2a55846bf4
The GS1920-24HPv1 is a switch with 24 copper ports and 4 combo SFP/copper
ports and PoE on the first 24 ports.
Specifications:
---------------
* SoC: Realtek RTL8292M
* Flash: 16 MiB SPI flash
* RAM: 128 MiB
* Ethernet: 24x 10/100/1000 Mbps
* Buttons: 1x "Reset" button
* UART: 1x serial header, standard DCE pinout (Tx = 2, Rx = 3, Gnd = 5);
9600 baud, 8n1, +- 5.6V logic levels
* SFP: 4 combo copper/SFP ports
* PoE: 24x
* Fans: ADT7468 fan controller
Works:
------
- (24) RJ-45 ethernet ports
- Switch functions
- Buttons
- LEDs (partial support, the wrong LEDs light up)
- Manual fan control
Not yet enabled:
----------------
- PoE (requires patches to realtek-poe to support i2c)
- Combo ports (link is up, but no data is transferred)
Fans:
-----
After boot, the fans are running in full speed mode. You can interact
with the fan controller at /sys/class/hwmon/
Installation:
-------------
This device uses ZyNOS instead of Linux, this makes installation a bit
more cumbersome. Serial console is required!
1. Set the switch to boot from the first image. This step is crucial,
it will fail to boot if this is not set properly.
2. Connect to the switch using serial and interrupt the boot process
to enter debug/recovery mode.
3. Load the OpenWrt initramfs image via XMODEM. You need to obtain an
unlock code, based on your MAC address, first. See the excellent write
up at https://www.ixo.de/info/zyxel_uclinux/ for details. Replace
unlock_code in the commands below by the code obtained.
After running ATBA5, the terminal needs to be closed and re-opened
with 115200 baud. This speeds up the file transfer significantly!
The file length in bytes need to be given instead of file_length below.
You also need an XMODEM upload utility like "lrzsz-sx -X" to transfer
the file. Start the XMODEM upload after running the ATUPxxxx command:
> ATEN1,unlock_code
> ATBA5
> ATUP80100000,file_length
> ATGO80100000
4. Wait for OpenWrt to boot. Once this is done, transfer the loader binary
and the sysupgrade image to "/tmp" using scp.
5. Install OpenWrt permanently by running the following two commands on
the switch (over SSH):
> mtd write /tmp/loader.bin loader
> mtd write /tmp/sysupgrade.bin firmware
6. Reboot the switch and enjoy OpenWrt.
NB: You do not need to touch the loader binary unless it's recommended.
The loader is not part of a regular sysupgrade file and will be left
untouched. The boot loader only checks if the loader is valid to be
able to boot.
Recovery/ Return to stock:
--------------------------
Just spam the "u" key during (or "z" for 9600 baud) during memory testing
to trigger a recovery XMODEM upload at 115200 baud. A standard OEM upgrade
image works properly.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Link: https://github.com/openwrt/openwrt/pull/20439
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
||
|---|---|---|
| .devcontainer/ci-env | ||
| .github | ||
| .vscode | ||
| config | ||
| include | ||
| LICENSES | ||
| package | ||
| scripts | ||
| target | ||
| toolchain | ||
| tools | ||
| .gitattributes | ||
| .gitignore | ||
| BSDmakefile | ||
| Config.in | ||
| COPYING | ||
| feeds.conf.default | ||
| Makefile | ||
| README.md | ||
| rules.mk | ||
OpenWrt Project is a Linux operating system targeting embedded devices. Instead of trying to create a single, static firmware, OpenWrt provides a fully writable filesystem with package management. This frees you from the application selection and configuration provided by the vendor and allows you to customize the device through the use of packages to suit any application. For developers, OpenWrt is the framework to build an application without having to build a complete firmware around it; for users this means the ability for full customization, to use the device in ways never envisioned.
Sunshine!
Download
Built firmware images are available for many architectures and come with a package selection to be used as WiFi home router. To quickly find a factory image usable to migrate from a vendor stock firmware to OpenWrt, try the Firmware Selector.
If your device is supported, please follow the Info link to see install instructions or consult the support resources listed below.
An advanced user may require additional or specific package. (Toolchain, SDK, ...) For everything else than simple firmware download, try the wiki download page:
Development
To build your own firmware you need a GNU/Linux, BSD or macOS system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.
Requirements
You need the following tools to compile OpenWrt, the package names vary between distributions. A complete list with distribution specific packages is found in the Build System Setup documentation.
binutils bzip2 diff find flex gawk gcc-6+ getopt grep install libc-dev libz-dev
make4.1+ perl python3.7+ rsync subversion unzip which
Quickstart
-
Run
./scripts/feeds update -ato obtain all the latest package definitions defined in feeds.conf / feeds.conf.default -
Run
./scripts/feeds install -ato install symlinks for all obtained packages into package/feeds/ -
Run
make menuconfigto select your preferred configuration for the toolchain, target system & firmware packages. -
Run
maketo build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.
Related Repositories
The main repository uses multiple sub-repositories to manage packages of
different categories. All packages are installed via the OpenWrt package
manager called opkg. If you're looking to develop the web interface or port
packages to OpenWrt, please find the fitting repository below.
-
LuCI Web Interface: Modern and modular interface to control the device via a web browser.
-
OpenWrt Packages: Community repository of ported packages.
-
OpenWrt Routing: Packages specifically focused on (mesh) routing.
-
OpenWrt Video: Packages specifically focused on display servers and clients (Xorg and Wayland).
Support Information
For a list of supported devices see the OpenWrt Hardware Database
Documentation
Support Community
- Forum: For usage, projects, discussions and hardware advise.
- Support Chat: Channel
#openwrton oftc.net.
Developer Community
- Bug Reports: Report bugs in OpenWrt
- Dev Mailing List: Send patches
- Dev Chat: Channel
#openwrt-develon oftc.net.
License
OpenWrt is licensed under GPL-2.0