Remove unused pinctrl groups defined in the device tree, probably as a
result of importing the vendor device tree which is based on the
reference board from MediaTek's SDK.
114b5c2063 ("mediatek: filogic: Add support ASUS RT-AX57M")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 96205c99d01cf7f5e69f03ccdea790d0eb9ddb36)
Signed-off-by: Garrett Mesmer <garrettmesm@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21237
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ASUS RT-AX57M, RT-AX54HP V2, RT-AX1800HP V2, RT-AX1800S V2, and RT-AX3000S all use the same firmware and have identical hardware
Hardware
--------
SOC: MediaTek MT7981b
RAM: 256MB DDR3L (Winbond W632GU6NB-09)
FLASH: 128MB SPI-NAND (Winbond W25N01KVZEIR)
WIFI: Mediatek MT7981b + Mediatek MT7976DAN 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531AE Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
MAC addresses
-------------
LAN Label MAC (stored in mtd ubi Factory partition at offset 0x4)
WAN LAN
2.4G LAN + 2 in first octet
5G LAN
Installation
-----------------------------------------------------------
Vendor-UI Method
-----------------------------------------------------------
1. Download the OpenWrt initramfs.trx image.
2. Connect the PC via LAN to one of the yellow router ports and wait
until your PC to get a DHCP lease.
3. Browse to http://192.168.1.1 (or whatever your router IP is configured as)
4. If your router is brand new, finish the setup process and log into
the Web-UI.
5. Navigate to Administration -> Firmware Upgrade and upload the
downloaded OpenWrt initramfs.trx image.
6. Wait for OpenWrt to boot. Open the default OpenWrt IP in a web browser and perform a system upgrade using the sysupgrade image as instructed in the top banner.
---------------------------------------------------------------------------
Revert to stock firmware:
1: Install package facinstall -> https://forum.openwrt.org/t/facinstall-package-for-easy-installation-factory-images/177587
2. Install Asus stock trx image via OpenWRT LuCI interface.
Signed-off-by: Garrett Mesmer <garrettmesm@gmail.com>
Co-Authored-By: Oleg S <remittor@gmail.com>
Signed-off-by: Oleg S <remittor@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20491
(cherry picked from commit d09e2b1926a6009299eb034928df2c6b6b04dfa8)
Link: https://github.com/openwrt/openwrt/pull/21237
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The SUPPORTED_DEVICES sets for both Maxlinear (v1) and Airoha (v2)
devices were identical, so sysupgrade was unable to detect when an
incorrect image was being installed. This caused "soft bricking" of
devices when a v1 image was installed on a v2 device, and vice versa.
Fix this by making the supported_devices distinct for each device
version, by renaming the devices with a version-specific name.
This is reflected in the file name and the image metadata.
Fixes: https://github.com/openwrt/openwrt/issues/20566
Fixes: https://github.com/openwrt/asu/issues/1525
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20632
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b71f4665cd)
Wifi on the 6GHz band does not support open networks, configure owe by
default. 6GHz wifi also needs a country code, configure a broken country
code '00' by default to hint the user to change it.
Link: https://github.com/openwrt/openwrt/pull/21313
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 01a87f4bd0)
Without this patch, the
if (!config.wpa)
config.wpa_pairwise = null;
is overwritten immediately.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Link: https://github.com/openwrt/openwrt/pull/21215
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit bc4e7fd38e)
Changes:
* use upstream patches for airoha-snfi driver
* update in kernel en7523 dts to add spinand support
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/21299
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit d9b1c74780)
The EW71v2 has the WAN port configured at eth1.
The printed label-mac is configured on this iface in openwrt.
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
(cherry picked from commit 7f3537ee2c)
When wdev interfaces and hostapd interfaces are mixed, race conditions
can occur. Sometimes all interfaces are started correctly, sometimes only
the wdev interface and some of the hostapd interfaces, and sometimes only
the wdev interface.
Fix this by creating the wdev interfaces first, before processing
wpa_supplicant or hostapd interfaces.
