Use upstreamed patch for adding the tsens node.
Temperature sensors are enabled by default, therefore remove explicit
enablement in board files.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19890
Signed-off-by: Robert Marko <robimarko@gmail.com>
Converts the KS8995 "phy" driver to a proper DSA switch.
Currently the upstream only supports the "none" tag
but this is a good improvement already.
Make the old module depend on kernel 6.6 and the new
one depend on !6.6.
The Realtek RTL8261n patch needs to be refreshed
because of textual dependencies.
Realtek RTL838x DSA and phy patches also have textual
dependencies and need to be refreshed.
The Mediatek in-flight DSA patch and related patches
also need to be rebased and refreshed.
Link: https://github.com/openwrt/openwrt/pull/19970
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change fixes the eeprom load failure while on boot
Signed-off-by: Rhnn Hur <hurrhnn@icmp.kr>
Link: https://github.com/openwrt/openwrt/pull/20044
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This addresses #9113 by adding up to 1MB padding after writing the
rootfs image. On boot mount_root will probe for existing filesystems
after the rootfs image data. Without overwriting the initial free
space left on the rootfs partition, OpenWrt might incorrectly detect
an exising filesystem and fails to mount it, resulting in a bricked
device as the overlayfs will not be mountend and settings will not be
available.
Fixes#9113.
Signed-off-by: Orne Brocaar <info@brocaar.com>
Link: https://github.com/openwrt/openwrt/pull/19997
Signed-off-by: Robert Marko <robimarko@gmail.com>
During SerDes rework the helper functions were temporarily
renamed to ..._new(). Fix the leftovers by
- giving the functions a new rtsds_ prefix nad
- dropping the _new appendix.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20034
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specification
-------------
- SoC : MediaTek MT7986AV quad-core ARM Cortex-A53 2GHz
- RAM : DDR4 512Mbytes, Nanya Technology NT5AD256M16E4
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976DAN, MediaTek MT7916AN, MediaTek MT7976AN
- 2.4GHz : b/g/n/ax, Multi User MIMO
- 5GHz : a/n/ac/ax, Multi User MIMO
- 6GHz : ax, Multi User MIMO
- Ethernet : 10/100/1000 Mbps x4, LAN (MediaTek MT7531AE)
10/100/1000/2500 Mbps x1, WAN (MaxLinear GPY211C0VC)
- UART : 1x4 pin header on PCB
- [J1] 3.3V, TX, RX, GND (115200, 8N1)
- Buttons : WPS, Reset
- Switches : Rfkill Slide Switch
- USB : 1x USB 3.0 (MediaTek MT7986AV peripheral)
- FAN : 1x Fan (off - slow - fast)
- LEDs : 1x Power (Blue)
1x CPU (Blue)
1x Wi-Fi 6GHz (Blue)
1x Wi-Fi 5GHz (Blue)
1x Wi-Fi 2.4GHz (Blue)
4x LAN activity (Blue)
1x WAN activity (Blue)
1x USB 3.0 (Blue)
- Power : 12VDC, 3.5A (Center positive polarity)
MAC address
-----------
+-----------+-------------------+------------------------+
| Interface | MAC | Algorithm |
+-----------+-------------------+------------------------+
| WLAN 2.4G | 58:86:94:xx:xx:xx | label1 |
| WLAN 5G | 5A:86:94:xx:xx:xx | label2 with LA Bit set |
| WLAN 6G | 5A:86:94:xx:xx:xx | label1 with LA Bit set |
| WAN | 58:86:94:xx:xx:xx | label1 + 1 |
| LAN | 58:86:94:xx:xx:xx | label1 + 3 |
+-----------+-------------------+------------------------+
The WLAN 2.4G MAC address (label1) was found in 'Factory' partition, 0xA0004
The WLAN 5G MAC address (label2) was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software (ipTIME Firmware Wizard (11ac))
from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router (keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router (LAN port) to the PC
6. Run the OEM recovery software and follow the instructions
7. Select the *squashfs-factory.bin file during the router recovery process
8. Wait for the router to boot from *squashfs-factory.bin
Note: The router will automatically reboot if no file is uploaded within
55 seconds.
Fan Control
------------
The fan speed is controlled by writing a value from 0 to 2 to the
`fan1_target` file.
