This change adds a new command to support the qcn9224 fusing.
Fuser blower binary should be transfered via tftp to Host and
using fuse_qcn9224 command, binary can be transfered to qcn9224.
qcn9224 will take care of the fusing.
sample command:
tftpboot fuse_blower.bin
fuse_qcn9224 0
Change-Id: Ie8cd73a2d49799100bd1f717cdc4b8dad070f9bd
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
Adding a new command mibib_reload to
populate the partition table info from
mibib binary
Change-Id: I3f08fc07ea55f1bbd90dc28d8f459d108f86bc0e
Signed-off-by: Timple Raj M <quic_timple@quicinc.com>
removing the redundant initialization to reduce the size of uboot
Change-Id: I4a129bfc1bad4e402a66a1b1051d1f432a581a6e
Signed-off-by: Timple Raj M <quic_timple@quicinc.com>
These modifications enable TZ+TME to obtain information
about the boot image partition for validation.
Change-Id: If4e6f27eb2c0e38fa8ec0ad552838f1d7a8c34c1
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
This patch updates the default load address CONFIG_SYS_LOAD_ADDR
to 0x50000000. Earlier address could not accommodate the larger
single image file, hence this update.
Change-Id: I94b0324a7a65e53af1a2d839b8b7eafeb69c0eef
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
These changes only add GZIP support for the
default u-boot; they do not apply to the tiny u-boot.
Change-Id: I1f022b77d6c2a82bdff36073746b409e126b5d35
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
This update replaces the board-specific QPIC nand
training offset fixup with a generic framework.
Change-Id: I0fd9203334da3846cfbbba880bc6b4701e9d162b
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
These changes add crashdump support in devsoc platform.
Change-Id: Ifdb9e1e65a4e93407506e987201b4ddeac753927
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
Update the feature to use BIT10 and BIT11 for NONHLOS
and HLOS failure detection instead of BIT9 & BIT10.
Change-Id: Idb649770da0cba63554adce861e901f582637c86
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
This patch disables unused configs to reduce
U-Boot image size. This is required since
the image size was very close to the partition
size.
Change-Id: Ibd3131cb0f579deb3d34aff6857c97ca7338af19
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This patch adds initial support for qca8084 PHY
which is based on qca8081 PHY.
qca8084 PHY has support for 4x2.5G.
Change-Id: Ic767c19fad050e5ee9a97ad7fa50c1b6b27893dd
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
The PCIE node is disabled by default in
the emulation platform
Change-Id: I51041186a57d08b58c1f7c85dd1a90fbeb24aac9
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
This change adds support to enable multiple I2C bus on all IPQ
platforms. Removed the device specific changes and updated in
a generic way to support multiple I2C on all the IPQ platforms.
Change-Id: Ie13dd744c6317fc9245bc88781e79a9fb3621a62
Signed-off-by: Ram Kumar D <quic_ramd@quicinc.com>
This changes enable UBI command support in
devsoc platform.
Change-Id: I2dade2f7ab232f6ae3f2a800437e1543e6a85909
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
This changes enable dcache enable and disable support
and also enable dcache command.
Change-Id: I7a11a923c1f87168e9cb519c5dedfcfac2dbc610
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
This patch changes the USB port scanning procedure and timeout
handling in the following ways:
a)
The power-on delay in usb_hub_power_on() is now reduced to a value of
max(100ms, "hub->desc.bPwrOn2PwrGood * 2"). The code does not wait
using mdelay, instead usb_hub_power_on() will wait before querying
the device in the scanning loop later. The total timeout for this
hub, which is 1 second + "hub->desc.bPwrOn2PwrGood * 2" is calculated
and will be used in the following per-port scanning loop as the timeout
to detect active USB devices on this hub.
b)
Don't delay the minimum delay (for power to stabilize) in
usb_hub_power_on(). Instead skip querying these devices in the scannig
loop until the delay time is reached.
c)
The ports are now scanned in a quasi parallel way. The current code did
wait for each (unconnected) port to reach its timeout and only then
continue with the next port. This patch now changes this to scan all
ports of all USB hubs quasi simultaneously. For this, all ports are added
to a scanning list. This list is scanned until all ports are ready
by either a) reaching the connection timeout (calculated earlier), or
by b) detecting a USB device. This results in a faster USB scan time as
the recursive scanning of USB hubs connected to the hub that's currently
being scanned will start earlier.
One small functional change to the original code is, that ports with
overcurrent detection will now get rescanned multiple times
(PORT_OVERCURRENT_MAX_SCAN_COUNT).
Without this patch:
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 9 USB Device(s) found
time: 20.163 seconds
With this patch:
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 9 USB Device(s) found
time: 1.822 seconds
So ~18.3 seconds of USB scanning time reduction.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
(cherry picked from commit c998da0d67)
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
Change-Id: I520082122370dda5b1de63c2ebee0f9a63fdef92
ipq9574 is a TME-L based platform in which before
encrypt/decrypt, we are required to derive a key
handle.
This patch adds support for the same.
Change-Id: I583cee87607af2ab6461b429830cb8ff43cc44d4
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This config is needed to enable mmc protection
based on gpt readonly attribute.
Usecase:
1. In emmc partition xml, set readonly attribute
of a partition to true.
2. Generate partition bin, flash and reboot.
3. From uboot, read & write the partition.
4. Write should not go through. Crc32 checksum of
the content before & after write should match.
Change-Id: I1b5b4593d99d0ddab4d37b29c3669a4c805e80ea
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
This changes add support for uboot base files.
Change-Id: I5f4b937dec30a27ec6acce6ceada7fbed5d5a41d
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
Removing this config will configure the tftp block
size to default value of 1468 + headers which is the
same as in other platforms.
Change-Id: If0b49217e5d2548be203a1a7da4000cd5f2e5dcb
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
This changes enables the QSPI_LAYOUT_SWITCH config
which is required for QSPI nand 4k support.
Since SBL must be flashed in 2K layout to support
QSPI Nand-4K, this dynamic switch is required.
Change-Id: I95a68ec9238dd83306322bc57cf93b162e3179f5
Signed-off-by: Vandhiadevan Karunamoorthy <quic_vkarunam@quicinc.com>
Certain boards come in different variations by way of utilizing daughter
boards, for example. These boards might contain additional chips, which
are added to the main board's busses, e.g. I2C.
The device tree support for such boards would either, quite naturally,
employ the overlay mechanism to add such chips to the tree, or would use
one large default device tree, and delete the devices that are actually
not present.
Regardless of approach, even on the U-Boot level, a modification of the
device tree is a prerequisite to have such modular families of boards
supported properly.
Therefore, we add an option to make the U-Boot device tree (the actual
copy later used by the driver model) writeable, and add a callback
method that allows boards to modify the device tree at an early stage,
at which, hopefully, also the application of device tree overlays will
be possible.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
(cherry picked from commit 2a792753d6)
Signed-off-by: Ram Kumar D <quic_ramd@quicinc.com>
Change-Id: I9a5fe4c6d681aaa5c68edd8a2a39d36bf2340fdf
Add failsafe boot support to recover from system hang.
Signed-off-by: anusha <anusharao@codeaurora.org>
Change-Id: I49e28a4e88aa16e564065d06f8701dc4f6cb3555
Added read & write bam pipe entires in all the ipq specific dtsi.
Also, updated the spi bam code with generic code changes to enable
the multiple spi support on all ipq chipsets.
Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Signed-off-by: Ram Kumar D <ramd@codeaurora.org>
Change-Id: Ibcdb9d2a9ff7a25f3d296ecdb1aca403511e07d7
