Make clearer which field belongs to which register. For this
sort the fields below the registers and use indentation.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22075
Signed-off-by: Robert Marko <robimarko@gmail.com>
PHY polling setup has found a home in the mdio driver. For RTL931x
there still exists a setup sequence for polling type (serdes/mdio)
in the DSA driver. Put it where it belongs.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22075
Signed-off-by: Robert Marko <robimarko@gmail.com>
Allow building imagebuilder and/or sdk with dependency on the same
external toolchain as used to build the imagebuilder or sdk (so that ib
and sdk may be built using an external toolchain).
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
Original patch:
https://lists.openwrt.org/pipermail/openwrt-devel/2016-January/012552.html
[rebased to current main, impvove commit title]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22089
Signed-off-by: Robert Marko <robimarko@gmail.com>
It looks like commit 6d2f3b1b19 ("package: kernel: dtc: Add DTO support")
added this patch file 9 years ago without it ever being applied anywhere.
Back then there wasn't even a 'dtc' package, but we just used 'dtc' from
the Linux kernel sources.
Nowadays there is package/utils/dtc which is used to build dtc to be used
on the target (*not* a host-build!), and it of course already contains
support for device tree overlays since v1.4.3 from 2017...
This reverts commit 6d2f3b1b19.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/22118
Signed-off-by: Robert Marko <robimarko@gmail.com>
Get rid of defines that are not used in the driver.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22100
Signed-off-by: Robert Marko <robimarko@gmail.com>
This define is used nowhere. Remove it.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22100
Signed-off-by: Robert Marko <robimarko@gmail.com>
The MAC_FORCE_MODE_CTRL register is only used for the CPU port.
No need to repeat the port register calculation for each usage.
Simply point to the cpu port register directly.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22100
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use substr() instead of array index syntax to access the first
character of the endpoint host string, as ucode does not support
array-style indexing on strings.
Fixes: https://github.com/openwrt/openwrt/issues/22116
Fixes: 8f977b4a40 ("wireguard-tools: fix handling of multi-value config options")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
180ffcc instance: use mkdir_p helper
9493a3d signal: handle SIGUSR1 as halt
4dd22d0 cgroups: fix syntax error
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fixed the compilation of kernel with the loadable modules support turned off
Signed-off-by: Maksim Dmitrichenko <dmitrmax@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22041
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove unneeded includes from setup.c and adapt comments.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22084
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add missing CONFIG_LEDS_QCOM_LPG symbol.
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22096
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit 041ef9648d ("qualcommbe: move Device DTS to dedicated DTS
directory") introduced a dedicated DTS directory and set DEVICE_DTS_DIR
to ../dts as default. This broke the rdp433 device build since its DTS
resides in the kernel tree (applied via patches), not in the target dts
directory.
Fix this by overriding DEVICE_DTS_DIR for rdp433 to point to the kernel
DTS directory.
Fixes: 041ef9648d ("qualcommbe: move Device DTS to dedicated DTS directory")
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22096
Signed-off-by: Robert Marko <robimarko@gmail.com>
Config options like addresses and ip6prefix can be passed as either a
space-separated string or an array. Add a to_array() helper and use it
consistently for all multi-value options (addresses, ip6prefix,
allowed_ips).
Fixes: https://github.com/openwrt/openwrt/issues/22102
Fixes: 41bc454602 ("wireguard-tools: rewrite proto handler in ucode")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Due to confusing Documentation, the SPI and SLIC base clock and
register location for Airoha AN7583 SoC were wrong.
Fix them with new updated Documentation source to provide correct
clock support.
Fixes: c5b12fc02a ("airoha: Introduce support for Airoha AN7583 SoC")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Without initializing pwd_group, it's set to 0, which is reserved value.
When EAP-PWD is used in wpa_supplicant/eapol_test, next error is seen:
EAP-PWD: Server EAP-pwd-ID proposal: group=0 random=1 prf=1 prep=0
EAP-pwd: Unsupported or disabled proposal
Signed-off-by: Yaroslav Isakov <yaroslav.isakov@gmail.com>
Secondary BSSes inherit the alloc value which bypasses
NL80211_ATTR_VIF_RADIO_MASK in nl80211_create_iface() and causes the
kernel to default new interfaces to all radios.
