The WAN(eth1) port LED on the Radxa E20C is completely off.
Since the r8169 driver supports configuring LEDs, using it.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Currently, the LED names generated by the r8169 driver are the
network port names renamed by udev, such as enp1s0. Add a hack
patch to restore the interface name to match OpenWrt.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Build kernel module for cs5535 internal audio for target x86 "legacy" also
(so far only for target x86 "geode")
Signed-off-by: Pierre-Emmanuel Frot <piemfrot@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21596
Signed-off-by: Robert Marko <robimarko@gmail.com>
The gmac definition has an offset of 1 compared to the label MAC.
Fixes: a55ab9e134 ("mediatek: filogic: prevent faulty mac address assignment")
Signed-off-by: Maximilian Baumgartner <aufhaxer@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/21560
Signed-off-by: Robert Marko <robimarko@gmail.com>
More rust symbols that are detected using scripts or based on the rust
version have been added. Filter them out.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Link: https://github.com/openwrt/openwrt/pull/21554
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rework the SerDes mode setting to have a better logical structure,
similar to how RTL931x currently does it. Mode setting is grouped into a
MAC setup and IP core setup. Most modes just need to trigger the MAC
setup and then they work, otherwise some complex sequence is needed.
To achieve that, rename several functions and group their content
differently. While at it, rename some constants to use the RTPCS_ prefix.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21565
Signed-off-by: Robert Marko <robimarko@gmail.com>
RTL930x has some helpers which take care of writing the actual mode
value to the corresponding register. They exist for the MAC setup SerDes
mode, the USXGMII submode and the SerDes IP core mode.
To reflect that, adjust the naming of these helpers accordingly. Most
importantly, prefix the helper names with '__'. This is a common
convention to denote helpers/functions which are internal, not intended
for general use and skip certain checks. Those conditions apply to these
helpers. Though they are still used quite often here, this might change
with further cleanups.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21565
Signed-off-by: Robert Marko <robimarko@gmail.com>
Completely replace usage of PHY_INTERFACE_MODE_* in the vast amount of
calibration functions with the SerDes hardware mode.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21565
Signed-off-by: Robert Marko <robimarko@gmail.com>
Set and configure the SerDes mode using the SerDes hardware mode types
instead of PHY_INTERFACE_MODE_*.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21565
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use SerDes hardware mode in RTL930x SerDes TX config instead of
PHY_INTERFACE_MODE_* modes.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21565
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to using the SerDes hardware mode in RTL930x SerDes patching aka
rtpcs_930x_sds_patch.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21565
Signed-off-by: Robert Marko <robimarko@gmail.com>
Start using the SerDes hardware in the RTL930x SerDes setup entrypoint.
Use the generic mapper (which will be moved out later to pcs_config) to
determine the mode. In the next steps, switch to solely using that
step-by-step.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21565
Signed-off-by: Robert Marko <robimarko@gmail.com>
Convert the update_counter() and net_irq() functions to the
new prefix. For better readability rename "cntr" to "counter".
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21569
Signed-off-by: Robert Marko <robimarko@gmail.com>
The hardware reset is a combined function for all device families.
So it uses several family specific branches to decide what is
really needed. Refactor this into device specific variants to make
it easier to understand.
The cpu port and nic reset sequence is the same for all families.
Provide this with a dedicated function.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21569
Signed-off-by: Robert Marko <robimarko@gmail.com>
The cameo based RTL83xx devices have a simple U-Boot that only
supports gzip compression. Actual models are mainly D-Link
DGS-1210 and the Apresia Light GS120GT-SS. Reduce the image
size by ~1MB by switching over to lzma compression and rt-loader.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21577
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
SoC: Qualcomm IPQ6010 1.8GHz
RAM: K4A8G165WC-BCTD x2 2GiB
ETH: QCA8075 (3x LAN, 1x WAN)
Flash: ICMAX 8GB eMMC
Power: DC 12V 2A
USB: 1x 3.0
Button: Reset
Flash instructions:
1. Download the initramfs image, rename it to
initramfs.itb, host it with the tftp server.
