Mesh mode interface creation fails when the freq parameter is empty or
undefined. Unlike adhoc mode which checks if freq exists before using it,
mesh mode blindly constructs the iw command with freq parameter, resulting
in invalid syntax like:
iw dev mesh0 mesh join ssid freq NOHT
This causes the mesh interface to be created without joining the mesh
network, leaving it in a DOWN state with no channel assigned.
Fix by adding freq validation check similar to adhoc mode.
Tested on two routers in parallel as mesh peers:
- Xiaomi AX3000T (MediaTek MT7981)
- OpenWrt One (MediaTek MT7981)
- OpenWrt 6.6.119, 802.11s mesh on 5GHz (Channel 36, HE80)
Signed-off-by: Valent Turkovic <valent@meshpointone.com>
Link: https://github.com/openwrt/openwrt/pull/21373
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7214acd759)
The for-in loop variable 'name' was shadowing the function parameter,
causing remote subscription cleanup to fail when hosts disconnect.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit e782341848)
This allows us to use the full size of nand,
which extends ubi size from 64Mb to 122.25Mb.
If you are at factory firmware, please refer
to [PR](https://github.com/openwrt/openwrt/pull/21141)
to boot into OpenWrt first.
1. Log in to the device and backup all the partitions,
especially unique `Factory` and `bdata` partitions
from System -> Backup / Flash Firmware -> Save mtdblock contents.
2. Install kmod-mtd-rw to unlock mtd partitions for writing:
```bash
apk update && apk add kmod-mtd-rw && insmod mtd-rw i_want_a_brick=1
```
3. Write new OpenWrt (U-Boot Layout) `BL2` and `FIP`:
```bash
mtd write openwrt-mediatek-filogic-cudy_wbr3000uax-v1-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cudy_wbr3000uax-v1-ubootmod-bl31-uboot.fip FIP
```
4. Set static IP on your PC: `192.168.1.254`, gateway `192.168.1.1`
5. Serve openwrt-mediatek-filogic-cudy_wbr3000uax-v1-ubootmod-initramfs-recovery.itb
using TFTP server.
6. Connect Router LAN with PC LAN.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt initramfs recovery has booted,
clean `/dev/mtd5` ubi partition to utilize maximum of free space & create ubootenvs:
```bash
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
```
4. Perform sysupgrade.
Tested-by: 4pda users
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21225
(cherry picked from commit 15df98f3b5)
Link: https://github.com/openwrt/openwrt/pull/21342
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Another OEM variation of a Cudy WR3000 series device made for Russian market.
Hardware:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB GigaDevice SPI NAND. Flash Model: F50L1G41LB, ID: C801
- RAM: DDR3, 512 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- 1x WAN MT7531 (JXD 2531Z) 10/100/1000 Mbps
- 4x LAN 2x MT7530 (JXD 2529S) 10/100/1000 Mbps
- USB 3.0 port
- Buttons: Reset, WPS
- 8x LEDs: 2x Red, 6x Blue
- Serial console: no need to solder, just open the case and unskrew the radiator, TX-RX, RX-TX, GND-GND, VCC do not connect, 115200 8n1
- Power: 12 VDC, 1.5 A
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:AF:CA:xx:xx:x1 | label+1 |
| LAN | 80:AF:CA:xx:xx:x0 | label |
| WLAN 2g | 80:AF:CA:xx:xx:x0 | label |
| WLAN 5g | 82:AF:CA:xx:xx:x1 | label+1 |
+---------+-------------------+-----------+
Based on a factory layout with only 64mb partition for easier transition from factory to OpenWrt for users if the "intermediate" RSA signed firmware will be provided by Cudy.
**Installation**
The installation must be done via UART & TFTP by disassembling the router. On other occasions Cudy has distributed intermediate firmware and dts to make installation easier, but since this router is OEM special WB order for local RU market there is a possibility they will not provide it.
**Install using UART & TFTP**
1. Connect to UART.
2. Since the factory BL is locked and the boot process can not be stopped, you have to use mtkuartboot, hold reset, engage the power, boot into your payloaded bl2 & fip.
3. Connect to LAN and set your IP to 192.168.1.254.
4. Configure a TFTP server to serve openwrt-mediatek-filogic-cudy_wbr3000uax-v1-initramfs-kernel.bin file.
5. Run these steps in u-boot using the name of your file:
```
setenv bootfile openwrt-mediatek-filogic-cudy_wbr3000uax-v1-initramfs-kernel.bin
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.254
tftpboot
bootm
```
6. Router will boot into OpenWrt initramfs recovery, just open your browser `192.168.1.1` and sysupgrade with the `Keep settings` option turned off.
