These devices share the same "compatible" in device tree causing some
incompatibilities (sysupgrades, ASU profile identification), assign a
unique "compatible" and "model" to each variant.
Context:
Commit [1] added each variant's dts compatible to the SUPPORTED_DEVICES
field of the other variant to make easy sysupgrades between these
physically indistinguishable devices variants possible.
But there were found three issues which does not allow this:
- the sysupgrade's stricter check still used in some sysupgrade
paths(this check is being replaced(and redundant) with the newer fwtool's
SUPPORTED_DEVICES check using the info in images METADATA), this check
will fail when sysupgrading from a different board_name(compatible dts)
that the image was created for (image profile name).[2]
- ASU needs unique "dts compatible" to identify the devices profile.
- and an ASU's profile identification limitation when several devices from
a common target share SUPPORTED_DEVICES entries.[3]
There is a proposal for these issues but not yet implemented [4][3].
Until these issues are fixed we won't allow "easy" sysupgrades between
these two device variants.
Commit [5] avoided the ASU profile identification limitation but
missed the required two unique dts compatibles in order to make the two
variants fully work, although not allowing easy sysupgrade between them.
[1]: 8d30e07180
[2]: sysupgrade stricter check https://github.com/openwrt/openwrt/issues/20566#issuecomment-3583555482
[3]: ASU proposal https://github.com/openwrt/asu/pull/1533
[4]: allow easy sysupgrade proposal https://github.com/openwrt/openwrt/pull/20947
[5]: b71f4665cd
Fixes: b71f466 ("mediatek: filogic: fix supported_devices list for gl-mt2500")
Fixes: 8d30e07 ("mediatek: filogic: fix for new GL.iNet GL-MT2500/GL-MT2500A hardware revision")
Fixes: https://github.com/openwrt/openwrt/issues/20566
Fixes: https://github.com/openwrt/asu/issues/1525
Signed-off-by: Mario Andrés Pérez <mapb_@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21842
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7aa1f7e814)
The xrx200 ethernet driver falls back to a random MAC address on any
error from of_get_ethdev_address(), including -EPROBE_DEFER. When the
MAC address comes from an nvmem layout driver (such as u-boot-env on
NAND), the nvmem cell may not be available yet at first probe attempt.
Fix this by propagating EPROBE_DEFER so the driver probe is deferred
until the nvmem cell becomes available.
Tested on Zyxel P-2812HNU-F1 (NAND, u-boot-env nvmem layout).
Signed-off-by: Burak Aydos <byhexadecimal@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 50e7e5c80d)
Port 21 definition was missed during addition of LGS328C.
Add it to the dts.
Fixes: 853d73f ("realtek: add support for Linksys LGS328C")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21793
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 75fd2497ac)
Link: https://github.com/openwrt/openwrt/pull/21900
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Commit 78bf3a5f44 ("realtek: dsa: Fix rate control initialization") enabled
code setting up the "storm control" feature. This casued a speed regression
on rtl838x, reducing the effective max speed per port from line rate to around
500 Mbits/s.
Storm control is a policy feature with a number of input parameters depending
on use case and environment. It is not possible to define a meaningful static
policy in the driver. The problem isn't just the arbitrary limits in the
current code. Such features require userspace interfaces.
Drop this code for now. It wasn't missed while it was disabled.
Fixes: 78bf3a5f44 ("realtek: dsa: Fix rate control initialization")
Link: https://github.com/openwrt/openwrt/issues/21692
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://github.com/openwrt/openwrt/pull/21877
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3972aeaf7c)
Link: https://github.com/openwrt/openwrt/pull/21900
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Setup for DSA QOS on RTL839x accesses unitialized memory. For some
reason the handover of the priv structure was realized via global
intermediate variable switch_priv. During refactoring for adbb9a6
("realtek: dsa: rtl83xx: fix init section mismatch") this was not
noticed. Since then RTL839x devices crash during startup.
Fix this by using standard handover via function parameters.
Fixes: e81affb9 ("realtek: dsa: rtl83xx: fix init section mismatch")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21703
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit ac96463944)
Link: https://github.com/openwrt/openwrt/pull/21900
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Compilation currently spits this message:
WARNING: modpost: vmlinux: section mismatch in reference:
rtl83xx_sw_probe+0x6a4 (section: .text.rtl83xx_sw_probe)
-> rtl83xx_setup_qos (section: .init.text)
That means that we have a "normal" function caller (can be
called during the whole uptime) and a "initialization" function
callee (only available during init.