2. Enter "jdmt018R" to interrupt U-Boot
when the following statement appears:
"disabled console and autoboot in 2 seconds"
3. Run these commands in U-Boot console:
tftpboot initramfs.itb
bootm
4. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/19840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
SoC: Qualcomm IPQ6010 1.8GHz
RAM: K4A4G165WF-BCTD x2 1GiB
Flash: FORESEE 128GB/256GB eMMC
ETH: 4x 1Gbps + 1x 2.5Gbps
WLAN1: QCN5022 2.4GHz AX 2x2
WLAN2: QCN5052 5.8GHz AX 2x2
WLAN2: QCN9024 5.2GHz AX 4x4
Button: Reset, Screen, Wps
Power: DC 12V 3A
USB: 1x 3.0
Flash instructions:
1. Download the initramfs image, rename it to
initramfs.itb, host it with the tftp server.
2. If the stock firmware version is 4.3.0.r4211
or higher, enter "jdmt018R" to interrupt
U-Boot when the following statement appears:
"disabled console and autoboot in 2 seconds"
3. Run these commands in U-Boot console:
tftpboot initramfs.itb
bootm
4. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/19840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
SoC: Qualcomm IPQ6000 1.2GHz
RAM: NT52CB256MB16DP 512MiB
Flash: FORESEE 64GB/128GB eMMC
ETH: QCA8075 (3x LAN, 1x WAN)
WLAN1: QCN5022 2.4GHz AX 2x2
WLAN2: QCN5052 5GHz AX 2x2
Power: DC 12V 2A
Button: Reset, Wps
USB: 1x 3.0
Flash instructions:
1. Download the initramfs image, rename it to
initramfs.itb, host it with the tftp server.
2. If the stock firmware version is 4.3.0.r4211
or higher, enter "jdmt018R" to interrupt
U-Boot when the following statement appears:
"disabled console and autoboot in 2 seconds"
3. Run these commands in U-Boot console:
tftpboot initramfs.itb
bootm
4. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/19780
Signed-off-by: Robert Marko <robimarko@gmail.com>
Match the unit address of both QSDK switch ports with the node's port_id
property. Purely cleanup, no functional change.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21456
Signed-off-by: Robert Marko <robimarko@gmail.com>
The imagebuilder cannot compile source, so we must guard against
generation of artifact targets that require this. Without this
guard we see an error when building the zyxel,gs1920-24hp-v1 profile.
Create standalone rt-loader, loading uimage from address 0xb40c0000
mips-openwrt-linux-musl-gcc -fpic -msoft-float -Iinclude -c -o ... src/startup.S
make[4]: mips-openwrt-linux-musl-gcc: No such file or directory
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21556
Signed-off-by: Robert Marko <robimarko@gmail.com>
The gmac definition has an offset of 1 at the moment. This leads to an
off by one error in downstream projects that rely on the package label mac.
Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
Link: https://github.com/openwrt/openwrt/pull/21543
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rename some of the net_device_ops to the new driver prefix.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21476
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rename transmit related functions with the new prefix.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21476
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Convert the mac functions to the new prefix.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21476
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rename the header tag encoding/decoding functions according
to the new prefix naming convention.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21476
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All Realtek drivers use ctrl (control) als the central driver
structure. Align that for the ethernet driver. Additionally
use the rteth prefix for the device independent structure
definition. Its current prefix "rtl838x_" is only confusing.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21476
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is currently a mismatch in the detection of the chip type.
rt-loader and the kernel give different revisions. E.g.
rt-loader: Running on RTL9313 (chip id 6567A) with 256MB
kernel: Realtek RTL9313 rev B (6567) SoC with 256 MB
Realtek internal version numbering is
- for RTL838x: 1=A, 2=B, ...