Link: https://github.com/openwrt/openwrt/pull/21303
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit 2015a40c38)
RTL930x devices have highmem starting address at 0x20000000.
The Linksys LGS328C highmem definition is wrongly shared with
the larger LGS352C RTL931x model and starts at 0x90000000.
Fix it by splitting the definition.
Fixes: 853d73f ("realtek: add support for Linksys LGS328C")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5d7470d4ca)
Include XHCI USB drivers on the Cudy WR3000P v1 router, the drivers are
required to be able to use the USB port for USD devices.
Closes: https://github.com/openwrt/openwrt/issues/21231
Fixes: 04e9d154f2 ("mediatek: filogic: add support for Cudy WR3000P v1")
Signed-off-by: Dmitry Mostovoy <dmitry.mostovoy@ceifx.com>
Link: https://github.com/openwrt/openwrt/pull/21281
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 9da57e2f82)
This typo makes the script fail with:
-ash: /etc/hotplug.d/ieee80211/10_fix_wifi_mac: line 66: syntax error: unexpected word (expecting ")")
which ultimately prevents the mac address for certain devices wireless cards being set correctly
Signed-off-by: Nick French <nickfrench@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21287
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit cb94962ac4)
Add EHT* check so that the hwmode will display 802.11be capability correctly.
Signed-off-by: Elwin Huang <s09289728096@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21267
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit 95112a4939)
ipq5018 do not support freq scaling and therefore stuck on 800Mhz
This patch allows CPU to run with 1.008 Ghz as designed
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
Link: https://github.com/openwrt/openwrt/pull/21185
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit c1290fa48c)
Mesh interfaces may not define an encryption setting. This results in
a ucode runtime error when parse_encryption() is called:
Reference error: left-hand side expression is null
In parse_encryption(), file /usr/share/ucode/wifi/iface.uc, line 20, byte 32:
called from function setup_sta (/usr/share/ucode/wifi/supplicant.uc:59:31)
called from function generate (/usr/share/ucode/wifi/supplicant.uc:243:41)
called from function setup (./mac80211.sh:254:61)
called from anonymous function (./mac80211.sh:342:14)
` config.auth_type = encryption[0] ?? 'none';`
Near here ------------------------^
Link: https://github.com/openwrt/openwrt/pull/21293
(cherry picked from commit 00e6c18a93)
Link: https://github.com/openwrt/openwrt/pull/21295
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add menuconfig option 'kmod-usb-gadget-fs' for the USB FunctionFS gadget
module
OpenWRT is perfect for USB gadgets that are network-enabled, since it
provides everything needed to easily manage the device. Having support
for the FunctionFS gadget enables the use of any custom USB devices
that does not have a specific module, like Media Transfer Protocol.
Signed-off-by: Dominic Germain <dominic@germain.cc>
Link: https://github.com/openwrt/openwrt/pull/21207
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 22a69dfa4a)
The ncm proto handler ignored ip4table, ip6table, and mtu settings.
The fix is based on the existing code in the mbim proto handler.
Fixes: #20216.
Signed-off-by: Alexander Patrakov <patrakov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20217
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b289edd84b)
libc depends on knowing libgcc's ABI, so it needs to be evaluated first.
Otherwise libc will depend on an ABI-less libgcc causing the rest of the
toolchain to fail.
Building package index...
ERROR: unable to select packages:
libgcc (virtual):
note: please select one of the 'provided by'
packages explicitly
provided by: libgcc1
required by: world[libgcc]
Before:
libc fused dependencies: libgcc
libgcc fused dependencies:
libatomic fused dependencies: libgcc1
After:
libgcc fused dependencies:
libc fused dependencies: libgcc1
libatomic fused dependencies: libgcc1
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/21265
(cherry picked from commit 5e32bfbf4b)
Link: https://github.com/openwrt/openwrt/pull/21253
Signed-off-by: Robert Marko <robimarko@gmail.com>
The updated logic for the APK dependencies and provides is as follows:
- If ABI version is defined:
- package is named `package_name-ABI_version`
- package implicitly provides
`package_name-ABI_version=package_version`
this implies that only one version of a package per ABI can be
installed at the same time
- additionally provide `package_name` so multiple packages can be
looked up by its base name
- for each `provides`, provide `provide-ABI_version=package_version`
this implies that only one version of a provide can be installed at
the same time
- else if ABI version is _not_ defined
- package is named `package_name`
- package implicitly provides `package_name=package_version`
this implies that only one version of a package can be installed at
the same time
- if `alternatives` is defined
- for each `provides`, provide `provide`
this implies that multiple versions of a provide can be installed
at the same time
- else if `alternatives` is _not_ defined
- for each `provides`, provide `provide=package_version`
this implies that only one version of a provide can be installed
at the same time
Both cases a package can be looked up by its base name.