Fix this and directly fix the unwanted family checks.
Fixes: 012e0091 ("realtek: dsa: avoid use-after-free")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21690
(cherry picked from commit adbb9a6423)
Link: https://github.com/openwrt/openwrt/pull/21900
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The realtek target uses some functions marked __init for initialization.
However, that means they can only be called once when compiled in and
afterwards the memory occupied by them is freed and potentially reused.
Some "impossible" (code at a given location can't crash in the way it
does) crashes can be caused by this because upon re-execution of those
functions, garbage gets executed. Such re-execution can happen for
deferred probes or repeated probes.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Link: https://github.com/openwrt/openwrt/pull/21504
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit a91c3abe83)
Link: https://github.com/openwrt/openwrt/pull/21900
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit fixes non-working USB port:
---
[ 5.294036] xhci-mtk 11200000.usb: error -EPERM: Failed to get supply 'vbus'
[ 5.301163] xhci-mtk 11200000.usb: error -EPERM: Failed to get regulators
[ 5.307938] xhci-mtk 11200000.usb: probe with driver xhci-mtk failed with error -1
---
While testing the USB power on/off functionality during the previous
commit, I didn't sufficiently test the actual operation of the USB
devices.
Fixes: ff5e66a920 ("mediatek: add support for Routerich BE7200")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21795
(cherry picked from commit 2651a6ced9)
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21882
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for the Cudy AP3000 Wall v1.
SoC: MediaTek MT7981b
RAM: 256MiB
Flash: spi-nand spi0.0: 128 MiB
Wifi: MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
LEDs: 1 LED in two colors (red & white)
Buttons: 1 reset, 1 led on/off
Ethernet: 5x 1GbE
Power: PoE powered (standalone)
The stock firmware is a customized variant of OpenWrt, which implements
a signature check that only allows flashing official firmware. Cudy offers
intermediate OpenWrt firmware images on their website [1][2] which do not
implement the signature check. After flashing the intermediate image the
upstream official OpenWrt image can be installed.
The stock firmware can be recovered via TFTP using the U-Boot based boot
loader[3]. Set up a TFTP server on your computer with IP 192.168.1.88/24
serving the stock firmware from Cudy's website renamed to "recovery.bin".
Press and hold the reset button while powering on the device, wait for the
TFTP server to send the recovery.bin file, then release the reset button.
The router will take a couple of minutes to reboot and set up the stock
firmware.
[1] https://www.cudy.com/blogs/faq/openwrt-software-download
[2] https://drive.google.com/drive/folders/1BKVarlwlNxf7uJUtRhuMGUqeCa5KpMnj
[3] https://www.cudy.com/en-us/blogs/faq/how-to-recovery-the-cudy-router-from-openwrt-firmware-to-cudy-official-firmware
Signed-off-by: Derek Denk <derek.denk@live.com>
Link: https://github.com/openwrt/openwrt/pull/21266
(cherry picked from commit afad4c71f8)
Link: https://github.com/openwrt/openwrt/pull/21890
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The MT7531 has an incorrect interrupt number described in the DTS.
This commit also adds PHY interrupts. They work the same as on
the MT7988.
Tested on Gemtek W1700k.
Suggested-by: Benjamin Larsson <benjamin.larsson@genexis.eu>
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/21016
(cherry picked from commit 788958880b)
Link: https://github.com/openwrt/openwrt/pull/21838
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Bc-bocun Chen of MediaTek has discovered a memory leak in the error path
in our downstream patch for mtk_eth_soc which adds support for the 10G
PCS and PHY paths of the MT7988 SoC.
Fix this by freeing the at this point already allocated netdev resources
before returning the error.
Fixes: 4cb6bd9a6d ("mediatek: switch to pending XFI 10G Ethernet drivers")
Reported-by: Bc-bocun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 4d71c767c4)
The D-Link DIR-1360 A1 is an AC1300 router based on the MT7621AT SoC.
Specifications :-
* SoC: MediaTek MT7621AT
* RAM: 256 MB DDR3
* Flash: 128 MB SPI NAND (Winbond W29N01HV)
* WiFi: MT7615D (2.4 GHz + 5 GHz DBDC)
* Ethernet: 5x 10/100/1000 Mbps (1x WAN, 4x LAN)
* USB: 1x USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (White/Orange), Internet (White/Orange), USB, 2.4G/5G WLAN
MAC addresses are retrieved from the 'factory' partition via NVMEM.
