There is now an implementation of .set_autoneg and .restart_autoneg for
all variants. Remove the helper function which checks for it, and just
call the operation directly.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/21934
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
RTL83xx uses the BMCR and ADVERTISE registers like RTL93xx to configure
in-band auto-negotiation. Split out the common parts as a new generic
implementation and use it for RTL83xx. RTL93xx retains its own variant
of set_autoneg to support XSGMII, but calls into the generic version for
all other modes.
Tested 1000Base-X auto-negotiation on HPE 1920-8G (RTL8380). Also tested
HPE 1920-24G (RTL8382) and HPE-1920-48G (RTL8393) to make sure this does
not affect PHY ports.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/21934
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ZTE MF833U1 is a LTE dongle that expose a cdc_ether interface for data link
and WebUI for management. It handles all the "modem" functionalities
internally and does not expose any serial interface. Instead it acts like a
"router in a stick".
It initially enumerates as a USB mass-storage device and does not bind any
network driver, so no netdev is created until a modeswitch is performed.
The test is done on Cudy TR3000 256MB v1.0 running OpenWrt 24.10.5 with an
unit targeting Chinese market:
- Hardware Version: MF883U1_V1.0.0
- Software Version: BD_MF883U1V1.0.0B06
- CMIT ID: 2019CP2106
There are report online that the device have different variants that have
different behavior across different firmware, HW revisions or SKUs.
Before the switch:
```
root@OpenWrt:~# lsusb -t
/: Bus 001.Port 001: Dev 001, Class=root_hub, Driver=xhci-mtk/1p, 480M
|__ Port 001: Dev 003, If 0, Class=[unknown], Driver=[none], 480M
root@OpenWrt:~# lsusb Bus 001 Device 001: ID 1d6b:0002 Linux 6.6.119
xhci-hcd xHCI Host Controller Bus 001 Device 004: ID 19d2:1705
DEMO,Incorporated DEMO Mobile Boardband Bus 002 Device 001: ID 1d6b:0003
Linux 6.6.119 xhci-hcd xHCI Host Controller ```
After the switch:
```
root@OpenWrt:~# lsusb -t
/: Bus 001.Port 001: Dev 001, Class=root_hub, Driver=xhci-mtk/1p, 480M
|__ Port 001: Dev 003, If 0, Class=[unknown], Driver=cdc_ether, 480M
|__ Port 001: Dev 003, If 1, Class=[unknown], Driver=cdc_ether, 480M
|__ Port 001: Dev 003, If 2, Class=[unknown], Driver=[none], 480M
/: Bus 002.Port 001: Dev 001, Class=root_hub, Driver=xhci-mtk/1p, 20000M/x2
root@OpenWrt:~# lsusb Bus 001 Device 001: ID 1d6b:0002 Linux 6.6.119
xhci-hcd xHCI Host Controller Bus 001 Device 003: ID 19d2:1706
DEMO,Incorporated DEMO Mobile Boardband Bus 002 Device 001: ID 1d6b:0003
Linux 6.6.119 xhci-hcd xHCI Host Controller ```
The following kernel debug log is presented:
``` cdc_ether 1-1:1.0 eth2: register 'cdc_ether' at usb-11200000.usb-1, ZTE
CDC Ethernet Device, 34:4b:50:00:00:00 ```
Signed-off-by: Zihao Diao <hi@ericdiao.com>
Link: https://github.com/openwrt/openwrt/pull/21867
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Increase PKG_RELEASE so buildbots pick up and rebuild the updated
package files.
Fixes: c752525511 ("xdp-tools: add patch to fix stddef.h build issue")
Link: https://github.com/openwrt/openwrt/pull/21988
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add support for the TP-Link EAP683-LR, an AX6000 Ceiling Mount WiFi 6
AP.
Hardware:
* SoC: MediaTek MT7896AV
* RAM: 1GiB DDR4 (Samsung K4A8G165WC-BCTD)
* Flash: 128MiB SPI-NAND (ESMT F50L1G41LB)
* Ethernet: 1x 10/100/1000/2500 Mbps PoE-PD (MaxLinear GPY211C)
* WiFi: MT7976AN/MT7976GN 2.4/5GHz 4T4R
* LEDS: 3x blue connected to a single GPIO line
* Buttons: 1x reset
* BLE/Thread/Zigbee: CC2652
Stock firmware uses a random MAC address for ethernet, label MAC for
2.4 and label MAC + for 5GHz.
