CONFIG_SYS_HAS_NONCACHED_MEMORY=y
|
||||
+CONFIG_POSITION_INDEPENDENT=y
|
||||
+CONFIG_ARCH_MEDIATEK=y
|
||||
+CONFIG_TEXT_BASE=0x41e00000
|
||||
+CONFIG_SYS_MALLOC_F_LEN=0x4000
|
||||
+CONFIG_NR_DRAM_BANKS=1
|
||||
+CONFIG_DEFAULT_DEVICE_TREE="mt7981-comfast-cf-wr632ax"
|
||||
+CONFIG_OF_LIBFDT_OVERLAY=y
|
||||
+CONFIG_TARGET_MT7981=y
|
||||
+CONFIG_SYS_LOAD_ADDR=0x46000000
|
||||
+CONFIG_PRE_CON_BUF_ADDR=0x4007EF00
|
||||
+CONFIG_DEBUG_UART_BASE=0x11002000
|
||||
+CONFIG_DEBUG_UART_CLOCK=40000000
|
||||
+CONFIG_DEBUG_UART=y
|
||||
+CONFIG_FIT=y
|
||||
+CONFIG_BOOTDELAY=30
|
||||
+CONFIG_AUTOBOOT_KEYED=y
|
||||
+CONFIG_AUTOBOOT_MENU_SHOW=y
|
||||
+CONFIG_DEFAULT_FDT_FILE="mediatek/mt7981-comfast-cf-wr632ax.dtb"
|
||||
+CONFIG_LOGLEVEL=7
|
||||
+CONFIG_PRE_CONSOLE_BUFFER=y
|
||||
+CONFIG_LOG=y
|
||||
+# CONFIG_BOARD_INIT is not set
|
||||
+CONFIG_BOARD_LATE_INIT=y
|
||||
+CONFIG_HUSH_PARSER=y
|
||||
+CONFIG_SYS_PROMPT="MT7981> "
|
||||
+CONFIG_CMD_CPU=y
|
||||
+CONFIG_CMD_LICENSE=y
|
||||
+CONFIG_CMD_BOOTMENU=y
|
||||
+CONFIG_CMD_ASKENV=y
|
||||
+CONFIG_CMD_ERASEENV=y
|
||||
+CONFIG_CMD_ENV_FLAGS=y
|
||||
+CONFIG_CMD_STRINGS=y
|
||||
+CONFIG_CMD_DM=y
|
||||
+CONFIG_CMD_GPIO=y
|
||||
+CONFIG_CMD_GPT=y
|
||||
+CONFIG_CMD_MTD=y
|
||||
+CONFIG_CMD_PART=y
|
||||
+CONFIG_CMD_TFTPSRV=y
|
||||
+CONFIG_CMD_RARP=y
|
||||
+CONFIG_CMD_CDP=y
|
||||
+CONFIG_CMD_SNTP=y
|
||||
+CONFIG_CMD_LINK_LOCAL=y
|
||||
+CONFIG_CMD_DHCP=y
|
||||
+CONFIG_CMD_DNS=y
|
||||
+CONFIG_CMD_PING=y
|
||||
+CONFIG_CMD_PXE=y
|
||||
+CONFIG_CMD_CACHE=y
|
||||
+CONFIG_CMD_PSTORE=y
|
||||
+CONFIG_CMD_PSTORE_MEM_ADDR=0x42ff0000
|
||||
+CONFIG_CMD_UUID=y
|
||||
+CONFIG_CMD_HASH=y
|
||||
+CONFIG_CMD_SMC=y
|
||||
+CONFIG_CMD_UBI=y
|
||||
+CONFIG_CMD_UBI_RENAME=y
|
||||
+CONFIG_OF_EMBED=y
|
||||
+CONFIG_ENV_OVERWRITE=y
|
||||
+CONFIG_ENV_IS_IN_UBI=y
|
||||
+CONFIG_ENV_REDUNDANT=y
|
||||
+CONFIG_ENV_UBI_PART="ubi"
|
||||
+CONFIG_ENV_UBI_VOLUME="ubootenv"
|
||||
+CONFIG_ENV_UBI_VOLUME_REDUND="ubootenv2"
|
||||
+CONFIG_ENV_RELOC_GD_ENV_ADDR=y
|
||||
+CONFIG_ENV_USE_DEFAULT_ENV_TEXT_FILE=y
|
||||
+CONFIG_ENV_DEFAULT_ENV_TEXT_FILE="defenvs/comfast_cf-wr632ax_env"
|
||||
+CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
|
||||
+CONFIG_VERSION_VARIABLE=y
|
||||
+CONFIG_NETCONSOLE=y
|
||||
+CONFIG_USE_IPADDR=y
|
||||
+CONFIG_IPADDR="192.168.1.1"
|
||||
+CONFIG_USE_SERVERIP=y
|
||||
+CONFIG_SERVERIP="192.168.1.254"
|
||||
+CONFIG_NET_RANDOM_ETHADDR=y
|
||||
+CONFIG_REGMAP=y
|
||||
+CONFIG_SYSCON=y
|
||||
+CONFIG_BUTTON=y
|
||||
+CONFIG_BUTTON_GPIO=y
|
||||
+CONFIG_CLK=y
|
||||
+CONFIG_GPIO_HOG=y
|
||||
+CONFIG_LED=y
|
||||
+CONFIG_LED_BLINK=y
|
||||
+CONFIG_LED_GPIO=y
|
||||
+# CONFIG_MMC is not set
|
||||
+CONFIG_MTD=y
|
||||
+CONFIG_DM_MTD=y
|
||||
+CONFIG_MTD_SPI_NAND=y
|
||||
+CONFIG_MTD_UBI_FASTMAP=y
|
||||
+CONFIG_PHY_FIXED=y
|
||||
+CONFIG_MEDIATEK_ETH=y
|
||||
+CONFIG_PHY=y
|
||||
