Hardware
--------
RockChip RK3568 ARM64 (4 cores)
1/2GB LPDDR4 RAM
2x 2500 Base-T (PCIe, r8125b)
1 LED (Power)
1 Button (Reset)
Micro-SD Slot
2x USB 3.0 Port
12V DC Jack
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card using
dd.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19990
(cherry picked from commit d76a774270)
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20618
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The High-Speed SD mode stability issue should have been fixed.
Increase the MMC max-frequency to improve the IO speed. We can
still use the sysfs to limit the clock frequency, e.g.
root@OpenWrt:~# echo 25000000 > /sys/kernel/debug/mmc0/clock
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18896
(cherry picked from commit 143cfd6113)
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20258
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The MT7628 programing guide shows that the correct DTOC unit is
1048576 clocks instead of 65536 clocks. This value is also used
by linux upstream mtk-sd driver. Correct the DTOC register and
also round up its value.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18896
(cherry picked from commit e69c867cdf)
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20258
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- Fix MMC bus IO voltage. The GPIO voltage of mt762x series SoCs
is fixed 3.3V. There are no visible registers that can control
the voltage level. Also add "no-1-8-v" property to indicate that
MMC controller doesn't support 1.8V IO.
- Drop useless property "enable-active-high". These dummy fixed
voltage regulators are not controlled by the GPIO. We don't need
to set the GPIO polarity.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18886
(cherry picked from commit afdf88b9a1)
[rebased upon 24.10 branch]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20258
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that we have a board file, add calibration variant for TP-Link
Archer C60 v2 and add ipq-wifi package for it.
Tested-by: Semih Baskan <strstgs@gmail.com>
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20496
Link: https://github.com/openwrt/openwrt/pull/20497
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, building at91 subtargets via image builder will fail as the
required built at91bootstrap is not present in the image builder at all
since its presumed to be in the binary directory which obviously does not
exist yet.
So, lets install the at91bootstrap binary into image staging directory and
use that instead
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a947be41b7)
Currently, building at91 subtargets via image builder will fail as the
required built u-boot is not present in the image builder at all since its
presumed to be in the binary directory which obviously does not exist yet.
So, lets install the u-boot binary into image staging directory and use
that instead.
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 4724331d70)
Currently, kmod-usb-ohci,kmod-at91-udc and kmod-usb-gadget-eth are included
as the default packages for all at91 subtargets.
However, this is breaking image builder as kmod-at91-udc is not being built
on sama7 since it depends on USB_SUPPORT and sama7 does not have USB support
enabled in the kernel as its not supported upstream so its not even
selectable in the config.
So, move to include these as default packages only for sama5 and sama9x as
both of those have USB support enabled.
Fixes: #18407
Link: https://github.com/openwrt/openwrt/pull/18413
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 02d3aa72bb)
Now that all packages that relied on the skip mechanism are selected
via BUILD_DEVICES or by defaulting for the subtarget drop them from
individual DEVICE_PACKAGES so that Image Builder works again for armv7.
Fixes: #18411
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8cb7919a13)
Now that all packages that relied on the skip mechanism are selected
via BUILD_DEVICES or by defaulting for the subtarget drop them from
individual DEVICE_PACKAGES so that Image Builder works again for armv8_64b.
Fixes: #18412
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit c04eaad12a)
Currently, bcm63xx-cfe is being installed into kernel build dir, however
that does not work for Image Builder as only certain artifacts from kernel
build dir are included in Image Builder.
So, simply install bcm63xx-cfe into image staging dir so its artifacts can
be used in Image Builder as well.
Fixes: #18408Fixes: #18409
Link: https://github.com/openwrt/openwrt/pull/18463
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 4a7de50769)
The imagebuilder is not intended to build initramfs images. Some
profiles attempt to do this and succeed, due to buildroot leaking
the initramfs-kernel into staging_dir; others attempt it, but fail
due to not having initramfs binaries present in the imagebuilder.
Fix this by adding an explict guard around the unsupported generation
of the initramfs images. This saves space and time during imagebuilder
runs, fixes those that are currently broken and protects against future
breakage for profiles that inadvertently work now.
Fixes: https://github.com/openwrt/openwrt/issues/20151
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20347
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit f6e0f57be0)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds led aliases for failsafe and upgrade. Before this change the
leds stayed dark in both situations.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20441
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 1afe4ba623)
Link: https://github.com/openwrt/openwrt/pull/20454
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set the label-mac-device to be able to easily fetch the mac-address of
the device, which is printed on the bottom of the case.
While at it, remove the TODO - the ethernet0 alias is needed to get the
mac from bootloader.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20441
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit deca8fd24b)
Link: https://github.com/openwrt/openwrt/pull/20454
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
backport from kernel 6.12
ksmbd.mount will give each interfaces list and bind_interfaces_only flags
to ksmbd server. Previously, the interfaces list was sent only
when bind_interfaces_only was enabled.
ksmbd server browse only interfaces list given from ksmbd.conf on
FSCTL_QUERY_INTERFACE_INFO IOCTL.
Signed-off-by: Andrea Pesaresi <andreapesaresi82@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20377
(cherry picked from commit 711e14af79)
Link: https://github.com/openwrt/openwrt/pull/20442
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds the required image receipt to generate a vendor ui compatible
initramfs-factory image, that can be used to flash the final sysupgrade
image.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20409
Signed-off-by: Robert Marko <robimarko@gmail.com>
CONFIG_MTD_CFI was disabled in p1010 subtarget.
It causes problem with Aerohive BR200-WP router.
This patch enables CONFIG_MTD_CFI in p1010 config-default file.
