For the GS1920 the build system throws errors like
../dts/rtl8392_zyxel_gs1920-24hp-v1.dts:256.19-29:
Warning (reg_format): /switch@1b000000/ports/port@0:reg:
property has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
The dts misses the address and size properties for the
ports section. Fix that.
Fixes: 2a55846 ("realtek: add support for ZyXEL GS1920-24HPv1")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21534
Signed-off-by: Robert Marko <robimarko@gmail.com>
The interfaces attribute of the mdio bus held the information
about the connection mode (qsgmii, sgmii, ...). This was only
used during the old RTL930x setup. Drop it because it is not
needed any longer.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21469
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Cleanup the RTL930x polling setup. Make use of the
new phy fixup helper to initialize the polling registers.
As an integral update to the logic before only write
register bits that are really in scope. This might save
some bits set by U-Boot.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21469
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The mdio driver currently initializes the phy polling registers
with some nasty magic. It identifies the interface mode from the
dts and draws some strange conclusions.
Looking at the SDK one can see that this is basically dependent
of the attached phy type. So the code location is quite right
inside the mdio driver.
Provide a new get_phy_info() function that determines the phy
characteristics that are important for the polling unit . It will
be later needed by the RTL93xx setup code.
Some explanation about the fields of the structure:
- has_res_reg: phy has a special Realtek resolution polling
register. It is unclear if this gives more details or if it
simply allows faster polling.
- has_giga_lite: This is a phy that allows for Realtek proprietary
1G/2.5G lite connectivity. In this case data is only transmitted
over two wire pairs.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21469
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Currently there are several places where the driver uses the
classic "i" as iterator. In these cases where it iterates
phy ports use "addr" instead to make it easier to read. Do
the same for the smi bus. Additionally forthcomming commits
will show nicer diffs.
While we are here fix the initialization sequence of the private
structure. There is no need to set data to zero that has already
been zero-allocated before. Instead initialize smi_bus[] with
a value of "-1" to denote that a phy is not in scope. This is
essential as some functions already have a matching check in
place.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21469
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The mdio driver was carved out from the ethernet driver long
ago. Remove some leftover defines.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21502
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The mac_addr variable was not zero-initialized, causing weird side effects
when the memory contents were a valid MAC address.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Link: https://github.com/openwrt/openwrt/pull/21504
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The realtek target uses some functions marked __init for initialization.
However, that means they can only be called once when compiled in and
afterwards the memory occupied by them is freed and potentially reused.
Some "impossible" (code at a given location can't crash in the way it
does) crashes can be caused by this because upon re-execution of those
functions, garbage gets executed. Such re-execution can happen for
deferred probes or repeated probes.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Link: https://github.com/openwrt/openwrt/pull/21504
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Until now the RTL8214FC is initialized either by U-Boot (all
devices) or by some magic firmware file (RTL838x). On RTL839x
devices without U-Boot (e.g. ZyXEL GS1920) this PHY cannot
be used.
Provide the most basic setup sequence for RTL839x so that
copper/fiber work. Later it can be taken over for all devices
and the firmware helpers can be dropped.
Remark! This should not (but might) break RTL839x devices with
RTL8214FC U-Boot setup.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21435
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The RTL8214FC and the RTL8218B share the same register set and
need to be initialized quite similar. In the future the RTl8214FC
will get its own setup sequence. To keep the codebase small the
common parts (serdes & copper) will be covered by the existing
RTL8218B configuration.
Enhance the RTL8218B setup with this separate commit to ensure
that nothing breaks.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21435
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
No need to open code bus locking.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21435
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Commit ab805ec316 ("generic: add missing squashfs config") enabled
CONFIG_SQUASHFS_DECOMP_MULTI_PERCPU in the generic config, so it is no
longer needed in the target configs.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Link: https://github.com/openwrt/openwrt/pull/21465
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch RTL838X SerDes setup to use the internal SerDes hardware modes
instead of the PHY_INTERFACE_MODE_* modes.
Use the generic mapper in the beginning of the SerDes setup and convert
all affected functions to the different mode type. This will be moved
out to the generic pcs_config later.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21480
Signed-off-by: Robert Marko <robimarko@gmail.com>
We finally reached the point where PCS has full control over SerDes and
no parts of this are scattered in other drivers anymore. To make that
clear, drop the comment in pcs_config that explains this former state
and remove a warning which states that pcs_config isn't fully
implemented yet.