Tested-by: many 4pda users
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21225
(cherry picked from commit d7d6faf26f)
Link: https://github.com/openwrt/openwrt/pull/21342
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since there are many similar devices from Cudy (TR3000 / WR3000E / WR3000P / WR3000S / WBR3000UAX) this will allow to create OpenWrt U-Boot layout for all of them using same DDR3 target.
Tested-by: 4pda users
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21225
(cherry picked from commit f4c9ab6591)
Link: https://github.com/openwrt/openwrt/pull/21342
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The GS110TUP's lan9 port is connected via a QSGMII PHY to SERDES 2, and
therefore should use the SWITCH_PORT_SDS macro instead of SWITCH_PORT. This
was missed in e956adfe because the GS110TUP is not particularly well
documented and the old code was confusing.
lan10 is an SFP and doesn't have an onboard PHY, so also remove its
associated PHY references and update it to match other devices' SFP ports.
Fixes: https://github.com/openwrt/openwrt/issues/21324
Signed-off-by: Jacob Potter <jacob@j4cbo.com>
Link: https://github.com/openwrt/openwrt/pull/21346
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b2c0182f26)
Inadvertently defining 'DEFAULT_VARIANT' on both ethool and
ethtool-full variants resulted in
$ make defconfig
tmp/.config-package.in:121615:error: recursive dependency detected!
tmp/.config-package.in:121615: symbol PACKAGE_ethtool-full is selected by PACKAGE_ethtool
tmp/.config-package.in:121605: symbol PACKAGE_ethtool depends on PACKAGE_ethtool-full
Fix this by simply undefining 'DEFAULT_VARIANT' on the ethtool-full
variant, which is ugly, but expedient.
Fixes: https://github.com/openwrt/openwrt/commit/f4fdb996
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21363
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 7a78dc4a5d)
Some packages with variants did not specify the default among the
alternatives, so were left without any apk 'provider_priority'
for that package. This caused the apk solver to select the wrong
variant, silently changing the requested package list.
Notable among these were busybox, procd and the hostapd/wpad suite.
This behavior presented in the imagebuilders when creating the
image as follows, silently replacing packages even when explicitly
requested:
$ make image PACKAGES=busybox
...
( 14/148) Installing busybox-selinux (1.37.0-r6)
...
We add 'DEFAULT_VARIANT:=1' to the packages that were missing one,
providing apk with sufficient information to choose the correct
package.
See link below for further examples and discussion.
Link: https://github.com/openwrt/openwrt/pull/21288#issuecomment-3704101422
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21358
(cherry picked from commit f4fdb9964a)
Link: https://github.com/openwrt/openwrt/pull/21355
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add an implicit self-provide to kmods. apk can't handle self provides,
be it versioned or virtual, so opt for a prefix and a suffix instead.
Package name without a prefix/suffix is too generic and might conflict
with other packages, e.g. wireguard. This allows several variants to
provide the same virtual package without adding extra provides to the
default one, e.g. r8169 implicitly provides kmod-r8169-any and is marked
as default, so r8125 can explicitly provide @kmod-r8169-any as well.
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/21288
(cherry picked from commit 9b37b7185c)
Link: https://github.com/openwrt/openwrt/pull/21355
Signed-off-by: Robert Marko <robimarko@gmail.com>
Allow defining virtual provides using the PROVIDES field by prefixing
them with @, e.g.:
PROVIDES:=@ca-certs
Virtual provides don't own the provided name and multiple packages with
the same virtual provides can be installed side-by-side. Packages must
still take care not to override each other's files.
Add an implicit self-provide to packages. apk can't handle self
provides, be it versioned or virtual, so opt for a suffix instead. This
allows several variants to provide the same virtual package without
adding extra provides to the default one, e.g. wget implicitly provides
wget-any and is marked as default, so wget-ssl can explicitly provide
@wget-any as well.
Filter out virtual provides when generating metadata.
Filter out virtual provides prefix and self provide where appropriate.
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/21288
(cherry picked from commit 5ed650acbf)
Link: https://github.com/openwrt/openwrt/pull/21355
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refactor provides logic into a helper define and use it for both apk and
control. Document the behavior.
Store preformatted provides in Package/$(1)/PROVIDES similar to defines.
Remove unnecessary logging.