- for others: 0=A, 1=B, ...
rt-loader does not differentiate that. Adapt the calculation to
give a consistent picture.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21498
Signed-off-by: Robert Marko <robimarko@gmail.com>
Initialization of the RTL8214FC was coded like "put the cart
before the horse". Configuration was called from probing
and only when called for the last port.
Testing showed that there is no need to overcomplicate things.
Reorganize the setup as follows:
- Let probe() & config() do what they are meant for
- Split the config part between a package and a port sequence
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21508
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RTL8214FC is initialized with a minimum driver sequence.
The firmware usage has been made obsolete. Drop leftovers.
These include:
- old code
- firmware file
- kernel config (to include the firmware file into the build)
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21508
Signed-off-by: Robert Marko <robimarko@gmail.com>
There are currently two code paths to initialize the RTL8214FC. One is
for RTL838x, the other for RTL839x. With the recently added minimum
setup sequence the phy will come up and pass traffic on any device.
Use this als the reference implementation and drop the usage of the
magic firmware based setup.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21508
Signed-off-by: Robert Marko <robimarko@gmail.com>
For the GS1920 the build system throws errors like
../dts/rtl8392_zyxel_gs1920-24hp-v1.dts:256.19-29:
Warning (reg_format): /switch@1b000000/ports/port@0:reg:
property has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
The dts misses the address and size properties for the
ports section. Fix that.
Fixes: 2a55846 ("realtek: add support for ZyXEL GS1920-24HPv1")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21534
Signed-off-by: Robert Marko <robimarko@gmail.com>
The patch 950-0019-BCM2708-Add-core-Device-Tree-support.patch creates a
symbolic link. It looks like quilt does not support this and never
refreshed it.
I removed the symbolic link, refreshed the patch and then added it
back again.
Link: https://github.com/openwrt/openwrt/pull/21431
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Implement the .get_link_ksettings to get the rate, duplex, and
auto-negotiation status.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/21530
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some mpc85xx boards still boot with failsafe configured on a non-LAN
interface. Align the preinit interface with the first DSA port or the
interface that LAN is connected to.
This makes failsafe reachable on devices where the default selection does
not map to the primary LAN port.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21516
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for the Airpi AP3000M 5G CPE based on MediaTek MT7981B.
Specifications:
SoC: MediaTek MT7981B (dual-core ARM Cortex-A53)
RAM: 1GB DDR4
Storage: 8GB or 16GB eMMC
Ethernet: 1x 2.5GbE LAN, 1x 1GbE WAN
Wireless: 2.4GHz/5GHz 802.11ax
Buttons: Reset, WPS
LEDs: System, 2.4GHz WiFi, 5GHz WiFi
Cooling: PWM-controlled fan
Expansion: M.2 slot for 5G modem
The factory partition (mmcblk0p2) is empty in stock firmware.
Execute via SSH before flashing OpenWrt:
```
dd if=/lib/firmware/MT7981_iPAiLNA_EEPROM.bin of=/dev/mmcblk0p2 bs=4k count=1
MAC addresses
```
Fixed MAC addresses are derived by macaddr_generate_from_mmc_cid.
Installation via U-Boot web page
Set static IP 192.168.88.2/255.255.255.0 on your computer.
Connect to the 1GbE port (WAN) and hold the reset button while booting the device. Wait for about 6 seconds, and release the reset button.
Open U-boot web page on your browser at http://192.168.88.1
Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
Wait for automatic reboot.
Installation via sysupgrade
Flash the sysupgrade file via LuCI upgrade page without saving the settings.
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21397
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Newer Cudy WR3000H units have a Motorcomm YT8821 PHY instead of a
Realtek PHY on the WAN port. Before this commit, the Motorcomm PHY
could not be autodetected by the kernel -- the PHY would show up as
just a generic clause 45 PHY and the proper driver would not be loaded.
The cause of the detection failure likely was that the YT8821 PHY was
held in reset during PHY detection. To fix this, move the reset GPIO
definition to the MDIO bus level. This reset line is deasserted before
the autodetection process, see also [1]. With this change, both Realtek
and Motorcomm PHYs can be supported with a single device tree.
