They are being default enabled unconditionally when they should
depend on 802.11k. 802.11k should not be enabled by default
either as it can cause issues with certain older drivers and
is useless without a userspace program like usteer or DAWN.
If users want to enable 802.11k they will enable it when they
set such programs up.
Another inconsistency with rnr was dealt with so that it is not
default enabled. This is also not done with old wifi-scripts
and is generally unexpected and surprising behavior.
Moreoever, this introduces an inconsistency between old shell
wifi-scripts and ucode version. Old wifi-scripts does not do this.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/21425
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit ee60b65643)
These patches were actually merged in kernel 6.19 instead of 6.18,
fix them to avoid confusing when moving to new kernel version.
While at it, refresh the RK3528 PCIE L1ss patch since it was
accepted in 6.19 as well.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/21419
(cherry picked from commit c79fa27cbf)
Link: https://github.com/openwrt/openwrt/pull/21448
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, kmod-crypto-kpp is only implied for curve25519 and thus it
can get unselected and then building will fail due to missing kpp.ko.
Same issue happens with kmod-crypto-hash for poly1305.
So, lets drop the whole implies logic and make sure to always select
them as dependencies.
Fixes: #21386
Link: https://github.com/openwrt/openwrt/pull/21483
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 93665d0aa3)
When DHCP Option 60 is specified via sendopts (hex, decimal, or named
formats), udhcpc sends its default "udhcp <version>" string alongside
the custom value, which causes authentication failures with some ISPs.
This fix detects Option 60 in sendopts and automatically passes -V ""
to udhcpc to suppress the default version string while allowing
multiple user-defined vendor classes.
Supported formats:
- Hexadecimal: 0x3c
- Decimal: 60
- Named: vendor
(cherry picked from commit 89d982d723)
Fixes: #21242
Signed-off-by: JINLIANG GU <ihipop@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21450
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Novarq Tactical 1000 is a LAN9696 based switch.
Specifications:
* CPU: Microchip LAN9696 switch SoC
* DRAM: 2GB DDR4
* Storage:
* 32MB QSPI NOR
* 16GB eMMC
* Networking:
* 24 x 10/100/1000 RJ45 via LAN8804 Quad PHY-s over QSGMII
* 4 x 100/1000/2500/5000/10000 SFP+ ports
* 1 x 10/100/1000 management RJ45 via LAN8840 PHY over RGMII (U-Boot too)
* USB: 1 x USB2.0 Type-A
* Management via USB-C (MCP2200):
* UART @ 115200 baud (Default), 921600 possible
* GPIO-s for bootstrap and reset
* LED-s:
* 2 per networking port (Green and Yellow)
* Green status LED
* Soft reset GPIO
* Power: 12V DC barrel jack
* External PoE:
* Option for PoE add-on
* Temperature Sensors:
* TMP1075 onboard
* CPU temperature
* Microchip MCP79402 RTC with battery back-up
* Microchip ATECC608C secure peripheral
* CPU heatsink with PWM fan
* Onboard header for case fan
Installation instructions:
1. Connect to UART via the USB-C port
2. Connect the management port
3. Boot and interrupt U-Boot
4. TFTP the OpenWrt initramfs image and boot it
5. SCP the OpenWrt eMMC GPT image to a running OpenWrt initramfs to /tmp
openwrt-microchipsw-lan969x-novarq_tactical-1000-squashfs-emmc-gpt.img.gz
And decompress it via:
gzip -d /tmp/openwrt-microchipsw-lan969x-novarq_tactical-1000-squashfs-emmc-gpt.img.gz
6. Wipe eMMC with:
dd if=/dev/zero of=/dev/mmcblk0 bs=1M
7. Flash OpenWrt eMMC image with:
dd if=/tmp/openwrt-microchipsw-lan969x-novarq_tactical-1000-squashfs-emmc-gpt.img
of=/dev/mmcblk0
After a restart OpenWrt will boot, and then regular sysupgrade can be used
for upgrades.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 29b3d929a6)
Replace some of the pending patches with the upstreamed versions and mark
them accordingly.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 7b7a559976)
Update microchipsw TF-A to the latest bugfix release that fixes
SHA checksum validation if large files are uploaded via the monitor mode.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 6e0379deb9)
Use the latest v3 that is sent upstream, it now uses a DTS header for clock
indices.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 6944f1c6a0)
BDF for EAP623-Outdoor HD v1 was renamed in the repo, but ipq-wifi
was not updated to reflect that, so do it now to fix broken wifi.