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/21288
(cherry picked from commit cefbf1184f)
Link: https://github.com/openwrt/openwrt/pull/21355
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove unused pinctrl groups defined in the device tree, probably as a
result of importing the vendor device tree which is based on the
reference board from MediaTek's SDK.
114b5c2063 ("mediatek: filogic: Add support ASUS RT-AX57M")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 96205c99d01cf7f5e69f03ccdea790d0eb9ddb36)
Signed-off-by: Garrett Mesmer <garrettmesm@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21237
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ASUS RT-AX57M, RT-AX54HP V2, RT-AX1800HP V2, RT-AX1800S V2, and RT-AX3000S all use the same firmware and have identical hardware
Hardware
--------
SOC: MediaTek MT7981b
RAM: 256MB DDR3L (Winbond W632GU6NB-09)
FLASH: 128MB SPI-NAND (Winbond W25N01KVZEIR)
WIFI: Mediatek MT7981b + Mediatek MT7976DAN 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531AE Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
MAC addresses
-------------
LAN Label MAC (stored in mtd ubi Factory partition at offset 0x4)
WAN LAN
2.4G LAN + 2 in first octet
5G LAN
Installation
-----------------------------------------------------------
Vendor-UI Method
-----------------------------------------------------------
1. Download the OpenWrt initramfs.trx image.
2. Connect the PC via LAN to one of the yellow router ports and wait
until your PC to get a DHCP lease.
3. Browse to http://192.168.1.1 (or whatever your router IP is configured as)
4. If your router is brand new, finish the setup process and log into
the Web-UI.
5. Navigate to Administration -> Firmware Upgrade and upload the
downloaded OpenWrt initramfs.trx image.
6. Wait for OpenWrt to boot. Open the default OpenWrt IP in a web browser and perform a system upgrade using the sysupgrade image as instructed in the top banner.
---------------------------------------------------------------------------
Revert to stock firmware:
1: Install package facinstall -> https://forum.openwrt.org/t/facinstall-package-for-easy-installation-factory-images/177587
2. Install Asus stock trx image via OpenWRT LuCI interface.
Signed-off-by: Garrett Mesmer <garrettmesm@gmail.com>
Co-Authored-By: Oleg S <remittor@gmail.com>
Signed-off-by: Oleg S <remittor@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20491
(cherry picked from commit d09e2b1926a6009299eb034928df2c6b6b04dfa8)
Link: https://github.com/openwrt/openwrt/pull/21237
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The SUPPORTED_DEVICES sets for both Maxlinear (v1) and Airoha (v2)
devices were identical, so sysupgrade was unable to detect when an
incorrect image was being installed. This caused "soft bricking" of
devices when a v1 image was installed on a v2 device, and vice versa.
Fix this by making the supported_devices distinct for each device
version, by renaming the devices with a version-specific name.
This is reflected in the file name and the image metadata.
Fixes: https://github.com/openwrt/openwrt/issues/20566
Fixes: https://github.com/openwrt/asu/issues/1525
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20632
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b71f4665cd)
Wifi on the 6GHz band does not support open networks, configure owe by
default. 6GHz wifi also needs a country code, configure a broken country
code '00' by default to hint the user to change it.
Link: https://github.com/openwrt/openwrt/pull/21313
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 01a87f4bd0)
Without this patch, the
if (!config.wpa)
config.wpa_pairwise = null;
is overwritten immediately.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Link: https://github.com/openwrt/openwrt/pull/21215
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit bc4e7fd38e)
Changes:
* use upstream patches for airoha-snfi driver
* update in kernel en7523 dts to add spinand support
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/21299
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit d9b1c74780)
The EW71v2 has the WAN port configured at eth1.
The printed label-mac is configured on this iface in openwrt.
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
(cherry picked from commit 7f3537ee2c)
When wdev interfaces and hostapd interfaces are mixed, race conditions
can occur. Sometimes all interfaces are started correctly, sometimes only
the wdev interface and some of the hostapd interfaces, and sometimes only
the wdev interface.
Fix this by creating the wdev interfaces first, before processing
wpa_supplicant or hostapd interfaces.
Link: https://github.com/openwrt/openwrt/pull/21303
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit 2015a40c38)
RTL930x devices have highmem starting address at 0x20000000.
The Linksys LGS328C highmem definition is wrongly shared with
the larger LGS352C RTL931x model and starts at 0x90000000.
Fix it by splitting the definition.
Fixes: 853d73f ("realtek: add support for Linksys LGS328C")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5d7470d4ca)
Include XHCI USB drivers on the Cudy WR3000P v1 router, the drivers are
required to be able to use the USB port for USD devices.