```
cd /sys/devices/platform/gpio-fan/hwmon/hwmon2
echo '0' > fan1_target // off
echo '1' > fan1_target // slow
echo '2' > fan1_target // fast
```
Limitation: Enabling Wi-Fi 6E
----------
Wi-Fi 6E (6GHz) does not work out of the box on LuCI.
After installation, you need to configure a few settings in the `radio1`
and `default_radio1` sections of the `/etc/config/wireless`.
Once you have made these changes, you can enable and use Wi-Fi 6E.
In the `radio1` section, you need to add three common options:
- band: must be set to `6g`
- country: a valid country code for the 6GHz band
- channel: a preferrend scanning channel (PSC) for 6GHz
In the `default_radio1` section, you need to add the SSID and key:
- ssid: The public name of your Wi-Fi network
- key: The Wi-Fi password
- encryption: must be set to either `sae` for WPA3 or `owe` for OWE
(open network)
Example:
```
config wifi-device 'radio1'
...
option band '6g'
option country 'KR'
option channel '37'
...
config wifi-iface 'default_radio1'
...
option ssid 'my_wifi_6e_name'
option key 'my_strong_password1234'
option encryption 'sae'
...
```
Note: A list of all the 6GHz PSC channels:
```
5, 21, 37, 53, 69, 85, 101, 117, 133, 149, 165, 181, 197, 213, and 229
```
Limitation: Maximum Transmit Power
----------
The maximum transmit power is currently broken. In the drop-down menu,
you can only choose between "driver default" and "255 dBm (2147493647
mW)". There is currently no workaround for the issue. Please leave the
maximum transmit power set to "driver default".
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19763
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add driver for hardware random number generator found in MT7981, MT7988
and MT7987. This gives us a fast source of high-quality random numbers
on those platforms.
root@OpenWrt:~# cat /dev/hwrng | rngtest -c 10000
rngtest 6.17
Copyright (c) 2004 by Henrique de Moraes Holschuh
This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
rngtest: starting FIPS tests...
rngtest: bits received from input: 200000032
rngtest: FIPS 140-2 successes: 9988
rngtest: FIPS 140-2 failures: 12
rngtest: FIPS 140-2(2001-10-10) Monobit: 2
rngtest: FIPS 140-2(2001-10-10) Poker: 0
rngtest: FIPS 140-2(2001-10-10) Runs: 4
rngtest: FIPS 140-2(2001-10-10) Long run: 6
rngtest: FIPS 140-2(2001-10-10) Continuous run: 0
rngtest: input channel speed: (min=616.108; avg=11979.007; max=19531250.000)Kibits/s
rngtest: FIPS tests speed: (min=1.859; avg=82.116; max=83.656)Mibits/s
rngtest: Program run time: 18629928 microseconds
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The kernel config accidentally contains CONFIG_UBIFS_FS_AUTHENTICATION
which select a number of other unnecessary components, remove them.
The target has at least two subtargets, only one is currently
implemented. Move the Device builds into a file for this subtarget.
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://github.com/openwrt/openwrt/pull/20027
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that HSGMII is not used any longer drop the patch
the invents this mode.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20002
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The only consumers of the Realtek HSGMII (2.5G SGMII) mode were
the RTL8226/RTL8221B PHYs. These have been converted to dynamic
SGMII/2500base-x mode switching. Drop the leftovers of the mode
implementation.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20002
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The mdio controller got its own dts node with a dedicated bus node.
Until now it still searches the phy nodes in the ethernet node.
Change the driver so it searches the nodes at the right location.
For this to work move the phy nodes in all dts/dtsi over to the new
bus node. Use the following replacement rule:
Replace old full declaration
ðernet0 {
mdio-bus {
...
};
};
and old abbreviated declaration
&mdio {
...
};
simply with the new declaration
&mdio_bus0 {
...
};
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19986
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The mdio controller has now its own target specific device nodes. This
is much closer to upstream notation. Adapt the driver to make use of it.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19986
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Until now the mdio bus is a subnode of the ethernet device. This
coupling is different from upstream and wrong. Ethernet and mdio
are different devices. Additionally differentiate between mdio
controller and mdio bus. To make it clear:
- There is one mdio controller
- With up to 4 busses (on RTL93xx)
Prepare new mdio controller and bus nodes with SoC specific compatibles.