Fixes: #21432
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 0ff1553bd7)
These patches fix bugs in a patch we backported.
These patch were cherry picked from upstream Linux because it references
a patch we backported in the fixes tag.
The patches were reordered to match the ordering in the upstream Linux kernel.
Fixes: 93173aee96 ("qualcommbe: ipq95xx: Add initial support for new target")
Link: https://github.com/openwrt/openwrt/pull/21366
(cherry picked from commit 5230157a16)
Link: https://github.com/openwrt/openwrt/pull/21390
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes a bug in a patch we backported.
This patch was cherry picked from upstream Linux because it references a
patch we backported in the fixes tag.
The first two patches are providing function needed by the last patch.
Fixes: 813ecda1f3 ("generic: backport phylink patches for PCS/PHY caps OPs")
Link: https://github.com/openwrt/openwrt/pull/21366
(cherry picked from commit 69d76e3a14)
Link: https://github.com/openwrt/openwrt/pull/21390
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes a bug in a patch we backported.
This patch was cherry picked from upstream Linux because it references a
patch we backported in the fixes tag.
The function phy_id_compare_vendor() is needed by the fix.
Refresh 782-05-v6.16-net-phy-Add-support-for-Aeonsemi-AS21xxx-PHYs.patch with the upstream code.
Fixes: 08a616b216 ("generic: backport support for Aeonsemi AS21xxx PHY")
Link: https://github.com/openwrt/openwrt/pull/21366
(cherry picked from commit b3318fe819)
Link: https://github.com/openwrt/openwrt/pull/21390
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Linksys MX6200 is a triband Wi-Fi 6E wireless router.
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Nanya NT5CC256M16ER-EK (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
QCN6122 (2x2:2 6 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to:
- LAN Port: Internal IPQ5018 GE PHY
- WAN Port: Maxlinear Ethernet GPY115C PHY
* Flash: Macronix MX35UF2GE4AD (256 MiB)
* LEDs: 1x multi-color PWM LED
* Buttons: 1x WPS (GPIO 27 Active Low)
1x Reset (GPIO 28 Acive Low)
* FCC ID: 2AYRA-08436
Flash instructions:
************************************************************************
NOTE: serial access is required! Although the web UI allows you to
install the Openwrt image, secure boot is enabled which will prevent
booting an unsigned image. The boot sequence must be adjusted in U-boot
to allow booting unsigned images.
************************************************************************
1. On OEM firmware, login to the web UI (typically @ http://192.168.1.1)
and click 'CA' in the bottom right corner.
Then click -> Connectivity -> Manual Upgrade.
Alternatively, browse to
http://<router IP>/fwupdate.html.
Upload openwrt-qualcommax-ipq50xx-linksys_mx6200-squashfs-factory.ubi.
Continue with step 5.
2. Installation on alternate partition using serial connection from OEM
firmware (default login: root, password: admin):
flash_erase /dev/mtd19 0 0
nandwrite -p /dev/mtd19 openwrt-qualcommax-ipq50xx-linksys_mx6200-squashfs-factory.ubi
reboot
Continue with step 5.
3. Installation using serial connection from initramfs
setup tftp server listening on IP in 192.168.1.0/24 (other than the
router IP 192.168.1.1). In U-boot, load the initramfs image to memory:
tftp $loadaddr <your IP>:openwrt-qualcommax-ipq50xx-linksys_mx6200-initramfs-uImage.itb
boot the image using command:
bootm $loadaddr
when fully booted, scp the sysupgrade image to your router IP (default:
192.168.1.1):
scp -O <path>/openwrt-qualcommax-ipq50xx-linksys_mx6200-squashfs-sysypgrade.bin root@192.168.1.1:/tmp/
use sysupgrade to flash the image to nand:
sysupgrade -n -v /tmp/openwrt-qualcommax-ipq50xx-linksys_mx6200-squashfs-sysupgrade.bin
Continue with step 5.