Closes: https://github.com/openwrt/openwrt/issues/21231
Fixes: 04e9d154f2 ("mediatek: filogic: add support for Cudy WR3000P v1")
Signed-off-by: Dmitry Mostovoy <dmitry.mostovoy@ceifx.com>
Link: https://github.com/openwrt/openwrt/pull/21281
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 9da57e2f82)
This typo makes the script fail with:
-ash: /etc/hotplug.d/ieee80211/10_fix_wifi_mac: line 66: syntax error: unexpected word (expecting ")")
which ultimately prevents the mac address for certain devices wireless cards being set correctly
Signed-off-by: Nick French <nickfrench@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21287
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit cb94962ac4)
Add EHT* check so that the hwmode will display 802.11be capability correctly.
Signed-off-by: Elwin Huang <s09289728096@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21267
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit 95112a4939)
ipq5018 do not support freq scaling and therefore stuck on 800Mhz
This patch allows CPU to run with 1.008 Ghz as designed
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
Link: https://github.com/openwrt/openwrt/pull/21185
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit c1290fa48c)
Mesh interfaces may not define an encryption setting. This results in
a ucode runtime error when parse_encryption() is called:
Reference error: left-hand side expression is null
In parse_encryption(), file /usr/share/ucode/wifi/iface.uc, line 20, byte 32:
called from function setup_sta (/usr/share/ucode/wifi/supplicant.uc:59:31)
called from function generate (/usr/share/ucode/wifi/supplicant.uc:243:41)
called from function setup (./mac80211.sh:254:61)
called from anonymous function (./mac80211.sh:342:14)
` config.auth_type = encryption[0] ?? 'none';`
Near here ------------------------^
Link: https://github.com/openwrt/openwrt/pull/21293
(cherry picked from commit 00e6c18a93)
Link: https://github.com/openwrt/openwrt/pull/21295
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add menuconfig option 'kmod-usb-gadget-fs' for the USB FunctionFS gadget
module
OpenWRT is perfect for USB gadgets that are network-enabled, since it
provides everything needed to easily manage the device. Having support
for the FunctionFS gadget enables the use of any custom USB devices
that does not have a specific module, like Media Transfer Protocol.
Signed-off-by: Dominic Germain <dominic@germain.cc>
Link: https://github.com/openwrt/openwrt/pull/21207
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 22a69dfa4a)
The ncm proto handler ignored ip4table, ip6table, and mtu settings.
The fix is based on the existing code in the mbim proto handler.
Fixes: #20216.
Signed-off-by: Alexander Patrakov <patrakov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20217
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b289edd84b)
libc depends on knowing libgcc's ABI, so it needs to be evaluated first.
Otherwise libc will depend on an ABI-less libgcc causing the rest of the
toolchain to fail.
Building package index...
ERROR: unable to select packages:
libgcc (virtual):
note: please select one of the 'provided by'
packages explicitly
provided by: libgcc1
required by: world[libgcc]
Before:
libc fused dependencies: libgcc
libgcc fused dependencies:
libatomic fused dependencies: libgcc1
After:
libgcc fused dependencies:
libc fused dependencies: libgcc1
libatomic fused dependencies: libgcc1
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/21265
(cherry picked from commit 5e32bfbf4b)
Link: https://github.com/openwrt/openwrt/pull/21253
Signed-off-by: Robert Marko <robimarko@gmail.com>
The updated logic for the APK dependencies and provides is as follows:
- If ABI version is defined:
- package is named `package_name-ABI_version`
- package implicitly provides
`package_name-ABI_version=package_version`
this implies that only one version of a package per ABI can be
installed at the same time
- additionally provide `package_name` so multiple packages can be
looked up by its base name
- for each `provides`, provide `provide-ABI_version=package_version`
this implies that only one version of a provide can be installed at
the same time
- else if ABI version is _not_ defined
- package is named `package_name`
- package implicitly provides `package_name=package_version`
this implies that only one version of a package can be installed at
the same time
- if `alternatives` is defined
- for each `provides`, provide `provide`
this implies that multiple versions of a provide can be installed
at the same time
- else if `alternatives` is _not_ defined
- for each `provides`, provide `provide=package_version`
this implies that only one version of a provide can be installed
at the same time
Both cases a package can be looked up by its base name.
ABI version `alternatives`, `conffiles`, `conffiles_static`, `list` and
`rusers` files so multiple versions of the same ABI package can be
installed side by side, and so they don't overwrite each other's
packaging files.