+CONFIG_PINCTRL=y
|
||||
+CONFIG_PINCONF=y
|
||||
+CONFIG_PINCTRL_MT7981=y
|
||||
+CONFIG_POWER_DOMAIN=y
|
||||
+CONFIG_MTK_POWER_DOMAIN=y
|
||||
+CONFIG_DM_REGULATOR=y
|
||||
+CONFIG_DM_REGULATOR_FIXED=y
|
||||
+CONFIG_DM_REGULATOR_GPIO=y
|
||||
+CONFIG_RAM=y
|
||||
+CONFIG_DM_SERIAL=y
|
||||
+CONFIG_MTK_SERIAL=y
|
||||
+CONFIG_SPI=y
|
||||
+CONFIG_DM_SPI=y
|
||||
+CONFIG_MTK_SPIM=y
|
||||
+CONFIG_ZSTD=y
|
||||
+CONFIG_HEXDUMP=y
|
||||
--- /dev/null
|
||||
+++ b/defenvs/comfast_cf-wr632ax_env
|
||||
@@ -0,0 +1,54 @@
|
||||
+ipaddr=192.168.1.1
|
||||
+serverip=192.168.1.254
|
||||
+loadaddr=0x46000000
|
||||
+console=earlycon=uart8250,mmio32,0x11002000 console=ttyS0
|
||||
+bootcmd=if pstore check ; then run boot_recovery ; else run boot_ubi ; fi
|
||||
+bootconf=config-1
|
||||
+bootdelay=0
|
||||
+bootfile=openwrt-mediatek-filogic-comfast_cf-wr632ax-ubootmod-initramfs-recovery.itb
|
||||
+bootfile_bl2=openwrt-mediatek-filogic-comfast_cf-wr632ax-ubootmod-preloader.bin
|
||||
+bootfile_fip=openwrt-mediatek-filogic-comfast_cf-wr632ax-ubootmod-bl31-uboot.fip
|
||||
+bootfile_upg=openwrt-mediatek-filogic-comfast_cf-wr632ax-ubootmod-squashfs-sysupgrade.itb
|
||||
+bootled_pwr=red:status
|
||||
+bootled_rec=blue:status
|
||||
+bootmenu_confirm_return=askenv - Press ENTER to return to menu ; bootmenu 60
|
||||
+bootmenu_default=0
|
||||
+bootmenu_delay=0
|
||||
+bootmenu_title= [0;34m( ( ( [1;39mOpenWrt[0;34m ) ) )
|
||||
+bootmenu_0=Initialize environment.=run _firstboot
|
||||
+bootmenu_0d=Run default boot command.=run boot_default
|
||||
+bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return
|
||||
+bootmenu_2=Boot production system from NAND.=run boot_production ; run bootmenu_confirm_return
|
||||
+bootmenu_3=Boot recovery system from NAND.=run boot_recovery ; run bootmenu_confirm_return
|
||||
+bootmenu_4=Load production system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
|
||||
+bootmenu_5=Load recovery system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
|
||||
+bootmenu_6=[31mLoad BL31+U-Boot FIP via TFTP then write to NAND.[0m=run boot_tftp_write_fip ; run bootmenu_confirm_return
|
||||
+bootmenu_7=[31mLoad BL2 preloader via TFTP then write to NAND.[0m=run boot_tftp_write_bl2 ; run bootmenu_confirm_return
|
||||
+bootmenu_8=Reboot.=reset
|
||||
+bootmenu_9=Reset all settings to factory defaults.=run reset_factory ; reset
|
||||
+boot_first=if button reset ; then led $bootled_rec on ; run boot_tftp_recovery ; setenv flag_recover 1 ; run boot_default ; fi ; bootmenu
|
||||
+boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever
|
||||
+boot_production=led $bootled_pwr on ; run ubi_read_production && bootm $loadaddr#$bootconf ; led $bootled_pwr off
|
||||
+boot_recovery=led $bootled_rec on ; run ubi_read_recovery && bootm $loadaddr#$bootconf ; led $bootled_rec off
|
||||
+boot_ubi=run boot_production ; run boot_recovery ; run boot_tftp_forever