4. Optionally install on alternate partition. From Openwrt:
mtd -r -e rootfs_1 -n write openwrt-qualcommax-ipq50xx-linksys_mx6200-squashfs-factory.ubi rootfs_1
Continue with step 5.
5. Setup U-boot for ability to dual boot signed (stock) and non-signed
(Openwrt) images with auto-detection.
From U-boot, run (be aware: copy line by line):
setenv setnandbootargs 'setenv bootargs init=/sbin/init ubi.mtd=rootfs rootfstype=squashfs rootwait'
setenv nandinitcmd 'setenv mtdids nand0=nand0; run setrootfscmd; ubi part rootfs 2048'
setenv setrootfscmd 'if test $boot_part = 1; then setenv mtdparts mtdparts=nand0:0x${imgsize}@0x${prikern}(rootfs); else setenv mtdparts mtdparts=nand0:0x${imgsize}@0x${altkern}(rootfs); fi'
setenv readhdr1cmd 'ubi read $loadaddr kernel 0x40; setexpr IMGOFF $loadaddr + 0x10; setexpr CODEOFF $loadaddr + 0x14; setexpr SIGOFF $loadaddr + 0x1c; setexpr CERTOFF $loadaddr + 0x24'
setenv readhdr2cmd 'setexpr.l HDR *$loadaddr; setexpr.l IMGSZ *$IMGOFF; setexpr.l CODESZ *$CODEOFF; setexpr.l SIGSZ *$SIGOFF; setexpr.l CERTSZ *$CERTOFF; setexpr TSIZE $CODESZ + $SIGSZ; setexpr TSIZE $TSIZE + $CERTSZ'
setenv testmbncmd 'if test $HDR -ne edfe0dd0 -a $IMGSZ -eq $TSIZE; then bootipq; else ubi read $loadaddr kernel $kernsize; run setnandbootargs; bootm $loadaddr; fi'
setenv bootcmd2 'if test $auto_recovery = no; then bootipq; else run nandinitcmd; run readhdr1cmd; run readhdr2cmd; run testmbncmd; fi'
setenv bootcmd 'run bootcmd2'
saveenv
6. Back to the OEM firmware.
Download firmware from OEM website:
MX6200: https://support.linksys.com/kb/article/408-en/
From serial/SSH, in Openwrt, flash OEM firmware to alternate partition:
mtd -r -e rootfs_1 -n write FW_MX6200_1.0.11.216041_prod.signed.img rootfs_1
Switching active partition:
1. From U-boot, executive the following to switch to partition 1:
setenv boot_part 1
for partition 2:
setenv boot_part 2
2. From Openwrt:
fw_printenv boot_part
In case it's 1:
fw_setenv boot_part 2
. /lib/upgrade/platform.sh
linksys_bootconfig_set_primaryboot "0:bootconfig" 1
linksys_bootconfig_set_primaryboot "0:bootconfig1" 1
In case it's 2:
fw_setenv boot_part 1
. /lib/upgrade/platform.sh
linksys_bootconfig_set_primaryboot "0:bootconfig" 0
linksys_bootconfig_set_primaryboot "0:bootconfig1" 0
and
reboot
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21038
Link: https://github.com/openwrt/openwrt/pull/21273
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for upgrades on dual firmware Linksys devices with the
partition table stored in SMEM and that store both the kernel and rootfs
in a single partition. Switching the active boot partition requires
updating the partition info table in SMEM in addition to setting
the active boot partition in a U-boot variable as U-boot will keep them
in sync upon reboot if they're not.
U-boot always sets the name of the active partition to rootfs and that
of the inactive partition to rootfs_1 in SMEM. when Linux loads the
partition table from SMEM it will load the right partition based on the
offset set in the SMEM partition table. For upgrades, flashing to the
alternate partition will always be to rootfs_1, while flashing the
current partition will be on rootfs.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21038
Link: https://github.com/openwrt/openwrt/pull/21273
Signed-off-by: Robert Marko <robimarko@gmail.com>
The BOOTCONFIG partition is used by Qualcomm's boot chain to store
metadata about the device's startup configuration. It contains info such
as versioning, configuration flags, primary boot partition, and more.