ABI version `EXTRA_DEPENDS` so dependencies can be correctly looked up
using the existing OpenWrt semantics without the ABI specified. This is
needed since ABI-versioned libraries no longer provide
`package_name=package_version`, so that they can be installed side by
side.
Remove duplicate dependencies when `EXTRA_DEPENDS` specifies a versioned
one that is already in `DEPENDS`.
ABI is defined
------------------------------------------------------------------------
`libsqlite3` has `PROVIDES` set to `libfake` and has two different ABI
versions installed. `libfake` is just an example to demonstrate the
mechanics, as the library can already be depended upon using e.g.
`libsqlite3-0=3.51.0-r1`. Note the ABI-versioned lists.
```
root@OpenWrt:/tmp# apk add --allow-untrusted ./libsqlite3-0-3.51.0-r1.apk
(1/1) Installing libsqlite3-0 (3.51.0-r1)
libsqlite3-0-3.51.0-r1.post-install: Executing script...
OK: 22 MiB in 157 packages
root@OpenWrt:/tmp# apk add --allow-untrusted ./libsqlite3-1-4.00.0-r1.apk
(1/1) Installing libsqlite3-1 (4.00.0-r1)
libsqlite3-1-4.00.0-r1.post-install: Executing script...
OK: 23 MiB in 158 packages
root@OpenWrt:/tmp# apk query --fields name,version,contents,provides libsqlite3-0 libsqlite3-1
Name: libsqlite3-0
Version: 3.51.0-r2
Provides: libfake-0=3.51.0-r2 libsqlite3
Contents:
lib/apk/packages/libsqlite3-0.list
usr/lib/libsqlite3.so.0
usr/lib/libsqlite3.so.3.51.0
Name: libsqlite3-1
Version: 4.00.0-r1
Provides: libfake-1=4.00.0-r1 libsqlite3
Contents:
lib/apk/packages/libsqlite3-1.list
usr/lib/libsqlite3.so.1
usr/lib/libsqlite3.so.4.00.0
root@OpenWrt:/tmp# ls -lh /usr/lib/libsqlite3.so.*
lrwxrwxrwx 1 root root 20 Nov 20 00:23 /usr/lib/libsqlite3.so.0 -> libsqlite3.so.3.51.0
lrwxrwxrwx 1 root root 20 Nov 20 00:27 /usr/lib/libsqlite3.so.1 -> libsqlite3.so.4.00.0
-rwxr-xr-x 1 root root 1.0M Nov 6 18:19 /usr/lib/libsqlite3.so.3.51.0
-rwxr-xr-x 1 root root 1.0M Nov 6 18:19 /usr/lib/libsqlite3.so.4.00.0
```
ABI is not defined
------------------------------------------------------------------------
Both `avahi-dbus-daemon` and `avahi-nodbus-daemon` provide `avahi-daemon`,
but have no ABI specified. This results in `avahi-daemon=0.8-r11` provides
for both packages and only one being able to be installed at the same time:
```
root@OpenWrt:/tmp# apk add --allow-untrusted ./avahi-nodbus-daemon-0.8-r11.apk
(1/4) Installing libavahi-nodbus-support (0.8-r10)
libavahi-nodbus-support-0.8-r10.post-install: Executing script...
(2/4) Installing libdaemon (0.14-r5)
libdaemon-0.14-r5.post-install: Executing script...
(3/4) Installing libexpat (2.7.3-r1)
libexpat-2.7.3-r1.post-install: Executing script...
(4/4) Installing avahi-nodbus-daemon (0.8-r11)
avahi-nodbus-daemon-0.8-r11.post-install: Executing script...