Add a generic output to at least keep a generic sign of life from the
PCS driver, independently from what the variant-specific code currently
prints.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21481
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a comment stating the situation around a specific RTL838x firmware
file. After SerDes setup has been moved to the PCS driver, this firmware
file is partially unused. If the remaining bits are pulled out or just
replaced, this firmware file can be dropped. The comment ensures that we
do not forget about that.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21481
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove some unused defines for SerDes in the ethernet driver. They have
been missed before but are completely out of place here now.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21481
Signed-off-by: Robert Marko <robimarko@gmail.com>
The GS1920-24HPv1 is a switch with 24 copper ports and 4 combo SFP/copper
ports and PoE on the first 24 ports.
Specifications:
---------------
* SoC: Realtek RTL8292M
* Flash: 16 MiB SPI flash
* RAM: 128 MiB
* Ethernet: 24x 10/100/1000 Mbps
* Buttons: 1x "Reset" button
* UART: 1x serial header, standard DCE pinout (Tx = 2, Rx = 3, Gnd = 5);
9600 baud, 8n1, +- 5.6V logic levels
* SFP: 4 combo copper/SFP ports
* PoE: 24x
* Fans: ADT7468 fan controller
Works:
------
- (24) RJ-45 ethernet ports
- Switch functions
- Buttons
- LEDs (partial support, the wrong LEDs light up)
- Manual fan control
Not yet enabled:
----------------
- PoE (requires patches to realtek-poe to support i2c)
- Combo ports (link is up, but no data is transferred)
Fans:
-----
After boot, the fans are running in full speed mode. You can interact
with the fan controller at /sys/class/hwmon/
Installation:
-------------
This device uses ZyNOS instead of Linux, this makes installation a bit
more cumbersome. Serial console is required!
1. Set the switch to boot from the first image. This step is crucial,
it will fail to boot if this is not set properly.
2. Connect to the switch using serial and interrupt the boot process
to enter debug/recovery mode.
3. Load the OpenWrt initramfs image via XMODEM. You need to obtain an
unlock code, based on your MAC address, first. See the excellent write
up at https://www.ixo.de/info/zyxel_uclinux/ for details. Replace
unlock_code in the commands below by the code obtained.
After running ATBA5, the terminal needs to be closed and re-opened
with 115200 baud. This speeds up the file transfer significantly!
The file length in bytes need to be given instead of file_length below.
You also need an XMODEM upload utility like "lrzsz-sx -X" to transfer
the file. Start the XMODEM upload after running the ATUPxxxx command:
> ATEN1,unlock_code
> ATBA5
> ATUP80100000,file_length
> ATGO80100000
4. Wait for OpenWrt to boot. Once this is done, transfer the loader binary
and the sysupgrade image to "/tmp" using scp.
5. Install OpenWrt permanently by running the following two commands on
the switch (over SSH):
> mtd write /tmp/loader.bin loader
> mtd write /tmp/sysupgrade.bin firmware
6. Reboot the switch and enjoy OpenWrt.
NB: You do not need to touch the loader binary unless it's recommended.
The loader is not part of a regular sysupgrade file and will be left
untouched. The boot loader only checks if the loader is valid to be
able to boot.
Recovery/ Return to stock:
--------------------------
Just spam the "u" key during (or "z" for 9600 baud) during memory testing
to trigger a recovery XMODEM upload at 115200 baud. A standard OEM upgrade
image works properly.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Link: https://github.com/openwrt/openwrt/pull/20439
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds the build recipes for rt-loader-standalone and zynsig to the
Makefile. The recipes are required for the upcoming ZyXEL GS1920 series.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Link: https://github.com/openwrt/openwrt/pull/20439
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for the Edgecore ECS4100-12PH, an 8-port 802.3bt PoE Gigabit
Ethernet switch with 2 combo RJ45/SFP and 2 SFP ports.