Newer devices with dual boot partitions not only store the active boot
partition in a U-boot variable but also in partition info in the
BOOTCONFIG partition. As such, add library functions to set and toggle
the active boot partition.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21038
Link: https://github.com/openwrt/openwrt/pull/21273
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move setting kernel bootargs from the base template down to the
respective Linksys board files. This allows for having devices which
require different bootargs use the base template device tree file.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21038
Link: https://github.com/openwrt/openwrt/pull/21273
Signed-off-by: Robert Marko <robimarko@gmail.com>
The partition table on Linksys devices with a Qualcomm AX IPQ SoC is
stored in SMEM. As such, load partition table from SMEM rather than
statically defining them in their respective device trees. This helps
generalize the base template and requires less maintenance.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21038
Link: https://github.com/openwrt/openwrt/pull/21273
Signed-off-by: Robert Marko <robimarko@gmail.com>
Mesh mode interface creation fails when the freq parameter is empty or
undefined. Unlike adhoc mode which checks if freq exists before using it,
mesh mode blindly constructs the iw command with freq parameter, resulting
in invalid syntax like:
iw dev mesh0 mesh join ssid freq NOHT
This causes the mesh interface to be created without joining the mesh
network, leaving it in a DOWN state with no channel assigned.
Fix by adding freq validation check similar to adhoc mode.
Tested on two routers in parallel as mesh peers:
- Xiaomi AX3000T (MediaTek MT7981)
- OpenWrt One (MediaTek MT7981)
- OpenWrt 6.6.119, 802.11s mesh on 5GHz (Channel 36, HE80)
Signed-off-by: Valent Turkovic <valent@meshpointone.com>
Link: https://github.com/openwrt/openwrt/pull/21373
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7214acd759)
The for-in loop variable 'name' was shadowing the function parameter,
causing remote subscription cleanup to fail when hosts disconnect.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit e782341848)
This allows us to use the full size of nand,
which extends ubi size from 64Mb to 122.25Mb.
If you are at factory firmware, please refer
to [PR](https://github.com/openwrt/openwrt/pull/21141)
to boot into OpenWrt first.
1. Log in to the device and backup all the partitions,
especially unique `Factory` and `bdata` partitions
from System -> Backup / Flash Firmware -> Save mtdblock contents.
2. Install kmod-mtd-rw to unlock mtd partitions for writing:
```bash
apk update && apk add kmod-mtd-rw && insmod mtd-rw i_want_a_brick=1
```
3. Write new OpenWrt (U-Boot Layout) `BL2` and `FIP`:
```bash
mtd write openwrt-mediatek-filogic-cudy_wbr3000uax-v1-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cudy_wbr3000uax-v1-ubootmod-bl31-uboot.fip FIP
```
4. Set static IP on your PC: `192.168.1.254`, gateway `192.168.1.1`
5. Serve openwrt-mediatek-filogic-cudy_wbr3000uax-v1-ubootmod-initramfs-recovery.itb
using TFTP server.
6. Connect Router LAN with PC LAN.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt initramfs recovery has booted,
clean `/dev/mtd5` ubi partition to utilize maximum of free space & create ubootenvs:
```bash
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
```
4. Perform sysupgrade.
Tested-by: 4pda users
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21225
(cherry picked from commit 15df98f3b5)
Link: https://github.com/openwrt/openwrt/pull/21342
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Another OEM variation of a Cudy WR3000 series device made for Russian market.
Hardware:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB GigaDevice SPI NAND. Flash Model: F50L1G41LB, ID: C801
- RAM: DDR3, 512 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- 1x WAN MT7531 (JXD 2531Z) 10/100/1000 Mbps
- 4x LAN 2x MT7530 (JXD 2529S) 10/100/1000 Mbps
- USB 3.0 port
- Buttons: Reset, WPS
- 8x LEDs: 2x Red, 6x Blue
- Serial console: no need to solder, just open the case and unskrew the radiator, TX-RX, RX-TX, GND-GND, VCC do not connect, 115200 8n1
- Power: 12 VDC, 1.5 A
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:AF:CA:xx:xx:x1 | label+1 |
| LAN | 80:AF:CA:xx:xx:x0 | label |
| WLAN 2g | 80:AF:CA:xx:xx:x0 | label |
| WLAN 5g | 82:AF:CA:xx:xx:x1 | label+1 |
+---------+-------------------+-----------+
Based on a factory layout with only 64mb partition for easier transition from factory to OpenWrt for users if the "intermediate" RSA signed firmware will be provided by Cudy.