ABI version `alternatives`, `conffiles`, `conffiles_static`, `list` and
`rusers` files so multiple versions of the same ABI package can be
installed side by side, and so they don't overwrite each other's
packaging files.
ABI version `EXTRA_DEPENDS` so dependencies can be correctly looked up
using the existing OpenWrt semantics without the ABI specified. This is
needed since ABI-versioned libraries no longer provide
`package_name=package_version`, so that they can be installed side by
side.
Remove duplicate dependencies when `EXTRA_DEPENDS` specifies a versioned
one that is already in `DEPENDS`.
ABI is defined
------------------------------------------------------------------------
`libsqlite3` has `PROVIDES` set to `libfake` and has two different ABI
versions installed. `libfake` is just an example to demonstrate the
mechanics, as the library can already be depended upon using e.g.
`libsqlite3-0=3.51.0-r1`. Note the ABI-versioned lists.
```
root@OpenWrt:/tmp# apk add --allow-untrusted ./libsqlite3-0-3.51.0-r1.apk
(1/1) Installing libsqlite3-0 (3.51.0-r1)
libsqlite3-0-3.51.0-r1.post-install: Executing script...
OK: 22 MiB in 157 packages
root@OpenWrt:/tmp# apk add --allow-untrusted ./libsqlite3-1-4.00.0-r1.apk
(1/1) Installing libsqlite3-1 (4.00.0-r1)
libsqlite3-1-4.00.0-r1.post-install: Executing script...
OK: 23 MiB in 158 packages
root@OpenWrt:/tmp# apk query --fields name,version,contents,provides libsqlite3-0 libsqlite3-1
Name: libsqlite3-0
Version: 3.51.0-r2
Provides: libfake-0=3.51.0-r2 libsqlite3
Contents:
lib/apk/packages/libsqlite3-0.list
usr/lib/libsqlite3.so.0
usr/lib/libsqlite3.so.3.51.0
Name: libsqlite3-1
Version: 4.00.0-r1
Provides: libfake-1=4.00.0-r1 libsqlite3
Contents:
lib/apk/packages/libsqlite3-1.list
usr/lib/libsqlite3.so.1
usr/lib/libsqlite3.so.4.00.0
root@OpenWrt:/tmp# ls -lh /usr/lib/libsqlite3.so.*
lrwxrwxrwx 1 root root 20 Nov 20 00:23 /usr/lib/libsqlite3.so.0 -> libsqlite3.so.3.51.0
lrwxrwxrwx 1 root root 20 Nov 20 00:27 /usr/lib/libsqlite3.so.1 -> libsqlite3.so.4.00.0
-rwxr-xr-x 1 root root 1.0M Nov 6 18:19 /usr/lib/libsqlite3.so.3.51.0
-rwxr-xr-x 1 root root 1.0M Nov 6 18:19 /usr/lib/libsqlite3.so.4.00.0
```
ABI is not defined
------------------------------------------------------------------------
Both `avahi-dbus-daemon` and `avahi-nodbus-daemon` provide `avahi-daemon`,
but have no ABI specified. This results in `avahi-daemon=0.8-r11` provides
for both packages and only one being able to be installed at the same time:
```
root@OpenWrt:/tmp# apk add --allow-untrusted ./avahi-nodbus-daemon-0.8-r11.apk
(1/4) Installing libavahi-nodbus-support (0.8-r10)
libavahi-nodbus-support-0.8-r10.post-install: Executing script...
