RTL8261N is not used by any device in this target. If necessary, newly added
devices should add the kmod-phy-rtl8261n package.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20444
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This option will only take effect when the "separate_ramdisk"
feature was enabled. However, this target does not support
this feature. It is an obvious copy and paste issue.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17832
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There are two spi drivers for en7523/an7581/an7583:
* en7581-snand (spi-airoha-snfi.c)
* en7523-spi (spi-en7523.c)
The first one supports DMA, but until recently it has several nasty
issues. The second do things properly but does not support DMA.
Recently the first driver was greatly improved, so there is no sence
keep both drivers anymore.
This patch removes en7523-spi driver and use DMA capable driver instead.
Unfortunately there is a nasty en7523 specific issue.
We found that some serial console may pull TX line to GROUND during board
boot time. Airoha uses TX line as one of it's BOOT pins. This will lead
to booting in RESERVED boot mode. It was found that some flashes operates
incorrectly in RESERVED mode if DMA used.
This patch also adds a hack that turns off DMA and prints big fat warning
if booting in reserved mode was detected. This slow down flash operations
but does not kill your data.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20365
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows us use more easily port en7581 drivers to en7523.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20365
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch series removes dirty hack that reads flash page settings from
SNFI registers during driver startup.
Before these patches the airoha spi snfi driver needs to know spinand
flash page size. The driver can't get it from spinand subsystem, so the
following approach was implemented:
* bootloader know the flash page size (and some other parameters)
* to operate properly the bootloader writes flash page size (and some
other parameters) to SNFI registers
* bootloader starts linux
* after linux start SNFI registers keeps the values stored by bootloader
* linux snfi driver reads flash parameters from SNFI registers.
This works, but we can do better. It has been proven that flash page size
is actually unnecessary. We can get all required data from dirmap requests.
This patch series drops the hack and do things properly.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20295
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch series greatly improve airoha snfi driver and fix a
number of serious bugs.
Fixed bugs:
* Fix reading/writing of flashes with more than one plane per lun
* Fill the buffer with 0xff before writing
* Fix reading of flashes supporting continuous reading mode
* Fix error paths
Improvements:
* Add support of dual/quad wires spi modes in exec_op(). This also
fix flash reading/writing if dirmap can't be created.
* Support of dualio/quadio flash reading commands
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20295
Signed-off-by: Robert Marko <robimarko@gmail.com>
Continuous reading mode is broken for some spi controllers. There are two
possible bug scenarios:
1) "continuous mode" flash and spi controller without dirmap support,
but with restriction on transfer length in adjust_op_size()
2) "continuous mode" flash and spi controller with dirmap support for a
single flash page
In the first case, any read that exceeds the limit specified in adjust_op_size()
will result in an EIO error. The limit may even be less than a size of a single
flash page. In this case, any read will result in an error.
In the second case, any read larger than flash page size will result in an EIO
error or spinand driver spoofing (because the spi controller driver returns
more bytes than were actually read).
This patch series tries to fix continuous reading (spinand driver side).
Unfortunately these fixes can't resolve "spinand driver spoofing" case.
Spi controller drivers might need fixes as well.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20295
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add missing syscon compatible for scuclk node.
Fix the unit-address of the scuclk node.
This fixes the pcs driver error:
airoha-pcs 1fa08000.pcs: probe with driver airoha-pcs failed with error -22
airoha-pcs 1fa09000.pcs: probe with driver airoha-pcs failed with error -22
Fixes: c3d70b1 ("airoha: en7581: Add support for external PHY")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20190
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The pinctrl driver for airoha was expecting a function name that was
not a string, but was passed one. Removing #string fixed this issue.
Fixes: c5b12fc ("airoha: Introduce support for Airoha AN7583 SoC")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20190
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patch already exists in generic/backport-6.12.
Fixes: 122135b ("airoha: an7581: add support for kernel 6.12")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20190
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
All devices under airoha use dts directory under the target,
so update the default DEVICE_DTS_DIR. Also set the default
DEVICE_DTS based on the SoC name for non-dev boards.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20190
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Introduce initial support for Airoha AN7583 SoC and add all the required
patch for basic functionality of the SoC.
Airoha AN7583 is based on Airoha EN7581 SoC with some major changes on
the PHY handling and Serdes. It can be see as a lower spec of EN7581
with modern and simplified implementations.
All the patch are sent upstream and are pending revision. Support for
PCIe and USB will come later as soon as DT structure is accepted
upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
To correctly init the CPUFreq driver, CPUFREQ_DT is needed. While at it
also enable CPU HOTPLUG kconfig to support hotplug of secondary CPU.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This add a pending version of the Airoha PCS driver to add support for
External PHY. The Airoha PCS driver will receive some minor modification
once we the PCS subsystem will be defined upstream.
