Every devices of mpc85xx was switched to DSA.
Swconfig can be removed.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22161
Signed-off-by: Robert Marko <robimarko@gmail.com>
Convert the P2020RDB DTS to DSA for the VSC7385 switch, add port
labels and fixed-link. Update board network defaults, preinit iface,
and compat version, and include the DSA switch kmod in the image.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22161
Signed-off-by: Robert Marko <robimarko@gmail.com>
A phy node in the dts has two properties:
- reg: the (overall) address of the phy
- realtek,smi-address: the address of the phy on its bus
This notation does not align with upstream. reg should be the address
of the phy on its bus. But where to get the overall address that is
needed for register writes to the hardware?
Luckily the mdio driver and the hardware design sync the ports and
phys (overall) addresses. Thus derive missing data from the dts port
nodes (below ethernet-ports). To realize this
- carve out the port mapping into a separate function to align with
the upstream driver.
- do more sanity checks and catch more inconsistencies
- raise more/better errors via dev_err_probe()
With this commit all dts files must be rewritten as follows:
- if phy has no realtek,smi-address leave it as is
- if phy has realtek,smi-address, write that value into the reg
property and drop realtek,smi-address.
Remark: This commit might bring some confusion about the phyXX and
phy@YY and <reg=YY> naming convention. To be somehow consistent with
the current port/phy identifiers from now on the dts will have:
- phyXX: where XX matches the port number
- phy@YY: where YY is the phy address on the mdio bus
- <reg=YY>: where YY is the phy address on the mdio bus
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22236
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
The switch node is currently located outside of the switchcore@1b000000
tree. This makes it hard to find when referencing from other nodes in
this tree. Make it a subnode of switchcore and "retype" it to
ethernet-switch like upstream does.
This is not perfectly aligned as upstream just mixes the switchcore and
the ethernet-switch node into one. But this will be future work for
downstream.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22236
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
The Zyxel XGS1x10 DTS overzealously tries to avoid redundancies. For
this the phy24/phy25 definitions were split into a common and a device
specific part. Understanding how these phys are defined is therefore
a little bit tricky. Add a little bit of redundancy to make the
definitions easier to read and understand in a single location.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22236
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
NN6000v1 Specifications:
SoC: Qualcomm IPQ6000 1.2GHz
RAM: K4B4G1646E-BCMA 512MiB x2 = 1 GiB
Flash: FORESEE 256GB eMMC
ETH: QCA8075 (2x LAN, 1x WAN)
WLAN1: QCN5022 2.4GHz AX 2x2
WLAN2: QCN5052 5GHz AX 2x2
Power: DC 12V
Button: Reset, Wps
USB: 1x 3.0
NN6000v2 Specifications:
SoC: Qualcomm IPQ6000 1.2GHz
RAM: MT41K512M16VRN-107 IT:P 1GiB x2 = 2 GiB
Flash: FORESEE 256GB eMMC
ETH: QCA8075 (4x LAN, 1x WAN)
WLAN1: QCN5022 2.4GHz AX 2x2
WLAN2: QCN5052 5GHz AX 2x2
Power: DC 12V
Button: Reset, Wps
USB: 1x 3.0
Install via UART:
1. Download the initramfs image, rename it to
initramfs.itb, host it with the tftp server.
2. Interrupt U-Boot and run these commands:
tftpboot initramfs.itb
bootm
3. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Install via Uboot WebUI:
- Only work when you flash a custom uboot with webui
- Push the reset button for 5 seconds, then use broswer to
access http://192.168.1.1/, then upload factory.bin.
Signed-off-by: Fire Chen <firedevel@icloud.com>
Link: https://github.com/openwrt/openwrt/pull/21787
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
NVMEM on MMC was added in dts but the corresponding option was not added
to the config.
Fixes: ee5999c ("treewide: linksys: use nvmem MAC for hw_mac_addr")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22539
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
The issue described in the patch has been fixed by commit
604355e8c4 ("kernel: fix fraglist GRO on linux 6.12")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22525
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
The initial mt76x8 kernel config file was inherited from mt7620
sub-target. However, This SoC series doesn't support any external
PHY. We can disable CONFIG_ICPLUS_PHY symbol to reduce kernel size.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22519
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport more upstream patch to include all the fixes pushed upstream and
add all the preliminary patch for multi-serdes support.
While at it also move 2 patch in the 6xx numbering to the 000-1xx backport
numbering to keep things tidy.
All the affected patch manually and automatically refreshed.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
[ add comment, renumber patch, add more patch, fix PCS patch ]
Link: https://github.com/openwrt/openwrt/pull/22479
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport new field_prep()/get() particularly useful to handle case where a
bitmask is not const and FIELD_PREP can't be used. This permit to replace
manual shift with these macro. (also needed to permit backport of some
patch without modification)
Backport reworked patch that drop the local field_prep()/get() macro in
favor of the global one.