(2/4) Installing libdaemon (0.14-r5)
libdaemon-0.14-r5.post-install: Executing script...
(3/4) Installing libexpat (2.7.3-r1)
libexpat-2.7.3-r1.post-install: Executing script...
(4/4) Installing avahi-nodbus-daemon (0.8-r11)
avahi-nodbus-daemon-0.8-r11.post-install: Executing script...
23 MiB in 160 packages
root@OpenWrt:/tmp# apk query --fields provides avahi-nodbus-daemon
Provides: avahi-daemon=0.8-r11
root@OpenWrt:/tmp# apk add --allow-untrusted ./avahi-dbus-daemon-0.8-r11.apk
ERROR: unable to select packages:
avahi-dbus-daemon-0.8-r11:
conflicts: avahi-nodbus-daemon-0.8-r11[avahi-daemon=0.8-r11]
satisfies: world[avahi-dbus-daemon><Q1R111s+ke9Vf+eCxDHX2BZVUK54Q=]
avahi-nodbus-daemon-0.8-r11:
conflicts: avahi-dbus-daemon-0.8-r11[avahi-daemon=0.8-r11]
satisfies: world[avahi-nodbus-daemon><Q1BAu7nLI2MgRabpveLTGO2ksQz7E=]
```
Provides and alternatives
------------------------------------------------------------------------
Both `uclient-fetch` and `wget-nossl` provide `wget` and specify
alternatives, so provides are not versioned and both packages can be
installed at the same time:
```
root@OpenWrt:/tmp# apk query --fields name,version,contents,provides uclient-fetch wget-nossl
Name: uclient-fetch
Version: 2025.10.03~dc909ca7-r1
Provides: wget
Contents:
bin/uclient-fetch
lib/apk/packages/uclient-fetch.alternatives
lib/apk/packages/uclient-fetch.list
Name: wget-nossl
Version: 1.25.0-r1
Provides: gnu-wget wget
Contents:
lib/apk/packages/wget-nossl.alternatives
lib/apk/packages/wget-nossl.list
usr/libexec/wget-nossl
```
Fixes: https://github.com/openwrt/openwrt/issues/20582
Fixes: https://github.com/openwrt/openwrt/issues/20802
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/20819
(cherry picked from commit 18029977f6)
Link: https://github.com/openwrt/openwrt/pull/21253
Signed-off-by: Robert Marko <robimarko@gmail.com>
Interrupt vector for reo2host-status is wrongly assigned.
Status interrupts weren't received and a workaround was applied to
mac80211 to periodically poll the reo status ring. Therefore, the
workaround can be removed with the proper hardware interrupt line
assigned.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21272
Signed-off-by: Robert Marko <robimarko@gmail.com>
Sync the DTS with the version sent upstream, clock bindings also.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit bce8432bbd)
After merge of https://github.com/openwrt/openwrt/pull/20709 I noticed,
that https://mirror-03.infra.openwrt.org/snapshots/targets/ath79/tiny/
still does not contain the build for RE450.
I analyzed the problem and noticed, that only builds which fits into
original size can be build and if the image is larger, it fails with
the following error: "WARNING: Image file .../openwrt/build_dir/
target-mips_24kc_musl/linux-ath79_tiny/tmp/
openwrt-ath79-tiny-tplink_re450-v1-squashfs-sysupgrade.bin is too big:
> 7864320".
This error is quite misleading as the image is smaller than 7864320. The
reason for this error is that default tplink-safeloader has hardcoded
factory partition structure and fails to generate any file.
Rather then fixing tplink-safeloader I followed approach from commit
ebd5e5fb53 ("ramips: switched TP-Link RE305 v1 to new partition layout")
and switched away from "tplink-safeloader sysupgrade".
I did not include "IMAGES := sysupgrade.bin", because with tiny target it
is still possible to locally build even factory image.
Fixes commit e768731dc8 ("ath79: switch TP-Link RE355 v1, RE450 v1 and
RE450 v2 to mtd-concat").
