of_gpio.h is deprecated in upstream Linux and may be removed soon. Get
ahead of things and remove it. Most of these drivers already use the
gpiod API.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20076
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is a smart door lock device equipped with OpenWrt 14.07 OEM
modified version Qdwrt
The OEM has closed down, This commit is intended to maximize the
remaining value of these devices. It can flash OpenWrt to become
an AP
Specification:
- SoC: MediaTek MT7628NN
- Flash: 8 MB
- RAM: 64 MB
- Power: DC 5V - 25V
- Ethernet: 1 x RJ45 (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only
- On-Board LED:
Status 1: GPIO/43 active-low
Status 2: GPIO/44 active-low
Power: AlwaysOn
- Button:
WPS / RESET: GPIO/14 active-low
- Bluetooth: CC2541 via UART1 (ttyS1) and GPIO/26-29
- RFID: MF RC522 on I2C@28
- RTC: DS1339 on I2C@68
- Shell (via CON1 cable)
- LED (Swipe card area):
- Green GPIO/3 active-high
- Red GPIO/11 active-high
- Matrix keypad: (active-low)
GPIO/20 GPIO/21 GPIO/19 (Rows)
GPIO/24 1 2 3
GPIO/25 4 5 6
GPIO/22 7 8 9
GPIO/23 BACK 0 ENTER
(Cols)
- UART: 1 x UART on PCB - 57600 8N1
- GPIO Relay: GPIO/42 active-high
- GPIO Buzzer: GPIO/15 active-high
Warning:
The original firmware does not use the device tree.
This device tree is written based on the content of /sys/devices/platform
and has been tested
Note:
- On the device, matrix keypad rows actually are columns, and the columns actually are rows
- The key code of the CLEAR key of the matrix keypad is BACK in the original firmware.
Issue:
- No drivers in mainline kernel for RFID and Bluetooth.
Flash Instruction:
Using SSH/Telnet:
1. Connect the board to the computer via RJ45 Ethernet
2. Login 10.10.10.1 with root password "szqdingnet123" (SSH Port 22, Telnet Port 9900)
3. Download openwrt firmware on the computer.
4. Setup a http server on computer. And use wget download openwrt firmware from computer
5. Use command "mtd -r write openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin firmware"
to flash
Using U-Boot WebUI:
1. Configure PC with a static IP address 10.10.10.2/24.
2. Open http://10.10.10.1
3. Use "mkqdimg -B qc202 -f openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin" to
make image.
4. Upload factory.bin via U-Boot WebUI.
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-qianding-smart-locker-and-flash.html
Original U-Boot firmware image tools:
https://gitlab.com/CoiaPrant/mkqdimg
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17471
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These are already specified in DTS. Only thing missing is
label-mac-device.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19806
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Support in mt76 has existed for quite a while. Use it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19806
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
After trying to implement the gluon support for this device I ended up in a boot loop due to the usable amount of flash left. With this patch layout it uses the unused and empty flash space in the original partiton layout.
The version 3 of this device the RE365 share the same approach to have more usable space.
Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
Link: https://github.com/openwrt/openwrt/pull/18639
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Use Unix LF style instead of Windows CRLF style.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19963
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move append-teltonika-metadata to image-commands.mk and unify over different targets.
This method can be used to create valid "factory" images for most of Teltonika devices.
Signed-off-by: Simonas Tamošaitis <simsasss@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19401
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Support in mt76 has existed for quite a while. Use it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19799
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CREALITY BOX WB01 is small footprint router based on MediaTek MT7688,
is a device intended to interface Creality brand 3D printers to a cloud service.