The ucode bss_create fallback fails to correct this because
the interface is already UP.. the kernel rejects SET_INTERFACE with
-EBUSY.
Signed-off-by: Chad Monroe <chad@monroe.io>
Reuse Device/FitImage recipe instead of open coding it and
drop duplicate KERNEL_INITRAMFS recipe for eDPU.
While at it, lets clean up the boot script to drop uneeded console
setting, earlycon etc.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Move the Device/FitImage recipe to the generic image Makefile to avoid
duplicating it for other subtargets.
Will be used for uDPU/eDPU.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This allows to drop a family condition check and in the future
allows to merge nowadays splitted functions. While we are here
replace a hardcoded 0xc value with the new value for better
readability.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21999
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is enough info in the control and config structures to derive
the device specific counter freeing. No need to write two different
functions.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21999
Signed-off-by: Robert Marko <robimarko@gmail.com>
Get away with another family check.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21999
Signed-off-by: Robert Marko <robimarko@gmail.com>
During transmit the driver must adapt the packet length. The
hardware requires at least a memory space of ETH_ZLEN bytes
data plus four bytes for layer 2 FCS. This was calculated
(somehow) but skb->len never got updated and for the minimum
length a RTL838x specific workaround was in place. Clean up
the code and use skb_put_padto() so the length change gets
reflected in skb->len.
While we are here drop zeroing DSA tag because it will be
overwritten by hardware for FCS.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21999
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch from auto-scan PHY discovery to explicit DT-based registration
using fwnode_mdiobus_register_phy(). This is the standard approach used
by of_mdiobus_register() and most MDIO drivers.
Auto-scan (phy_mask-based) registration does not attach DT fwnode data
to PHY devices, which means DT properties like "pses" are never parsed.
As a result, PSE controllers referenced from PHY nodes are not linked,
and ethtool PSE commands (--show-pse, --set-pse) do not work.
Store the device_node for each PHY found during DT parsing, suppress
auto-scan by setting phy_mask to ~0, and register each PHY explicitly
after devm_mdiobus_register(). This allows fwnode_find_pse_control() to
resolve PSE references and also establishes proper fw_devlink supplier
relationships.
Additionally this fixes a bug where the RTL8221B is limited to
1G and below due to missing DTS references.
Fixes: 4e00306 ("realtek: mdio: use bus auto registration")
Signed-off-by: Carlo Szelinsky <github@szelinsky.de>
Link: https://github.com/openwrt/openwrt/pull/22019
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update cmake to version 4.2.3.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/22052
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for the Cisco Meraki MR70/Go GR60.
The Meraki MR70 is a Cisco 802.11ac/WiFi 5 outdoor AP with 1 Ethernet port.
It can be powered by a 12V DC barrel jack (5.5x2.5mm, center positive)
or via 802.3af POE.
The Meraki Go GR60 (codename: Dungbeetle Omni) is identical to the MR70
(codename: Toe Biter Omni), so this document will refer to both devices
as the MR70.
MR70 hardware info:
* CPU: Qualcomm IPQ4029
* RAM: 256MB DDR3
* Storage: 128 MB (TSOP48 NAND, 3.3V)
* Networking: 1 Gigabit Ethernet
* WiFi: QCA4019 802.11b/g/n/ac
* Serial: Internal header (J10, 2.54mm, unpopulated)
This device ships with secure boot, and cannot be flashed without
external programmers (TSOP48 NAND and I2C EEPROM)!
Disassembly:
Note: This is an outdoor device that is ultrasonically welded and glued
to weather seal it. Disassembly will compromise the weather seal!
Start by removing the product label on the rear metal mounting plate.
There are four Torx T8 screws under the sticker, remove the screws and
the mounting plate. Remove the two Philips screws under the plate.
