mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2026-02-04 12:17:43 +01:00
00bb18b851
This pull request is based on - the discussions in https://forum.openwrt.org/t/adding-openwrt-support-for-linksys-mr6350 - https://github.com/openwrt/openwrt/pull/11405 which added support for similar devices. Device Specs: - IPQ4019 - Quad Core CPU - 256 MB RAM - 256 MB FLASH - 4 LAN ports, 1 WAN port - 2.4GHz (802.11n) and 5GHz (802.11c) wifi - 3 LEDs (Red, blue, green) which are routed to one indicator at the top of the case - 2 buttons (Reset, WPS) Disassembling the device: - There are 4 screws at the bottom of the device which must be removed - Two are under the fron rubber feets - Two are under the labels in the back (corner next to the rear rubber feets) Serial interface: - The serial interface is already populated on the device with a 6-pin header - Pin 1 is next to the heatsink - Pinout: 1: 3.3V, 2: TX, 3: RX, 4: unknown, 5: GND, 6: GND - Settings: 115200, 8N1 Migrating to OpenWrt requires multiple steps: - Load and boot the initramfs image - Adapt U-Boot settings to support bigger kernels - Flash the sysupgrade image Load and boot initramfs: - Connect serial interface - Set up a TFTP server on IP 192.168.1.254 - Copy openwrt-ipq40xx-generic-linksys_mr6350-initramfs-zImage.itb to TFTP server - Rename file to C0A80101.img - Boot up the device and stop in U-Boot - Run the following U-Boot commands after a link has been established: tftp bootm - Initramfs image is started now. Adapt U-Boot settings to support bigger kernels: - Run "fw_printenv" in the initramfs image after booting - There should be an entry kernsize=300000 which indicates the maximum size for the kernel is 3MB - Execute "fw_setenv kernsize 500000" to increase the max kernel size to 5MB - Check that the change are applied with "fw_printenv" Flash the sysupgrade image: - Default sysupgrade routine either with a initramfs image containing LuCI or via command line. Revert back to OEM firmware: - Only tested with FW_MR6350_1.1.3.210129_prod.img - Flash the OEM firmware via sysupgrade - Forced update is required Signed-off-by: Roland Reinl <reinlroland+github@gmail.com> Link: https://github.com/openwrt/openwrt/pull/17977 Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
|---|---|---|
| .. | ||
| apex | ||
| arm-trusted-firmware-bcm63xx | ||
| arm-trusted-firmware-mediatek | ||
| arm-trusted-firmware-mvebu | ||
| arm-trusted-firmware-rockchip | ||
| arm-trusted-firmware-stm32 | ||
| arm-trusted-firmware-sunxi | ||
| arm-trusted-firmware-tools | ||
| at91bootstrap | ||
| fconfig | ||
| grub2 | ||
| imx-bootlets | ||
| kexec-tools | ||
| kobs-ng | ||
| mt7623n-preloader | ||
| opensbi | ||
| optee-os-stm32 | ||
| rkbin | ||
| tfa-layerscape | ||
| uboot-airoha | ||
| uboot-armsr | ||
| uboot-at91 | ||
| uboot-ath79 | ||
| uboot-bcm53xx | ||
| uboot-bcm4908 | ||
| uboot-bmips | ||
| uboot-d1 | ||
| uboot-fritz4040 | ||
| uboot-imx | ||
| uboot-kirkwood | ||
| uboot-lantiq | ||
| uboot-layerscape | ||
| uboot-mediatek | ||
| uboot-mvebu | ||
| uboot-mxs | ||
| uboot-omap | ||
| uboot-rockchip | ||
| uboot-sifiveu | ||
| uboot-stm32 | ||
| uboot-sunxi | ||
| uboot-tegra | ||
| uboot-tools | ||
| uboot-zynq | ||