Installation via bootloader:
* Solder JST??? connector on J255, alternatively solder wires on the
TP13-TP15 pads. Pinout: TP13: TX, TP14: RX, TP15: GND, TP16: VCC.
The pins for J255 are in the same order.
* Interrupt boot process by repeatedly pressing Ctrl+b during boot
* In the boot menu, select U-Boot console
* Ensure the U-Boot environment variable "tp_boot_idx" is not set:
# setenv tp_boot_idx
# saveenv
* Boot the OpenWrt initramfs:
# tftpboot openwrt-mediatek-filogic-tplink_eap683-lr-initramfs-kernel.bin
# bootm
* copy openwrt-mediatek-filogic-tplink_eap683-lr-squashfs-sysupgrade.bin
to /tmp and install it using sysupgrade
Flashing via OEM firmware is currently not supported. The
tplink-safeloader utility does not recognize the OEM firmware:
DEBUG: can not find fwuphdr
Firmware image partitions:
base size name
Segmentation fault (core dumped)
To revert to the OEM firmware, you can set the U-Boot environment
variable "tp_boot_idx" to 1 via bootloader, or using fw_setenv via
OpenWrt. This should result in booting from the ubi1 partition, which
OpenWrt should not touch. Then use the web interface to upgrade
firmware: System > Firmware Update.
The OEM firmware uses 0x800000 for the runtime_backup partition size.
This causes the following warning:
mtd: partition "runtime_backup" extends beyond the end of device "nmbm_spim_nand" -- size truncated to 0x600000
This is due to the NMBM reserved blocks. Use 0x600000 in our DTS.
Thanks to init Lab's user890104, who soldered jumper wires on the TTL
pads for me so I could have serial console. My soldering skills just
aren't good enough to pull that off without risk damaging things.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add a patch that avoids including <stddef.h> in BPF headers, fixing
build failures on OpenWrt toolchains where the header is unavailable:
In file included from xdpfilt_dny_udp.c:10:
In file included from ./xdpfilt_prog.h:24:
../lib/../headers/xdp/parsing_helpers.h:18:10: fatal error: 'stddef.h' file not found
18 | #include <stddef.h>
| ^~~~~~~~~~
1 error generated.
make[5]: *** [../lib/common.mk:111: xdpfilt_dny_udp.o] Error 1
make[4]: *** [Makefile:40: xdp-filter] Error 2
Link: https://github.com/openwrt/openwrt/pull/21972
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add the required patches in order to backport cake-mq from Linux 7.0.
Many thanks to Toke Høiland-Jørgensen for providing the git trees with backports
for both 6.12 and 6.18.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21964
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Bootlog has the following line:
mt7915e 0000:01:00.0: missing precal data, size=403472
It is because precal was not included in the previous NVMEM conversion.
Fix this by adding it to the dts.
Fixes: dbc2923cbe ("mediatek: filogic: convert Acer Predator W6 to use NVMEM framework")
Signed-off-by: Zhi-Jun You <hujy652@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/21894
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Bootlog has the following line:
mt7915e 0000:01:00.0: missing precal data, size=403472
It is because precal was not included in the previous NVMEM conversion.
Fix this by adding it to the common dts.
Fixes: dbc2923cbe ("mediatek: filogic: convert Acer Predator W6 to use NVMEM framework")
Signed-off-by: Zhi-Jun You <hujy652@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/21894
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Bootlog has the following line:
mt798x-wmac 18000000.wifi: missing precal data, size=403472
It is because precal was not included in the previous NVMEM conversion.
Fix this by adding it to the common dtsi.
Fixes: dbc2923cbe ("mediatek: filogic: convert Acer Predator W6 to use NVMEM framework")
Signed-off-by: Zhi-Jun You <hujy652@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/21894
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update the default kernel path in start_qemu_malta() to match the new
image naming scheme after the malta target was converted to the Device
macro system with device name 'generic'.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Convert the malta target from the legacy Image/BuildKernel and
Image/Build pattern to the modern Device macro system. This is the
last target still using the legacy pattern.