Specifications:
- SoC: MediaTek MT7688AN @ 580MHz
- RAM: DDR2 128M (Winbond W971GG6SB-25)
- Flash: BoyaMicro BY25Q128AS (16 MiB, SPI NOR) handled by BoHong bh25q128as driver
- WiFi: 2.4GHz 1T1R internal panel antenna
- Ethernet: 1x LAN (10/100)
- USB: 2x USB2.0 port (Genesys Logic GL850G 2 port USB 2.0 hub)
- UART: 3.3V, TX, RX, GND / 56700 8N1 / only pads on PCB
- microSD SD-XC Class 10 slot
- micro USB input (for power only)
- reset button
- FCC ID: 2AXH6CREALITY-BOX
MAC addresses as verified by OEM firmware:
vendor OpenWrt source
LAN eth0 factory 0x2e
2.4GHz phy0-ap0 factory 0x04 (label)
LEDs
color vendor OpenWRT configurable
red SD card activity - yes
green Cloud connectivity status yes
blue LAN activity eth0 yes
yellow WIFI activity phy0tpt yes
Return to OEM & debrick
- download "cxsw_update.tar.bz2" from manufacturer site
- extract archive to FAT32 USB stick root
- put USB stick in USB2 port
- press & hold reset button
- power on device while holding reset
- wait approx 10 sec
- release reset button
Installation with SD Card
- power on device
- wait for device to finish starting
- copy "openwrt-ramips-mt76x8-creality_wb-01-squashfs-cxsw_update.tar.bz2"
to root of FAT32 SD card
- rename openwrt-ramips-mt76x8-creality_wb-01-squashfs-cxsw_update.tar.bz2
to "cxsw_update.tar.bz2"
- put SD card in device
- device will install OpenWRT on internal flash
Installation via telnet:
- extract the "factory.bin" and "install.sh" from newly created
openwrt-ramips-mt76x8-creality_wb-01-squashfs-cxsw_update.tar.bz2
to FAT32 USB stick root
- telnet to 10.10.10.254, user: root, password: cxswprin
- plug the USB in USB1 port
- cd /media/usbdisk/
- sh install.sh
- device will write "factory.bin" to internal flash
Co-authored-by: George Brooke <figgyc@figgyc.uk>
Co-authored-by: Peca Nesovanovic <peca.nesovanovic@sattrakt.com>
Co-authored-by: shivajiva101 <github.com/shivajiva101>
Co-authored-by: Axel Sepulveda <ansepulveda@uc.cl>
Signed-off-by: Axel Sepulveda <ansepulveda@uc.cl>
Link: https://github.com/openwrt/openwrt/pull/19686
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This makes 5ghz WiFi work out of the box on these devices, eliminating
the need to flash a magic blob to the radio partition.
This was found by user BulldozerBSG on the OpenWRT Forums:
https://forum.openwrt.org/t/tp-link-archer-mr600-exploration/65489/20
All credit belongs to them. I can confirm the correctness of the
findings. At least one other user (Iggy87100) confirmed them too.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19790
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Support in mt76 has existed for quite a while. Use it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19771
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an industrial 4G router equipped with OpenWrt SNAPSHOT OEM
customized version
WARNING: The original firmware device tree is modified from evb
boards, and the device tree name is evb board. This submitted device
tree is a modified version, which deletes the non-this-device parts
and adds GPIO watchdog.
Specification:
- SoC: MediaTek MT7628NN
- Flash: 16 MB
- RAM: 128 MB
- Power: DC 5V-36V 1.5A
- Ethernet: 1x WAN [slot not install], 1x LAN (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only [antenna not install]
- LED:
System/Power (RUN): GPIO/37 active-low
Modem: GPIO/3 active-low
RF (Modem Signal): GPIO/2 active-low
- Button:
WPS / RESET: GPIO/11 active-low
- UART: 1x UART on PCB - 115200 8N1
- Serial / COM: 1X RS232/RS485 on board (GPIO/6 hi:RS485 lo:RS232)
- GPIO Watchdog: GPIO/0 mode=toggle timeout=1s
- Modem: 1x Built-in modem on board (Power: GPIO/4 active-high)
- PCIe: 1x miniPCIe for modem [slot not install]
- SIM Slots: 1x SIM Slots
Issue:
- Factory partition not store mac address on original firmware
Flash instruction:
Using SSH/Telnet:
1. Connect the board to the computer via RJ45 Ethernet
2. Login 192.168.8.1 with root password "superzxmn" (SSH Port 22, Telnet Port 5188)
3. Download openwrt firmware on the computer.
4. Use scp or sftp put firmware to board /tmp
5. Use command "mtd -r write openwrt-ramips-mt76x8-hongdian_h7920-v40-squashfs-sysupgrade.bin firmware"
to flash
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-hongdian-h7920-v40-and-flash.html
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17726
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for a dual-band AC1200 wall plug
manufactured by Shenzhen Century Xinyang Tech Co., Ltd.
