The ethernet driver configures the SoC internal network card
on its own. There are no special serdes or other layers in
between. So there is no need for pcs handling in the driver.
Drop that.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22347
Signed-off-by: Robert Marko <robimarko@gmail.com>
These devices contain a single MAC address in the U-Boot environment.
Set it as eth0 and label MAC in device tree. To maintain the current
state, the 02_network script still sets individual port MAC addresses
and the bridge MAC address.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22302
Signed-off-by: Robert Marko <robimarko@gmail.com>
Allow to convert MAC adddresses for all devices to NVMEM in
the future.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22302
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Cudy M3000 v1/v2 seem to have mostly identical hardware.
The M3000 v1 OpenWrt images work on the M3000 v2 (excluding
the v2 parts with a different PHY). Cudy also distributes one
firmware image that supports both routers.
Rename the human-readable device variant to "v1/v2" to match this.
Don't change the compatible property as that hooks into the
attended sysupgrade process.
The recent flash and PHY changes don't seem to be related to the v1/v2
split. There exist M3000 v2 with the Realtek PHY, see e.g.
https://github.com/openwrt/openwrt/pull/21584#issuecomment-3864992555
Signed-off-by: Jakub Vaněk <linuxtardis@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22259
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The hardware is very close the the Cudy M3000 v1 (see commit
20e4a18feb). However, the Motorcomm YT8821 PHY is tricky
to support because of a MDIO address collision within the router.
Specification:
- MT7981BA CPU: dual-core ARM Cortex-A53 @ 1.3 GHz
- 256 MiB RAM
- 128 MiB SPI NAND
- Ethernet:
- 1x 1GbE LAN port driven by the internal MT7981 PHY
- 1x 2.5GbE WAN port driven by the Motorcomm YT8821
- WiFi:
- MT7981BA 2.4 GHz WiFi with 2x2:2 MIMO
- MT7981BA 5 GHz WiFi with 2x3:2 MIMO
- Buttons: Reset, WPS
- LED: 1x combined red/white
How to know if you have the a router with the YT8821 PHY:
- Boot the router into the vendor's firmware. Go to Diagnostic Tools
-> System Log. Try searching for "rtl8221b".
- If there are some matches, you have the Cudy M3000 router with
the Realtek PHY and you should NOT use the device defined in this
commit. Instead, you should use the device defined in
mt7981b-cudy-m3000-v1.dts.
- If there are no matches, try searching for "yt8821". If that
matches something, you have the Cudy M3000 with the Motorcomm PHY
and you should use this device tree
(mt7981b-cudy-m3000-v2-yt8821.dts).
- If even the yt8821 string did not match anything, then something
is wrong. Rebooting the router might help (the system log would
be refreshed).
Installation via the Cudy web UI:
- Download the signed intermediary firmware from
https://drive.google.com/drive/folders/1BKVarlwlNxf7uJUtRhuMGUqeCa5KpMnj
- Flash the intermediary firmware using the Cudy web UI
- Connect a PC/laptop to the "1Gbps LAN" port
- Open http://192.168.1.1 in your browser, log in
(the password should be empty)
- Flash your desired OpenWrt firmware via LuCI
- The router should reboot into the desired firmware
How to access UART (citing from 20e4a18feb):
- remove rubber ring on the bottom
- remove screws
- pull up the cylinder, maybe help by push on an ethernet socket
with a screwdriver
- remove the (3) screws holding the board in the frame
- remove the board from the frame to get to the screws for the
silver, flat heat shield
- remove the (3) screws holding the heat shield
- solder UART pins to the back of the board
- make sure to have the pins point out on side with the black,
finned heat spread
- the markings for the pins are going to be below the silver heat
shield
- Vcc is not needed
- the UART parameters are 115200 baud, 8n1
Installation via UART (citing from 20e4a18feb):
- attach an Ethernet cable to the "1Gbps LAN" port on the router
- hold the reset button while powering the router
- press CTRL-C or wait for the timeout to get to the U-Boot prompt
- prepare a TFTP server on the network to supply ..-initramfs-kernel.bin
- use 'tftpboot 0x46000000 ..-initramfs-kernel.bin' in the U-Boot
shell to pull the image (change the file name accordingly)
- boot the image using 'bootm 0x46000000'
- push the ..-sysupgrade to the router using your preferred method
- perform the upgrade with 'sysupgrade -n'
Signed-off-by: Jakub Vaněk <linuxtardis@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22259
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
58eb263 instance: don't print error in case cgroups are disabled
9baf019 instance: use positive error numbers for strerror()
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The KSZ9477 driver was added to the cortexa53 kernel to support the
Gateworks Venice product family which has a board with this switch. Now
that the kmod-dsa-ksz9477 driver is available as a package remove the
static configuration ad add the package.
