These devices share the same "compatible" in device tree causing some
incompatibilities (sysupgrades, ASU profile identification), assign a
unique "compatible" and "model" to each variant.
Context:
Commit [1] added each variant's dts compatible to the SUPPORTED_DEVICES
field of the other variant to make easy sysupgrades between these
physically indistinguishable devices variants possible.
But there were found three issues which does not allow this:
- the sysupgrade's stricter check still used in some sysupgrade
paths(this check is being replaced(and redundant) with the newer fwtool's
SUPPORTED_DEVICES check using the info in images METADATA), this check
will fail when sysupgrading from a different board_name(compatible dts)
that the image was created for (image profile name).[2]
- ASU needs unique "dts compatible" to identify the devices profile.
- and an ASU's profile identification limitation when several devices from
a common target share SUPPORTED_DEVICES entries.[3]
There is a proposal for these issues but not yet implemented [4][3].
Until these issues are fixed we won't allow "easy" sysupgrades between
these two device variants.
Commit [5] avoided the ASU profile identification limitation but
missed the required two unique dts compatibles in order to make the two
variants fully work, although not allowing easy sysupgrade between them.
[1]: 8d30e07180
[2]: sysupgrade stricter check https://github.com/openwrt/openwrt/issues/20566#issuecomment-3583555482
[3]: ASU proposal https://github.com/openwrt/asu/pull/1533
[4]: allow easy sysupgrade proposal https://github.com/openwrt/openwrt/pull/20947
[5]: b71f4665cd
Fixes: b71f466 ("mediatek: filogic: fix supported_devices list for gl-mt2500")
Fixes: 8d30e07 ("mediatek: filogic: fix for new GL.iNet GL-MT2500/GL-MT2500A hardware revision")
Fixes: https://github.com/openwrt/openwrt/issues/20566
Fixes: https://github.com/openwrt/asu/issues/1525
Signed-off-by: Mario Andrés Pérez <mapb_@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21842
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7aa1f7e814)
When config_change is set during an active setup (e.g. by a concurrent
reconf call), wdev_mark_up() attempted to call setup() while still in
"setup" state. Since setup() requires state "up" or "down", it silently
returned, leaving the state as "setup". The subsequent wdev_setup_cb()
then treated this as a setup failure, triggering an unnecessary
teardown+restart cycle.
Fix this by removing the config_change handling from wdev_mark_up() and
moving it to wdev_setup_cb() instead. wdev_mark_up() now always
transitions to "up" state. When wdev_setup_cb() runs afterwards and
finds the device already "up" with config_change set, it initiates a
clean re-setup from the "up" state where setup() can run.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 3553eda283)
- no longer write any temporary file for peer gen
- use wg syncconf to update active interfaces (not setconf)
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21784
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 148207730a)
Link: https://github.com/openwrt/openwrt/pull/21840
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Commit 01a87f4bd0 changed the encryption
setting of the default SSID "OpenWrt" from "none" to "open". The correct
setting as per the documentation [1] is "none", though.
While this invalid setting won't cause a wrong hostapd setup, it will
at least cause malfunction in LuCI.
Change the default encryption setting back to "none".
[1] https://openwrt.org/docs/guide-user/network/wifi/basic#encryption_modes
Fixes: 01a87f4bd0
Signed-off-by: Shine <4c.fce2@proton.me>
Link: https://github.com/openwrt/openwrt/pull/21925
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 4ab5fcc04f)
Uninitialized memory led to bogus, huge timestamps being set on files
downloaded with the wget backend. This caused odd issues like 'ls -l'
crashing busybox when attempting to list the .apk file afterwards.
Link: 42f159e67b
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/21874
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit f750e3096f)
The ucode wifi-scripts unconditionally set ieee80211w=1 for psk-sae
and eap-eap2 auth types, ignoring any user-configured value. This
caused ieee80211w=2 (MFP required) to be silently downgraded to 1
(MFP optional) when using sae-mixed encryption.
Change the logic to only set the default of 1 when ieee80211w is not
already configured by the user.
Fixes: https://github.com/openwrt/openwrt/issues/21751
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 1bbb60184d)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add a module for tpm-tis-spi for TCG TIS 1.3 TPM security chips
connected to a regular non-tcg SPI master.
Add imx target compatibility for kmod-tpm.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/21726
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 92a94dc9b0)
Add pending uboot support for the HINLINK H28K.
This fixes the rockchip build again.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 384127320e)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The mobility_domain value generated by ucode differed from the previous
shell script implementation. The legacy shell script used `echo` on the
SSID, which appended a trailing newline.
To maintain roaming compatibility with pre-25.12 releases and OpenWrt
forks in default configuration, update the ucode logic to include this
newline character when generating the default value.
Fixes: #21731
Signed-off-by: Youfu Zhang <zhangyoufu@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21732
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 1d0e2859c5)
KERNEL_DCB was introduced in 40f1db9cb1, however the dcb utility is not
enabled for iproute2. Although DCB is not generally available among
Ethernet cards, not having the dcb utility renders it completely
unchangeable.
On aarch64, it takes ~85.3KiB.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21606
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f0f5525b75)
The `syn_flood` option name is deprecated, `synflood_protect` should
be used instead. firewall3 and firewall4 both support this option since
a long time. LuCI already replaces the option name.
0abcb39b62
Suggested-by: rparge in OpenWrt forum
Link: https://github.com/openwrt/openwrt/pull/21642
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 2ae350b725)
Switchdev driver used by microchipsw supports DCB and has not storage
constraints, so enable kernel and driver DCB support by default.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 4c0c7442db)
This is tri-band WiFi6E capable router. Also Zyxel Nebula managed so no real local GUI. To open device 4 screws must be located uder the label.