These will be used later when refactoring the mdio driver probing.
Remark! For now only define the first bus for the RTL93xx targets.
So the driver still relies on "rtl9300,smi-address = <x y>;". It will
need much more refactoring to get totally aligned with upstream.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19986
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
While converting the RTL931x SerDes code to the new frontend
access methods, the target specific workarounds where left in
place. The old functions were kept and the phy/sds mapping
was unchanged too. It is time to clean this up
- drop the old functions
- reuse the existing read/write logic
- harden the new functions
For now keep the function naming rtmdio_...__new() as is. This
will be changed in a future commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19973
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
They have the same 0x200 calibration size.
Added various compatible lines in various places to make it clear what
device we're talking about.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19863
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These devices use AR9285, which uses 1f8 as the calibration size, not
440 like newer chips do. Actually the driver mandates a minimum of 200.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19863
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The TP-Link Archer VR1200v (v2) is a low end DSL modem based on the
EcoNet EN751221 processor platform.
While it does have an unlocked bootloader, the factory upgrade feature
requires a cryptographic signature so flashing from the web UI is not
feasible.
The Archer VR1200v (v2) uses a dual-image layout. I have chosen to reuse
this to support dual-boot between OpenWRT and the factory firmware.
Flashing instructions (from bootloader):
Build and then locate the squashfs-sysupgrade.bin image file
Get the length of that file in hex: printf '%X\n' "$(stat -c%s the-file-squashfs-sysupgrade.bin)"
Connect to device with xmodem capability, e.g. picocom --send-cmd lsx -vv -b 115200 /dev/ttyUSB0
Switch device on and press a key within 3 seconds, you should get to a `bldr>` prompt
Type: xmdm 80020000 <file length hex>
Quickly start xmodem and send the file, in picocom that is ctrl+a ctrl+s <paste-the-file-name> enter If the transfer fails to start, wait 30 seconds to a minute for the bootloader prompt to return and then try the command again.
Once the transfer has completed successfully, type the following flash 80000 80020000 <file length hex>
Type `re` or simply restart the device to boot into OpenWRT
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://github.com/openwrt/openwrt/pull/19021
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The SmartFiber XP8421-B is a fiber modem which is available for $20 online
and has 512MB of memory, 256MB of SPI NAND flash and 2 USB 2.0 ports in
addition to ethernet, wifi and XPON.
Because EcoNet is not currently producing evaluation boards, the XP8421-B
stands in as a convenient, low cost, off-the-shelf, representitive example
of the capabilities of the EN751221 econet processor. This is also the
example board that is included in the upstream Linux patchset.
The XP8421-B, and apparently many other devices of this platform, use a
dual-image layout. I have chosen to reuse this to support dual-boot between
OpenWRT and the factory firmware. Certain design decisions were made with
the goal of not overwriting data that is used by the factory OS.
This commit also introduces a utility for switching between OS_A and OS_B
which are used for OpenWRT and Factory OS respectively.
Flashing instructions (from bootloader):
Build and then locate the squashfs-tclinux.trx image file
Get the length of that file in hex: printf '%X\n' "$(stat -c%s the-file-squashfs-tclinux.trx)"
Connect to device with xmodem capability, e.g. picocom --send-cmd lsx -vv -b 115200 /dev/ttyUSB0
Switch device on and press a key within 3 seconds
Enter bootloader username and password: telecomadmin nE7jA%5m
Type: xmdm 80020000 <file length hex>
Quickly start xmodem and send the file, in picocom that is ctrl+a ctrl+s <paste-the-file-name> enter If the transfer fails to start, wait 30 seconds to a
minute for the bootloader prompt to return and then try the command again.
Once the transfer has completed successfully, type the following flash 80000 80020000 <file length hex>
Type go or simply restart the device to boot into OpenWRT
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://github.com/openwrt/openwrt/pull/19021
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
EcoNet EN75xx is a big endian MIPS platform used in XPON (fiber),
DSL, and SIM (3g/4g) applications. Complete GPL vender SDKs exist
for this platform, but are based on Linux 2.6.
The bulk of this submission has already been accepted upstream:
https://patchwork.kernel.org/project/linux-mips/list/?series=960479&state=*
This platform uses a bootloader that is derived from old TrendChip
code. This bootloader implements a frustratingly complex Bad Block
Table which is implemented here in en75_bmt.c
This BMT is not upstreamed because it depends on mtk_bmt framework
which likewise is not upstreamed.
