The Plasma Cloud PSX10 Switch is a 8 + 2 port multi-GBit switch with
8x 10/100/1000/2500BaseT Ethernet ports and 2x SFP+ module slot.
Hardware:
- RTL9302C SoC
- Macronix MX25L25645G (32MB flash)
- Winbond W632GU6NB-12 (256MB DDR3 SDRAM - only 128 MB configured*)
- 2x RTL8224 4x 10m/100m/1/2.5 Gigabit PHY
- SFP+ 2x 10GBit slot
- IC+ IP8008 POE+ PSE controller
The switch is powered by 54 Volts 2.77A barrel connector. The internal TTL
serial connector can be used to access the terminal. Pins from 1: TX RX
(unused) GND. Serial connection is via 115200 baud, 8N1.
A reset button is accessible through a hole in the front panel.
*) Only 128 MB of RAM are currently configured because there were
infrequent random memory corruptions detected when using memtester with a
256 MB DT configuration. This could also be reproduced with RTLSDK.
Installation
------------
* The device can be flashed by using sysupgrade command. Either from the
original vendor firmware or using an initramfs (see "Debug")
* Connect serial as per the layout above. Connection parameters: 115200 8N1
* The image must be copied using scp to /tmp of the device
scp openwrt-realtek-rtl930x-plasmacloud_psx10-squashfs-sysupgrade.bin root@[IP address of the device]:/tmp/
* start sysupgrade without saving the original vendor configuration
sysupgrade -n /tmp/openwrt-realtek-rtl930x-plasmacloud_psx10-squashfs-sysupgrade.bin
Installation via u-boot
-----------------------
If you have an TFTP server connected to the switch, it is possible to
directly install the device using the factory image from u-boot
# setup networking and IP of TFP server
rtk network on
setenv ipaddr 10.100.100.99
setenv serverip 10.100.100.20
# get factory image
tftp 0x84000000 factory.bin
# erase firmware partitions
sf probe 0
sf erase 0x100000 0x01f00000
# write firmware to both partitions
sf write ${fileaddr} 0x100000 ${filesize}
sf write ${fileaddr} 0x1080000 ${filesize}
# adjust the boot commands
setenv bootargs "mtdparts=spi0.0:896k(u-boot),64k(u-boot-env),64k(u-boot-env2),15872k(inactive),15872k(firmware2)"
setenv bootcmd "rtk init; bootm 0xb5080000"
# restart
reset
Debug
-----
* Connect serial as per the layout above. Connection parameters: 115200 8N1.
* A tftp server is required, tftpd-hpa works well.
* Power the device, at U-Boot start rapidly hit Esc key to stop autoboot
* Enable network:
rtk network on
* Change ip address of device:
setenv ipaddr 192.168.1.6
* Download initramfs from TFTP server:
tftpboot 0x84000000 192.168.1.111:openwrt-realtek-rtl930x-plasmacloud_psx10-initramfs-kernel.bin
* Boot loaded file:
bootm 0x84000000
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Co-developed-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Plasma Cloud PSX8 Switch is a 8 port multi-GBit switch with
8x 10/100/1000/2500BaseT Ethernet ports.
Hardware:
- RTL9302C SoC
- Macronix MX25L25645G (32MB flash)
- Winbond W632GU6NB-12 (256MB DDR3 SDRAM - only 128 MB configured*)
- 2x RTL8224 4x 10m/100m/1/2.5 Gigabit PHY
- IC+ IP8008 POE+ PSE controller
The switch is powered by 54 Volts 2.77A barrel connector. The internal TTL
serial connector can be used to access the terminal. Pins from 1: TX RX
(unused) GND. Serial connection is via 115200 baud, 8N1.
A reset button is accessible through a hole in the front panel.
*) Only 128 MB of RAM are currently configured because there were
infrequent random memory corruptions detected when using memtester with a
256 MB DT configuration. This could also be reproduced with RTLSDK.
Installation
------------
* The device can be flashed by using sysupgrade command. Either from the
original vendor firmware or using an initramfs (see "Debug")
* Connect serial as per the layout above. Connection parameters: 115200 8N1
* The image must be copied using scp to /tmp of the device
scp openwrt-realtek-rtl930x-plasmacloud_psx8-squashfs-sysupgrade.bin root@[IP address of the device]:/tmp/
* start sysupgrade without saving the original vendor configuration
sysupgrade -n /tmp/openwrt-realtek-rtl930x-plasmacloud_psx8-squashfs-sysupgrade.bin
Installation via u-boot
-----------------------
If you have an TFTP server connected to the switch, it is possible to
directly install the device using the factory image from u-boot
# setup networking and IP of TFP server
rtk network on
setenv ipaddr 10.100.100.99
setenv serverip 10.100.100.20
# get factory image
tftp 0x84000000 factory.bin
# erase firmware partitions
sf probe 0
sf erase 0x100000 0x01f00000
# write firmware to both partitions
sf write ${fileaddr} 0x100000 ${filesize}
sf write ${fileaddr} 0x1080000 ${filesize}
# adjust the boot commands
setenv bootargs "mtdparts=spi0.0:896k(u-boot),64k(u-boot-env),64k(u-boot-env2),15872k(inactive),15872k(firmware2)"
setenv bootcmd "rtk init; bootm 0xb5080000"
# restart
reset
Debug
-----
* Connect serial as per the layout above. Connection parameters: 115200 8N1.
