Backport upstream patch to add support for the ESMT F50L1G41LC flash
chip. It is used in multiple Cudy products manufactured starting
November 2025.
(cherry picked from commit 9424b2b786)
Link: https://github.com/openwrt/openwrt/pull/20963
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In implementing APK support it seems a a leftover was never removed that
creates an unused tmp directory in the package feed directory.
Drop it as it's not used anywhere. What is actually needed is the
creation of the $$(PDIR_$(1)) directory for the feed package directory
in the bin/packages directory.
This was a side effect of using INSTALL_DIR on $$(PDIR_$(1))/tmp that
indirectly creates the $$(PDIR_$(1)) parent directory.
Fixes: d788ab376f ("build: add APK package build capabilities")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit f9802d70c6)
Airoha AN7581 SoC supports a Network Processor (NPU) to offload WiFi
traffic. Add the required bits to enable the support of it in the MT76
driver. This will be enabled by default if we are compiling for the
Airoha AN7581 SoC.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
[ improve commit title/description ]
Link: https://github.com/openwrt/openwrt/pull/20826
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 79d418eed8)
0aece3089a3a wifi: mt76: mt7996: Remove useless check in mt7996_msdu_page_get_from_cache()
05b3d899ad24 wifi: mt76: Move Q_READ/Q_WRITE definitions in dma.h
85e6517b0ac5 wifi: mt76: Add mt76_dev pointer in mt76_queue struct.
a3b6c67c97d2 wifi: mt76: Add the capability to set TX token start ID
141a81557070 wifi: mt76: Introduce the NPU generic layer
647d11bb17e0 wifi: mt76: mt7996: Add NPU offload support to MT7996 driver
8ff3b2bfc37f wifi: mt76: mt7996: fix typos in comments
0043147439b4 wifi: mt76: mt7925: refactor regulatory domain handling to regd.[ch]
f0e8fe441489 wifi: mt76: mt7925: refactor CLC support check flow
588cc87bf6a2 wifi: mt76: mt7925: refactor regulatory notifier flow
dac1d45fe94b wifi: mt76: mt7925: improve EHT capability control in regulatory flow
c166c4a0e750 wifi: mt76: mt7925: add auto regdomain switch support
d7b059bba166 wifi: mt76: mt7925: disable auto regd changes after user set
84f62a6beb99 wifi: mt76: mmio_*_copy fix byte order and alignment
f5ae5b2e8116 Revert "wifi: mt76: mt792x: improve monitor interface handling"
8ae7e6dc1d3a wifi: mt76: adjust BSS conf pointer handling
1b438ebe0d06 wifi: mt76: mt7925: cqm rssi low/high event notify
7519fa4ce62c wifi: mt76: mt7996: fix max nss value when getting rx chainmask
ea0580ad065f wifi: mt76: mt7996: no need to wait ACK event for SDO command
74112c2956fb wifi: mt76: mt7996: fix implicit beamforming support for mt7992
361d6bdac45d wifi: mt76: mt7996: support fixed rate for link station
d99274cdc30c wifi: mt76: mt7996: fix several fields in mt7996_mcu_bss_basic_tlv()
ad90a85b652b wifi: mt76: mt7996: fix teardown command for an MLD peer
e9fe8bc03e41 wifi: mt76: mt7996: set link_valid field when initializing wcid
050394665502 wifi: mt76: mt7996: use correct link_id when filling TXD and TXP
5d223855552c wifi: mt76: mt7996: fix MLD group index assignment
ab8361dbc421 wifi: mt76: mt7996: fix MLO set key and group key issues
7ce7ab881b3f wifi: mt76: mt7996: fix using wrong phy to start in mt7996_mac_restart()
1e0c23ff754b wifi: mt76: mt7996: fix EMI rings for RRO
eb567bc7f9b6 wifi: mt76: mt7925: ensure the 6GHz A-MPDU density cap from the hardware.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit e1a584b5d2)
Some Marvell AP firmware used with mwl8k misbehaves when beacons do not
contain the DSSS Parameter Set (WLAN_EID_DS_PARAMS) with the current
channel. When hostapd/mac80211 omits this element (which is valid on
some bands), the firmware may report bogus RX channel information and AP
mode becomes unusable.
Backport the upstream fix that ensures beacons always carry the DSSS
Parameter Set for mwl8k: when setting the beacon, detect if the element
is missing and inject it after SSID and Supported Rates (per spec
ordering). This mirrors behaviour in newer Marvell drivers and restores
stable operation.
Tested on Linksys EA4500 (88W8366).
Fixes: openwrt/openwrt#19088
Link: https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless.git/commit/?id=c4e1ac09ee1c750890e36cb1f841f25518f23589
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20757
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 38ed1510db)
[refreshed patches]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20817
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Since we are not using patch -b, *.orig files are only created when
there are conflicts, or never according to posix patch.
As such, it doesn't really make sense to always delete *.orig files
presuming they are patch backups, even if they are patch backups.
Doing so is both deleting potentially useful information for failed
patch applications and creating hard to diagnose bugs [1].
In a similar vein, checking for *.rej files does not add any value
since we're already checking the patch command's return code.