Hardware:
* SoC: RTL8393M
* RAM: 256MiB
* Flash: 32MiB SPI-NOR
* Ethernet:
* 8x GbE RJ45 PoE (external RTL8218B)
* 2x GbE RJ45 / SFP combo (external RTL8214FC)
* 2x SFP (external RTL8214FC)
* Console: RJ45 RS232 port on front panel
* PoE: Nuvoton M0516 + 2x Broadcom BCM59121 PSE
Installation via bootloader:
* open serial console (baud rate 115200)
* interrupt boot process by pressing any key during boot
* boot the OpenWrt initramfs:
# rtk network on
# tftpboot 0x8f000000 /tftpboot/openwrt-realtek-rtl839x-edgecore_ecs4100-12ph-initramfs-kernel.bin
# bootm
* copy openwrt-realtek-rtl839x-edgecore_ecs4100-12ph-squashfs-sysupgrade.bin
to /tmp and use sysupgrade to install it:
# sysupgrade /tmp/openwrt-realtek-rtl839x-edgecore_ecs4100-12ph-squashfs-sysupgrade.bin
Even though U-Boot claims the switch is based on the RTL8392M SoC, my
device is based on the RTL8393M SoC. I have confirmed this by removing
the heatsink, and the Linux kernel agrees with this. Therefore the DTS
has the rtl8393_ prefix.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Avoid family checks where possible. Now that the init_mac()
functions are in perfect shape include them into the
configuration structure. While we are here rename them
to the new driver prefix.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21391
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This function does nothing at the moment. Simply add it for
completeness.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21391
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Move the functions close to each other and sort them.
No functional changes here.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21391
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This function is now only called on RTL838x devices. Remove all
obsolete family checks.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21391
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The ethernet driver must initialize the chip for proper operation.
Currently there exist functions for RTL838x, RTL839x and RTL931x.
All of them are called differently. Combine them in a central call
location.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21391
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Replace remove_new callback in struct platform_driver with remove. This
was just meant for a transition period. remove_new is dropped with 6.13.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21430
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The SerDes access functionality in the mdio-realtek-otto drivers was
meant to be temporary, at least from a certain point on. The user was
all the SerDes configuration that lived in the PHY and DSA drivers.
Now that SerDes configuration has moved completely to the PCS driver,
there is no user of this code anymore. Instead, the PCS driver uses a
separate driver 'mdio-realtek-otto-serdes' to access the SerDes. Thus,
drop all that unused functionality from the "normal" mdio driver.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21439
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reading the fibre status of a RTL8214FC needs access to the
page register (31) and the extended page register (30).
The current implementation has two issues.
- The extended page register is not restored after changes
- Instead of register 30 its write-only sibling 29 is used.
This has the following side effect:
During regular polling kernel calls rtl8214fc_read_status
and determines the media status via __rtl8214fc_media_is_fibre.
Writing to register 29 a copy of that value is handed over
to register 30. This makes use of mdio tools for the first
port of the RTL8214FC hard. Register 30 is overwritten with
zero every second.
Change access from register 29 to register 30 and adapt
the sequence to restore register 30 contents at the end.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21393
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Drop several leftovers of SerDes configuration from PHY and DSA drivers.
Both drivers can be seen as free from any SoC-side SerDes stuff.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21360
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add the SerDes setup hooks in the PCS driver for RTL839x so that
pcs_config actually triggers configuration. Adjust the DTS of all
devices accordingly by adding pcs-handles and dropping phy-handles.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21360
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add a patch sequence needed to properly initialize 10G SerDes. This is
taken from the SDK mostly as-is ([1]).
Exit early from SerDes reset for now because it seems to cause some
issues on lower 5G SerDes.
[1] 30e7d6c8c2/sources/rtk-dms1250/src/dal/cypress/dal_cypress_construct.c (L215)
Co-authored-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21360
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add basic SerDes setup functionality which determines and sets the
hardware mode of a SerDes, and does a SerDes reset. This is restricted
to the 10G SerDes only as the 5G SerDes are setup properly by default.
Further initialization will be needed for the modes to function properly
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21360
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Refactor the previously added SerDes reset sequence. Use the SerDes
MDIO interface instead of plain writes into the switchcore's register
space. Moreover, simplify the sequence because the SDK version is
unnecessarily complex.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21360
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add SerDes reset sequence mostly as-is from the SDK (except for
adjusting the register write calls to work with regmap).
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21360
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The port media handling introduced before was to some extent just taken
over from the SDK. As a second step, improve that code now. Some code
can be deduplicated, a few statements removed and improved in general.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21385
Signed-off-by: Robert Marko <robimarko@gmail.com>
SFP modules still do not work that well across different devices. One
missing piece seems to be the bunch of magic values and bits set by the
SDK depending on which media is used on a port.
Take over code from the SDK for port media handling [1]. This applies
different sequences depending on whether it's 10G fiber, 1G fiber or DAC
cables to make it work best for each variant. Place the call to that
code below the configuration of a SerDes mode but before actually
activating that mode and powering on the SerDes. The SDK and our code
for RTL930x do that similarly.