Link: https://github.com/openwrt/openwrt/pull/22479
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Renumber ASoC and PCS patch to 2xx and 3xx numbering to leave space for
more backport patch in the 000-1xx numbering.
Link: https://github.com/openwrt/openwrt/pull/22479
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
These targets seems to be left over, so changed as other targets
covered by commit d35d92a .
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/22510
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for RTL9607C/RTL8198D clocks to the existing
clk-rtl83xx driver. Setting clock rates is not supported due to
lack of knowledge on this topic at the moment. Clocks for CPU1, SRAM
and SPI can also be calculated but not included in this commit.
Since the registers, calculations are widely different to RTL83XX it
was decide to have different clk_ops for RTL960X.
The code was partly based on naseef's work with some changes to
integrate it into the clk-rtl83xx driver.
Tested-by: Ahmed Naseef <naseefkm@gmail.com>
Signed-off-by: Rustam Adilov <adilov@tutamail.com>
Link: https://github.com/openwrt/openwrt/pull/22080
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, devices having two cpu ports to the switch managed by swconfig,
especally those with qca955x, line tplink archer c7 v2 and linksys ea4500 v3,
use vlan on different cpu port to separate networks by default. (e.g. eth1.1
for lan, eth0.2 for wan)
However, untagging to these vlans cpu ports, and limiting vlans in the switch
on these devices could effectively offload the expense to process vlan tag from
cpu to the switch, and increase the throughput of lan <-> wan ipoe routing.
Tested on my tplink tl-wdr4900 v2, where ucidef_add_switch "switch0"
"0u@eth1" "2:lan" "3:lan" "4:lan" "5:lan" "6u@eth0" "1:wan" finally generates
on /etc/config/network:
config device
option name 'br-lan'
option type 'bridge'
list ports 'eth1'
config interface 'lan'
option device 'br-lan'
option proto 'static'
list ipaddr '192.168.1.1/24'
option ip6assign '60'
config interface 'wan'
option device 'eth0'
option proto 'dhcp'
config interface 'wan6'
option device 'eth0'
option proto 'dhcpv6'
config switch
option name 'switch0'
option reset '1'
option enable_vlan '1'
config switch_vlan
option device 'switch0'
option vlan '1'
option ports '2 3 4 5 0'
config switch_vlan
option device 'switch0'
option vlan '2'
option ports '1 6'
and the throughput of lan <-> wan ipoe routing with software flow offload
increases from around
[850 Mbps](https://openwrt.org/toh/tp-link/archer-c5-c7-wdr7500#nat_performance)
to 900 Mbps.
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/19444
Signed-off-by: Robert Marko <robimarko@gmail.com>
These devices use the binding + eeprom-swap. Turns out the reason swap
is needed is because the binding wrongly swaps the data on big endian
hosts. NVMEM doesn't do this and thus just works.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22207
Signed-off-by: Robert Marko <robimarko@gmail.com>
A size of 600 is incomplete in that calibration data is not included,
resulting in low TX power.
Fixes: 64dae105 ("ramips: mt76x8: add support for Yuncore CPE200")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22459
Signed-off-by: Robert Marko <robimarko@gmail.com>
The dtsi used handles a bunch of non-DBDC platforms where the
assignments are correct. The 3040-a1 is different as there are 3 instead
of 2 wifi interfaces and WAN needs to be incremented by 1.
Remove userspace wifi assignmwent which was needed before per band nvmem
was supported.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21977
Signed-off-by: Robert Marko <robimarko@gmail.com>
While rebasing, a typo was made where the ';;' terminator was omitted in
the 02_network script. Add it to restore script functionality.
Fixes: e210d994fa ("airoha: an7581: add Nokia Valyrian support")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
- Update network port names based on the shell
- Fix boot log errors:
OF: /soc/pcie@11280000/pcie@0,0: Missing device_type
- Match vendor firmware Ethernet and wireless MAC addresses
LAN MAC 50:xx:xx:xx:xx:60
WAN MAC 50:xx:xx:xx:xx:61
2G MAC 50:xx:xx:xx:xx:63
5G MAC 50:xx:xx:xx:xx:65
Fixes: 7d79346581 ("mediatek: filogic: add support for Tenda BE12 Pro")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/22060
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Add support for Nokia Valyrian based on Airoha AN7581 SoC.
