075cdc0 iptime-crc32: add support for ipTIME AX3000Q
48ababa iptime-crc32: add support for ipTIME AX3000SM
f29de74 iptime-crc32: Add device support for ipTIME AX6000M
Link: https://github.com/openwrt/openwrt/pull/19520
(cherry picked from commit b087961ccb)
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19915
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
RTL83xx devices have two types of receive interrupts for each of its
8 rings. One for packet received and another for ring overflow. When
the switch is flooded with incoming packets the receive handler will
disable the packet receive notification but still keeps the overflow
notification enabled. While the receive path "slowly" processes the
received packets each new packet triggers the overflow IRQ again. The
device becomes unresponsive and eventually produces messages like:
[18441.709764] rcu: Stack dump where RCU GP kthread last ran:
[18441.727892] Sending NMI from CPU 1 to CPUs 0:
[18441.742300] NMI backtrace for cpu 0 skipped: idling at 0x8080e994
[18415.251700] rcu: INFO: rcu_sched detected stalls on CPUs/tasks:
[18415.271350] rcu: 0-...!: (0 ticks this GP) idle=d740/0/0x0 ...
[18415.303046] rcu: (detected by 1, t=6004 jiffies, g=230925, ...
[18415.326095] Sending NMI from CPU 1 to CPUs 0:
[18415.340540] NMI backtrace for cpu 0
Fix this issue by always disabling receive and overflow interrupts at
the same time.
Test with hping3 --udp -p 5021 -d 1400 --flood 192.168.2.72
Before (3sec run):
[183260.324846] rtl838x-eth 1b00a300.ethernet eth0: RX buffer overrun: status 0x101, mask: 0x7ffeff
[183260.340524] rtl838x-eth 1b00a300.ethernet eth0: RX buffer overrun: status 0x1, mask: 0x7ffeff
[183260.345799] net_ratelimit: 489997 callbacks suppressed
After (3 sec run):
[ 373.981479] rtl838x-eth 1b00a300.ethernet eth0: rx ring overrun: status 0x101, mask: 0x7fffff
[ 374.031118] rtl838x-eth 1b00a300.ethernet eth0: rx ring overrun: status 0x101, mask: 0x7fffff
[ 377.919996] net_ratelimit: 34 callbacks suppressed
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19365
(cherry picked from commit 963ee6ac3f)
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19891
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The IgniteNet SunSpot AC Wave2 comes with 2x QCA9994 ath10k chips
connected to the IPQ8068 SoC via PCIe.
Add board-2.bin for both radios on this board.
3ac4a64 qca9984: add BDFs for IgniteNet SS-W2-AC2600
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit d8303b4721)
Link: https://github.com/openwrt/openwrt/pull/19902
[Do not add ignitenet_ss-w2-ac2600]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We have modified the kernel to setup all "default" consoles,
including serial ports and framebuffers/screens, providing
no console= argument is supplied on the kernel command line.
Adding 'console=tty1' caused the 'default' serial port on
device tree systems to break, as the kernel would not carry
over the settings (like baud rate) from the bootloader.
The system administrator can still force the use of a
specific console by adding their own console= arguments.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Fixes: c099523d66 ("armsr: use console=tty1 to make
console more readily available")
Link: https://github.com/openwrt/openwrt/pull/17012
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit bff179de73)
Link: https://github.com/openwrt/openwrt/pull/19894
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
A previous change added 'console=tty1' to the default kernel command
line on armsr, in order to ensure the framebuffer console is enabled
on systems capable of graphics output.
Unfortunately, this change broke boards that used device tree
(DT) firmware with serial consoles, as the serial console
specified by the system firmware (stdout-path) was no longer
setup by the kernel.
A bit of probing determined that the SPCR (serial port console
direction table) on ACPI systems was preventing Linux from setting
up a default framebuffer console on these systems (which is why
console=tty1 was added).
(The affected ACPI systems are usually VMs using QEMU's
'virt' machine and EDK2 firmware. The firmware on these systems
does not remove the SPCR when a screen is present)
So to ensure all possible systems are setup correctly, we modify
the kernel so all "default" console types (serial and screen)
are setup when no console= arguments are specified on the kernel
command line.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Fixes: c099523d66 ("use console=tty1 to make console more
readily available")
Link: https://github.com/openwrt/openwrt/pull/17012
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3697022ce3)
Link: https://github.com/openwrt/openwrt/pull/19894
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6e4ffe2c6657 ucode: add function for getting the number of entries in a snapshot
a62edd89255b ucode: add support for fetching kernel tracepoint events
edeb4d6dc690 udebug-cli: add support for streaming tracing data
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 78188ee2bc)
3d953628bf17 udebugd: add support for setting an override config
93f6df0240e5 udebug-cli: add support for overriding config on the command line
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit c4e7b9b9b7)
The vendor DTS defined incorrect GPIOs for the LEDs, which caused them
to not function properly. Initially, the WAN, WLAN LEDs appeared to
work, but further testing showed that they were non-functional.