Signed-off-by: Radek Dostál <rd@radekdostal.com>
Link: https://github.com/openwrt/openwrt/pull/21158
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit bdbb4bdfa0)
Popular cheap PWM fans for this machine, like the ones coming in
heatsink+fan combos will not work properly at the currently defined
medium speed. Trying different pwm setting using a command
echo $value > /sys/devices/platform/pwm-fan/hwmon/hwmon1/pwm1
I found:
pwm1 value fan rotation speed cpu temperature notes
-----------------------------------------------------------------
0 maximal 31.5 Celsius too noisy
40 optimal 35.2 Celsius no noise hearable
95 minimal
above 95 does not rotate 55.5 Celsius
-----------------------------------------------------------------
Current cooling levels are:
cooling-levels = <255 96 0>;
Thus only cpu-active-high and cpu-active-low modes are usable.
This patch fixes cpu-active-medium settings for bpi-r3 board.
This patch may not be enough. Users may wants to tweak their thermal_zone0
trip points, thus tuning fan rotation speed depending on cpu temperature.
That can be done on the base of the following example:
=== example =========
# cpu temperature below 25 Celsius degrees, no rotation
echo 25000 > /sys/class/thermal/thermal_zone0/trip_point_4_temp
# cpu temperature in [25..32] Celsius degrees, normal rotation speed
echo 32000 > /sys/class/thermal/thermal_zone0/trip_point_3_temp
# cpu temperature above 50 Celsius degrees, max rotation speed
echo 50000 > /sys/class/thermal/thermal_zone0/trip_point_2_temp
=====================
Changes v2:
* put patch to a proper directory
* updated patch description
* tested with latest openwrt based on linux-6.6
Changes v3:
* use upstream linux patch
* update patch description
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17130
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 095151b235)
0779ee287db5 dhcpv6-ia: reconfigure message length bug fix
d69896b0ac7c all: remove dead code
3f6b3b4b9f8a odhcpd: remove fallback DNS search domain
ff3f72fdd01d router: remove some log spam in send_router_advert()
c1cc541e1065 router: improve send_router_advert()
901851b883da router: Modify relayed RA PIO P flag according to interface policy
179429ba477d router: Modify relayed RA PIO A flags according to interface policy
cb1b8770b7...0779ee287d
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
cb1b8770b782 config: add default value for dhcpv6_pd_min_len
20eb94d02dfe config: allow minimum PD len up to 64
7ebd96083971 Revert "router: optimize duplicated PIO comparison"
90ae6fc6e478 statefiles: don't consider no hostname as broken
1ff1328a4f...cb1b8770b7
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
- Security: Avoid privilege escalation via unix stream forwarding in Dropbear
server. Other programs on a system may authenticate unix sockets via
SO_PEERCRED, which would be root user for Dropbear forwarded connections,
allowing root privilege escalation.
Reported by Turistu, and thanks for advice on the fix.
This is tracked as CVE-2025-14282, and affects 2024.84 to 2025.88.
It is fixed by dropping privileges of the dropbear process after
authentication. Unix stream sockets are now disallowed when a
forced command is used, either with authorized_key restrictions or
"dropbear -c command".
In previous affected releases running with "dropbear -j" (will also disable
TCP fowarding) or building with localoptions.h/distrooptions.h
"#define DROPBEAR_SVR_LOCALSTREAMFWD 0" is a mitigation.
- Security: Include scp fix for CVE-2019-6111. This allowed
a malicious server to overwrite arbitrary local files.
The missing fix was reported by Ashish Kunwar.
- Server dropping privileges post-auth is enabled by default. This requires
setresgid() support, so some platforms such as netbsd or macos will have to
disable DROPBEAR_SVR_DROP_PRIVS in localoptions.h. Unix stream forwarding is
not available if DROPBEAR_SVR_DROP_PRIVS is disabled.
Remote server TCP socket forwarding will now use OS privileged port
restrictions rather than having a fixed "allow >=1024 for non-root" rule.
A future release may implement privilege dropping for netbsd/macos.
- Fix a regression in 2025.87 when RSA and DSS are not built. This would lead
to a crash at startup with bad_bufptr().