|
||||
+boot_tftp_forever=led $bootled_rec on ; while true ; do run boot_tftp_recovery ; sleep 1 ; done
|
||||
+boot_tftp_production=tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run ubi_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
|
||||
+boot_tftp_recovery=tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run ubi_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
|
||||
+boot_tftp=tftpboot $loadaddr $bootfile && bootm $loadaddr#$bootconf
|
||||
+boot_tftp_write_fip=tftpboot $loadaddr $bootfile_fip && run mtd_write_fip && run reset_factory
|
||||
+boot_tftp_write_bl2=tftpboot $loadaddr $bootfile_bl2 && run mtd_write_bl2
|
||||
+reset_factory=ubi part ubi ; mw $loadaddr 0x0 0x800 ; ubi write $loadaddr ubootenv 0x800 ; ubi write $loadaddr ubootenv2 0x800
|
||||
+mtd_write_fip=mtd erase fip && mtd write fip $loadaddr
|
||||
+mtd_write_bl2=mtd erase bl2 && mtd write bl2 $loadaddr
|
||||
+ubi_create_env=ubi check ubootenv || ubi create ubootenv 0x100000 dynamic || run ubi_format ; ubi check ubootenv2 || ubi create ubootenv2 0x100000 dynamic || run ubi_format
|
||||
+ubi_format=ubi detach ; mtd erase ubi && ubi part ubi ; reset
|
||||
+ubi_prepare_rootfs=if ubi check rootfs_data ; then else if env exists rootfs_data_max ; then ubi create rootfs_data $rootfs_data_max dynamic || ubi create rootfs_data - dynamic ; else ubi create rootfs_data - dynamic ; fi ; fi
|
||||
+ubi_read_production=ubi read $loadaddr fit && iminfo $loadaddr && run ubi_prepare_rootfs
|
||||
+ubi_read_recovery=ubi check recovery && ubi read $loadaddr recovery
|
||||
+ubi_remove_rootfs=ubi check rootfs_data && ubi remove rootfs_data
|
||||
+ubi_write_production=ubi check fit && ubi remove fit ; run ubi_remove_rootfs ; ubi create fit $filesize dynamic && ubi write $loadaddr fit $filesize
|
||||
+ubi_write_recovery=ubi check recovery && ubi remove recovery ; run ubi_remove_rootfs ; ubi create recovery $filesize dynamic && ubi write $loadaddr recovery $filesize
|
||||
+_init_env=setenv _init_env ; run ubi_create_env ; saveenv ; saveenv
|
||||
+_firstboot=setenv _firstboot ; run _switch_to_menu ; run _init_env ; run boot_first
|
||||
+_switch_to_menu=setenv _switch_to_menu ; setenv bootdelay 3 ; setenv bootmenu_delay 3 ; setenv bootmenu_0 $bootmenu_0d ; setenv bootmenu_0d ; run _bootmenu_update_title
|
||||
+_bootmenu_update_title=setenv _bootmenu_update_title ; setenv bootmenu_title "$bootmenu_title [33m$ver[0m"
|
||||
|
|
@ -26,6 +26,7 @@ abt,asr3000|\
|
|||
acer,predator-w6x-ubootmod|\
|
||||
asus,zenwifi-bt8-ubootmod|\
|
||||
cmcc,a10-ubootmod|\
|
||||
comfast,cf-wr632ax-ubootmod|\
|
||||
cudy,tr3000-v1-ubootmod|\
|
||||
h3c,magic-nx30-pro|\
|
||||
jcg,q30-pro|\
|
||||
|
|
@ -99,6 +100,7 @@ iptime,ax3000m)
|
|||
;;
|
||||
asiarf,ap7986-003|\
|
||||
cetron,ct3003|\
|
||||
comfast,cf-wr632ax|\
|
||||
edgecore,eap111|\
|
