Backport a patch fixing a kernel panic on airoha_hw_init fail. This
should better handle scenario with NPU load Probe deferring.
(cherry picked from commit c3c75d0e68)
[ fix conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport cleanup patch for Airoha Ethernet patch to permit easier
backport in the future.
Automatically refresh all affected patch.
(cherry picked from commit 2f3ea18f91)
[ fix conflict errors, drop upstream patch ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Airoha AN7581 eMMC RFB board mount 2 Aeonsemi AS21xxx PHY. One is
usually connected to GDM4 and the other is optionally connected to GDM2.
Add the relevant nodes to support the one connected to GDM4.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 26da4bf552)
Pack the BL2 and BL31+U-Boot artifacts as Airoha AN7581 is currently
supported in upstream U-Boot and bootloader files can be used for
unfused boards.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 17cb69fe7f)
Backport additional patch required for NPU support of Airoha AN7583.
These are specific for the NPU module with some minor fixes and to adds
upport for loading the specific Airoha AN7583 NPU firmware.
(cherry picked from commit 8b4adfbb87)
[ fix conflict errors ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add relevant nodes for NPU support for Airoha AN7583 and enable the
kernel config to enable support in the Airoha Ethernet driver.
NPU firmware is scheduled to be upstreamed to linux-firmware and will be
added once present upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 8758b58f25)
Fix the current image Makefile for Airoha AN7583 by dropping the
artifacts entry for bootloader and add default PKG for the PHY mounted
on the RFB boards.
The artifacts for the bootloader will be readded later once ATF-A
support will be pushed mainline.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a7964f0893)
While adding support for Airoha AN7583, it was forget to push the EMMC
DTS while defining the variant in the image Makefile.
Add the missing DTS to fix image creation error.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 6fe65d404b)
On the Airoha AN7583 EVB there are 2 Aeonsemi AS21xxx PHY but only the
one connected to Serdes Ethernet is usable as the other connected to
Serdes PON is not actually HW connected (as the serdes is connected to
the BOSA port)
Add comments and disable the relevant PHY.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit ea850b5a18)
Backport upstream patch for AN7583 Ethernet support. While at it also
backport some additional fixes required to apply the AN7583 patches
cleanly.
Refresh all affected patch automatically (aside from the XSI patch that
changed the implementation)
Link: https://github.com/openwrt/openwrt/pull/20489
(cherry picked from commit 46a454fb9b)
[ fix conflict errors ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add missing syscon compatible for scuclk node.
Fix the unit-address of the scuclk node.
This fixes the pcs driver error:
airoha-pcs 1fa08000.pcs: probe with driver airoha-pcs failed with error -22
airoha-pcs 1fa09000.pcs: probe with driver airoha-pcs failed with error -22
Fixes: c3d70b1 ("airoha: en7581: Add support for external PHY")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20190
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a30daf8a0b)
All devices under airoha use dts directory under the target,
so update the default DEVICE_DTS_DIR. Also set the default
DEVICE_DTS based on the SoC name for non-dev boards.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20190
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 866c4e5cdf)
Introduce initial support for Airoha AN7583 SoC and add all the required
patch for basic functionality of the SoC.
Airoha AN7583 is based on Airoha EN7581 SoC with some major changes on
the PHY handling and Serdes. It can be see as a lower spec of EN7581
with modern and simplified implementations.
All the patch are sent upstream and are pending revision. Support for
PCIe and USB will come later as soon as DT structure is accepted
upstream.
(cherry picked from commit c5b12fc02a)
[ fix conflict errors, add MDIO_AIROHA config ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This add a pending version of the Airoha PCS driver to add support for
External PHY. The Airoha PCS driver will receive some minor modification
once we the PCS subsystem will be defined upstream.
Add all the required node for GDM2 and GDM4 and enable the PCS config.
(cherry picked from commit c3d70b1ae5)
[ fix conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
No functional changes intended.