Four latches are on front and two on each side. Better start from ethernet port side where 3 small latches are easy to handle.
FCC shows It's identical to WSQ65 sold as Zyxel Multy M6E but that's nowhare to be found yet. WSQ65 is not covered by this PR
Speficiations:
* SoC: Qualcomm IPQ5018
* RAM: 1GB DDR3
* Flash: Winbond W25N02KWZEIR 256MB
* UART: PCB "J3" is located left from front LED strip
(VCC/TX/RX/ /GND) 3.3V 115200n8
* Wi-Fi1: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
* Wi-Fi2: QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
* Wi-Fi3: QCN6122 (2x2:2 6 Ghz 802.11an/ac/ax)
* Ethernet: QCA8337 4xLAN 1Gbit / 1xWAN 1Gbit
* Buttons: WPS , Reset
* LEDs: 13 in total
RGB power, RGB wan, RGB status (cloud), RGB wifi, Green wps
* FCCID: I8803891
*Flash Instructions starts with getting root:
connect uart to J3 connector next to the front LEDs
go to failsafe when this shows up in log:
"Press the [f] key and hit [enter] to enter failsafe mode"
execute:
mount_root
passwd -d root
reboot
logon as root:
look for 'Please press Enter to activate this console.'
login is root password is empty
execute:
fw_setenv DebugFlag=0x1
fw_setenv bootdelay=0x2
passwd -d root
backup ubi partition "rootfs" into safe space
reboot
*OpenWrt installation
stop uboot and execute:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.10
tftpboot *-factory.ubi
flash rootfs
reset
or:
tftpboot *-initramfs-uImage.itb
bootm
use sysupgrade as usual
*restore OEM from backup
stop uboot and execute:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.10
tftpboot *-initramfs-uImage.itb
bootm
transfer rootfs.bin backup and execute:
ubiformat /dev/mtd16 -y -f /tmp/rootfs.bin
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
Link: https://github.com/openwrt/openwrt/pull/21042
(cherry picked from commit f948f71300)
Link: https://github.com/openwrt/openwrt/pull/21440
Signed-off-by: Robert Marko <robimarko@gmail.com>
Broadcom BCM43602 needs certain NVRAM variables to be set to function. Add
a quirk for it and add ASUS RT-AC3200 which has got Broadcom BCM43602 to
the quirk. Thanks to Tom Brautaset for finding the needed variables.
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
(cherry picked from commit cd2ad6c464)
Add ASUS RT-AC3200 and ASUS RT-AC5300 to the set wireless LED behaviour
quirk. ASUS RT-AC3200's wireless chip is different than ASUS RT-AC5300's,
the environment variables for it are 0:ledbh10 and 1:ledbh10.
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
(cherry picked from commit 64b6293eb7)
It is obsolete since the io module was added
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit e06c4125fd)
Link: https://github.com/openwrt/openwrt/pull/21631
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
WiFi 6E (802.11ax) clients cannot discover 6GHz APs operating at
320MHz because the HE Operation element contains uninitialized
center frequency values.
For EHT320 mode, the code sets eht_oper_centr_freq_seg0_idx but not
the corresponding HE values. Later, the HE values are copied from
VHT values, but VHT is not used on 6GHz, leaving he_oper_chwidth
and he_oper_centr_freq_seg0_idx at 0. This causes WiFi 6E clients
to see incorrect channel width information, making the AP invisible
to them during scanning.
Fix this by:
1. Setting he_oper_chwidth to 3 (160MHz) for EHT320 mode
2. Computing he_oper_centr_freq_seg0_idx based on the 160MHz segment
that contains the primary channel
3. Preserving these pre-set values instead of overwriting them with
uninitialized VHT values
WiFi 7 clients continue to see 320MHz operation via the EHT Operation
element, while WiFi 6E clients can now discover and connect at 160MHz.
Signed-off-by: Ryan Chen <rchen14b@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21588
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a8bdb1e6d6)
Package the Microchip SparX-5 switchdev driver as a module.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 9a4c6550a7)
The module exists in ucode and has been present for a while
but has not been enabled. It provides the ucode zlib module
for handling gzip and zlib compression in ucode scripts.
The package is ~ 5Kb. Installed ~18Kb.
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21417
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 16ae5c23e5)
Link: https://github.com/openwrt/openwrt/pull/21608
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Microchip ATF depends on Ruby scripts to generate the FWU monitor HTML
and more, so make sure that host Ruby is available.
We also need to call the scripts directly via Ruby executable as shebang
wont work due to lack of Ruby in the Buildbot container.
Fixes: 5205c0c426 ("microchipsw: lan969x: add Microchip EV23X71A")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 082fe669f7)
LibreSSL 3.9+ has dropped support for X509V3 extension API so cert_create
tool does not compile against it at all.
This was hidden by the fact that it was compiling against OpenSSL on my
host which still has that API, however we do not ship libssl-dev in the
Buildbot containers so compiling against distro OpenSSL is not possible.
So, after a long time trying to find any docs on that API I resorted to
LLM(Gemini 3 Pro) to get it to compile.
Our libcrypto is linked against pthread so we must pass -lpthread as well
for cert_tool.
Fixes: 5205c0c426 ("microchipsw: lan969x: add Microchip EV23X71A")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 410277ca12)
ABI version is added to a package name during packaging, so there's no
need to specify it manually. And nothing explicitly depends on libelf1.
Fixes: d7bf089 ("elfutils: rename libelf1 to libelf")
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/21369
(cherry picked from commit 8cc2743c48)
Link: https://github.com/openwrt/openwrt/pull/21547
Signed-off-by: Robert Marko <robimarko@gmail.com>