||||
netgear,wax220|\
|
||||
zbtlink,zbt-z8102ax|\
|
||||
|
|
|
|||
253
target/linux/mediatek/dts/mt7981b-comfast-cf-wr632ax-common.dtsi
Normal file
253
target/linux/mediatek/dts/mt7981b-comfast-cf-wr632ax-common.dtsi
Normal file
|
|
@ -0,0 +1,253 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "mt7981b.dtsi"
|
||||
|
||||
/ {
|
||||
aliases {
|
||||
label-mac-device = &gmac0;
|
||||
led-boot = &led_status_red;
|
||||
led-failsafe = &led_status_red;
|
||||
led-running = &led_status_blue;
|
||||
led-upgrade = &led_status_green;
|
||||
serial0 = &uart0;
|
||||
};
|
||||
|
||||
chosen: chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_status_blue: blue {
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_STATUS;
|
||||
gpios = <&pio 8 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_status_green: green {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_STATUS;
|
||||
gpios = <&pio 35 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_status_red: red {
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_STATUS;
|
||||
gpios = <&pio 34 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
status = "okay";
|
||||
|
||||
gmac0: mac@0 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <0>;
|
||||
label = "wan";
|
||||
phy-mode = "2500base-x";
|
||||
phy-handle = <&phy5>;
|
||||
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&macaddr_factory_e000 0>;
|
||||
};
|
||||
|
||||
gmac1: mac@1 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <1>;
|
||||
label = "lan";
|
||||
phy-mode = "gmii";
|
||||
phy-handle = <&int_gbe_phy>;
|
||||
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&macaddr_factory_e000 1>;
|
||||
};
|
||||
};
|
||||
|
||||
&fan {
|
||||
pwms = <&pwm 0 10000>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdio_bus {
|
||||
reset-gpios = <&pio 14 GPIO_ACTIVE_LOW>;
|
||||
reset-delay-us = <600>;
|
||||
reset-post-delay-us = <20000>;
|
||||
|
||||
phy5: phy@5 {
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
reg = <5>;
|
||||
};
|
||||
};
|
||||
|
||||
&pio {
|
||||
spi0_flash_pins: spi0-pins {
|
||||
mux {
|
||||
function = "spi";
|
||||
groups = "spi0", "spi0_wp_hold";
|
||||
};
|
||||
|
||||
conf-pu {
|
||||
pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
|
||||
drive-strength = <MTK_DRIVE_4mA>;
|
||||
bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
|
||||
};
|
||||
|
||||
conf-pd {
|
||||
pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
|
||||
drive-strength = <MTK_DRIVE_4mA>;
|
||||
bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
|
||||
};
|
||||
};
|
||||
|
||||
pwm0_pin: pwm0-pin-g0 {
|
||||
mux {
|
||||
function = "pwm";
|
||||
groups = "pwm0_0";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pwm {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pwm0_pin>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi0_flash_pins>;
|
||||
status = "okay";