The Device macro system automatically generates per-image JSON
metadata files which get aggregated into profiles.json, enabling
firmware selector and other tooling support for all malta subtargets
(be, le, be64, le64).
The kernel ELF is produced via KERNEL_NAME := vmlinux.elf (matching
octeon), uImage artifacts are built using the standard Build/lzma,
Build/gzip and Build/uImage commands with the existing load address
0x80100000, and rootfs images use append-rootfs with optional gzip
compression.
The device is named 'generic' following the convention used by other
virtual/emulated targets (x86, armsr, octeon).
Signed-off-by: Paul Spooren <mail@aparcar.org>
These devices share the same "compatible" in device tree causing some
incompatibilities (sysupgrades, ASU profile identification), assign a
unique "compatible" and "model" to each variant.
Context:
Commit [1] added each variant's dts compatible to the SUPPORTED_DEVICES
field of the other variant to make easy sysupgrades between these
physically indistinguishable devices variants possible.
But there were found three issues which does not allow this:
- the sysupgrade's stricter check still used in some sysupgrade
paths(this check is being replaced(and redundant) with the newer fwtool's
SUPPORTED_DEVICES check using the info in images METADATA), this check
will fail when sysupgrading from a different board_name(compatible dts)
that the image was created for (image profile name).[2]
- ASU needs unique "dts compatible" to identify the devices profile.
- and an ASU's profile identification limitation when several devices from
a common target share SUPPORTED_DEVICES entries.[3]
There is a proposal for these issues but not yet implemented [4][3].
Until these issues are fixed we won't allow "easy" sysupgrades between
these two device variants.
Commit [5] avoided the ASU profile identification limitation but
missed the required two unique dts compatibles in order to make the two
variants fully work, although not allowing easy sysupgrade between them.
[1]: 8d30e07180
[2]: sysupgrade stricter check https://github.com/openwrt/openwrt/issues/20566#issuecomment-3583555482
[3]: ASU proposal https://github.com/openwrt/asu/pull/1533
[4]: allow easy sysupgrade proposal https://github.com/openwrt/openwrt/pull/20947
[5]: b71f4665cd
Fixes: b71f466 ("mediatek: filogic: fix supported_devices list for gl-mt2500")
Fixes: 8d30e07 ("mediatek: filogic: fix for new GL.iNet GL-MT2500/GL-MT2500A hardware revision")
Fixes: https://github.com/openwrt/openwrt/issues/20566
Fixes: https://github.com/openwrt/asu/issues/1525
Signed-off-by: Mario Andrés Pérez <mapb_@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21842
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit 66a7e04e9e.
Doing so makes the u-boot unable to find the node for this pcie
controller and disable it on mx60, resulting boot failure, as reported
in https://github.com/openwrt/openwrt/issues/21649 .
If we keep on treating mx60 and mx60w the same target, we might have
to endure the warning which 66a7e04 wants to eliminate.
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/21941
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Only configure the eth0 MAC address when it is not already done in the
device tree. To do this, create a new variable "eth0_mac".
Also avoid setting "label_mac" for devices already having it defined in
the device tree.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/21644
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Explicitly specify all devices where the MAC address is configured based
on the U-Boot environment.
This change makes it clearer which devices use this method. Also makes
things simpler for any future devices which handle MAC address
configuration entirely via device tree.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/21644
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, the 02_network script always configures MAC addresses for
each individual LAN port unless "lan_mac_start" is set to "skip". This
behaviour can be unexpected, and is also somewhat broken, as it even
continues to do so when "lan_mac_start" is empty.
Change it to only do the configuration if "lan_mac_start" is non-empty,
and also remove the fallback to "lan_mac", making this more obvious and
less error-prone.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/21644
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The MAC address assignment for XikeStor SKS8300-8T and SKS8300-12E2T2X
is semantically identical to the first case, so let's combine them.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/21644
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is a missing tab in one of the cases of MAC address configuration.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/21644
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
patch netlink headers for netifd PSE support
& fix PSE backports for PSE Prio
The 626-* patches are backporting net PSE-PD from
linux 6.18 to 6.12. The 627-02 is a nearly verbatim
copy of the upstream commit. The 6.12-01 patches the
auto generated ethtool_netlink_generated header.
The 6.12 build tools do not have the build system
feature for generating the correct netlink
headers related to the backports.
