Disabled the cache commands config CONFIG_CMD_CACHE. This changes
removes the icache and dcache commands.
Signed-off-by: Karthick Shanmugham <kartshan@codeaurora.org>
Change-Id: I0cfd4df12e452a15861f0df7f4512234113d315a
'flash wifi_fw' command writes into flash based
on 'rootfs' partition offset. After sysupgrade,
flashing single image at u-boot write wifi firmware
into failsafe partitions because post sysupgarde
primary and failsafe partitions are swapped vice-versa.
Single image always boots with primary partitions, and
the wifi firmware flashed into failsafe partition won't
be loaded subsequently q6 will crash.
This patch resolves issue by using "ubi" command's instead
of "flash wifi_fw" command.
Signed-off-by: Manikanta Mylavarapu <mmanikan@codeaurora.org>
Change-Id: I9a89872ade5cbd753272e11fd15e7b8f06d4f92c
Now, the linux-5.4 image is LZMA compressed enable the LZMA
decompressor support.
Signed-off-by: Kathiravan T <kathirav@codeaurora.org>
Change-Id: Ibfc0d1fb6ffc463182f944bea0aa1d76af7d57b5
Add BT state information to patch dts when the BT is started at bootloader.
Signed-off-by: Amandeep Singh <amansing@codeaurora.org>
Change-Id: Ib88150bb6c8469ec6d63578ce5c4ab21511aff60
This change will add support for Macronix "MX35UF1GE4AC" spi nand
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Change-Id: I66e82e22217d655b44e30baa64f3aefd5a5f2aaa
This change will add support for winbond "W25N02JWZEIF"
spi nand device.
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Change-Id: I1dd258c3f0f3174d09e74fb7ffd0c26a43e6c24b
This change will add support for giga device GD5F1GQ5REYIG
spi nand support.
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Change-Id: I57211ce34543de81216d86653a45519b97cf2fb0
This change will update blsp base address for i2c in
MP03.3rdp. Updated address from 78b6000 to 78b7000.
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Change-Id: Idd37550ac4cf012db0dfea16539d5c0948b13f40
Gpio out need to be enabled for
re-spin boards.
Signed-off-by: Manikanta Mylavarapu <mmanikan@codeaurora.org>
Change-Id: I711ed313170fb6268d1d5b9d70f2966bae481241
With latest GCC 4 byte aligned instructions are getting generated for
2 byte aligned data. This is due to the option '-fstore-merging' enabled
by default for '-O2'
This is causing data abort if data cache is disabled.
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Change-Id: Idaac94fcc8e5c61f0ea720ed0c10e908d3688c61
This patch moves the set_platform_specific_default_env
function outside of CONFIG_QCA_MMC as this function is
not dependent on that config.
This will cause unexpected behaviour if suppose MMC
config is disabled.
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Change-Id: I9bfc35afb054103bfb60b837cff04eed1d94decd
This change is to update the section name for wififw
in single-image with the QCN IDs when multiple wififw
images get packed.
Signed-off-by: Pavithra Palanisamy <pavip@codeaurora.org>
Change-Id: I56ab611a127b9958c38737684d856c51fabf7cd2
This patch updates the MDC and MDIO gpio strength from 2MA
to 8MA.
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Change-Id: Ie510d7ecaca1d22c97e4c8522050a76ba9b1b22c
This change will change serial training data read to one complete
page instead of 64-bytes read. Partial page read will cause some
data curroption issue if read request failed so read one complete page.
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Change-Id: Ibad101f096440e5dc10dfb4b3329a0aa6bddee7d
It will resolve usb probe failure in hs phy
without ss phy. It enables utmi clock instead
of pipe clock in hs phy only configuration.
Change-Id: Idaf140d2cbe068304f1ce87c443c8e2196e3433e
Signed-off-by: Manikanta Mylavarapu <mmanikan@codeaurora.org>
This change will fix proper clock source macro in set_clk_rate function.
Currently we are passing the wrong value to qpic_set_clk_rate for clock
source.
wrong:
qpic_set_clk_rate(IO_MACRO_CLK_200_MHZ, QPIC_IO_MACRO_CLK, NAND_QSPI_MSTR_CONFIG);
The last argument should be clock source not register base address.
correct:
qpic_set_clk_rate(IO_MACRO_CLK_200_MHZ, QPIC_IO_MACRO_CLK, GPLL0_CLK_SRC);
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Change-Id: Ie9e07c253220924fd0c9287f7f0e2c5d42351128
After reading data from mmc, dest pointer will point to
the end address. To calculate the start of dest pointer
number of bytes copied has to be subtracted.
Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Change-Id: I24610a3b3bb498c4ee4ebba58e557d109c6af1ef
