The version of libxml2 was bumped from 2.13.6 to 2.14.5. Since version
2.14, libxml2 is not binary compatible with older versions. Therefore
add an abi version.
From the NEWS file:
Binary compatibility is restricted to versions 2.14 or newer. On ELF
systems, the soname was bumped from libxml2.so.2 to libxml2.so.16.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Link: https://github.com/openwrt/openwrt/pull/19983
(cherry picked from commit 420be05d90)
Link: https://github.com/openwrt/openwrt/pull/19985
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3GHz
- RAM : DDR3 256Mbytes, ESMT M15T2G16128A
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976CN dual-band Wi-Fi 6
- 2.4GHz : b/g/n/ax, MU-MIMO
- 5GHz : a/n/ac/ax, MU-MIMO
- Ethernet : MediaTek MT7531AE
- LAN : 10/100/1000 Mbps x4
- WAN : 10/100/1000 Mbps x1
- UART : 1x4 pin header on PCB
- [J6] TX, RX, GND, 3.3V (115200, 8N1)
- Buttons : WPS, Reset
- LEDs : 1x CPU (Amber)
1x Wi-Fi 5GHz (Amber)
1x Wi-Fi 2.4GHz (Amber)
1x WAN activity (Amber)
4x LAN activity (Amber)
- Power : 12VDC, 1A (Center positive polarity)
MAC address
-----------
+-----------+-------------------+-----------------------+
| Interface | MAC | Algorithm |
+-----------+-------------------+-----------------------+
| WLAN 2.4G | B0:38:6C:48:xx:xx | label |
| WLAN 5G | B2:38:6C:48:xx:xx | label with LA Bit Set |
| WAN | B0:38:6C:48:xx:xx | label + 1 |
| LAN | B0:38:6C:48:xx:xx | label + 3 |
+-----------+-------------------+-----------------------+
The WLAN 2.4G MAC was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router(keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router(LAN port) to the PC
6. Replace a file in the OEM recovery software with the file from step 2
7. Run the OEM recovery software and follow the instructions
8. Wait for the router to boot from *squashfs-factory.bin
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19368
(cherry picked from commit aea6d1bf5e)
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes compilation of the vmmc driver, it uses these functions.
Fixes: c676281e7e ("kernel: bump 6.6 to 6.6.103")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is a variant of the Radxa ROCK Pi E v3 equipped with the Realtek
RTL8821CU. Add the kmod-rtw88-8821cu package for it.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/18310
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit f13ddfb0cf)
Link: https://github.com/openwrt/openwrt/pull/19940
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 4SE[1] is a single board computer using the Rockchip
RK3399-T.
Hardware
--------
- Dual-core Cortex-A72 and quad-core Cortex-A53 CPU
- Mali-T860MP4 GPU
- LPDDR4 4GB RAM
- M.2 M Key slot (PCIe 2.1 x4)
- eMMC connector
- microSD card slot
- Wi-Fi 5 (not supported)
- Gigabit Ethernet with PoE support (additional PoE HAT required)
- USB 3.0 Type-A OTG port
- USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- USB Type-C power port (5V only)
- 40 Pin GPIO header
[1] https://radxa.com/products/rock4/4se
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to the micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/17554
(cherry picked from commit 6690f551c8)
Link: https://github.com/openwrt/openwrt/pull/19940
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 4C+[1] is a single board computer with dual HDMI using
the Rockchip RK3399-T.
Hardware
--------
- Dual-core Cortex-A72 and quad-core Cortex-A53 CPU
- Mali-T860MP4 GPU
- LPDDR4 4GB RAM
- eMMC connector
- microSD card slot
- Wi-Fi 5 (not supported)
- Gigabit Ethernet with PoE support (additional PoE HAT required)
- USB 3.0 Type-A OTG port
- USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- USB Type-C power port (5V only)
- 40 Pin GPIO header
[1] https://radxa.com/products/rock4/4cp
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to the micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/17554
(cherry picked from commit 18925614c0)
Link: https://github.com/openwrt/openwrt/pull/19940
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adds the capability to flash the factory image using the OEM recovery
software, ipTIME Firmware Wizard(11ac).
Installation
------------
1. Download the OEM recovery software from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router(keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router(LAN port) to the PC
6. Run the OEM recovery software and follow the instructions
7. Select the *squashfs-factory.bin file during the router recovery process
8. Wait for the router to boot from *squashfs-factory.bin
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19497
(cherry picked from commit 0e4a69e340)
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19928
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport a patch from upstream kernel 6.17-rc4 which fixes a regression
introduced in the latest stable kernel versions.
This is already in the Linus stable queues for the next minor kernel
updates.
Fixes: 1c92e468d5 ("kernel: bump 6.6 to 6.6.103")
Fixes: f39c7e103f ("kernel: bump 6.12 to 6.12.43")
Reported-by: Goetz Goerisch <ggoerisch@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit c589fb7baf)
8b320f9 ucode: adjust for new ext resource type
e61d2be sys: use strstr() to detect installed packages
bba9519 rpc-sys: packagelist: don't truncate input lines on read
The removed patch was applied upstream.
Link: https://github.com/openwrt/openwrt/pull/19919
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When sending llc packets with vlan tx offload, the hardware fails to
actually add the tag. Deal with this by fixing it up in software.