Though we do not have any notion of media in pcs_config right now, do
similar to some SDK versions and set an appropriate media type for fiber
modes and SGMII (otherwise it doesn't work).
[1] 51c3390e0e/sources/rtk-dms1250/src/hal/phy/phy_rtl9310.c (L2302)
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21385
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Realtek SDK includes a lot of code around specific port media,
usually having quite some differences between 10G fiber, 1G fiber and
DAC cables. For each type, several magic values are set which in the end
usually make different kinds of links work optimal.
While there is currently no way to get that media information from the
kernel, add some fields as an enum to have a notion of different media
kinds. In additional steps, code for the subtargets can be taken over
from the SDK to handle different media.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21385
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop the '__always_unused' tags from two functions which are actually
used. This was missed during the big transition before.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21410
Signed-off-by: Robert Marko <robimarko@gmail.com>
Those config arrays still do not lineup with common conventions in the
driver in terms of naming. They are missing the driver and variant
prefix. Thus, line that up with how RTL930X code looks like.
- add 'rtpcs_' prefix since it's part of the PCS driver
- add '931x_' prefix because it's for RTL931X
- use 'cfg' instead of 'config' to shorten that a bit
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21410
Signed-off-by: Robert Marko <robimarko@gmail.com>
In the RTL931X configuration code, the array size of configuration
arrays was still calculated with 'sizeof(...) / sizeof(...)'. There's a
dedicated macro in the kernel for exactly that usecase. Use that instead
to avoid possible errors and make the line shorter. The RTL930X code is
already doing it the good way.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21410
Signed-off-by: Robert Marko <robimarko@gmail.com>
In kernel coding style, it is highly disregarded to hide structures
behind typedefs ([1]). The PCS driver still contains a typedef for the
sds_config which was taken over from the PHY driver.
- drop the typedef, just declaring it as a struct
- give it the common 'rtpcs_' prefix
- adjust all usage locations
[1] https://www.kernel.org/doc/html/v6.18/process/coding-style.html#typedefs
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21410
Signed-off-by: Robert Marko <robimarko@gmail.com>
I have contributed quite a lot changes recently and should be made
responsible for most of the code that has been added to the PCS driver
after it has been introduced by Markus.
FWIW, add myself as another module author so anything I produced here
doesn't fall back to someone else, i.e. Markus as currently the single
module author.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21410
Signed-off-by: Robert Marko <robimarko@gmail.com>
Convert all ops structures to the new rteth prefix.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21345
Signed-off-by: Robert Marko <robimarko@gmail.com>
Simplify netdev_ops initialization by moving the data
into the configuration structure.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21345
Signed-off-by: Robert Marko <robimarko@gmail.com>
The configuration data needs to reference the netdev_ops
in the future. Reorder it in a separate commit to avoid
confusion later.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21345
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is no need to set the cpu port depending on the
given family. Remove it from the private control structure
and add the fixed value to the configuration structure.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21345
Signed-off-by: Robert Marko <robimarko@gmail.com>
The name of the configuration structure suggests that it
contains a list of registers. As it contains functions too
change the name according to other realtek drivers.
- "Invent" a new driver prefix "rteth"
- Rename the structure and variables to config/cfg
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21345
Signed-off-by: Robert Marko <robimarko@gmail.com>
These patches fix bugs in a patch we backported.
These patch were cherry picked from upstream Linux because it references
a patch we backported in the fixes tag.
The patches were reordered to match the ordering in the upstream Linux kernel.
Fixes: 93173aee96 ("qualcommbe: ipq95xx: Add initial support for new target")
Link: https://github.com/openwrt/openwrt/pull/21366
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes a bug in a patch we backported.
This patch was cherry picked from upstream Linux because it references a
patch we backported in the fixes tag.
The first two patches are providing function needed by the last patch.
Fixes: 813ecda1f3 ("generic: backport phylink patches for PCS/PHY caps OPs")
Link: https://github.com/openwrt/openwrt/pull/21366
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes a bug in a patch we backported.
This patch was cherry picked from upstream Linux because it references a
patch we backported in the fixes tag.
The function phy_id_compare_vendor() is needed by the fix.
Refresh 782-05-v6.16-net-phy-Add-support-for-Aeonsemi-AS21xxx-PHYs.patch with the upstream code.
Fixes: 08a616b216 ("generic: backport support for Aeonsemi AS21xxx PHY")
Link: https://github.com/openwrt/openwrt/pull/21366
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