Add all the required node for GDM2 and GDM4 and enable the PCS config.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Switch Airoha targets to 6.12 and drop 6.6 support.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20137
Signed-off-by: Robert Marko <robimarko@gmail.com>
en7523 compilation on 6.12 fails with a no prototype warning. Fix this
by declaring max_transfer_size and transfer_one_message static.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20138
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
No functional changes intended.
Fixes warning:
/linux/arch/arm64/boot/dts/airoha/en7581-gemtek-w1700k.dtb: i2c1@1fbf8100 (mediatek,mt7621-i2c): status: 'oneOf' conditional failed, one must be fixed:
['disable'] is not of type 'object'
'disable' is not one of ['okay', 'disabled', 'reserved', 'fail', 'fail-needs-probe']
from schema $id: http://devicetree.org/schemas/dt-core.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20131
Signed-off-by: Robert Marko <robimarko@gmail.com>
The baud rate control on Airoha does not function properly. This
patch enables the inactive code responsible for this. The UART2
baud rate is correct. HSUART3 operates at twice the requested
baud rate. The same problem exists in the current code, so this
doesn't introduce any regression. Support for baud rates higher
than 460800 is still required. This will be added in the future.
Tested on Gemtek W1700k. UART2 and HSUART3 are working fine.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20049
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh patches 6.12 for airoha and econet
Fixes: 122135b964 ("airoha: an7581: add support for kernel 6.12")
Fixes: 73d0f92460 ("kernel: Add new platform EcoNet MIPS")
Signed-off-by: Leo Barsky <leobrsky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/20073
Signed-off-by: Robert Marko <robimarko@gmail.com>
Enable kernel 6.12 as the testing kernel for airoha.
This first commit will largely maintain feature-parity with kernel 6.6.
DTS changes are backwards-compatible with kernel 6.6.
Tested to flash and boot on Gemtek W1700K (#17869).
Signed-off-by: Kenneth Kasilag <kenneth@kasilag.me>
Link: https://github.com/openwrt/openwrt/pull/19038
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Kenneth Kasilag <kenneth@kasilag.me>
Link: https://github.com/openwrt/openwrt/pull/19038
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport fixes for Airoha pinctrl driver for PHY LED and MDIO bus. This
fix a copy-paste error for PHY LED and a misconfiguration for MT7530
embedded Switch MDIO bus GPIO pin to permit usage of external PHYs.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add the NPU and reserved memory node for AN7581 dtsi since it's not
supported.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Major backport of upstream patch for support of multiple feature of the
Airoha Ethernet driver.
Feature backported are TSO, Jumbo packet, Offload and initial Wlan
Offload support.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport trivial fixes from upstream related to pinctrl and ethernet
driver.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport patch adding support for AN7581 Ethernet PHY based on the same
Mediatek embedded Switch PHY.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace thermal patch with upstream version. The thermal maintainer
reported that the sysfs entry are considered deprecated and that slope
and offset should be handled internally to the driver.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backpot upstream patch for Flow Offload support for AN7581 and refresh
all affected patch. To correctly work a dedicated firmware is needed to
use the dedicated Network Coprocessor (NPU).
This also introduce good cleanup and moves the driver in a dedicated
Airoha directory. While currently not totally usable (due to lack of
firmware blob) this is needed to backport support for external PHY/SFP
support.
Refresh all affected patch.
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # tested on Quantum W1700k
Tested-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18166
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport some upstream patch for Airoha ethernet driver in preparation
for Flow Offload support.
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # tested on Quantum W1700k
Tested-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18166
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace PCIe patch with upstream version and update DTS with new PBUS
CSR property now required.
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # tested on Quantum W1700k
Tested-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18166
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Removes the need for a remove function in platform_device.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18660
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
PHY2 led1 is configured to control PHY1's LED. Change it to PHY2.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18361
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_NET_SWITCHDEV option is needed by CONFIG_DSA and some other
options. It is boolean, we have to compile it into the kernel it self.
Activate it for all targets in the generic configuration, it is already
activated for most of them. This allows to install DSA drivers as a
module.
On the ramips/mt7620 target the kernel would grown by 4.5kB.
For some small targets which do not support a DSA switch by default the
option is deactivated.
Link: https://github.com/openwrt/openwrt/pull/17668
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Drop Airoha MTD parser patch as a better solution was agreed with a
fixed partition table.
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # tested on Quantum W1700k
Link: https://github.com/openwrt/openwrt/pull/18112
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cleanup kernel config and drop all unrelated configs. This have the side
effect of fixing the port not going up automatically due to Bridge VLAN
Filtering disabled.
Link: https://github.com/openwrt/openwrt/pull/18112
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