[1]: https://lore.kernel.org/all/20251119134750.394655-1-horatiu.vultur@microchip.com/
Signed-off-by: Jakub Vaněk <linuxtardis@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21399
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Recent Cudy WR3000H v1 units have a Motorcomm YT8821 2.5G PHY for
the WAN interface instead of the RTL8221B PHY used in earlier units,
so add kmod-phy-motorcomm to be able to use it.
Signed-off-by: Andrew MacIntyre <andymac@pcug.org.au>
[linuxtardis@gmail.com: slightly reworded the commit description]
Signed-off-by: Jakub Vaněk <linuxtardis@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21399
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The interfaces attribute of the mdio bus held the information
about the connection mode (qsgmii, sgmii, ...). This was only
used during the old RTL930x setup. Drop it because it is not
needed any longer.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21469
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Cleanup the RTL930x polling setup. Make use of the
new phy fixup helper to initialize the polling registers.
As an integral update to the logic before only write
register bits that are really in scope. This might save
some bits set by U-Boot.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21469
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The mdio driver currently initializes the phy polling registers
with some nasty magic. It identifies the interface mode from the
dts and draws some strange conclusions.
Looking at the SDK one can see that this is basically dependent
of the attached phy type. So the code location is quite right
inside the mdio driver.
Provide a new get_phy_info() function that determines the phy
characteristics that are important for the polling unit . It will
be later needed by the RTL93xx setup code.
Some explanation about the fields of the structure:
- has_res_reg: phy has a special Realtek resolution polling
register. It is unclear if this gives more details or if it
simply allows faster polling.
- has_giga_lite: This is a phy that allows for Realtek proprietary
1G/2.5G lite connectivity. In this case data is only transmitted
over two wire pairs.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21469
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Currently there are several places where the driver uses the
classic "i" as iterator. In these cases where it iterates
phy ports use "addr" instead to make it easier to read. Do
the same for the smi bus. Additionally forthcomming commits
will show nicer diffs.
While we are here fix the initialization sequence of the private
structure. There is no need to set data to zero that has already
been zero-allocated before. Instead initialize smi_bus[] with
a value of "-1" to denote that a phy is not in scope. This is
essential as some functions already have a matching check in
place.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21469
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The mdio driver was carved out from the ethernet driver long
ago. Remove some leftover defines.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21502
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Mark T4240RDB u-boot variants as device-built and avoid installing them into rootfs.
Without this buildbot crashes during package install with:
ERROR: unable to select packages:
u-boot-fsl_T4240RDB-nor (no such package):
required by: world[u-boot-fsl_T4240RDB-nor]
u-boot-fsl_T4240RDB-sdboot (no such package):
required by: world[u-boot-fsl_T4240RDB-sdboot]
Fixes: c5d3d5fe28 ("package: u-boot: initial support for qoriq arch")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21514
Signed-off-by: Robert Marko <robimarko@gmail.com>
The mac_addr variable was not zero-initialized, causing weird side effects
when the memory contents were a valid MAC address.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Link: https://github.com/openwrt/openwrt/pull/21504
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The realtek target uses some functions marked __init for initialization.
However, that means they can only be called once when compiled in and
afterwards the memory occupied by them is freed and potentially reused.
Some "impossible" (code at a given location can't crash in the way it
does) crashes can be caused by this because upon re-execution of those
functions, garbage gets executed. Such re-execution can happen for
deferred probes or repeated probes.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Link: https://github.com/openwrt/openwrt/pull/21504
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Until now the RTL8214FC is initialized either by U-Boot (all
devices) or by some magic firmware file (RTL838x). On RTL839x
devices without U-Boot (e.g. ZyXEL GS1920) this PHY cannot
be used.
Provide the most basic setup sequence for RTL839x so that
copper/fiber work. Later it can be taken over for all devices
and the firmware helpers can be dropped.
Remark! This should not (but might) break RTL839x devices with
RTL8214FC U-Boot setup.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21435
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