SoC: Mediatek MT7628AN (MIPS 24KEc single core, 580 MHz)
RAM: 128 MiB DDR2 (Hynix HY5PS1G1631C)
ROM: 8 MiB SPI NOR (Zbit ZB25VQ64ASIG)
Wired: one FE RJ45 port (+ an unpopulated footprint for a 2nd)
WiFi: Mediatek MT7612E
Ant.: four 2 dBi external antennas (two 2.4GHz, two 5 GHz)
LEDs: - Power (green, always on)
- 2.4G (green, controlled by MT7628)
- 5G (green, controlled by MT7612)
- Extender (green, GPIO 37, used as status LED)
- LAN (green/yellow, controlled by RT3050 ESW)
Buttons: WPS and reset (both connected to GPIO 38)
Power: 5V 2-pin JST-XH on main PCB
110/220V AC to 5V 1.5A DC on auxiliary PCB
UART: 57600 8n1 3.3v, holes available on the PCB as J5
pinout is (Gnd) (Tx) (Rx)
MAC: 1C:BF:CE:xx:xx:xx (2.4 GHz, label)
1C:BF:CE:xx:xx:xx + 1 (LAN)
1C:BF:CE:xx:xx:xx + 2 (WAN, not in use)
1C:BF:CE:xx:xx:xx + 3 (5 GHz)
Original firmware is Chaos Calmer 15.05.01 (kernel 3.10.108)
with a few custom packages and a non-LuCI web interface.
Telnet is enabled, requiring an unknown root password [1].
Root password is also needed to access the router via UART console,
but passwordless telnet can be enabled via a trivial web exploit [2]
and then the root password can be removed by editing `/etc/shadow`.
Installation: Upload `sysupgrade` binary via web interface at
`http://192.168.188.1/settings.shtml`. Alternatively, remove
root password and use u-boot menu to flash image via TFTP.
Notes:
- Device model in Chaos Calmer is "mtk-apsoc-demo".
- It is sold under several brands, e.g., Fenvi and Linkavenir.
It is available in two colors: white and black.
- PCB is marked "WD206AD v1.0".
- Instead of a standard ethernet transformer, the PCB has a few tiny
SMD coils.
- The housing is identical to the one used by a 2020 model,
WD-R1203U, which is RTL8812-based. The older model has an FCC
listing with external and internal images: ZNPWD-R1203U.
The FCC listing contains a letter [3] claiming WD-R1203U and
WD-R1208U are internally identical, but evidently they are not.
[1] root:$1$7rmMiPJj$91iv9LWhfkZE/t7aCBdo.0:18388:0:99999:7:::
This is the same hash as in Wodesys WD-R1802U.
There are other root password hashes in `/etc/shadow_sf` and
`/etc/shadow_yn`.
[2] curl -X POST http://192.168.188.1/cgi-bin/adm.cgi \
-d page=Lang -d langType="en;killall telnetd;telnetd -l /bin/sh"
[3] https://fcc.report/FCC-ID/ZNPWD-R1203U/4767033
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19535
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SIM SIMAX1800U has the similar hardware design as the SIMAX1800T. The
only difference is the Ethernet portmap.
Specification
-------------
- SoC : Mediatek MT7621
- RAM : 256 MiB DDR3
- Flash : 128 MiB NAND Flash
- WLAN : Mediatek MT7905 DBDC
- 2.4 GHz : 2x2 MIMO WiFi6
- 5 GHz : 2x2 MIMO WiFi6
- Ethernet : MT7621 built-in 10/100/1000 Mbps 1x WAN; 3x LAN
- UART : 3.3V, 115200n8
- Buttons : 1x RESET; 1x WPS/MESH
- LEDs : 1x Multi-Color(Blue;Green;Red)
- Power : DC 12V1A
- CMIIT ID : 2022AP7163
- TFTP IP :
- server : 192.168.1.254
- router : 192.168.1.28
TFTP Installation(recommend)
------------
1. Set local tftp server IP "192.168.1.254" and NetMask "255.255.255.0".
2. Rename initramfs-kernel.bin to "factory.bin" and put it in the root
directory of the tftp server. tftpd64 is a good choice for Windows.
3. Remove all Ethernet cables and WiFi connections from the PC, except
for the one connected to the SIMAX1800U. Start the TFTP server, plug
in the power adapter and wait for the OpenWrt system to boot.