This patch corrects the GPIO assignments in the DTS, restoring full LED
functionality including blinking, except the power LED which cannot be
software controlled.
Tested on a CF-EW71 v2 unit.
Fixes: ee3a6adc6c ("ath79: add support for Comfast CF-EW71 v2")
Signed-off-by: Felix Golatofski <git@xdfr.de>
Link: https://github.com/openwrt/openwrt/pull/19665
(cherry picked from commit 9ce23ac840)
Link: https://github.com/openwrt/openwrt/pull/19839
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This enables software that requires this cipher suite (e.g. OpenThread Border
Router) to be compiled against the shared library rather than a separate copy.
Signed-off-by: Karsten Sperling <ksperling@apple.com>
Link: https://github.com/openwrt/openwrt/pull/19489
(cherry picked from commit 97dc9f8dbf)
Link: https://github.com/openwrt/openwrt/pull/19839
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is some confusion in the Git log of this file. Specifically,
the commit message on 7b7f1702 incorrectly indicates that there was
"potential fear" about copyright infringement.
Upon review of this situation, there is, in my opinion, no concern of
copyright infringement here. This is not legal advice; it is my
opinion based of years of work on copyright policy for FOSS.
However, Elliott Mitchell's idea was obviously helpful as inspiration
in writing this script and deserves credit. Ideas alone, however,
are not to my knowledge copyrightable anywhere in the world.
Signed-off-by: Bradley M. Kuhn <bkuhn@sfconservancy.org>
(cherry picked from commit d8e738e5c4)
Link: https://github.com/openwrt/openwrt/pull/19839
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The interrupt handler reads from the mailbox if no other reason for the
interrupt is known. If a spurious interrupt is received just after a
mailbox message has been sent, this means that the response to the
previous message is read again and returned by DSL_BSP_SendCMV instead
of the actual response.
To fix this, check the status register before reading from the mailbox
in the interrupt handler.
Tested on Fritzbox 7320. Without this change, there is occasionally a
kernel panic due to an out-of-bounds memory access in the ltq-adsl
driver (in DSL_DRV_DEV_G997_SnrAllocationNscGet), as a result of an
incorrect value returned by DSL_DRV_DANUBE_CmvRead. This is reproducible
by calling "dsl_cpe_pipe.sh g997dsnrg 1 1" multiple times.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19385
(cherry picked from commit 6889ea7b9a)
Link: https://github.com/openwrt/openwrt/pull/19839
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The IPQ4019 datasheet indicates that the maximum supported SPI
frequency is 25 MHz. My experiment on SKSpruce WIA3300-20 shows
that exceeding this threshold can lead to instability of SPI
peripheral. Limit the SPI clock frequency to the QSDK recommended
value 24MHz to enhance stability.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19744
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3ff8a3dca8)
Link: https://github.com/openwrt/openwrt/pull/19796
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
PR of openwrt:main: https://github.com/openwrt/openwrt/pull/19512
OpenFi 6C is a portable Wi-Fi 6 travel router based on MediaTek MT7981B+MT7976CN.
Two slightly different versions have been sold. The V1 board has a green color and lacks the modem LED. The V2 board is black and has a LED for the modem.
Specifications:
- SoC: MediaTek MT7981B (Filogic 820) 1.3GHz dual-core ARM Cortex-A53
- RAM: 1GB DDR4
- Flash: 256MB SPI NAND
- Wireless: 2.4GHz/5GHz 802.11ax
- Ethernet: 1x 10/100/1000M LAN
- USB: 1x USB 3.0 Type-A port
- Expansion: M.2 slot for 5G modem
- Cooling: PWM-controlled fan
- Buttons: Reset, Mode switch
- LEDs: System, Ethernet, 5G WiFi, Modem status
**Installation via U-Boot web page**
1. Set static IP 192.168.21.2/255.255.255.0 on your computer.
2. Connect to the Ethernet port and hold the reset button while booting the device. Wait for 6-8 seconds, and release the reset button.
3. Open U-boot web page on your browser at http://192.168.21.1
4. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
5. Wait for automatic reboot.
**Installation via sysupgrade**
Flash the sysupgrade file via LuCI upgrade page without saving the settings.
Signed-off-by: Jiasheng Zhu <newbanyaya@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19512
(cherry picked from commit 536a25ebf8)
Link: https://github.com/openwrt/openwrt/pull/19536
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, if OEM recovery flashes OpenWrt to second ubi1,
OpenWrt cannot boot. With this commit, recovery image is built
with initramfs kernel, so that it can boot from either ubi or ubi1.