Fixes: e9dd6da916 ("mpc85xx: p1010: add missing symbols")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20419
(cherry picked from commit f21e8158fb)
Link: https://github.com/openwrt/openwrt/pull/20428
Signed-off-by: Nick Hainke <vincent@systemli.org>
This patch resolves the LAN port not initializing on the
FriendlyElec NanoPI R4S, especially during warm reboots.
Upstream commit patch is based on:
c3fe7071e1
I've experienced the LAN port failing to initialize from a cold boot and
after a reboot. Other users have reported this issue on
https://forum.openwrt.org/t/nanopi-r4s-rk3399-is-a-great-new-openwrt-device/79143.
The NanoPI R4S has its LAN port connected to the RK3399 via PCIE. Since the
PCIE lanes don't initialize correctly after reboot, the LAN port
doesn't initialize.
Signed-off-by: Timothy Feierabend <tim.feierabend@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20406
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit 7ef19bb9cd)
Link: https://github.com/openwrt/openwrt/pull/20418
Signed-off-by: Robert Marko <robimarko@gmail.com>
Function remove_oem_ubi_volume was called before CI_UBIPART variable was defined.
Fixes: df1f6e1e18 (qualcommax: ipq807x: Remove OEM UBI volume before upgrade for Linksys MX devices)
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18090
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20086
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use 'remove_oem_ubi_volume' function to remove OEM UBI volume before upgrade.
This allows to upgrade even if we have OEM firmware on the second partition.
Applies to Linksys MX4200/MX4300/MX5300/MX8500.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14720
Link: https://github.com/openwrt/openwrt/pull/20086
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that we have a board file, add calibration variant for TP-Link
Archer C59 v1 and add ipq-wifi package for it.
Tested-by: Mateusz Jończyk <matjon@users.noreply.github.com>
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20401
Signed-off-by: Robert Marko <robimarko@gmail.com>
i(cherry picked from commit 2a44808374)
Link: https://github.com/openwrt/openwrt/pull/20407
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a smart door lock device equipped with OpenWrt 14.07 OEM
modified version Qdwrt
The OEM has closed down, This commit is intended to maximize the
remaining value of these devices. It can flash OpenWrt to become
an AP
Specification:
- SoC: MediaTek MT7628NN
- Flash: 8 MB
- RAM: 64 MB
- Power: DC 5V - 25V
- Ethernet: 1 x RJ45 (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only
- On-Board LED:
Status 1: GPIO/43 active-low
Status 2: GPIO/44 active-low
Power: AlwaysOn
- Button:
WPS / RESET: GPIO/14 active-low
- Bluetooth: CC2541 via UART1 (ttyS1) and GPIO/26-29
- RFID: MF RC522 on I2C@28
- RTC: DS1339 on I2C@68
- Shell (via CON1 cable)
- LED (Swipe card area):
- Green GPIO/3 active-high
- Red GPIO/11 active-high
- Matrix keypad: (active-low)
GPIO/20 GPIO/21 GPIO/19 (Rows)
GPIO/24 1 2 3
GPIO/25 4 5 6
GPIO/22 7 8 9
GPIO/23 BACK 0 ENTER
(Cols)
- UART: 1 x UART on PCB - 57600 8N1
- GPIO Relay: GPIO/42 active-high
- GPIO Buzzer: GPIO/15 active-high
Warning:
The original firmware does not use the device tree.
This device tree is written based on the content of /sys/devices/platform
and has been tested
Note:
- On the device, matrix keypad rows actually are columns, and the columns actually are rows
- The key code of the CLEAR key of the matrix keypad is BACK in the original firmware.
Issue:
- No drivers in mainline kernel for RFID and Bluetooth.
Flash Instruction:
Using SSH/Telnet:
1. Connect the board to the computer via RJ45 Ethernet
2. Login 10.10.10.1 with root password "szqdingnet123" (SSH Port 22, Telnet Port 9900)
3. Download openwrt firmware on the computer.
4. Setup a http server on computer. And use wget download openwrt firmware from computer
5. Use command "mtd -r write openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin firmware"
to flash
Using U-Boot WebUI:
1. Configure PC with a static IP address 10.10.10.2/24.
2. Open http://10.10.10.1
3. Use "mkqdimg -B qc202 -f openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin" to
make image.
4. Upload factory.bin via U-Boot WebUI.
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-qianding-smart-locker-and-flash.html
Original U-Boot firmware image tools:
https://gitlab.com/CoiaPrant/mkqdimg
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17471
(cherry picked from commit b2f814fed4)
Link: https://github.com/openwrt/openwrt/pull/20159
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
After extracting the EEPROMs of different devices, only the 0x4 address is unique.
Use the 0x4 address as the LAN address, and the LAN+1 address as the WAN address.
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20256
(cherry picked from commit c907c7c9b3)
Link: https://github.com/openwrt/openwrt/pull/20257
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
According to the MT7628 hardware datasheet:
- GPIO/4 was originally used for I2C, but is now used as the Modem Power.
- GPIO/5 was originally used for I2C, but is now used as the SIM card select. (n/a for this device)
- GPIO/6 was originally used for SPI CS1, but is now used as the Serial mode switch.
- GPIO/36 was originally used for PERST, but is now used as the GPS OE. (n/a for this device)
- GPIO/38 was originally used for WDT, but is now used as the Modem2 Power. (n/a for this device)
- GPIO/44 was used for WLED_AN, but is now controlled by `gpio-leds`.
Corrected pinctrl to ensure it works properly in the future.
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20256
(cherry picked from commit 44c79d094f)
Link: https://github.com/openwrt/openwrt/pull/20257
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