Fixes warning:
/linux/arch/arm64/boot/dts/airoha/en7581-gemtek-w1700k.dtb: i2c1@1fbf8100 (mediatek,mt7621-i2c): status: 'oneOf' conditional failed, one must be fixed:
['disable'] is not of type 'object'
'disable' is not one of ['okay', 'disabled', 'reserved', 'fail', 'fail-needs-probe']
from schema $id: http://devicetree.org/schemas/dt-core.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20131
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3872e9d317)
The baud rate control on Airoha does not function properly. This
patch enables the inactive code responsible for this. The UART2
baud rate is correct. HSUART3 operates at twice the requested
baud rate. The same problem exists in the current code, so this
doesn't introduce any regression. Support for baud rates higher
than 460800 is still required. This will be added in the future.
Tested on Gemtek W1700k. UART2 and HSUART3 are working fine.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20049
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 440b85f5b1)
[ solve conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport fixes for Airoha pinctrl driver for PHY LED and MDIO bus. This
fix a copy-paste error for PHY LED and a misconfiguration for MT7530
embedded Switch MDIO bus GPIO pin to permit usage of external PHYs.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 35ff70e807)
Add the NPU and reserved memory node for AN7581 dtsi since it's not
supported.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3dca527e6d)
Major backport of upstream patch for support of multiple feature of the
Airoha Ethernet driver.
Feature backported are TSO, Jumbo packet, Offload and initial Wlan
Offload support.
Link: https://github.com/openwrt/openwrt/pull/19816
(cherry picked from commit 9d3009f426)
[ add missing kconfig flag ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport trivial fixes from upstream related to pinctrl and ethernet
driver.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 354d7472d5)
Backport patch adding support for AN7581 Ethernet PHY based on the same
Mediatek embedded Switch PHY.
Link: https://github.com/openwrt/openwrt/pull/19816
(cherry picked from commit 0adaeff5ee)
[ rework backported patch ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace thermal patch with upstream version. The thermal maintainer
reported that the sysfs entry are considered deprecated and that slope
and offset should be handled internally to the driver.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a713260966)
This board is also as known as E-Life ETR631-T/ETR635-U.
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Uncompress the configuration:
* Enter fakeroot if you are not login as root.
tar -zxf <filename>.tar.gz
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; telnetd; ) &
5. Repack the configuration:
tar -zcf backup.tar.gz etc/
6. Upload new configuration via web interface, now you can connect to
KOMI A31 via telnet.
Flash instructions:
1. Connect to KOMI A31, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-konka_komi-a31-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-konka_komi-a31-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20357
(cherry picked from commit 8a7de107d8)
[rebase uboot patches upon 24.10 branch]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20595
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
RockChip RK3568 ARM64 (4 cores)
1/2GB LPDDR4 RAM
2x 2500 Base-T (PCIe, r8125b)
1 LED (Power)
1 Button (Reset)
Micro-SD Slot
2x USB 3.0 Port
12V DC Jack
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card using
dd.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19990
(cherry picked from commit d76a774270)
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20618
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for the Lunzn FastRhino R66S board.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19990
(cherry picked from commit 678536740e)
[rebase patches upon 24.10 branch]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20618
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The High-Speed SD mode stability issue should have been fixed.
Increase the MMC max-frequency to improve the IO speed. We can
still use the sysfs to limit the clock frequency, e.g.
root@OpenWrt:~# echo 25000000 > /sys/kernel/debug/mmc0/clock
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18896
(cherry picked from commit 143cfd6113)
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20258
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The MT7628 programing guide shows that the correct DTOC unit is
1048576 clocks instead of 65536 clocks. This value is also used
by linux upstream mtk-sd driver. Correct the DTOC register and
also round up its value.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18896
(cherry picked from commit e69c867cdf)
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20258
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- Fix MMC bus IO voltage. The GPIO voltage of mt762x series SoCs
is fixed 3.3V. There are no visible registers that can control
the voltage level. Also add "no-1-8-v" property to indicate that
MMC controller doesn't support 1.8V IO.