Signed-off-by: Carlo Szelinsky <github@szelinsky.de>
Link: https://github.com/openwrt/openwrt/pull/21926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Upstream solution came with 6.4. Seems quilt refreshed it to the extent
that it basically gets applied twice.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21954
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
7e5b324 instance: check length of names when creating cgroups
014f94c procd: jail/cgroups: fix OOB write in cgroups_apply()
e08cdc8 hotplug-dispatch: fix filter disallowing setting PATH
afa4391 service instance: Improve handling of watchdog config changes
52c64d2 service instance: Fix overwriting of watchdog linked list members
96c827f coldplug: fix missing header include
6b10c71 hotplug-dispatch: fix missing header include
58d7aaa initd/coldplug: create /dev/null before running udevtrigger
64f97ff hotplug-dispatch: redirect output to /dev/null
c4e9859 hotplug-dispatch: use stat if d_type is DT_UNKNOWN
bafdfff system: fix arguments validation in ubus handler
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use the added support for generating per device targz rootfs so that images
generated for Methode devices when CONFIG_TARGET_MULTI_PROFILE and
CONFIG_TARGET_PER_DEVICE_ROOTFS are set, we actually get the targz rootfs
that respects DEVICE_PACKAGES.
Currently, buildbot generated images have no networking, LM75 nor I2C
working, as the generated images do not include required kmods that are
listed in DEVICE_PACKAGES.
While at it, there is no need for tar to run in verbose mode.
Fixes: 7dff6a8c89 ("mvebu: uDPU: add sysupgrade support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Currently, for targets that use the CONFIG_TARGET_ROOTFS_TARGZ a single
rootfs tarball is generated for the subtarget based of $(TARGET_DIR).
However, this means that it does not respect DEVICE_PACKAGES like other
rootfs images.
So, lets augment CONFIG_TARGET_ROOTFS_TARGZ by adding a proper targz fstype
so that per device rootfs is generated under lock.
This is required so that devices that use custom sysupgrade archives like
Methode devices, can actually include a per device rootfs so when building
for multiple devices and with CONFIG_TARGET_PER_DEVICE_ROOTFS set the built
image actually includes the listed DEVICE_PACKAGES.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Mikrotik RBM33G has got a USB-A port and mPCIe slots with USB 3.0 and USB
2.0 interfaces in use. The MediaTek MT7621 SoC has got an xHCI to provide
these interfaces. Therefore, enable kmod-usb3 to support them.
Fixes: 5684d08741 ("ramips: Add support for Mikrotik RouterBOARD RBM33g")
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
The bus reset functions currently configure a lot of things. Looking
closely they have a topology setup and a polling setup part. Split the
big chunk in smaller better readable functions.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21906
Signed-off-by: Robert Marko <robimarko@gmail.com>
The downstream Realtek phy module is currently known as rtl83xx-phy.c
and its kernel config REALTEK_SOC_PHY. It has been simplified, cleaned
and now aligns to Realtek main module (upstream Realtek phy). It is no
longer tied to the Realtek switch SoC but serves as generic module for
1Gbit multiport phys. Adapt it as follows:
- place it into the realtek folder aside its upstream sibling
- rename it to realtek_multiport.c
- remove SoC dependency in Kconfig and Makefile
- change kernel configs for the targets accordingly
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21929
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop some lines that are not needed any longer.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21929
Signed-off-by: Robert Marko <robimarko@gmail.com>
If nvmem is used for ethernet mac address, we need to defer loading to
get the proper mac.
Move to probe as ndo_init is the wrong place to handle EPROBE_DEFER.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21920
Signed-off-by: Robert Marko <robimarko@gmail.com>
When config_change is set during an active setup (e.g. by a concurrent
reconf call), wdev_mark_up() attempted to call setup() while still in
"setup" state. Since setup() requires state "up" or "down", it silently
returned, leaving the state as "setup". The subsequent wdev_setup_cb()
then treated this as a setup failure, triggering an unnecessary
teardown+restart cycle.