This resolves an issue caused by having the switch driver static and the
PHY driver as a module such that the PHY driver was not registered early
enough to be used causing some errata to not be worked around.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/22120
Link: https://github.com/openwrt/openwrt/pull/22257
Signed-off-by: Robert Marko <robimarko@gmail.com>
This adds kernel packages for the Microchip KSZ9477 switch family.
The core package has a target specific dependency as the ksz9477
driver enables DCB which grows the kernel size and can negatively
impact other targets.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/22257
Signed-off-by: Robert Marko <robimarko@gmail.com>
Makes it clear that the allocation is dealing with a flex array member.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21960
Signed-off-by: Robert Marko <robimarko@gmail.com>
In generic, there's a backport from 6.14 that makes this change. Do so
in downstream locations as well.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21167
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is nearly identical to what landed in ath-next for v7.1, aside from
resolving a couple conflicts. A separate patch has been added to replace
CONFIG_THERMAL with CPTCFG_ATH12K_THERMAL so the setting may be enabled
via menuconfig (as is done with ath10k and ath11k).
Note that at this stage, throttling has not been implemented upstream,
hence the slight change in wording versus existing options.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.6-01243-QCAHKSWPL_SILICONZ-1
Link: https://patch.msgid.link/20260223132622.43464-1-maharaja.kennadyrajan@oss.qualcomm.com
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/22280
Signed-off-by: Robert Marko <robimarko@gmail.com>
Restore the lost band label.
Fixes: 502ac21e8f ("ipq40xx: drop redundant label with new LED color/function format")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
22fb70661799 fix flex array not at end of struct
6a5c4716ca25 convert memcpy + ETH_GSTRING_LEN to ethtool_puts
Signed-off-by: Robert Marko <robimarko@gmail.com>
a52cdb354d13 dns: validate IPv4 record addresses
b798c24205b5 dns: validate IPv6 record addresses
a3dcb4adc635 dns: validate reverse dns query name lengths
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
SFP I2C buses for ports 1 and 3 were swapped as order changed on production
boards.
So, swap them around to fix SFP 1 and 3 failed to read EEPROM errors.
Fixes: 29b3d929a6 ("microchipsw: lan969x: add Novarq Tactical 1000")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Check for malformed artifact names before dereferencing them.
Fixes: 5816d883ff
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22385
Signed-off-by: Robert Marko <robimarko@gmail.com>
I wrongly added the wifi devices to the pcie nodes and not the bridge
nodes as they were not present at the time.
Fixes: 58056df ("bcm53xx: backport nvmem mac for meraki mr26")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22369
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove source-only from an7581.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17869
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Most, if not all Airoha devices will have LEDs and buttons. Add them to
default packages.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17869
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add uboot-envtools to default packages to facilitate modifying the
u-boot environment.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17869
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This commit adds support for Gemtek (Centurylink/Lumen/Quantum Fiber)
W1700K.
Device specification
--------------------
SoC Type: Airoha AN7581
RAM: ESMT M16U8G16512A (2GB)
Flash: Winbond 25N04KVZEIR (512MB)
Ethernet: 2x gigabit via AN7581, 2x 10g via RTL8261N
Wi-Fi: MT7996 - BE19000
LEDs: 1 LED, power/status
Button: Reset
USB ports: None
Bootloader: U-Boot 2014.04-rc1 (Jun 12 2024 - 08:14:34) AXON 2.0
Fan: 1x controlled by Nuvoton NCT7511Y
This device is pretty useless with the stock firmware as it requires an
account to completely set it up. Additionally, the vendor bootloader is
signed and uses Airoha/Mediatek's BBT/BMT for bad block management on
the flash. It does not support UBI, thus kernel updates are subject to
BMT/BBT which OpenWrt does not support. In turn, if a kernel update
happens and a block is marked bad in the process, the device will fail
to boot and will need to be recovered via serial.
The workaround is to chainload U-Boot in place of the kernel, as it
should not need frequent updates and thus should not cause BBT/BMT to
misbehave and soft-brick the device. Upstream U-Boot supports loading
a FIT image from UBI, so we create a UBI partition for the new u-boot
env, FIT image and factory data. This way, bad blocks are managed by UBI
instead, which will not soft-brick the device should a block be marked
bad during a normal OpenWrt update. Users wishing to update U-Boot can
do so, but should be prepared to recover if a block goes bad.
Because the device is not useful with stock firmware, this is a one-way
ticket for most users and reverting will not be documented.
The following steps can be used to install OpenWrt on the W1700K.
Connect to serial console. There is a Torx T10 screw underneath the QR
code printed onto the label. Then, pry between the gray and white
plastic, starting by the ports on the back. There are clips arount the
entire device. Starting closest to the screw next to the UART header,
TX - GND - VCC - N/A - RX. The bootloader can be interrupted by
pressing any key.