23 MiB in 160 packages
root@OpenWrt:/tmp# apk query --fields provides avahi-nodbus-daemon
Provides: avahi-daemon=0.8-r11
root@OpenWrt:/tmp# apk add --allow-untrusted ./avahi-dbus-daemon-0.8-r11.apk
ERROR: unable to select packages:
avahi-dbus-daemon-0.8-r11:
conflicts: avahi-nodbus-daemon-0.8-r11[avahi-daemon=0.8-r11]
satisfies: world[avahi-dbus-daemon><Q1R111s+ke9Vf+eCxDHX2BZVUK54Q=]
avahi-nodbus-daemon-0.8-r11:
conflicts: avahi-dbus-daemon-0.8-r11[avahi-daemon=0.8-r11]
satisfies: world[avahi-nodbus-daemon><Q1BAu7nLI2MgRabpveLTGO2ksQz7E=]
```
Provides and alternatives
------------------------------------------------------------------------
Both `uclient-fetch` and `wget-nossl` provide `wget` and specify
alternatives, so provides are not versioned and both packages can be
installed at the same time:
```
root@OpenWrt:/tmp# apk query --fields name,version,contents,provides uclient-fetch wget-nossl
Name: uclient-fetch
Version: 2025.10.03~dc909ca7-r1
Provides: wget
Contents:
bin/uclient-fetch
lib/apk/packages/uclient-fetch.alternatives
lib/apk/packages/uclient-fetch.list
Name: wget-nossl
Version: 1.25.0-r1
Provides: gnu-wget wget
Contents:
lib/apk/packages/wget-nossl.alternatives
lib/apk/packages/wget-nossl.list
usr/libexec/wget-nossl
```
Fixes: https://github.com/openwrt/openwrt/issues/20582
Fixes: https://github.com/openwrt/openwrt/issues/20802
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/20819
(cherry picked from commit 18029977f6)
Link: https://github.com/openwrt/openwrt/pull/21253
Signed-off-by: Robert Marko <robimarko@gmail.com>
Interrupt vector for reo2host-status is wrongly assigned.
Status interrupts weren't received and a workaround was applied to
mac80211 to periodically poll the reo status ring. Therefore, the
workaround can be removed with the proper hardware interrupt line
assigned.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21272
Signed-off-by: Robert Marko <robimarko@gmail.com>
Sync the DTS with the version sent upstream, clock bindings also.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit bce8432bbd)
After merge of https://github.com/openwrt/openwrt/pull/20709 I noticed,
that https://mirror-03.infra.openwrt.org/snapshots/targets/ath79/tiny/
still does not contain the build for RE450.
I analyzed the problem and noticed, that only builds which fits into
original size can be build and if the image is larger, it fails with
the following error: "WARNING: Image file .../openwrt/build_dir/
target-mips_24kc_musl/linux-ath79_tiny/tmp/
openwrt-ath79-tiny-tplink_re450-v1-squashfs-sysupgrade.bin is too big:
> 7864320".
This error is quite misleading as the image is smaller than 7864320. The
reason for this error is that default tplink-safeloader has hardcoded
factory partition structure and fails to generate any file.
Rather then fixing tplink-safeloader I followed approach from commit
ebd5e5fb53 ("ramips: switched TP-Link RE305 v1 to new partition layout")
and switched away from "tplink-safeloader sysupgrade".
I did not include "IMAGES := sysupgrade.bin", because with tiny target it
is still possible to locally build even factory image.
Fixes commit e768731dc8 ("ath79: switch TP-Link RE355 v1, RE450 v1 and
RE450 v2 to mtd-concat").
Signed-off-by: Radek Dostál <rd@radekdostal.com>
Link: https://github.com/openwrt/openwrt/pull/21158
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit bdbb4bdfa0)
Popular cheap PWM fans for this machine, like the ones coming in
heatsink+fan combos will not work properly at the currently defined
medium speed. Trying different pwm setting using a command
echo $value > /sys/devices/platform/pwm-fan/hwmon/hwmon1/pwm1
I found:
pwm1 value fan rotation speed cpu temperature notes
-----------------------------------------------------------------
0 maximal 31.5 Celsius too noisy
40 optimal 35.2 Celsius no noise hearable
95 minimal
above 95 does not rotate 55.5 Celsius
-----------------------------------------------------------------
Current cooling levels are:
cooling-levels = <255 96 0>;
Thus only cpu-active-high and cpu-active-low modes are usable.
This patch fixes cpu-active-medium settings for bpi-r3 board.
This patch may not be enough. Users may wants to tweak their thermal_zone0
trip points, thus tuning fan rotation speed depending on cpu temperature.
That can be done on the base of the following example:
=== example =========
# cpu temperature below 25 Celsius degrees, no rotation
echo 25000 > /sys/class/thermal/thermal_zone0/trip_point_4_temp
# cpu temperature in [25..32] Celsius degrees, normal rotation speed
echo 32000 > /sys/class/thermal/thermal_zone0/trip_point_3_temp
# cpu temperature above 50 Celsius degrees, max rotation speed
echo 50000 > /sys/class/thermal/thermal_zone0/trip_point_2_temp
=====================
Changes v2:
* put patch to a proper directory
* updated patch description
* tested with latest openwrt based on linux-6.6
Changes v3:
* use upstream linux patch
* update patch description
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17130
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 095151b235)