4. Backup "firmware" partition and rename it to "firmware.bin". We need
it to back to the stock firmware.
5. Use "fw_printenv" command to list envs. If "firmware_select=2" is
observed then set u-boot env variable via command:
`fw_setenv firmware_select 1`
6. Apply sysupgrade.bin in OpenWrt LuCI.
Web UI Installation
------------
1. Apply update by uploading initramfs-factory.bin to the web UI.
2. Use "fw_printenv" command to list envs. If "firmware_select=2" is
observed then set u-boot env variable via command:
`fw_setenv firmware_select 1`
3. Apply squashfs-sysupgrade.bin in OpenWrt LuCI.
Return to Stock Firmware
----------------------------
Restore the backup firmware partition in the installation step 4.
MAC addresses
-------------
+---------+-------------------+
| | MAC example |
+---------+-------------------+
| LABEL | 98:xx:xx:xx:xx:b2 |
| LAN | 98:xx:xx:xx:xx:b5 |
| WAN | 98:xx:xx:xx:xx:b2 |
| WLAN2G | 98:xx:xx:xx:xx:b4 |
| WLAN5G | 9a:xx:xx:xx:xx:b4 |
+---------+-------------------+
Tips:
-----------
User can use `TFTP Installation` method to recover a brick device.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19455
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix bootloop on TP-Link EAP615-Wall v1 by reducing LZMA dictionary
size. Before this patch and after an upgrade to kernel 6.12 this
device couldn't boot a kernel because of an error: "lzma compressed:
uncompress error 1".
I have chosen -d22 as dictionary size as suggested by @namiltd.
The usual sizes for problematic devices are -d16, -d20, -d22. I
have confirmed with my tests that this device can boot with a value
up to -d27, but there is no size benefit from values above -d21,
therefore -d22 is good enough.
See also: https://github.com/openwrt/openwrt/issues/19403
Signed-off-by: Marcin FM <marcin@ipv8.pl>
Link: https://github.com/openwrt/openwrt/pull/19433
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Wavlink Aerial HD3 (WL-WN570HA2) is an AC1200 dual-band outdoor
access point. It supports 802.3AT/AF PoE and is IP67 waterproof.
It is based on the MediaTek MT7628DAN SoC and MT7613BEN WiFi 5 chip.
This model uses the 100Mbit LAN and 2.4Ghz WiFi elements of the
MT7628 and the 5Ghz WiFi of the MT7613.
Specification:
- SoC: MediaTek MT7628DAN (1C/1T) @ 580MHz
- RAM: 64MB DDR2 (integrated in SoC)
- FLASH: 16MB SPI NOR (Fudan FM25Q128A)
- Ethernet: 1x 10/100Mbps
- WiFi: 2.4/5 GHz 2T2R
- 2.4GHz MediaTek MT7628DAN bgn
- 5GHz MediaTek MT7613BEN nac
- Antennas: 2x detachable, dual-band 7dBi with RP-SMA connectors.
- USB: none
- BTN: Reset
- LED: 6 total: power; WAN/LAN; WiFi; WiFi low; WiFi med; Wifi high
- UART: surface-mount on PCB. Pins are marked via silkscreen.
pin1 (square pad, towards Ethernet)=Vcc, pin2=RX,
pin3=TX, pin4=GND. Settings: 57600/8N1.
NOTE: The TX & RX silkscreens were reversed on my test unit.
Installation:
1) This device requires a HTTP recovery procedure to do an initial load
of OpenWRT. You will need:
a. A web browser (private window recommended)
b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1
c. Connect a cable between the computer and the Wavlink's PoE injector.
2) Put the Wavlink in HTTP recovery mode.
a. Do this by pressing and holding the reset button on the bottom while
powering the unit on.
b. As soon as all 6 LEDs light up blue (roughly 2-3 seconds), release
the button.
c. The LEDs should all remain lit, indicating it's in HTTP recovery.
3) Point the browser at http://192.168.1.1/index.html
4) Click "Choose File" and select the OpenWRT sysupgrade image.
5) Click the "Update Firmware" button and wait while the unit flashes
the image and reboots.
6) When the system comes back up fully, only the power LED will be lit.
Wait an extra minute then you should be able to reach OpenWRT on
http://192.168.1.1
5) Log into LuCI as root; there is no password.