LAN: 0xe000 (gmac0)
WAN: 0xe006 (gmac1)
WLAN: 0xe00c (pcie0)
Flash Instruction :-
1-Set a static IP on your PC (e.g., 192.168.0.10, Gateway 192.168.0.1).
2- Power off the router and connect your PC to a LAN port.
3- Hold the Reset button and power on the router; continue holding for 5 seconds.
4- Access the Recovery UI at http://192.168.0.1 in your browser.
5- Upload the OpenWrt factory.bin image and wait for the reboot.
With these definitions in place, the DIR-1360 A1 boots reliably, exposes all hardware features correctly, and can be flashed via both the OEM recovery interface and standard OpenWrt upgrade paths.
Signed-off-by: Aryaman Srivastava <aryamansrivastava895@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21616
(cherry picked from commit 7a8e2efed5)
Link: https://github.com/openwrt/openwrt/pull/21826
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Part of the phy patch process breaks functionality on non-Realtek
platforms. Only apply this on Realtek SoCs to fix functionality
everywhere else.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21777
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 268a0cb363)
Link: https://github.com/openwrt/openwrt/pull/21799
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The u-boot-env partition on the Zyxel P-2812HNU-F1 is 128 KiB but
the actual environment data is only 8 KiB (0x2000 bytes). Without
the env-size property, the u-boot,env nvmem layout driver assumes
env-size equals the full partition size and computes an incorrect
CRC32 over the entire 128 KiB, causing all nvmem cell reads to fail
silently.
Add env-size = <0x2000> so the CRC32 is computed over the correct
8 KiB region, allowing nvmem-cells (such as ethaddr) to be read
properly by the kernel.
Signed-off-by: Burak Aydos <byhexadecimal@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21780
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 6952844436)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit 53a525f346.
Linux 6.12.67 broke ipip6 tunnel (DS-Lite) and MAP-E.
Revert this Linux kernel bump till the problem is fixed.
Fixes: https://github.com/openwrt/openwrt/issues/21737
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Migration of the eDPU DTS to upstream one broke the eDPU plus model
since the required ethernet aliases are missing and U-Boot then cannot
find the required ethernet nodes.
So, after sending the required fix upstream, lets apply it in OpenWrt
as well.
Fixes: 9852dda410 ("mvebu: move DTS diff into a patch for Methode uDPU")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 3353827fb5)
Add the loop module and mkfs tool to use f2fs/ext4
based overlays. This fixes the following bug:
mount_root: unable to create loop device
mount_root: no usable overlay filesystem found, using tmpfs overlay
Fixes: 99545b4bb1 ("d1: add new target")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 1e7950a45d)
The USB of most d1 devices works in otg or peripheral mode.
Enable this feature to use usbgadget and fix musb errors:
musb-sunxi 4100000.usb: Invalid or missing 'dr_mode' property
musb-sunxi 4100000.usb: probe with driver musb-sunxi failed with error -22
Fixes: 99545b4bb1 ("d1: add new target")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 81580cc92c)
The CONFIG_SOFTLOCKUP_DETECTOR_INTR_STORM option shows up when the
OpenWrt option CONFIG_KERNEL_SOFTLOCKUP_DETECTOR is activated.
Link: https://github.com/openwrt/openwrt/pull/21710
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit bf9e90c94e)
The indicator is unused by default and not associated
with the wan port. So let’s fix this.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21635
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 46ff60ce02)
This is a cosmetic change. There is no need to use mac
address increment/decrement in the dts on these devices,
so this can be simplified.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21635
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 9bcfe7b76f)
In the original DTS from the device firmware, there are
no entries that enable SPI calibration. Therefore, it
should be disabled.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21635
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 299105441a)
Keenetic devices always use the WAN port MAC address as
the MAC address printed on the label.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21635
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5c195add76)
Add two missing $$ in the factory image build pipeline for MR6350
Signed-off-by: Zeyu Dong <dzy201415@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21682
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 979f70cc7e)
Now that DCB is enabled by default, it makes sense to include it on
lan969x.
While we are here, lets include ip-bridge as these devices are switches
and the Busybox applet does not expose enough functionality.