Fix this by removing the config_change handling from wdev_mark_up() and
moving it to wdev_setup_cb() instead. wdev_mark_up() now always
transitions to "up" state. When wdev_setup_cb() runs afterwards and
finds the device already "up" with config_change set, it initiates a
clean re-setup from the "up" state where setup() can run.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The Sophos SG/XG-125 revision 3 like the already supported SG/XG-135
revision 3 has odd numbering of eth ports where the WAN port (as marked
on the case) is: `eth6` and `eth0`, `eth1`, `eth2`, `eth3`, `eth5`, `eth7`,
`eth8` are LAN ports.
Port `eth4` confirmed to be the SFP port.
Signed-off-by: Raylynn Knight <rayknight@me.com>
Link: https://github.com/openwrt/openwrt/pull/21914
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Commit 01a87f4bd0 changed the encryption
setting of the default SSID "OpenWrt" from "none" to "open". The correct
setting as per the documentation [1] is "none", though.
While this invalid setting won't cause a wrong hostapd setup, it will
at least cause malfunction in LuCI.
Change the default encryption setting back to "none".
[1] https://openwrt.org/docs/guide-user/network/wifi/basic#encryption_modes
Fixes: 01a87f4bd0
Signed-off-by: Shine <4c.fce2@proton.me>
Link: https://github.com/openwrt/openwrt/pull/21925
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
meraki_loadaddr=1000000 may not enough to boot openwrt 25.12+ on mx60,
so directly sysupgrade without changing meraki_loadaddr would result
broken, but the u-boot-env partition used to be marked read-only, so
compat_version had better be incremented to show a notification to
direct users to the wiki to prepare the sysupgrade manually.
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/21912
Signed-off-by: Robert Marko <robimarko@gmail.com>
The main point of it currently is to extract mac addresses. That is not
being done as MAC addresses are elsewhere.
Disable it until it becomes more feature packed and there's an actual
use for it.
All devices already have config definitions. NVMEM prevents redundant
support as well as write support.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16618
Signed-off-by: Robert Marko <robimarko@gmail.com>
Needed to avoid probe errors.
There are two partitions from 0-20000 and 80000-100000.
This is redundant-count and not regular u-boot,env
Add status = "disabled" as the u-boot env driver can't handle redundant
environments properly. As a result, fw_printenv ends up not working
right.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16618
Signed-off-by: Robert Marko <robimarko@gmail.com>
Per the comments, this is not uboot,env but the redundant forms.
Placed under fixed-partition nodes in order to add status = "disabled".
The roots are needed for u-boot envtools to use.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16618
Signed-off-by: Robert Marko <robimarko@gmail.com>
With nvmem-layout, these probe errors go away.
Add status = "disabled" as the u-boot env driver can't handle redundant
environments properly. As a result, fw_printenv ends up not working
right.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16618
Signed-off-by: Robert Marko <robimarko@gmail.com>
With nvmem-layout, these probe errors go away.
Add status = "disabled" as the u-boot env driver can't handle redundant
environments properly. As a result, fw_printenv ends up not working
right.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16618
Signed-off-by: Robert Marko <robimarko@gmail.com>
These two are redundant definitions according to dts. A value of 4 (CRC
no redundancy) makes no sense.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16618
Signed-off-by: Robert Marko <robimarko@gmail.com>
There are two redundant sections. One at 0x0 and the other at 0x80000.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16618
Signed-off-by: Robert Marko <robimarko@gmail.com>
Code was moved from 601-ucode_support.patch into ucode.{c,h},
but the patch still contained the old hunks. As a result, the patch
no longer applies.
Fix this by dropping the moved code from 601-ucode_support.patch.
Fixes: a7756346c7 ("hostapd: extend DPP ucode API with WPS M7/M8 encrypted settings handling")
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add callbacks to intercept WPS M7 reception (registrar side) and M8
reception (enrollee side), allowing external code to inject extra
encrypted attributes and optionally skip credential building.
On the registrar side, the m7_rx callback receives the decrypted M7
content and can return extra data to include in M8's encrypted settings
as well as a flag to skip credential generation.
On the enrollee side, add a wps_set_m7 method to set extra encrypted
data for M7, and a m8_rx callback to handle the decrypted M8 content
externally.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
RTL930x and RTL931x basically share the same logic for mac_config().
No need to duplicate that logic in two functions and to call one
from the other.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21895
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is still a stray call in setup_serdes to read the current CMU
band. The only effect is that the current band is printed to the log, the
value itself isn't used for anything further. Drop this since it's not
needed.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21858
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