* A tftp server is required, tftpd-hpa works well.
* Power the device, at U-Boot start rapidly hit Esc key to stop autoboot
* Enable network:
rtk network on
* Change ip address of device:
setenv ipaddr 192.168.1.6
* Download initramfs from TFTP server:
tftpboot 0x84000000 192.168.1.111:openwrt-realtek-rtl930x-plasmacloud_psx8-initramfs-kernel.bin
* Boot loaded file:
bootm 0x84000000
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Co-developed-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Plasma Cloud devices use a dual-firmware regions/slots boot mechanism. On
APs, the u-boot is "intelligent" and checks the NOR/NAND partitions (kernel
+ rootfs) for corruption via "datachk". If validation fails, the bootloader
automatically switches to the fallback partition.
On Realtek-based switches, this "datachk" helper is not available.
However, the bootloader still supports two firmware regions/slots.
When flashing a new image, the "inactive" partition is written instead of
overwriting the active one. If no "inactive" partition exists but
"firmware1" is present, the bootloader always treats "firmware1" as
fallback. Only after a successful flash is the `u-boot-env` updated to
select the newly written partition.
On reboot, the bootloader loads the kernel from the new partition and
passes `mtdparts` information as the kernel cmdline. The Plasma Cloud
switch device tree does not override this with a `bootargs` property, so
the active partition layout is honored from cmdline.
Since offsets, sizes, and names of partitions match between the device tree
and cmdline (except the inactive slot), properties and nodes such as
`nvmem-cells` or `compatible` remain fully usable.
This mechanism also allows switching back to the old firmware slot. For
example, if `firmware1` is currently active (`/proc/mtd` shows it), it can
be switched to slot 2 using:
. /lib/upgrade/upgrade_dualboot.sh
set_boot_part 2
reboot
Firmware upgrades use standard `sysupgrade` tarballs, chosen for
compatibility with vendor images. In theory, one can switch between vendor
and OpenWrt with:
sysupgrade -n /tmp/*-squashfs-sysupgrade.bin
Note: configuration files must not be preserved, as they are not compatible
with vanilla OpenWrt.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To be able to read out the ethaddr from the u-boot environment for MAC
address configuration, it is required to also enable the NVMEM layout
parsing code for the U-Boot env layout.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The function of_get_mac_address is not taking care of evaluation the nvmem
address before trying to read out the mac-address properties. The driver
must check whether the return code is -EPROBE_DEFER and stop the probing
process in that case. If the nvmem-cell related driver code finished, the
probe can be redone ad the correct mac-address will appear for the device.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add calibration variant and ipq-wifi package for Xiaomi AIoT AC2350
Signed-off-by: Igor Dyatlov <dyatlov.igor@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19707
Signed-off-by: Robert Marko <robimarko@gmail.com>
When a wifi-iface section is used either for multiple vifs or MLD links,
make it possible to configure the per-radio/link macaddr.