[1]: https://github.com/openwrt/packages/issues/27485
Signed-off-by: George Tsiamasiotis <george@tsiamasiotis.gr>
Link: https://github.com/openwrt/openwrt/pull/20141
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 75ca6bafd6)
Link: https://github.com/openwrt/openwrt/pull/20742
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
When building in environments that set IS_TTY, the feeds script does not
honor it and passes a hardcoded value to scan.mk, causing unwanted
control characters to appear in stdout.
This commit addresses the issue by checking IS_TTY and MAKE_TERMOUT
variables and uses their values if defined.
Closes#8039
Signed-off-by: Ernestas Kulik <ernestas.k@iconn-networks.com>
Link: https://github.com/openwrt/openwrt/pull/20743
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit fd7e43d429)
Backport upstream patch fixing out of order DMA access for ethernet
driver. This is relevant in the context of QoS when packets doesn't
follow linear handling by QDMA HW.
(cherry picked from commit 3169ffa4c7)
[ fix conflict errors ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
A new function "get_linux_version()" to normalize and print the
kernel version as an integer. In some migration scripts, it is
useful for checking the Linux kernel version.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit a0fe3cfb62)
Link: https://github.com/openwrt/openwrt/pull/20739
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
KConfig flag have an extra whitespace for CONFIG_PHY_AIROHA_USB and
value is not ignored.
Drop the extra whitespace to correctly ignore the value on kernel
compilation.
Fixes: c5b12fc02a ("airoha: Introduce support for Airoha AN7583 SoC")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit eedc7b3b79)
Replace Airoha AN7581 PWM patch with upstream version and add kernel
version tag.
(cherry picked from commit 2352de96c1)
[ fix conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport upstream minor fixed for NPU handling that might result in
kernel panic or handle leak.
(cherry picked from commit 83eacb6ab0)
[ fix conflict errors ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add missing leds and network board files for EN7581 SoC.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
[ drop reference to downstream 10g RFB board ]
Link: https://github.com/openwrt/openwrt/pull/20556
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 738eacb9a0)
Similar to e92b153e99 ("mediatek: introduce KERNEL_LOADADDR to Device/Default template"),
let's move the default loadaddr to Device/Default.
What's more, use 0x80200000 instead of the SDK default value 0x80088000
to avoid the following error which may overwrite TZ memory and cause crash:
[ 0.000000] [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader!
[ 0.000000] OF: reserved mem: Reserved memory: failed to reserve memory for node 'atf@80000000': base 0x0000000080000000, size 2 MiB
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
[ fix spelling mistake ]
Link: https://github.com/openwrt/openwrt/pull/20470
(cherry picked from commit fed2d31343)
[ fix conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Enable USB node on eMMC RFB board and disable USB2 3.0 port to make the
3rd PCIe line correctly work.
This is needed to prevent the xHCI driver to mess with PCIe by
configuring the USB2 3.0 port. Port will still be detected but won't be
configureed by the driver and won't have PHY to configure for.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 6d51c80424)
The 3rd PCIe line use the USB2 serdes for PCIe operation. Correctly set
it to the DT node so that the mode can be correctly set in the PHY
driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3ba92e0e32)
Add pending patch for USB support on AN7581 SoC. This is also required
to make operational the 3rd PCIe line that use the USB2 Serdes for PCIe
operations.
(cherry picked from commit 7afc2da3fc)
[ fix conflict errors, add missing Kconfig flag ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some SoC might use the Serdes for the second USB port as a 3rd PCIe
line (with the SSTR register correctly setup).
Add the node for the 3rd PCIe card and enable for the eMMC RFB board.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 2fae199953)
Backport a patch fixing a kernel panic on airoha_hw_init fail. This
should better handle scenario with NPU load Probe deferring.
(cherry picked from commit c3c75d0e68)
[ fix conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport cleanup patch for Airoha Ethernet patch to permit easier
backport in the future.
Automatically refresh all affected patch.
(cherry picked from commit 2f3ea18f91)
[ fix conflict errors, drop upstream patch ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Airoha AN7581 eMMC RFB board mount 2 Aeonsemi AS21xxx PHY. One is
usually connected to GDM4 and the other is optionally connected to GDM2.
Add the relevant nodes to support the one connected to GDM4.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 26da4bf552)
Pack the BL2 and BL31+U-Boot artifacts as Airoha AN7581 is currently
supported in upstream U-Boot and bootloader files can be used for
unfused boards.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 17cb69fe7f)
Backport additional patch required for NPU support of Airoha AN7583.
These are specific for the NPU module with some minor fixes and to adds
upport for loading the specific Airoha AN7583 NPU firmware.
(cherry picked from commit 8b4adfbb87)
[ fix conflict errors ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add relevant nodes for NPU support for Airoha AN7583 and enable the
kernel config to enable support in the Airoha Ethernet driver.
NPU firmware is scheduled to be upstreamed to linux-firmware and will be
added once present upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 8758b58f25)
Fix the current image Makefile for Airoha AN7583 by dropping the
artifacts entry for bootloader and add default PKG for the PHY mounted
on the RFB boards.