|
||||
|
||||
spi_nand: spi-nand@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "spi-nand";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <52000000>;
|
||||
|
||||
spi-cal-enable;
|
||||
spi-cal-mode = "read-data";
|
||||
spi-cal-datalen = <7>;
|
||||
spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>;
|
||||
spi-cal-addrlen = <5>;
|
||||
spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
|
||||
|
||||
spi-tx-bus-width = <4>;
|
||||
spi-rx-bus-width = <4>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "BL2";
|
||||
reg = <0x00000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x0100000 0x0080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
factory: partition@180000 {
|
||||
label = "Factory";
|
||||
reg = <0x180000 0x0200000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
eeprom_factory_0: eeprom@0 {
|
||||
reg = <0x0 0x1000>;
|
||||
};
|
||||
|
||||
macaddr_factory_e000: macaddr@e000 {
|
||||
compatible = "mac-base";
|
||||
reg = <0xe000 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
|
||||
macaddr_factory_4: macaddr@4 {
|
||||
compatible = "mac-base";
|
||||
reg = <0x4 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
|
||||
macaddr_factory_8000: macaddr@8000 {
|
||||
compatible = "mac-base";
|
||||
reg = <0x8000 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@380000 {
|
||||
label = "FIP";
|
||||
reg = <0x380000 0x0200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
ubi: partition@580000 {
|
||||
label = "ubi";
|
||||
compatible = "linux,ubi";
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&xhci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
nvmem-cells = <&eeprom_factory_0>;
|
||||
nvmem-cell-names = "eeprom";
|
||||
status = "okay";
|
||||
|
||||
band@0 {
|
||||
reg = <0>;
|
||||
nvmem-cells = <&macaddr_factory_4 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
band@1 {
|
||||
reg = <1>;
|
||||
nvmem-cells = <&macaddr_factory_8000 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
};
|
||||
|
|
@ -0,0 +1,23 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "mt7981b-comfast-cf-wr632ax-common.dtsi"
|
||||
|
||||
/ {
|
||||
model = "COMFAST CF-WR632AX (OpenWrt U-Boot layout)";
|
||||
compatible = "comfast,cf-wr632ax-ubootmod", "mediatek,mt7981";
|
||||
};
|
||||
|
||||
&chosen {
|
||||
bootargs = "root=/dev/fit0 rootwait";
|
||||
rootdisk = <&ubi_rootdisk>;
|
||||
};
|
||||
|
||||
&ubi {
|
||||
reg = <0x580000 0x7a80000>;
|
||||
|
||||
volumes {
|
||||
ubi_rootdisk: ubi-volume-fit {
|
||||
volname = "fit";
|
||||
};
|
||||
};
|
||||
};
|
||||
18
target/linux/mediatek/dts/mt7981b-comfast-cf-wr632ax.dts
Normal file
18
target/linux/mediatek/dts/mt7981b-comfast-cf-wr632ax.dts
Normal file
|
|
@ -0,0 +1,18 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "mt7981b-comfast-cf-wr632ax-common.dtsi"
|
||||
|
||||
/ {
|
||||
model = "COMFAST CF-WR632AX";