Device specification
--------------------
SoC Type: Airoha AN7581
RAM: 2x DDR4 Nanya NT5AD256M16E4-JR (1GB)
Flash: eMMC Macronix MX52LM08A11XVW (1GB)
Ethernet: 3x gigabit via AN7581, 1x 10g via AS21x1x, 1x SFP cage
Wi-Fi: MT7996 - BE19000
LEDs: 11 LED via 2x 74HC595 shift register
Button: Reset, WPS, WiFi
USB ports: 1x 2.0
Miscellaneous: 1x Power Monitor via RTQ6059, 2x FXS port
Device is unfused and is originally flashed with Airoha SDK bootloader
that require signed images.
Bootloader is username/password protected and use the leaked auth combo
that can be found online.
From the bootloadet instruction on how to flash custom bootloader are:
1. mmc erase 0 0x800
2. tftpboot 192.168.1.10:airoha/an7581/openwrt-airoha-an7581-nokia_valyrian-preloader.bin
3. mmc write $loadaddr 0x4 0xfc
4. tftpboot 192.168.1.10:airoha/an7581/openwrt-airoha-an7581-nokia_valyrian-bl31-uboot.fip
5. mmc write $loadaddr 0x100 0x700
It's also possible to use the Emergency Recovery procedure:
From powered OFF device:
1. Keep the reset button pressed (middle button)
2. Power on the device
3. Notice the "Press x" prompt
4. Press x
5. Notice the "C" char waiting for XMODEM load
6. Load the preloader binary with XMODEM protocol
7. Notice the "Press x to load BL31 + U-Boot FIP"
8. Press x
9. Notice the "C" char waiting for XMODEM load
10. Load the fip binary with XMODEM protocol
11. You are now in U-Boot loaded from serial
12. Follow normal procedure to flash bootloader
Due to BOOTROM limitation. the device can't have a standard GPT table
implementation. Because of this fixed-partitions are used to handle this.
U-Boot still doesn't have support for this (it's planned) and currently to flash
and load and image it's needed to write and read from static address in eMMC.
The GPT partition table follow Prpl guidelines with dual partition table with
kernel and rootfs split.
The address for kernel is 0xb00000 and the address for rootfs is 0x1b00000.
Link: https://github.com/openwrt/openwrt/pull/21761
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Set nand flash for KN-1910
Sysupgrade or any other method i tried (asu, owut) not working without it. Tested with a local build.
Signed-off-by: Esat Yiğithan GÖKTOPRAK <eygoktoprak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22311
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The bootcount init script is missing the executable bit (644 instead of 755),
causing the script to not be executable:
/etc/preinit: line 44: /etc/init.d/bootcount: Permission denied
Fixes: c3b8108a2b ("ramips: Add support for Xiaomi MiWiFi 3A")
Signed-off-by: Oliver Sedlbauer <os@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/22446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The MIPS code assigns the clock node based on the device tree node name.
This name was renamed with kernel 6.12.58 and v6.6.117. Adapt our out of
tree device tree files to this rename to fix loading the STP GPIO
driver.
Without this fix the driver fails like this:
```
[ 0.320000] gpio-stp-xway 1e100bb0.stp: Failed to get clock
[ 0.330000] gpio-stp-xway 1e100bb0.stp: probe with driver gpio-stp-xway failed with error -2
```
Link: https://git.kernel.org/linus/b0d04fe6a633ada2c7bc1b5ddd011cbd85961868
Fixes: https://github.com/openwrt/openwrt/issues/21697
Co-Authored-By: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22444
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Certain targets for an7581 and an7583 referred to kmod-pwm-airoha;
however in the target modules makefile the module is referred to
as kmod-pwm-an7581, causing buildbot to fail.
Change the name of kmod-pwm-an7581 to kmod-pwm-airoha to resolve this.
Signed-off-by: Kenneth Kasilag <kenneth@kasilag.me>
Link: https://github.com/openwrt/openwrt/pull/22445
Signed-off-by: Robert Marko <robimarko@gmail.com>
W1700K fan script is missing the #!/bin/sh /etc/rc.common shebang and
requires execution bits set. Also, set the fallback to hwmon 3 instead
of 5, since the new RTL PHY driver was not merged.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22391
Signed-off-by: Robert Marko <robimarko@gmail.com>
Note that for working G.hn support some packages need to be extracted from the Devolo firmware.
Signed-off-by: Julius Schwartzenberg <julius.schwartzenberg@eclipso.eu>
Link: https://github.com/openwrt/openwrt/pull/22123
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Developers no longer maintain this driver. And it has been replaced
by the new upstream implementation. It's time to say goodbye.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22214
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is the generic PWM framework driver for Mediatek SoC. Now
this module is ready for MT7628.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22214
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The upstream MediaTek PWM driver requires these clock sources to
work properly.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22214
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When running `make kernel_menuconfig`, CPU_BIG_ENDIAN is selected by
default, resulting in a non-bootable image. Add CPU_LITTLE_ENDIAN to
avoid that.