The artifacts for the bootloader will be readded later once ATF-A
support will be pushed mainline.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a7964f0893)
While adding support for Airoha AN7583, it was forget to push the EMMC
DTS while defining the variant in the image Makefile.
Add the missing DTS to fix image creation error.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 6fe65d404b)
On the Airoha AN7583 EVB there are 2 Aeonsemi AS21xxx PHY but only the
one connected to Serdes Ethernet is usable as the other connected to
Serdes PON is not actually HW connected (as the serdes is connected to
the BOSA port)
Add comments and disable the relevant PHY.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit ea850b5a18)
Backport upstream patch for AN7583 Ethernet support. While at it also
backport some additional fixes required to apply the AN7583 patches
cleanly.
Refresh all affected patch automatically (aside from the XSI patch that
changed the implementation)
Link: https://github.com/openwrt/openwrt/pull/20489
(cherry picked from commit 46a454fb9b)
[ fix conflict errors ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add missing syscon compatible for scuclk node.
Fix the unit-address of the scuclk node.
This fixes the pcs driver error:
airoha-pcs 1fa08000.pcs: probe with driver airoha-pcs failed with error -22
airoha-pcs 1fa09000.pcs: probe with driver airoha-pcs failed with error -22
Fixes: c3d70b1 ("airoha: en7581: Add support for external PHY")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20190
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a30daf8a0b)
All devices under airoha use dts directory under the target,
so update the default DEVICE_DTS_DIR. Also set the default
DEVICE_DTS based on the SoC name for non-dev boards.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20190
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 866c4e5cdf)
Introduce initial support for Airoha AN7583 SoC and add all the required
patch for basic functionality of the SoC.
Airoha AN7583 is based on Airoha EN7581 SoC with some major changes on
the PHY handling and Serdes. It can be see as a lower spec of EN7581
with modern and simplified implementations.
All the patch are sent upstream and are pending revision. Support for
PCIe and USB will come later as soon as DT structure is accepted
upstream.
(cherry picked from commit c5b12fc02a)
[ fix conflict errors, add MDIO_AIROHA config ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This add a pending version of the Airoha PCS driver to add support for
External PHY. The Airoha PCS driver will receive some minor modification
once we the PCS subsystem will be defined upstream.
Add all the required node for GDM2 and GDM4 and enable the PCS config.
(cherry picked from commit c3d70b1ae5)
[ fix conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
No functional changes intended.
Fixes warning:
/linux/arch/arm64/boot/dts/airoha/en7581-gemtek-w1700k.dtb: i2c1@1fbf8100 (mediatek,mt7621-i2c): status: 'oneOf' conditional failed, one must be fixed:
['disable'] is not of type 'object'
'disable' is not one of ['okay', 'disabled', 'reserved', 'fail', 'fail-needs-probe']
from schema $id: http://devicetree.org/schemas/dt-core.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20131
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3872e9d317)
The baud rate control on Airoha does not function properly. This
patch enables the inactive code responsible for this. The UART2
baud rate is correct. HSUART3 operates at twice the requested
baud rate. The same problem exists in the current code, so this
doesn't introduce any regression. Support for baud rates higher
than 460800 is still required. This will be added in the future.
Tested on Gemtek W1700k. UART2 and HSUART3 are working fine.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20049
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 440b85f5b1)
[ solve conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport fixes for Airoha pinctrl driver for PHY LED and MDIO bus. This
fix a copy-paste error for PHY LED and a misconfiguration for MT7530
embedded Switch MDIO bus GPIO pin to permit usage of external PHYs.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 35ff70e807)
Add the NPU and reserved memory node for AN7581 dtsi since it's not
supported.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3dca527e6d)
Major backport of upstream patch for support of multiple feature of the
Airoha Ethernet driver.
Feature backported are TSO, Jumbo packet, Offload and initial Wlan
Offload support.
Link: https://github.com/openwrt/openwrt/pull/19816
(cherry picked from commit 9d3009f426)
[ add missing kconfig flag ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport trivial fixes from upstream related to pinctrl and ethernet
driver.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 354d7472d5)
Backport patch adding support for AN7581 Ethernet PHY based on the same
Mediatek embedded Switch PHY.
Link: https://github.com/openwrt/openwrt/pull/19816
(cherry picked from commit 0adaeff5ee)
[ rework backported patch ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace thermal patch with upstream version. The thermal maintainer
reported that the sysfs entry are considered deprecated and that slope
and offset should be handled internally to the driver.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a713260966)
This board is also as known as E-Life ETR631-T/ETR635-U.
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Uncompress the configuration:
* Enter fakeroot if you are not login as root.
tar -zxf <filename>.tar.gz
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; telnetd; ) &
5. Repack the configuration:
tar -zcf backup.tar.gz etc/
6. Upload new configuration via web interface, now you can connect to
KOMI A31 via telnet.
Flash instructions:
1. Connect to KOMI A31, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-konka_komi-a31-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-konka_komi-a31-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20357
(cherry picked from commit 8a7de107d8)
[rebase uboot patches upon 24.10 branch]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20595
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