Fixes: https://github.com/openwrt/openwrt/issues/19916
Reported-by: Thibaut VARENE <hacks@slashdirt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit f7d4036555)
075cdc0 iptime-crc32: add support for ipTIME AX3000Q
48ababa iptime-crc32: add support for ipTIME AX3000SM
f29de74 iptime-crc32: Add device support for ipTIME AX6000M
Link: https://github.com/openwrt/openwrt/pull/19520
(cherry picked from commit b087961ccb)
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19915
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
RTL83xx devices have two types of receive interrupts for each of its
8 rings. One for packet received and another for ring overflow. When
the switch is flooded with incoming packets the receive handler will
disable the packet receive notification but still keeps the overflow
notification enabled. While the receive path "slowly" processes the
received packets each new packet triggers the overflow IRQ again. The
device becomes unresponsive and eventually produces messages like:
[18441.709764] rcu: Stack dump where RCU GP kthread last ran:
[18441.727892] Sending NMI from CPU 1 to CPUs 0:
[18441.742300] NMI backtrace for cpu 0 skipped: idling at 0x8080e994
[18415.251700] rcu: INFO: rcu_sched detected stalls on CPUs/tasks:
[18415.271350] rcu: 0-...!: (0 ticks this GP) idle=d740/0/0x0 ...
[18415.303046] rcu: (detected by 1, t=6004 jiffies, g=230925, ...
[18415.326095] Sending NMI from CPU 1 to CPUs 0:
[18415.340540] NMI backtrace for cpu 0
Fix this issue by always disabling receive and overflow interrupts at
the same time.
Test with hping3 --udp -p 5021 -d 1400 --flood 192.168.2.72
Before (3sec run):
[183260.324846] rtl838x-eth 1b00a300.ethernet eth0: RX buffer overrun: status 0x101, mask: 0x7ffeff
[183260.340524] rtl838x-eth 1b00a300.ethernet eth0: RX buffer overrun: status 0x1, mask: 0x7ffeff
[183260.345799] net_ratelimit: 489997 callbacks suppressed
After (3 sec run):
[ 373.981479] rtl838x-eth 1b00a300.ethernet eth0: rx ring overrun: status 0x101, mask: 0x7fffff
[ 374.031118] rtl838x-eth 1b00a300.ethernet eth0: rx ring overrun: status 0x101, mask: 0x7fffff
[ 377.919996] net_ratelimit: 34 callbacks suppressed
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19365
(cherry picked from commit 963ee6ac3f)
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19891
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The IgniteNet SunSpot AC Wave2 comes with 2x QCA9994 ath10k chips
connected to the IPQ8068 SoC via PCIe.
Add board-2.bin for both radios on this board.
3ac4a64 qca9984: add BDFs for IgniteNet SS-W2-AC2600
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit d8303b4721)
Link: https://github.com/openwrt/openwrt/pull/19902
[Do not add ignitenet_ss-w2-ac2600]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We have modified the kernel to setup all "default" consoles,
including serial ports and framebuffers/screens, providing
no console= argument is supplied on the kernel command line.
Adding 'console=tty1' caused the 'default' serial port on
device tree systems to break, as the kernel would not carry
over the settings (like baud rate) from the bootloader.
The system administrator can still force the use of a
specific console by adding their own console= arguments.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Fixes: c099523d66 ("armsr: use console=tty1 to make
console more readily available")
Link: https://github.com/openwrt/openwrt/pull/17012
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit bff179de73)
Link: https://github.com/openwrt/openwrt/pull/19894
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
A previous change added 'console=tty1' to the default kernel command
line on armsr, in order to ensure the framebuffer console is enabled
on systems capable of graphics output.
Unfortunately, this change broke boards that used device tree
(DT) firmware with serial consoles, as the serial console
specified by the system firmware (stdout-path) was no longer
setup by the kernel.
A bit of probing determined that the SPCR (serial port console
direction table) on ACPI systems was preventing Linux from setting
up a default framebuffer console on these systems (which is why
console=tty1 was added).
(The affected ACPI systems are usually VMs using QEMU's
'virt' machine and EDK2 firmware. The firmware on these systems
does not remove the SPCR when a screen is present)
So to ensure all possible systems are setup correctly, we modify
the kernel so all "default" console types (serial and screen)
are setup when no console= arguments are specified on the kernel
command line.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Fixes: c099523d66 ("use console=tty1 to make console more
readily available")
Link: https://github.com/openwrt/openwrt/pull/17012
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3697022ce3)
Link: https://github.com/openwrt/openwrt/pull/19894
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6e4ffe2c6657 ucode: add function for getting the number of entries in a snapshot
a62edd89255b ucode: add support for fetching kernel tracepoint events
edeb4d6dc690 udebug-cli: add support for streaming tracing data
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 78188ee2bc)
3d953628bf17 udebugd: add support for setting an override config
93f6df0240e5 udebug-cli: add support for overriding config on the command line
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit c4e7b9b9b7)
The vendor DTS defined incorrect GPIOs for the LEDs, which caused them
to not function properly. Initially, the WAN, WLAN LEDs appeared to
work, but further testing showed that they were non-functional.
This patch corrects the GPIO assignments in the DTS, restoring full LED
functionality including blinking, except the power LED which cannot be
software controlled.
Tested on a CF-EW71 v2 unit.
Fixes: ee3a6adc6c ("ath79: add support for Comfast CF-EW71 v2")
Signed-off-by: Felix Golatofski <git@xdfr.de>
Link: https://github.com/openwrt/openwrt/pull/19665
(cherry picked from commit 9ce23ac840)
Link: https://github.com/openwrt/openwrt/pull/19839
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This enables software that requires this cipher suite (e.g. OpenThread Border
Router) to be compiled against the shared library rather than a separate copy.
Signed-off-by: Karsten Sperling <ksperling@apple.com>
Link: https://github.com/openwrt/openwrt/pull/19489
(cherry picked from commit 97dc9f8dbf)
Link: https://github.com/openwrt/openwrt/pull/19839
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