|
||||
compatible = "comfast,cf-wr632ax", "mediatek,mt7981";
|
||||
};
|
||||
|
||||
&spi_nand {
|
||||
mediatek,nmbm;
|
||||
mediatek,bmt-max-ratio = <1>;
|
||||
mediatek,bmt-max-reserved-blocks = <64>;
|
||||
};
|
||||
|
||||
&ubi {
|
||||
reg = <0x580000 0x4000000>;
|
||||
};
|
||||
|
|
@ -127,6 +127,8 @@ mediatek_setup_interfaces()
|
|||
dlink,aquila-pro-ai-m60-a1)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" internet
|
||||
;;
|
||||
comfast,cf-wr632ax|\
|
||||
comfast,cf-wr632ax-ubootmod|\
|
||||
keenetic,kn-3911|\
|
||||
smartrg,sdg-8622|\
|
||||
smartrg,sdg-8632|\
|
||||
|
|
|
|||
|
|
@ -89,6 +89,7 @@ platform_do_upgrade() {
|
|||
bananapi,bpi-r4-lite|\
|
||||
cmcc,a10-ubootmod|\
|
||||
cmcc,rax3000m|\
|
||||
comfast,cf-wr632ax-ubootmod|\
|
||||
cudy,tr3000-v1-ubootmod|\
|
||||
gatonetworks,gdsp|\
|
||||
h3c,magic-nx30-pro|\
|
||||
|
|
@ -257,6 +258,7 @@ platform_check_image() {
|
|||
bananapi,bpi-r4-lite|\
|
||||
cmcc,a10-ubootmod|\
|
||||
cmcc,rax3000m|\
|
||||
comfast,cf-wr632ax-ubootmod|\
|
||||
cudy,tr3000-v1-ubootmod|\
|
||||
gatonetworks,gdsp|\
|
||||
h3c,magic-nx30-pro|\
|
||||
|
|
|
|||
|
|
@ -851,6 +851,44 @@ define Device/comfast_cf-e393ax
|
|||
endef
|
||||
TARGET_DEVICES += comfast_cf-e393ax
|
||||
|
||||
define Device/comfast_cf-wr632ax-common
|
||||
DEVICE_VENDOR := COMFAST
|
||||
DEVICE_MODEL := CF-WR632AX
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware kmod-hwmon-pwmfan kmod-usb3
|
||||
UBINIZE_OPTS := -E 5
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
KERNEL_IN_UBI := 1
|
||||
endef
|
||||
|
||||
define Device/comfast_cf-wr632ax
|
||||
DEVICE_DTS := mt7981b-comfast-cf-wr632ax
|
||||
IMAGE_SIZE := 65536k
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
SUPPORTED_DEVICES += cf-wr632ax
|
||||
$(call Device/comfast_cf-wr632ax-common)
|
||||
endef
|
||||
TARGET_DEVICES += comfast_cf-wr632ax
|
||||
|
||||
define Device/comfast_cf-wr632ax-ubootmod
|
||||
DEVICE_VARIANT := (OpenWrt U-Boot layout)
|
||||
DEVICE_DTS := mt7981b-comfast-cf-wr632ax-ubootmod
|
||||
UBOOTENV_IN_UBI := 1
|
||||
IMAGES := sysupgrade.itb
|
||||
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
|
||||
KERNEL := kernel-bin | gzip
|
||||
KERNEL_INITRAMFS := kernel-bin | lzma | \
|
||||
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
|
||||
IMAGE/sysupgrade.itb := append-kernel | \
|
||||
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
|
||||
ARTIFACTS := preloader.bin bl31-uboot.fip
|
||||
ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3
|
||||
ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot comfast_cf-wr632ax
|
||||
$(call Device/comfast_cf-wr632ax-common)
|
||||
endef
|
||||
TARGET_DEVICES += comfast_cf-wr632ax-ubootmod
|
||||
|
||||
define Device/confiabits_mt7981
|
||||
DEVICE_VENDOR := Confiabits
|
||||
DEVICE_MODEL := MT7981
|
||||
|
|
|
|||
Loading…
Add table
Reference in a new issue