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22282
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The device dts files were moved to the dedicated directory in commit
a66e30631c ("qualcommax: move Device DTS to dedicated DTS directory"),
which resulted in a merge conflict.
Fixes: d755c49f7a ("qualcommax: ipq60xx: rename TP-Link EAP623-Outdoor HD v1 compatible")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22433
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for RTL9607C / RTL8198D thermal controller.
Based on the Realtek SDK code.
Signed-off-by: Rustam Adilov <adilov@tutamail.com>
Link: https://github.com/openwrt/openwrt/pull/22081
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The RTL8226 PHYs in Zyxel XGS1010-10 and XGS1210-10 rev A1 have swapped
MDI lanes. Specify this in the device tree, so the driver can configure
it. With this change, the PHYs no longer require initialization by the
bootloader.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/21261
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The PHY supports swapping the MDI pairs (ABCD->DCBA) to simplify board
layout. On devices making use of this, it needs to be configured in the
driver, otherwise the PHY won't work properly.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/21261
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The dsa irq handler works always in the same way for all SoCs.
- Read register ISR_PORT_LINK_STS_CHG to determine the ports that
triggered the irq.
- Write the read value back to the register to confirm the irq
- Read link status via MAC_LINK_STS
- Trigger dsa_port_phylink_mac_change() for each changed port
Currently each SoC has its own implementation. Drop that in
favour of a generic implementation that makes use of the existing
bit register read/write helpers.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22273
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This register will be needed to provide a generic irq handler. Add
it to the configuration structure of the driver.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22273
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some 10G optics showed random "module transmit fault indicated" due to I2C
read errors on ONTi ONT-S508CL-8S/XikeStor SKS8300-8X switches. The same
modules work with the original firmware and on other Linux based devices.
There seems to be some differences in how we talk to those modules using
I2C in OpenWRT. To fix this this patch adds support for 50kHz I2C speed on
SFPs and enables that for XikeStor/Onti devices. Since SFPs only transmit
very few bytes this should not have any real downsides.
This patch configures I2C to use 50kHz clock in the DTS for the affected
devices. For it to work it requires a change in the RTL9300 I2C driver.
This can be safely merged without the kernel change (but will not work
in that case as it will fall back to 100kHz).
Signed-off-by: Jan Kantert <jan-openwrt@kantert.net>
Link: https://github.com/openwrt/openwrt/pull/22210
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
No functional changes intended.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/22350
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The main difference between EAP610, 623, and 625 is the device name,
support string, and the BDF package. Move the others to a common
Device/tplink_eap6xx-common in order to highlight the common aspects.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18804
Signed-off-by: Robert Marko <robimarko@gmail.com>
The EAP625 and EAP623 are extremely similar. The only difference in
the vendor's device tree is that EAP625 also enables USB and UART2.
Use the eap6xx dtsi instead of writing out a full devicetree.
The EAP623 uses the same RTL8211F as the 625 and 610. Since this is
a gigabit PHY, it is okay to change the ess mac mode from SGMII_PLUS
to SGMII. This is now consistent across all three devices.
Move the 'realtek,clkout-disable' and 'realtek,aldps-enable' PHY
properties to the common dtsi, as they work well on all three devices.
Reflect the remaining differences in the eap625 dts.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18804
Signed-off-by: Robert Marko <robimarko@gmail.com>
As I was looking at the differences between EAP610, 623, and 625
Outdoor, I realized that the quick-start guide of all of the devices
mentions a yellow and green LED. Thus rename the "amber" led to
"yellow", and adjust its color ID accordingly.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18804
Signed-off-by: Robert Marko <robimarko@gmail.com>
Originally, the .compatible string for EAP623-Outdoor HD tried to
shorten the "-outdoor" to "od". However, this naming was inconsistent
with the existing "eap610-outdoor". As "od" is not a common shorthand,
spell out the complete word: "eap623-outdoor-hd-v1".
Fixes: 5dbf93c8c5 ("ipq60xx: add support for TP-Link EAP623-Outdoor HD v1")
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18804
Signed-off-by: Robert Marko <robimarko@gmail.com>
CI is currently failing due to these four patches.
Automatically refreshed with `make target/linux/refresh`.
Signed-off-by: Kenneth Kasilag <kenneth@kasilag.me>
Link: https://github.com/openwrt/openwrt/pull/22399
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Since the u-boot ethaddr variable is quoted, we cannot use it.
Use mac-base instead to specify in dts.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14182
Signed-off-by: Robert Marko <robimarko@gmail.com>