Using a chisel (or razor blade) and hammer, cut around the circumfrence
of the device. You need to cut through approximately 2mm of
ultrasonically welded plastic.
After cutting through the plastic, heat the device using a hair drier
(or similar) to soften the glue. A heatgun is NOT recommended as
it will damage the plastic. It is only required to heat the device until
warm (~40C-50C).
Using a plastic pry tool, insert it along the cut you made around
the edge and gently separate. Insert a guitar pick into the opening
while gently lifting the front to cut the glue. The device is glued around
the entire circumfrence.
Once you have removed the plastic front, remove the 4 Philips screws
holding down the main PCB. Release the two WiFi antennas by gently
bending the antenna PCBs to the middle of the unit and pulling up.
Lift the top of the PCB gently while pushing the Ethernet port into the
housing to release it. Turn the PCB over and remove the three Philips
screws holding the metal heat spreader.
The TSOP48 NAND flash (U9, S34ML01G200 or W29N01HV) is located
under the metal heat spreader.
To flash, you need to desolder the TSOP48 or use a 360 clip.
You also need to reprogram the I2C EEPROM (U20, Atmel 24c64). It is not
necessary to desolder the I2C EEPROM, a ch341a USB programmer and SOP-8
clip are inexpensive (~$10) and work well.
Installation:
The dumps to flash can be found in this repository:
https://github.com/halmartin/meraki-openwrt-docs/tree/main/mr70_gr60
The device has the following flash layout (offsets with OOB data):
```
0x000000000000-0x000000100000 : "sbl1"
0x000000100000-0x000000200000 : "mibib"
0x000000200000-0x000000300000 : "bootconfig"
0x000000300000-0x000000400000 : "qsee"
0x000000400000-0x000000500000 : "qsee_alt"
0x000000500000-0x000000580000 : "cdt"
0x000000580000-0x000000600000 : "cdt_alt"
0x000000600000-0x000000680000 : "ddrparams"
0x000000700000-0x000000900000 : "u-boot"
0x000000900000-0x000000b00000 : "u-boot-backup"
0x000000b00000-0x000000b80000 : "ART"
0x000000c00000-0x000007c00000 : "ubi"
```
* Dump your original NAND (if using nanddump, include OOB data).
* Decompress `u-boot.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `u-boot` portion of NAND from
`0x738000`-`0x948000` (length `0x210000`). Offsets here include OOB data.
* Decompress `ubi.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `ubi` portion of NAND from
`0xc60000-0x7fe0000` (length `0x7380000`). Offsets here include OOB data.
* Dump your original EEPROM. Change the byte at offset `0x49` to `0x1e`
(originally `0x2d` or `0x26`). Remember to re-write the EEPROM with the
modified data.
* This can be done on Linux via the following command:
`printf "\x1e" | dd of=/tmp/eeprom.bin bs=1 seek=$((0x49)) conv=notrunc`
**Note**: the device will not boot if you modify the board major number and
have not yet overwritten the `ubi` and `u-boot` regions of NAND.
* Resolder the NAND after overwriting the `u-boot` and `ubi` regions.
OpenWrt Installation:
* After flashing NAND and EEPROM with external programmers. Plug in an
Ethernet cable and power up the device.
* The new U-Boot build uses the space character `" "` (without quotes) to
interrupt boot.
* Interrupt U-Boot and `tftpboot` the OpenWrt initramfs image from your
tftp server
```
dhcp
setenv serverip <your_tftp>
tftpboot openwrt-ipq40xx-generic-meraki_mr70-initramfs-uImage.itb
```
* Once booted into the OpenWrt initramfs, created the `ART` ubivol with
the WiFi radio calibration from the mtd partition:
```
cat /dev/mtd10 > /tmp/ART.bin
ubiupdatevol /dev/ubi0_1 /tmp/ART.bin
```
* `scp` the `sysupgrade` image to
the device and run the normal `sysupgrade` procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_mr70-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_mr70-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22050
Signed-off-by: Robert Marko <robimarko@gmail.com>
Underdog devices lack a red LED, use the blue LED for
failsafe mode.