When MLO is enabled, the main macaddr is used for the MLD interface.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
It's also a bit funny matching against phy0 and phy1 when both differ
between ath9k and ath10k.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19862
Signed-off-by: Robert Marko <robimarko@gmail.com>
33fb6c738bc4 P2P2: Enable some testing parameters without CONFIG_TESTING_OPTIONS
56616c4183a6 P2P2: Update device name with USD device found
1d791939dcdf Cancel pending connect radio work when network is removed
8235e21d7fe3 P2P: Fix preferred frequency list size handling in p2p_check_pref_chan()
4bc754d9c727 Add QCA vendor interface to enable/disable TX power limit
d65f5705df98 Add QCA vendor attribute to disable A-MSDU address check validation
74881765b7fb nl80211: Use i802_bss in qca_set_allowed_ap_freqs() to use correct ifindex
ca8303135cbb P2P2: Set P2P mode to the driver on P2P GO device
063ae7af68dc ACS: Fix incorrect index calculation for primary channel
4aa3a58377c1 ACS: Validate all channels in a segment before selection
02c9d3376224 ACS: Extend support to exclude 6 GHz non-PSC in non-offloaded ACS
307365eb57bb tests: Add test for ACS exclude 6 GHz non-PSC
0721e4886316 Add QCA vendor attribute to configure EHT RTWT support
76b39db44c77 QCA vendor attribute to configure BTM MLD Recommendation For Multiple APs support
2faeffdeca22 AP MLD: Properly deinit sm of non-ML STA connected to ML AP
e4f4e5a872a5 AP MLD: Fix STA's flag wrongly updated in SME-in-driver cases
ec6cade42c0f Increase buffer size to handle long freq_list entries in config
0522585da7b0 Write freq_list as per-network item in wpa_supplicant.conf
5e527704b912 Use SCS reconfiguration logic under CONFIG_NO_ROBUST_AV
5d6214a724c1 PASN: Clear driver/firwmare ranging context if PASN Auth 1 fails
14dc782d50db DPP: Avoid generating DPP shared secret(z) for non-association links
40326b60b17a RSNO: Allow OWE to be configured in RSN overrides in AP processing
acadef1b04d5 hostapd_cli: Open a new hostapd connection on ping failure when using -a
ac0d9bd80ec5 Add QCA vendor attributes to configure global TX chain mask
f5b8ef6c966a Add QCA vendor attributes for MSDU TX statistics
6c11fcefe4fc hostapd: Prevent blocking sends on control interface monitor socket
0bbb8a66f64c AP MLD: Remove redundant outer loop in hostapd_notif_disassoc_mld()
52fb5ccd91f3 AP MLD: Avoid using mld_id to identify partners
7bb930d50b5f wpa_supplicant: Add option to disable 80+80 MHz opclass advertisement
9001059bd6ad tests: Make dbus_connect_oom more robust
663fb1940231 AP MLD: Fix hostapd_is_mld_ap() check
590f3bdb4c61 AP MLD: Rename hostapd_is_mld_ap() to hostapd_is_multiple_link_mld()
b13b69a235f7 Add VLANID in the AP-STA-CONNECTED events
c1e8b1c6462b SAE: Assign VLAN when using PMKSA caching
9bc29dcdfdee SAE: Default password binding through control interface
9de127c31c40 tests: More testing coverage for SAE with multiple passwords
5ce1d4180386 nl80211: Fix crash by cancelling scan timeout before a BSS is removed
ca266cc24d87 nl80211: Fix crash by setting the drv->ctx properly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This commit fixes "aff2f096235 include: make APK .list files reproducible"
since it would create the .list file while `find` still runs. This causes the
.list file to be part of itself. As an alternative, write the file to a
temporary folder first and then move it.
Fix: aff2f09623 include: make APK .list files reproducible
Signed-off-by: Paul Spooren <mail@aparcar.org>
LLDP packets must be transmitted on a single port and trapped on a port of
a device which understands LLDP. It must not forward it to other ports to
avoid confusing neighbor information on connected devices.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19571
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Driver needs to configure management frame actions
To support LLDP, EAPOL or MSTP, which needs to be trapped to the CPU
instead of being forwarded.
The function to implement the various management frame actions was already
present but not yet registered correctly.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19571
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Driver needs to configure management frame actions
To support LLDP, EAPOL or MSTP, which needs to be trapped to the CPU
instead of being forwarded
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19571
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The functions to enable trapping of management frames are not RTL83xx
specific. It is more appropriate to use the more generic "rtldsa" prefix
for them.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19571
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add new option required to build with VHOST_MENU=y
This option enables two IOCTLs: VHOST_SET_FORK_FROM_OWNER and
VHOST_GET_FORK_FROM_OWNER. These allow userspace applications
to modify the vhost worker mode for vhost devices.
Also expose module parameter 'fork_from_owner_default' to allow users
to configure the default mode for vhost workers.
By default, `VHOST_ENABLE_FORK_OWNER_CONTROL` is set to `y`,
users can change the worker thread mode as needed.
If this config is disabled (n),the related IOCTLs and parameters will
be unavailable.
If unsure, say "Y".
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19618
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18904
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use macro defined bias types instead of some magic numbers. This can
help reviewers better understand bias types.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19855
Signed-off-by: Robert Marko <robimarko@gmail.com>
wmcpu_emi node was removed in commit:
b286fd8a39 ("uboot-mediatek: adjust the reserved memory regions")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19855
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RTL931x has 14 frontend and at least 26 backend serdes. Currently
the programming functions always need to determine the right backend
serdes from the given frontend serdes on their own.
We plan to provide a consistent serdes mapping to all callers as follows
Frontend SerDes | 0 1 2 3 4 5 6 7 8 9 10 11 12 13
-----------------+------------------------------------------
Backend SerDes 1 | 0 1 2 3 6 7 10 11 14 15 18 19 22 23
Backend SerDes 2 | 0 1 2 4 6 8 10 12 14 16 18 20 22 24
Backend SerDes 3 | 0 1 2 5 6 9 10 13 14 17 18 21 22 25
frontend page "even" frontend SerDes "odd" frontend SerDes
page 0x000-0x03f (analog): page 0x000-0x03f back SDS page 0x000-0x03f back SDS
page 0x100-0x13f (XSGMII1): page 0x000-0x03f back SDS page 0x000-0x03f back SDS+1
page 0x200-0x23f (XSGMII2): page 0x000-0x03f back SDS page 0x000-0x03f back SDS+2
As a first micro step provide some helpers that simply operate on
frontend serdes and will determine the backend serdes on their own.