This BMT system rewrites block indexes in flash and if the bootloader
considers it to be corrupted, it will attempt to automatically rebuild
on boot. So without implementing the algorithm, you can't safely use
the disk at all.
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://github.com/openwrt/openwrt/pull/19021
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
RockChip RK3568 ARM64 (4 cores)
1/2GB LPDDR4 RAM
2x 2500 Base-T (PCIe, r8125b)
1 LED (Power)
1 Button (Reset)
Micro-SD Slot
2x USB 3.0 Port
12V DC Jack
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card using
dd.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19990
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add labels wan and cpu for ethernet ports.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19968
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently 5G wireless interface MAC address is incorrect.
Fix by setting MAC address using Factory data.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19968
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Convert NWA50AX Pro to use NVMEM framework for wifi macaddr.
Also remove the unused macaddr@a.
Signed-off-by: Zhi-Jun You <hujy652@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/19982
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Convert NWA50AX Pro to use NVMEM framework for EEPROM/precal.
Signed-off-by: Zhi-Jun You <hujy652@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/19982
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These are already specified in DTS. Only thing missing is
label-mac-device.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19806
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Support in mt76 has existed for quite a while. Use it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19806
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
After trying to implement the gluon support for this device I ended up in a boot loop due to the usable amount of flash left. With this patch layout it uses the unused and empty flash space in the original partiton layout.
The version 3 of this device the RE365 share the same approach to have more usable space.
Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
Link: https://github.com/openwrt/openwrt/pull/18639
Signed-off-by: Sander Vanheule <sander@svanheule.net>
A lot of definitions in the global mach include have been taken over
to the individual drivers. Only a few of the definitions are really
used nowadays. Remove all the unneeded lines.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19995
Signed-off-by: Robert Marko <robimarko@gmail.com>
- shrink data structures
- avoid unnecessary divisions
- support GSO fraglist on tx
Reapply with fixed patch
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use Linux kernel version 6.12 by default for loongarch64 target.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19980
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Boards such as [1] and [2] add an extra Ethernet port to Raspberry Pi (CM)5.
These typically use Realtek PCIe or USB Ethernet NICs. Include kmod-r8169 and
kmod-usb-net-rtl8152 by default to make it easy to configure LAN/WAN ports
with these parts on Raspberry Pi 5.
Because CM5 can fit in the same carrier boards as CM4, also ensure that both
devices have the same Ethernet NIC kmods.
[1]: https://www.waveshare.com/wiki/CM5-DUAL-ETH-MINI
[2]: https://www.waveshare.com/wiki/PCIe_TO_Gigabit_ETH_Board_(C)
Signed-off-by: Elbert Mai <code@elbertmai.com>
Link: https://github.com/openwrt/openwrt/pull/19384
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Certain boards have an at24(-compatible) EEPROM for storing various
parameters like MAC addresses. Enable support for this hardware across
the whole target.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Backport fixes for Airoha pinctrl driver for PHY LED and MDIO bus. This
fix a copy-paste error for PHY LED and a misconfiguration for MT7530
embedded Switch MDIO bus GPIO pin to permit usage of external PHYs.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The RK356x/RK3588 SoCs support up to 10 serial ports.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19917
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Apart from improved power consumption, this fixes the runtime errors
from the pmdomain driver (failed to set idle on domain '%s')
Backport four clk fixes while at it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19925
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All devices supported by the Zynq target have either a Realtek or Marvell
PHY. The Vitesse PHY was enabled when the target was created (2d45ad07fc).
It's not used here, so it's safe to disable it.
Ethernet PHYs used by individual devices are listed below.
Device PHY
AVNET ZedBoard Marvell 88E1518
Digilent Zybo Realtek RTL8211E
Digilent Zybo Z7 Realtek RTL8211E or RTL8211F
Xilinx ZC702 Marvell 88E1116R
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19969
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This was done by executing these command:
$ make kernel_oldconfig CONFIG_TARGET=platform
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19969
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The devices are basically identical. The RAX3000Me can be with
ddr3 RAM.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19760
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds ddr3 build for the ddr3 variant of the CMCC RAX3000Me
router.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19760
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