Revert to the OEM Firmware:
--------------------------
* U-boot HTTP:
Follow the HTTP recovery steps, and use a firmware image downloaded
from Wavlink.
Signed-off-by: Jonathan Sturges <jsturges@redhat.com>
Link: https://github.com/openwrt/openwrt/pull/18856
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This device is similar to the TP-Link EX220 v1.
The differences are the number of ports (3 LANs
and 1 WAN) and the number of LEDs (1 LED RGB)
Hardware
--------
CPU: MediaTek MT7621 DAT
RAM: 128MB DDR3 (integrated)
FLASH: 16MB SPI-NOR
WiFi: MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax
SERIAL: 115200 8N1
LED - (TX - RX - GND - 3V3 ) - ETH ports
Installation
------------
Flashing is only possible via a serial connection using the sysupgrade
image; the factory image must be signed. You can flash the sysupgrade
image directly through the U-Boot console, or preferably, by booting the
initramfs image and flashing with the sysupgrade command. Follow these
steps for sysupgrade flashing:
1. Establish a UART serial connection.
2. Set up a TFTP server at 192.168.0.2 and copy the initramfs image
there.
3. Power on the device and press any key to interrupt normal boot.
4. Load the initramfs image using tftpboot.
5. Boot with bootm.
6. If you haven't done so already, back up all stock mtd partitions.
7. Copy the sysupgrade image to the router.
8. Flash OpenWrt through either LuCI or the sysupgrade command. Remember
not to attempt saving settings.
Revert to stock firmware
------------------------
Flash stock firmware via OEM web-recovery mode. If you don't have access
to the stock firmware image, you will need to restore the firmware
partition backed up earlier.
Web-Recovery
------------
The router supports an HTTP recovery mode:
1. Turn off the router.
2. Press the reset button and power on the device.
3. When the LED start flashing, release reset and quickly press it
again.
The interface is reachable at 192.168.0.1 and supports installation of
the OEM factory image. Note that flashing OpenWrt this way is not
possible, as mentioned above.
Signed-off-by: Gustavo Curi <gpcuri@land.ufrj.br>
Link: https://github.com/openwrt/openwrt/pull/19104
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Replace .remove_new with .remove for compatibility with future kernel versions.
Dropping compatibility with older kernels.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/19320
Signed-off-by: Nick Hainke <vincent@systemli.org>
Drop configs and patches for Linux 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/19320
Signed-off-by: Nick Hainke <vincent@systemli.org>
Switch to Linux kernel version 6.12.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/19320
Signed-off-by: Nick Hainke <vincent@systemli.org>
Replaced all mt76@ with wifi@ per upstream requirement for all wifi
nodes.
Added missing compatible string where appropriate as stated by mt76.yaml
upstream.
Also updated reg value to be consistent everywhere.
Replace all pci14c3 entries to use mediatek,mt76.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19067
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specification:
SoC: MediaTek MT7628NN
RAM: 128 MB, EtronTech EM68C16CWQG-25H (DDR2)
Flash: 32MB, Winbond 25Q256JVFQ (Dual Boot, SPI)
Switch: MediaTek MT7628AN, 4 ports 100 Mbps
WiFi: MediaTek MT7603 2T2R/2.4GHz 802.11n
GPIO: 3 buttons (Wi-Fi, Reset, FN), 3 LEDs (Power, Internet, Wi-Fi), 1 port USB 2.0
Disassembly:
At the bottom, under the LEDs, there are 2 screws hidden by rubber feet. After removing the screws, pry the gray plastic part around (it is secured with latches) and remove it.
Serial Interface:
The serial interface can be connected to the 5 pin dots located on the right between the operating mode switch and the antenna.
Pins (from antenna to operating mode switch):
VCC
TX
RX
NC
GND
Settings: 115200, 8N1
Flashing via OEM recovery software:
1. Download the OEM recovery software from the manufacturer's website
2. Download the firmware image (for OpenWRT it is *-squashfs-factory.bin), rename it to KN-1212_recovery.bin
3. Replace the file in the fw folder OEM recovery software with the file from step 2.
4. Run the OEM recovery software and follow the instructions.
Flashing via TFTP:
1. Connect your PC and router to port 1-3, configure PC interface using IP 192.168.1.2, mask 255.255.255.252
2. Serve the firmware image (for OpenWRT it is *-squashfs-factory.bin) renamed to KN-1212_recovery.bin via TFTP
3. Power up the router while pressing Reset button on the back
4. Release Restart button when Power LED starts blinking
To revert back to OEM firmware:
The return to the OEM firmware is carried out by using the methods described above with the help of the appropriate firmware image.