- Drop useless property "enable-active-high". These dummy fixed
voltage regulators are not controlled by the GPIO. We don't need
to set the GPIO polarity.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18886
(cherry picked from commit afdf88b9a1)
[rebased upon 24.10 branch]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20258
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If the environment variable `CI` is set, ccache will enable the CMake
option CCACHE_DEV_MODE by default. This leads to differing behaviour
between local and CI builds which takes quite some time to debug. 🤯
Achieve consistent behaviour between local builds and CI builds by
setting CCACHE_DEV_MODE. Set it to OFF, because CCACHE_DEV_MODE amongst
other settings like linker choice, enables -Werror, which will lead to
potential compilation failures when the host compiler is updated. Using
-Werror for host utils is not desirable, because the compiler version
used is not controlled by the OpenWrt build system and host utils should
compile successfully on an as wide range of host OSes as possible.
Reported-by: Roman Azarenko <roman.azarenko@iopsys.eu>
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20290
(cherry picked from commit 6f32c657db)
Link: https://github.com/openwrt/openwrt/pull/20334
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Mold does not really work on MacOS, when attempting to use it for example
for ubus:
mold: get_self_path is not supportedcollect2: error: ld returned 1 exit status
Which was introduced by [1] so it seems that MacOS is not supported, so
lets make it non selectable when MacOS is the host.
[1] f9a37e9dd4
Link: https://github.com/openwrt/openwrt/pull/18575
(cherry picked from commit 3c65dc3678)
Link: https://github.com/openwrt/openwrt/pull/20621
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that we have a board file, add calibration variant for TP-Link
Archer C60 v2 and add ipq-wifi package for it.
Tested-by: Semih Baskan <strstgs@gmail.com>
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20496
Link: https://github.com/openwrt/openwrt/pull/20497
Signed-off-by: Robert Marko <robimarko@gmail.com>
With further investigation it was found a race in generating .itb images
that include a RootFS caused by the mkits.sh and the mkimage.
Due to the fact that mkits.sh generates a .pagesync image of the passed
rootfs, it can happen that, concurrently, mkimage can be called at the
same time mkits.sh is creating another .pagesync for the same rootfs.
This cause mkimage to use an half made rootfs.pagesync creating a
corrupted image.
To address this, also protect the mkimage with the same lock used for
mkits.sh preventing any kind of concurrent usage/generation of the
rootfs.pagesync blob
Fixes: 52cc9d82f1 ("kernel: rework Initramfs locking logic")
Link: https://github.com/openwrt/openwrt/pull/20492
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3de1bbd5ae)
Currently, building at91 subtargets via image builder will fail as the
required built at91bootstrap is not present in the image builder at all
since its presumed to be in the binary directory which obviously does not
exist yet.
So, lets install the at91bootstrap binary into image staging directory and
use that instead
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a947be41b7)
Currently, building at91 subtargets via image builder will fail as the
required built u-boot is not present in the image builder at all since its
presumed to be in the binary directory which obviously does not exist yet.
So, lets install the u-boot binary into image staging directory and use
that instead.
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 4724331d70)
Currently, kmod-usb-ohci,kmod-at91-udc and kmod-usb-gadget-eth are included
as the default packages for all at91 subtargets.
However, this is breaking image builder as kmod-at91-udc is not being built
on sama7 since it depends on USB_SUPPORT and sama7 does not have USB support
enabled in the kernel as its not supported upstream so its not even
selectable in the config.
So, move to include these as default packages only for sama5 and sama9x as
both of those have USB support enabled.
Fixes: #18407
Link: https://github.com/openwrt/openwrt/pull/18413
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 02d3aa72bb)
Now that all packages that relied on the skip mechanism are selected
via BUILD_DEVICES or by defaulting for the subtarget drop them from
individual DEVICE_PACKAGES so that Image Builder works again for armv7.
Fixes: #18411
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8cb7919a13)
Currently, ls-rcw package is being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in:
377b66990b ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~ls-rcw' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the ls-rcw package in DEVICE_PACKAGES lets select it when
layerscape/armv7 target is selected.
Fixes: #18411
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 598a0556b7)