Configuring Vendor Bootloader and Installing U-Boot Chainloader:
The bootloader's default bootcmd will only run a signed image. However,
we can still bootm our own image from flash.
NOTE: The vendor's ethernet drivers are flaky. You may have to reboot
and try the tftpboot part several times for it to work.
- setenv one flash read 0x600000 0x1000000 \$loadaddr
- setenv two "; bootm"
- setenv bootcmd "$one$two"
- setenv one
- setenv two
- saveenv
- setenv serverip 192.168.1.10; setenv ipaddr 192.168.1.1; tftpboot
0x89000000 openwrt-airoha-an7581-gemtek_w1700k-ubi-chainload-uboot.itb
- flash erase 0x600000 0x100000
- flash write 0x600000 0x100000 0x89000000
- reset
The device will now reboot into the U-Boot chainloader.
Loading the W1700K UBI Installer:
The installer can be downloaded at
https://github.com/hurrian/w1700k-ubi-installer/releases
- Boot the installer via the TFTP option in the U-Boot menu. This
process is automatic, though you may be prompted to answer some
questions.
- Once it is done, you may upgrade to your preferred build.
- For more information: https://github.com/hurrian/w1700k-ubi-installer
For those wishing to explore the stock firmware:
Rooting Stock FW (for making backups, recommended):
- Boot the router and watch serial console until presented with failsafe
mode. Enter it (f + enter).
- mount_root
- Change the root password (passwd).
- Open /etc/config/axon_platform_manager and set sshServerEnable,
localAccessEnable and remoteAccessEnable to 1.
- Search for "SSH". You'll find a long string with 3 matches such as
Enabled%25252c1%25252cSSH%Drop. Change any instances of "Disabled"
preceding SSH to "Enabled" and any instances of "Drop" to "Accept"
that follow SSH. Same for "Local SSH" and "Remote SSH".
- Set /etc/config/dropbear to:
config dropbear
option PasswordAuth 'on'
option RootPasswordAuth 'on'
option Port '22'
- Reboot.
- Connect 10g WAN port to existing network and SSH in with the password
you set.
- SSH into rooted stock fw.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17869
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In the transition to nvmem-layout and subsequent disabling of non layout
u-boot-env, this device was left out.
Transition to nvmem-layout to fix the mac address.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22263
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Userspace handling is deprecated.
These are identical to NBG6617, which was tested as working.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22263
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Userspace handling is deprecated.
UBI nvmwem has been supported for quite a while now.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22263
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
When NVMEM is not ready, of_get_mac_address fails. Handle this.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22305
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
When NVMEM is not ready, of_get_mac_address fails. Handle this.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22305
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Like a STAGING_SUBDIR_TARGET which uses TARGET_DIR_NAME, we can use TOOLCHAIN_DIR_NAME for STAGING_SUBDIR_TOOLCHAIN to avoid code duplication.
Signed-off-by: Nikita Ostrenkov <ownik.dev@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22315
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
RTL838x devices cannot reboot if the flash controller is driven in
4 byte mode. Unitl fdc3776 ("realtek: pcs: fix PLL_CML_CTRL for
serdes 0/1") this bit was luckily cleared by a coding error. Since
then the device cannot be rebooted anymore.
Looking at the SDK one can see that this bit is reset short before
the reboot happens. But we might need that in critical situations
where there is no chance to do it right in time. As the RTL838x
always ran with the bit disabled restore the old behaviour. This
time implement it as a documented quirk so it does not get lost.
Fixes: fdc3776 ("realtek: pcs: fix PLL_CML_CTRL for serdes 0/1")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22334
Signed-off-by: Robert Marko <robimarko@gmail.com>
When the virtual package "uci-firewall" is installed, the choice
between "firewall" and "firewall4" is arbitrary, sometimes resulting
in one, sometimes the other.
Set the default variant on "firewall4" to make it the preferred
package when installed as a dependency.
Link: https://forum.openwrt.org/t/owut-openwrt-upgrade-tool/200035/1126
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22328
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Disable airoha-flow-stats for an7583 since it is not currently supported
by the firmware image.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/22341
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Instead of directing users to the useless 'man 8 apk', we direct
them to the wiki help page.
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22271
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Realtek DSA driver accesses the DTS at two locations.
- rtldsa_ethernet_loaded(): to check if ethernet driver is active
- rtl83xx_mdio_probe(): to create ports and link to pcs/phy
The first function does not directly search for the ethernet driver
but looks it up through the switch port nodes. Avoid future issues
and simply search all nodes that have a "ethernet" link to the
network driver.
While we are here add a missing put_device() to keep reference
counters clean.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22235
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
rteth_930x_create_tx_header() and rteth_931x_create_tx_header() do
basically the same. Only exception is, that one function can handle
ports beyond 32 and the other not. Merge them into one.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22228
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