When using OEM bootloader, the firmware image size cannot exceed the size of one OEM «Firmware_x» partition or Kernel + rootFS size.
Signed-off-by: Anton Yu. Ivanusev <ivanusevanton@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/19157
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
JDCloud RE-SP-01B is a dual-band WiFi 5 router based on the MT7621AT.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 512MB DDR3
- Flash: 32MB SPI NOR
- WiFi: MediaTek MT7603EN (2.4GHz), MediaTek MT7615N (5GHz)
- Ethernet: 1x WAN, 2x LAN (Gigabit Ethernet)
- LEDs: red, blue, green (GPIO controlled)
- Button: Reset (GPIO controlled)
- eMMC: Single onboard (32GB/64GB/128GB)
- USB: 1x USB 2.0 port
MAC Address Structure:
The MAC addresses share the structure DC:D8:7C:XX:XX:XX, where:
- WAN, LAN, and 2.4GHz WiFi: same as the label MAC address.
- 5GHz WiFi: label MAC address + 0x800000.
The manufacturer writes the label MAC address at different
offsets depending on the storage version of the device:
e.g.
128GB version: &config + 0x442a
64GB version: &config + 0x4429
So `get_mac_ascii()` is used here to search for the
base label MAC address of the device.
Ref:
https://github.com/openwrt/openwrt/pull/17409#discussion_r1899674262https://github.com/immortalwrt/immortalwrt/commit/c0c480d
Flash Instruction:
A 3rd party bootloader is required to boot the image. You can
use a SOP16 test clip to burn the image/bootloader to the flash.
The official bootloader does provide a web recovery interface
which only accepts an official image. To access it, you will
need to hold the reset button and power on the device, set your
IP address to 192.168.68.2 and visit http://192.168.68.1.
Co-authored-by: Chukun Pan <amadeus@jmu.edu.cn>
Signed-off-by: Yijie Jin <jinyijie@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The High-Speed SD mode stability issue should have been fixed.
Increase the MMC max-frequency to improve the IO speed. We can
still use the sysfs to limit the clock frequency, e.g.
root@OpenWrt:~# echo 25000000 > /sys/kernel/debug/mmc0/clock
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18896
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This new feature has some improvements for random RW performance.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18896
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The MT7628 programing guide shows that the correct DTOC unit is
1048576 clocks instead of 65536 clocks. This value is also used
by linux upstream mtk-sd driver. Correct the DTOC register and
also round up its value.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18896
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
SoC: MediaTek MT7628NN
RAM: 128 MB, EtronTech EM68C16CWQG-25H (DDR2)
Flash: 32MB, Winbond 25Q256JVFQ (Dual Boot, SPI)
Switch: MediaTek MT7628AN, 4 ports 100 Mbps
WiFi: MediaTek MT7603 2T2R/2.4GHz 802.11n
GPIO: 2 buttons (Wi-Fi, Reset), 3 LEDs (Power, Internet, Wi-Fi), 1 mode switch
Disassembly:
At the bottom, under the LEDs, there are 2 screws hidden by rubber feet. After removing the screws, pry the gray plastic part around (it is secured with latches) and remove it.
Serial Interface:
The serial interface can be connected to the 5 pin dots located on the right between the operating mode switch and the antenna.
Pins (from antenna to operating mode switch):
VCC
TX
RX
NC
GND
Settings: 115200, 8N1
Flashing via OEM recovery software:
1. Download the OEM recovery software from the manufacturer's website
2. Download the firmware image (for OpenWRT it is *-squashfs-factory.bin), rename it to KN-1112_recovery.bin
3. Replace the file in the fw folder OEM recovery software with the file from step 2.
4. Run the OEM recovery software and follow the instructions.
Flashing via TFTP:
1. Connect your PC and router to port 1-3, configure PC interface using IP 192.168.1.2, mask 255.255.255.252
2. Serve the firmware image (for OpenWRT it is *-squashfs-factory.bin) renamed to KN-1112_recovery.bin via TFTP
3. Power up the router while pressing Reset button on the back
4. Release Restart button when Power LED starts blinking
To revert back to OEM firmware:
The return to the OEM firmware is carried out by using the methods described above with the help of the appropriate firmware image.
