They have the same 0x200 calibration size.
Added various compatible lines in various places to make it clear what
device we're talking about.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19863
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These devices use AR9285, which uses 1f8 as the calibration size, not
440 like newer chips do. Actually the driver mandates a minimum of 200.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19863
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The TP-Link Archer VR1200v (v2) is a low end DSL modem based on the
EcoNet EN751221 processor platform.
While it does have an unlocked bootloader, the factory upgrade feature
requires a cryptographic signature so flashing from the web UI is not
feasible.
The Archer VR1200v (v2) uses a dual-image layout. I have chosen to reuse
this to support dual-boot between OpenWRT and the factory firmware.
Flashing instructions (from bootloader):
Build and then locate the squashfs-sysupgrade.bin image file
Get the length of that file in hex: printf '%X\n' "$(stat -c%s the-file-squashfs-sysupgrade.bin)"
Connect to device with xmodem capability, e.g. picocom --send-cmd lsx -vv -b 115200 /dev/ttyUSB0
Switch device on and press a key within 3 seconds, you should get to a `bldr>` prompt
Type: xmdm 80020000 <file length hex>
Quickly start xmodem and send the file, in picocom that is ctrl+a ctrl+s <paste-the-file-name> enter If the transfer fails to start, wait 30 seconds to a minute for the bootloader prompt to return and then try the command again.
Once the transfer has completed successfully, type the following flash 80000 80020000 <file length hex>
Type `re` or simply restart the device to boot into OpenWRT
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://github.com/openwrt/openwrt/pull/19021
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The SmartFiber XP8421-B is a fiber modem which is available for $20 online
and has 512MB of memory, 256MB of SPI NAND flash and 2 USB 2.0 ports in
addition to ethernet, wifi and XPON.
Because EcoNet is not currently producing evaluation boards, the XP8421-B
stands in as a convenient, low cost, off-the-shelf, representitive example
of the capabilities of the EN751221 econet processor. This is also the
example board that is included in the upstream Linux patchset.
The XP8421-B, and apparently many other devices of this platform, use a
dual-image layout. I have chosen to reuse this to support dual-boot between
OpenWRT and the factory firmware. Certain design decisions were made with
the goal of not overwriting data that is used by the factory OS.
This commit also introduces a utility for switching between OS_A and OS_B
which are used for OpenWRT and Factory OS respectively.
Flashing instructions (from bootloader):
Build and then locate the squashfs-tclinux.trx image file
Get the length of that file in hex: printf '%X\n' "$(stat -c%s the-file-squashfs-tclinux.trx)"
Connect to device with xmodem capability, e.g. picocom --send-cmd lsx -vv -b 115200 /dev/ttyUSB0
Switch device on and press a key within 3 seconds
Enter bootloader username and password: telecomadmin nE7jA%5m
Type: xmdm 80020000 <file length hex>
Quickly start xmodem and send the file, in picocom that is ctrl+a ctrl+s <paste-the-file-name> enter If the transfer fails to start, wait 30 seconds to a
minute for the bootloader prompt to return and then try the command again.
Once the transfer has completed successfully, type the following flash 80000 80020000 <file length hex>
Type go or simply restart the device to boot into OpenWRT
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://github.com/openwrt/openwrt/pull/19021
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
EcoNet EN75xx is a big endian MIPS platform used in XPON (fiber),
DSL, and SIM (3g/4g) applications. Complete GPL vender SDKs exist
for this platform, but are based on Linux 2.6.
The bulk of this submission has already been accepted upstream:
https://patchwork.kernel.org/project/linux-mips/list/?series=960479&state=*
This platform uses a bootloader that is derived from old TrendChip
code. This bootloader implements a frustratingly complex Bad Block
Table which is implemented here in en75_bmt.c
This BMT is not upstreamed because it depends on mtk_bmt framework
which likewise is not upstreamed.
This BMT system rewrites block indexes in flash and if the bootloader
considers it to be corrupted, it will attempt to automatically rebuild
on boot. So without implementing the algorithm, you can't safely use
the disk at all.
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://github.com/openwrt/openwrt/pull/19021
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
RockChip RK3568 ARM64 (4 cores)
1/2GB LPDDR4 RAM
2x 2500 Base-T (PCIe, r8125b)
1 LED (Power)
1 Button (Reset)
Micro-SD Slot
2x USB 3.0 Port
12V DC Jack
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card using
dd.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19990
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for the Lunzn FastRhino R66S board.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19990
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add labels wan and cpu for ethernet ports.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19968
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently 5G wireless interface MAC address is incorrect.
Fix by setting MAC address using Factory data.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19968
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Convert NWA50AX Pro to use NVMEM framework for wifi macaddr.
Also remove the unused macaddr@a.
Signed-off-by: Zhi-Jun You <hujy652@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/19982
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Convert NWA50AX Pro to use NVMEM framework for EEPROM/precal.
Signed-off-by: Zhi-Jun You <hujy652@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/19982
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These are already specified in DTS. Only thing missing is
label-mac-device.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19806
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Support in mt76 has existed for quite a while. Use it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19806
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
After trying to implement the gluon support for this device I ended up in a boot loop due to the usable amount of flash left. With this patch layout it uses the unused and empty flash space in the original partiton layout.
The version 3 of this device the RE365 share the same approach to have more usable space.
Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
Link: https://github.com/openwrt/openwrt/pull/18639
Signed-off-by: Sander Vanheule <sander@svanheule.net>
PKG_MAKE_FLAGS is required when compiling r8168-rss
Signed-off-by: Andy Chiang <AndyChiang_git@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20001
Signed-off-by: Robert Marko <robimarko@gmail.com>
A lot of definitions in the global mach include have been taken over
to the individual drivers. Only a few of the definitions are really
used nowadays. Remove all the unneeded lines.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19995
Signed-off-by: Robert Marko <robimarko@gmail.com>
- shrink data structures
- avoid unnecessary divisions
- support GSO fraglist on tx
Reapply with fixed patch
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use Linux kernel version 6.12 by default for loongarch64 target.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19980
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Boards such as [1] and [2] add an extra Ethernet port to Raspberry Pi (CM)5.
These typically use Realtek PCIe or USB Ethernet NICs. Include kmod-r8169 and
kmod-usb-net-rtl8152 by default to make it easy to configure LAN/WAN ports
with these parts on Raspberry Pi 5.
Because CM5 can fit in the same carrier boards as CM4, also ensure that both
devices have the same Ethernet NIC kmods.
[1]: https://www.waveshare.com/wiki/CM5-DUAL-ETH-MINI
[2]: https://www.waveshare.com/wiki/PCIe_TO_Gigabit_ETH_Board_(C)
Signed-off-by: Elbert Mai <code@elbertmai.com>
Link: https://github.com/openwrt/openwrt/pull/19384
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Certain boards have an at24(-compatible) EEPROM for storing various
parameters like MAC addresses. Enable support for this hardware across
the whole target.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
While these boards have an at24 EEPROM for storing the MAC address,
early revisions (up until about 2017) did not contain actual addresses.
Create a random address to have ethernet function properly in u-boot.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Backport fixes for Airoha pinctrl driver for PHY LED and MDIO bus. This
fix a copy-paste error for PHY LED and a misconfiguration for MT7530
embedded Switch MDIO bus GPIO pin to permit usage of external PHYs.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The RK356x/RK3588 SoCs support up to 10 serial ports.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19917
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The version of libxml2 was bumped from 2.13.6 to 2.14.5. Since version
2.14, libxml2 is not binary compatible with older versions. Therefore
add an abi version.
From the NEWS file:
Binary compatibility is restricted to versions 2.14 or newer. On ELF
systems, the soname was bumped from libxml2.so.2 to libxml2.so.16.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Link: https://github.com/openwrt/openwrt/pull/19983
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
gettext-full only provides libintl which is not licensed under
GPL-3.0.-or-later but under LGPL-2.1-or-later as stated in
gettext-runtime/intl/COPYING.LIB
Fixes: c10d97484a (Add more license tags with SPDX identifiers)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19943
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
elfutils libraries are not licensed under GPL-3.0-or-later, they are dual
licensed: GPL-2.0-or-later OR LGPL-3.0-or-later as clearly stated in
source files as well as on https://sourceware.org/elfutils:
The libraries and backends are dual GPLv2+/LGPLv3+. The utilities are GPLv3+.
Fixes: b98fb76646 (elfutils: import package from packages.git)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19941
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support so openwrt can be compiled using
coreutils from GNU or uutils.
Signed-off-by: Marcos Alano <marcoshalano@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19883
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Apart from improved power consumption, this fixes the runtime errors
from the pmdomain driver (failed to set idle on domain '%s')
Backport four clk fixes while at it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19925
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All devices supported by the Zynq target have either a Realtek or Marvell
PHY. The Vitesse PHY was enabled when the target was created (2d45ad07fc).
It's not used here, so it's safe to disable it.
Ethernet PHYs used by individual devices are listed below.
Device PHY
AVNET ZedBoard Marvell 88E1518
Digilent Zybo Realtek RTL8211E
Digilent Zybo Z7 Realtek RTL8211E or RTL8211F
Xilinx ZC702 Marvell 88E1116R
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19969
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This was done by executing these command:
$ make kernel_oldconfig CONFIG_TARGET=platform
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19969
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The devices are basically identical. The RAX3000Me can be with
ddr3 RAM.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19760
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds ddr3 build for the ddr3 variant of the CMCC RAX3000Me
router.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19760
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Airoha AN8855 switch. Some CMCC RAX3000Me hw
revisions are shipped with Airoha switch.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19760
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
MediaTek MT7981 WiSoC
512MB DDR4 RAM
128MB SPI-NAND
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
4 LAN MediaTek MT7531 PHY
1 WAN RTL8221B-VB-CG 2.5Gbps PHY
UART: 115200 8N1 3.3V
USB2 Port
PoE on WAN Port
MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set
Gotchas:
WAN LED does not light up (might require further DTS tweaks)
PoE on WAN port was not tested
This commit is heavily based on WR3000H one, I've just ported DTS differences
from the official image to get USB support and proper LED mapping.
Installation
------------
[Untested as I've received and used a transitional image from Cudy]
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device + press reset pin. Keep pressing reset pin to enter the U-Boot shell.
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.88. Rename the image to "cudy3000p.bin"
4. Download and boot the OpenWrt initramfs image.
$ tftpboot 0x46000000 cudy3000s.bin; bootm 0x46000000
5. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Signed-off-by: Michal Halva <hedik01@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19636
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