These devices have no space constraints.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 51710e9dd4)
Update the DTS to the latest pending upstream version, it looks like this
should get merged soon upstream.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 19e097e18a)
Interrupts for DWC3 node were completely mixed up - SPI interrupt 62 is
not listed in reference manual at all. It was also causing dtbs_check
warnings:
ipq5018-rdp432-c2.dtb: usb@8af8800 (qcom,ipq5018-dwc3): interrupt-names:0: 'pwr_event' was expected
ipq5018-rdp432-c2.dtb: usb@8af8800 (qcom,ipq5018-dwc3): interrupt-names: ['hs_phy_irq'] is too short
Warning itself was introduced by commit 53c6d854be4e ("dt-bindings: usb:
dwc3: Clean up hs_phy_irq in binding"), but this was trying to bring
sanity to the interrupts overall, although did a mistake for IPQ5018.
IPQ5018 does not have QUSB2 PHY and its interrupts should rather match
ones used in IPQ5332.
Correct it by using interrupts matching the bindings and reference
manual.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21454
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit e1a9636959)
In IPQ5018, the reference clock to the CMN PLL block from the on-board
Wi-Fi has its divider set to 2. This divider wasn't taken into
consideration when calculating the CMN PLL clock rate which meant the
resulting clock rate was doubled.
With the reference clock divider being accounted for in the driver,
correct the assigned clock rate to 4.8GHz.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21453
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit d6ab889e45)
Add missing dt-bindings/include files needed for compilation of driver.
Enable compilation of the CMN PLL driver by adding the symbols to
Kconfig and Makefile.
Fixes: 468975a985 ("qualcommax: ipq50xx: backport upstreamed patches for adding ipq5018 CMN PLL support")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21453
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit fdce6f99be)
This is tri-band WiFi6E capable router. Also Zyxel Nebula managed so no real local GUI. To open device 4 screws must be located uder the label.
Four latches are on front and two on each side. Better start from ethernet port side where 3 small latches are easy to handle.
FCC shows It's identical to WSQ65 sold as Zyxel Multy M6E but that's nowhare to be found yet. WSQ65 is not covered by this PR
Speficiations:
* SoC: Qualcomm IPQ5018
* RAM: 1GB DDR3
* Flash: Winbond W25N02KWZEIR 256MB
* UART: PCB "J3" is located left from front LED strip
(VCC/TX/RX/ /GND) 3.3V 115200n8
* Wi-Fi1: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
* Wi-Fi2: QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
* Wi-Fi3: QCN6122 (2x2:2 6 Ghz 802.11an/ac/ax)
* Ethernet: QCA8337 4xLAN 1Gbit / 1xWAN 1Gbit
* Buttons: WPS , Reset
* LEDs: 13 in total
RGB power, RGB wan, RGB status (cloud), RGB wifi, Green wps
* FCCID: I8803891
*Flash Instructions starts with getting root:
connect uart to J3 connector next to the front LEDs
go to failsafe when this shows up in log:
"Press the [f] key and hit [enter] to enter failsafe mode"
execute:
mount_root
passwd -d root
reboot
logon as root:
look for 'Please press Enter to activate this console.'
login is root password is empty
execute:
fw_setenv DebugFlag=0x1
fw_setenv bootdelay=0x2
passwd -d root
backup ubi partition "rootfs" into safe space
reboot
*OpenWrt installation
stop uboot and execute:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.10
tftpboot *-factory.ubi
flash rootfs
reset
or:
tftpboot *-initramfs-uImage.itb
bootm
use sysupgrade as usual
*restore OEM from backup
stop uboot and execute:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.10
tftpboot *-initramfs-uImage.itb
bootm
transfer rootfs.bin backup and execute:
ubiformat /dev/mtd16 -y -f /tmp/rootfs.bin
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
Link: https://github.com/openwrt/openwrt/pull/21042
(cherry picked from commit f948f71300)
Link: https://github.com/openwrt/openwrt/pull/21440
Signed-off-by: Robert Marko <robimarko@gmail.com>
The vr9.dtsi configures the GPIO 38 as reset GPIO. Also the fon LED is
configured on GPIO 38. This conflicts and makes the probing of the PCIe
controller fail in OpenWrt 25.12.
The AVM GPL source code configured GPIO 21 as PCIe reset.
Fixes: https://github.com/openwrt/openwrt/issues/21562
Link: https://github.com/openwrt/openwrt/pull/21641
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit a4285d7cc0)
On some SoCs like RK3399, U-Boot no longer export the serial
address in $stdout variable, it has been changed to something like
`stdout=serial,vidconsole` since video supported was added. So
detect $soc variable instead, this also makes the script more clear.
Addtional note: rk3566 is reported as rk3568, rk3582 is reported as
rk3588 in $soc.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/21610
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 609deedd87)