When using OEM bootloader, the firmware image size cannot exceed the size of one OEM «Firmware_x» partition or Kernel + rootFS size.
Signed-off-by: Anton Yu. Ivanusev <ivanusevanton@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/19091
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Multiple users have reported a regression [1] in OpenWRT 24.10 with the
ramips/mt7621 target, which has the MT7530 PHYs: the Ethernet link is
periodically going down for a brief period of time:
mt7530-mdio mdio-bus:1f lan1: Link is Down
br-lan: port 1(lan1) entered disabled state
mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
The symptoms stop after disabling EEE and it was reported by Mediatek in
2021 that EEE is unstable for the MT7530 PHYs [2]:
> EEE of the 10-year-old MT7530 internal gephy has many IOT problems, so
> it is recommended to disable its EEE.
EEE is enabled by default for these devices in OpenWRT 24.10 whereas in the
previous version (OpenWRT 23.05, Linux 5.15) it was not. It was determined
that in Linux 6.6, the PHY driver tries to disable EEE in
mtk_gephy_config_init() in drivers/net/phy/mediatek-ge.c, but this is later
overridden by a subsequent execution of the genphy_c45_write_eee_adv()
function, which enables every EEE mode supported.
The best way forward for now seems to be to mark EEE as broken directly in
the devicetree, which affects the genphy_c45_write_eee_adv() function.
There are some devices, like GnuBee GB-PC2, that define additional PHYs,
for example ethernet-phy@5 or ethernet-phy@7. As reported by Chester A.
Unal, these are not MT7530 PHYs and they are not affected.
This would need to be cherrypicked for the OpenWRT 24.10 branch.
[1] https://github.com/openwrt/openwrt/issues/17351
[2] https://lore.kernel.org/all/0adde34f936a2dafca40b06b408d82afe0852327.camel@mediatek.com/
Tested-by: Darren Tucker
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Closes: https://github.com/openwrt/openwrt/issues/17351
Link: https://github.com/openwrt/openwrt/pull/18585
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Missing headers causes an error on kernel 6.12:
arch/mips/ralink/irq.c:86:5: error: no previous prototype for 'get_c0_perfcount_int' [-Werror=missing-prototypes]
86 | int get_c0_perfcount_int(void)
| ^~~~~~~~~~~~~~~~~~~~
arch/mips/ralink/irq.c:92:14: error: no previous prototype for 'get_c0_compare_int' [-Werror=missing-prototypes]
92 | unsigned int get_c0_compare_int(void)
| ^~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18654
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Replace macros with empty body with 'do {} while (0)'.
Remove unnecessary semicolons.
Fixes:
drivers/mmc/host/mtk-mmc/sd.c: In function 'msdc_irq':
drivers/mmc/host/mtk-mmc/sd.c:1969:87: error: suggest braces around empty body in an 'else' statement [-Werror=empty-body]
1969 | IRQ_MSG("XXX CMD<%d> MSDC_INT_RSPCRCERR", cmd->opcode);
| ^
drivers/mmc/host/mtk-mmc/sd.c:1975:84: error: suggest braces around empty body in an 'else' statement [-Werror=empty-body]
1975 | IRQ_MSG("XXX CMD<%d> MSDC_INT_CMDTMO", cmd->opcode);
| ^
cc1: all warnings being treated as errors
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18654
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add uboot-envtools (removing -uboot-envtools) to devices which were
missed in the commit 79bd017 ("ramips: mt7621: add uboot-envtools to
all devices")
- Mi Router 3G
- Mi Router AC2100
While at here remove two redundant entries from devices which were added
just after the referenced commit 79bd017 and did not account for the
new DEFAULT_PACKAGES member:
- SNR-CPE-ME1
- SNR-CPE-ME2-SFP
Fixes: 79bd017 ("ramips: mt7621: add uboot-envtools to all devices")
Fixes: https://github.com/openwrt/openwrt/issues/18960
Signed-off-by: Mario Andrés Pérez <mapb_@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19012
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