Move all config except device name to underdog.dtsi, as
all known underdog devices (MR20/GR10, MR70/GR60) have identical
device tree.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22050
Signed-off-by: Robert Marko <robimarko@gmail.com>
Forward the OpenWrt CPPFLAGS to the compile process. This fixes fortify
sources support.
Link: https://github.com/openwrt/openwrt/pull/22056
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the OpenWrt CPPFLAGS to the CFLAGS. ebtables does not
support CPPFLAGS. This fixes fortify sources support.
Link: https://github.com/openwrt/openwrt/pull/22056
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the OpenWrt CPPFLAGS to the CFLAGS. arptables does not
support CPPFLAGS. This fixes fortify sources support.
Link: https://github.com/openwrt/openwrt/pull/22056
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the OpenWrt CPPFLAGS to the FLAGS. iwinfo does not support CPPFLAGS.
This fixes fortify sources support.
Link: https://github.com/openwrt/openwrt/pull/22056
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the OpenWrt CPPFLAGS to the CFLAGS. zyxel-bootconfig does not
support CPPFLAGS. This fixes fortify sources support.
Link: https://github.com/openwrt/openwrt/pull/22056
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Forward the OpenWrt CPPFLAGS to the compile process. This fixes fortify
sources support.
Link: https://github.com/openwrt/openwrt/pull/22056
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the OpenWrt CPPFLAGS to the CFLAGS. wireless-tools does not
support CPPFLAGS. This fixes fortify sources support.
Link: https://github.com/openwrt/openwrt/pull/22056
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Forward the OpenWrt CPPFLAGS to the compile process. This fixes fortify
sources support.
Link: https://github.com/openwrt/openwrt/pull/22056
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Forward the OpenWrt CPPFLAGS to the compile process. This fixes fortify
sources support.
Link: https://github.com/openwrt/openwrt/pull/22056
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Forward the OpenWrt CPPFLAGS to the compile process. This fixes fortify
sources support.
Allow to extend the CPPFLAGS and not only overwrite.
Link: https://github.com/openwrt/openwrt/pull/22056
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the OpenWrt CPPFLAGS to the CFLAGS. bzip2 does not support CPPFLAGS.
This fixes fortify sources support.
Link: https://github.com/openwrt/openwrt/pull/22056
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Forward the OpenWrt CPPFLAGS to the compile process. This fixes fortify
sources support.
Link: https://github.com/openwrt/openwrt/pull/22056
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Forward the OpenWrt CPPFLAGS to the compile process. This fixes fortify
sources support.
Link: https://github.com/openwrt/openwrt/pull/22056
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Forward the OpenWrt CPPFLAGS to the compile process. This fixes fortify
sources support.
Link: https://github.com/openwrt/openwrt/pull/22056
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Forward the OpenWrt CPPFLAGS to the compile process. This fixes fortify
sources support.
Link: https://github.com/openwrt/openwrt/pull/22056
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The sgmiisys0 override uses
/delete-node/ mediatek,pnswap;
but mediatek,pnswap is a property, not a child node. The correct
directive would be /delete-property/. As a result, this statement never
had any effect and the property was never removed.
Drop the incorrect override.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22046
Signed-off-by: Robert Marko <robimarko@gmail.com>
No code changes. Just some explanation how these devices
work with physical and logical memory.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22054
Signed-off-by: Robert Marko <robimarko@gmail.com>
NVMEM in UBI support has been present for a while. Use it to get the
MACs. Seems caldata needs to continue to be obtained through userspace.
This fixes label-mac-device as it needs a mac-address nvmem cell.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17068
Signed-off-by: Robert Marko <robimarko@gmail.com>
Follow the recent change where all DTS files were moved to a dedicated dir.
Fixes: 3a39f682df ("qualcommax: ipq50xx: add support for CMCC MR3000D-CI")
Signed-off-by: Robert Marko <robimarko@gmail.com>