This adds an extra step to OpenWrt installation from OEM:
user needs to sysupgrade from initramfs to full system.
Signed-off-by: Mateusz Krzak <kszaquitto+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18878
(cherry picked from commit 6615c8cfc8)
Signed-off-by: Mateusz Krzak <kszaquitto+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19595
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an industrial 4G router equipped with OpenWrt SNAPSHOT OEM
customized version
WARNING: The original firmware device tree is modified from evb
boards, and the device tree name is evb board. This submitted device
tree is a modified version, which deletes the non-this-device parts
and adds GPIO watchdog.
Specification:
- SoC: MediaTek MT7628NN
- Flash: 16 MB
- RAM: 128 MB
- Power: DC 5V-36V 1.5A
- Ethernet: 1x WAN [slot not install], 1x LAN (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only [antenna not install]
- LED:
System/Power (RUN): GPIO/37 active-low
Modem: GPIO/3 active-low
RF (Modem Signal): GPIO/2 active-low
- Button:
WPS / RESET: GPIO/11 active-low
- UART: 1x UART on PCB - 115200 8N1
- Serial / COM: 1X RS232/RS485 on board (GPIO/6 hi:RS485 lo:RS232)
- GPIO Watchdog: GPIO/0 mode=toggle timeout=1s
- Modem: 1x Built-in modem on board (Power: GPIO/4 active-high)
- PCIe: 1x miniPCIe for modem [slot not install]
- SIM Slots: 1x SIM Slots
Issue:
- Factory partition not store mac address on original firmware
Flash instruction:
Using SSH/Telnet:
1. Connect the board to the computer via RJ45 Ethernet
2. Login 192.168.8.1 with root password "superzxmn" (SSH Port 22, Telnet Port 5188)
3. Download openwrt firmware on the computer.
4. Use scp or sftp put firmware to board /tmp
5. Use command "mtd -r write openwrt-ramips-mt76x8-hongdian_h7920-v40-squashfs-sysupgrade.bin firmware"
to flash
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-hongdian-h7920-v40-and-flash.html
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
(cherry picked from commit ebee946227)
Link: https://github.com/openwrt/openwrt/pull/19716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport some flow offload helper patch in preparation for Airoha Flow
Offload support.
Link: https://github.com/openwrt/openwrt/pull/18166
(cherry picked from commit 34ba7e8a8a)
[ drop merged patch 705-v6.12-netdevice-add-netdev... ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backpot upstream patch for Flow Offload support for AN7581 and refresh
all affected patch. To correctly work a dedicated firmware is needed to
use the dedicated Network Coprocessor (NPU).
This also introduce good cleanup and moves the driver in a dedicated
Airoha directory. While currently not totally usable (due to lack of
firmware blob) this is needed to backport support for external PHY/SFP
support.
Refresh all affected patch.
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # tested on Quantum W1700k
Tested-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18166
(cherry picked from commit ad2077165b)
[ refresh patches ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport some upstream patch for Airoha ethernet driver in preparation
for Flow Offload support.
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # tested on Quantum W1700k
Tested-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18166
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit afea8bda0d)
Replace PCIe patch with upstream version and update DTS with new PBUS
CSR property now required.
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # tested on Quantum W1700k
Tested-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18166
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 921d438564)
Removes the need for a remove function in platform_device.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18660
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit aa4c96b925)
Drop Airoha MTD parser patch as a better solution was agreed with a
fixed partition table.
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # tested on Quantum W1700k
Link: https://github.com/openwrt/openwrt/pull/18112
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 90dee1ab30)
This got added in commit 15887235, cherry-picked into the 24.10 branch
as 642b5b61 and was partially lost in a manual patch refresh in
3a2a2c99.
The main branch still contains the full set of rx DMA size changes, so I
assume it was lost by accident.
With rx.dma_size=2K, my TP-Link Archer MR600v2 (MT7621) randomly reboots
due to OOM.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
In the conversion to dts, qca,led-pin was used for both interfaces.
Unfortunately, it's mutually exclusive with gpio-controller which made
it not do anything.
Fixes: 949e1a0 ("mpc85xx: tl-wdr4900: move platform code to dts")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19758
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit cc0ff28f23)
The bootup of the armsr target sometimes failed like this:
```
[ 0.762283] NET: Registered PF_INET6 protocol family
[ 0.791987] workqueue: Failed to create a worker thread: -EAGAIN
[ 0.801986] workqueue: Failed to create a rescuer kthread for wq "mld": -EAGAIN
[ 0.964017] NET: Unregistered PF_INET6 protocol family
```
Increase the maximum number of threads the kernel allows.
Link: https://github.com/openwrt/openwrt/pull/19376
(cherry picked from commit c5330bdf7e)
Link: https://github.com/openwrt/openwrt/pull/19554
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