**Installation**
The installation must be done via UART & TFTP by disassembling the router. On other occasions Cudy has distributed intermediate firmware and dts to make installation easier, but since this router is OEM special WB order for local RU market there is a possibility they will not provide it.
**Install using UART & TFTP**
1. Connect to UART.
2. Since the factory BL is locked and the boot process can not be stopped, you have to use mtkuartboot, hold reset, engage the power, boot into your payloaded bl2 & fip.
3. Connect to LAN and set your IP to 192.168.1.254.
4. Configure a TFTP server to serve openwrt-mediatek-filogic-cudy_wbr3000uax-v1-initramfs-kernel.bin file.
5. Run these steps in u-boot using the name of your file:
```
setenv bootfile openwrt-mediatek-filogic-cudy_wbr3000uax-v1-initramfs-kernel.bin
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.254
tftpboot
bootm
```
6. Router will boot into OpenWrt initramfs recovery, just open your browser `192.168.1.1` and sysupgrade with the `Keep settings` option turned off.
Tested-by: many 4pda users
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21225
(cherry picked from commit d7d6faf26f)
Link: https://github.com/openwrt/openwrt/pull/21342
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since there are many similar devices from Cudy (TR3000 / WR3000E / WR3000P / WR3000S / WBR3000UAX) this will allow to create OpenWrt U-Boot layout for all of them using same DDR3 target.
Tested-by: 4pda users
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21225
(cherry picked from commit f4c9ab6591)
Link: https://github.com/openwrt/openwrt/pull/21342
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The GS110TUP's lan9 port is connected via a QSGMII PHY to SERDES 2, and
therefore should use the SWITCH_PORT_SDS macro instead of SWITCH_PORT. This
was missed in e956adfe because the GS110TUP is not particularly well
documented and the old code was confusing.
lan10 is an SFP and doesn't have an onboard PHY, so also remove its
associated PHY references and update it to match other devices' SFP ports.
Fixes: https://github.com/openwrt/openwrt/issues/21324
Signed-off-by: Jacob Potter <jacob@j4cbo.com>
Link: https://github.com/openwrt/openwrt/pull/21346
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b2c0182f26)
Inadvertently defining 'DEFAULT_VARIANT' on both ethool and
ethtool-full variants resulted in
$ make defconfig
tmp/.config-package.in:121615:error: recursive dependency detected!
tmp/.config-package.in:121615: symbol PACKAGE_ethtool-full is selected by PACKAGE_ethtool
tmp/.config-package.in:121605: symbol PACKAGE_ethtool depends on PACKAGE_ethtool-full
Fix this by simply undefining 'DEFAULT_VARIANT' on the ethtool-full
variant, which is ugly, but expedient.
Fixes: https://github.com/openwrt/openwrt/commit/f4fdb996
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21363
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 7a78dc4a5d)
Some packages with variants did not specify the default among the
alternatives, so were left without any apk 'provider_priority'
for that package. This caused the apk solver to select the wrong
variant, silently changing the requested package list.
Notable among these were busybox, procd and the hostapd/wpad suite.
This behavior presented in the imagebuilders when creating the
image as follows, silently replacing packages even when explicitly
requested:
$ make image PACKAGES=busybox
...
( 14/148) Installing busybox-selinux (1.37.0-r6)
...
We add 'DEFAULT_VARIANT:=1' to the packages that were missing one,
providing apk with sufficient information to choose the correct
package.
See link below for further examples and discussion.
Link: https://github.com/openwrt/openwrt/pull/21288#issuecomment-3704101422
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21358
(cherry picked from commit f4fdb9964a)
Link: https://github.com/openwrt/openwrt/pull/21355
Signed-off-by: Robert Marko <robimarko@gmail.com>