Reported by Dani Schmitt and Sebastian Priebe.
- Don't limit channel window to 500MB. That is could cause stuck connections
if peers advise a large window and don't send an increment within 500MB.
Affects SSH.NET https://github.com/sshnet/SSH.NET/issues/1671
Reported by Rob Hague.
- Ignore -g -s when passwords arent enabled. Patch from Norbert Lange.
Ignore -m (disable MOTD), -j/-k (tcp forwarding) when not enabled.
- Report SIGBUS and SIGTRAP signals. Patch from Loïc Mangeonjean.
- Fix incorrect server auth delay. Was meant to be 250-350ms, it was actually
150-350ms or possibly negative (zero). Reported by pickaxprograms.
- Fix building without public key options. Thanks to Konstantin Demin
- Fix building with proxycmd but without netcat. Thanks to Konstantin Demin
- Fix incorrect path documentation for distrooptions, thanks to Todd Zullinger
- Fix SO_REUSEADDR for TCP tests, reported by vt-alt.
Dropped:
* 050-dropbear-multihop-fix.patch as its included in the release 5cc0127000db5f
* 051-fix-pubkey-options.patch as its included in the release 1d4c4a542cd5df
* 052-fix-missing-depends-for-sntrup761x25519-sha512.patch as its included
in the release 1a2c1e649a1824
* 053-Don-t-limit-channel-window-to-500MB.patch as its included in the release a8610f7b98ad
Manually rebased:
* 110-change_user.patch
Fixes: CVE-2025-14282, CVE-2019-6111
Reviewed-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Konstantin Demin <rockdrilla@gmail.com>
Tested-by: Konstantin Demin <rockdrilla@gmail.com> [mediatek/filogic (GL.iNet GL-MT6000)]
Link: https://github.com/openwrt/openwrt/pull/21186
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 70a4da1ceb)
The u-boot target name has to match the u-boot configuration. Switch
this back to the old names.
Fixes: d871e95e7f ("sunxi: image: sync target profiles names with DT compatible")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 86996634f0)
This fixes a failed bring up of the radio on bootup
if the model defines a rename of phy in its /etc/board.json.
This specifically impacts Redmi AX6S and any router that does so
in its /etc/board.json. The fix fortunately is simple, just update
phy name in phys after rename.
The entry that specifically causes this issue is the following:
{
<omitted>
"wlan": {
"wl0": {
"path": "platform/18000000.wmac",
"info": {
"antenna_rx": 15,
"antenna_tx": 15,
"bands": {
"2G": {
"ht": true,
"max_width": 40,
"modes": [
"NOHT",
"HT20",
"HT40"
],
"default_channel": 1
}
},
"radios": [
]
}
},
...
}
The issue is that after rename, referenced phy in config is going to be
wl0 but in phys array it is still phy0; and so it fails to find phy
and does not bring up radio.
Fixes: https://github.com/openwrt/openwrt/issues/20250
Fixes: https://github.com/openwrt/openwrt/issues/20339
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/21175
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit e4d5e76af0)
Use the correct identifier 'rtsds_of_match' instead of
'rtsds_mdio_of_match' because the latter doesn't exist.
This doesn't cause an error for 6.12. However, with 6.18 the
implementation of MODULE_DEVICE_TABLE has changed to use 'static' and
'used' [1] instead of 'extern' and 'unused' [2].
[1] 7d0a66e4bb/include/linux/module.h (L260)
[2] adc218676e/include/linux/module.h (L249)
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21182
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit d519a3ee86)
As a first real usage of the new SerDes struct, move the polarity
configuration there. It was previously located in the global rtpcs_ctrl
struct as an array, indexed by SerDes id. Because this is per-SerDes
information, the new SerDes struct is the correct place to live in.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21146
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 56a71f3c82)
By using references to pre-initiated SerDes instances instead of plain
SerDes number, there is no need to check for the range anymore in
various places. During driver/pcs init it is ensured that only valid
SerDes will reach the configuration functions.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21146
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 18eea05483)