So rtmdio_931x_read_sds_phy() and rtmdio_931x_write_sds_phy() operate
on backend serdes. While rtmdio_931x_read_sds_phy_**new**() and
rtmdio_931x_write_sds_phy_**new**() operate on frontend serdes.
This is only an intermediate naming convention and will be cleanup
afterwards.
In a first step make use of these new functions whenever we
want to access the analog page. As the pages stay unchanged
in the new functions conversion is as simple as this:
Old:
asds = rtl931x_get_analog_sds(...)
rtmdio_931x_read_sds_phy(asds, ...)
New:
rtmdio_931x_read_sds_phy_new(sds, ...)
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19818
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k documentation says to use pci168c strings for the compatible
string, probably because the OWL loader uses it to overide bogus pci IDs
like abcd. This is not the case with ath10k and the documentation
explicitly states to use qcom,ath10k.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18920
Signed-off-by: Robert Marko <robimarko@gmail.com>
This device does not come with a pci card. It has a slot where one can
get supplied. What's more, nvmem or ieee80211 frequency limits are not
applied here. It can just get removed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18920
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18906
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18908
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
Set the pcie device to qcom,ath10k as the Documentation says, The pci
line implies it's ath9k when it's actually ath10k.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18873
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18873
Signed-off-by: Robert Marko <robimarko@gmail.com>
The kmod is installed on all filogic mediatek images, even for devices
that do not have any aquantia hardware. Remove it.
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19488
[Do not explicitly remove kmod-phy-aquantia from gatonetworks_gdsp]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NILFS is a log-structured file system developed for Linux.
NILFS provides versioning capability of an entire file system
and continuous snapshotting that allows users to restore files
mistakenly overwritten or destroyed a while ago.
Signed-off-by: Pavlo Samko <bulldozerbsg@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18247
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NILFS is a log-structured file system developed for Linux.
NILFS provides versioning capability of an entire file system
and continuous snapshotting that allows users to restore files
mistakenly overwritten or destroyed a while ago.
Signed-off-by: Pavlo Samko <bulldozerbsg@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18247
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move append-teltonika-metadata to image-commands.mk and unify over different targets.
This method can be used to create valid "factory" images for most of Teltonika devices.
Signed-off-by: Simonas Tamošaitis <simsasss@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19401
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Zoltan HERPAI wigyori@uid0.hu
Link: https://github.com/openwrt/openwrt/pull/18907
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Support in mt76 has existed for quite a while. Use it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19799
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for the WAVLINK WL-WN586X3 Rev B, which swaps
the 16MB NOR flash for an 128MB NAND flash chip, and uses UBI for
data partition. This commit utilizes the previous submitted dtsi that
includes common hardware for a few Wavlink routers.
Hardware
--------
- SOC: MediaTek MT7981B
- RAM: 256MB DDR3
- Flash: 128MB SPI-NAND (ESMT F50L1G41LB)
- Ethernet: 2x1Gb Lan 1x1Gb Wan
- WiFi: MediaTek MT7981B 2x2 DBDC 802.11ax 2T2R (2.4/5) with 4 external and 1 internal antennae
- LEDs: 2xLan 1x Wan 1x WIFI 1xSTATUS
Installation
------------
Flashing over the vendor WebUI has been tested and unsuccessful (YMMV).
The image need to be flashed via TFTP which can be activated over the onboard UART serial console:
1. Connect UART: TX->board RX, RX->board TX, GND->board GND.
2. Connect PC to router lan port.
3. Setup the tftp server on PC, set IP to 192.168.10.100.
4. Power on the device. Interrupt boot countdown at uboot boot menu and select 2. Upgrade firmware option.
5. Input the image name and start flashing.
Sample uboot menu:
```
*** U-Boot Boot Menu ***
1. Startup system (Default)
2. Upgrade firmware
3. Upgrade ATF BL2
4. Upgrade ATF FIP
5. Upgrade single image
6. Load image
0. U-Boot console
```
NOTE: Do not use the intermediate image here which is for Rev A only:
https://github.com/themaverickdm/firmware-misc/tree/main/wavlink/wl-wn586x3
MAC Addresses
-------------
LAN: 80:3F:5D:xx:xx:x1 (hw, 0x44e, ASCII encoded)
WAN: 80:3F:5D:xx:xx:x2 (hw, 0x460, ASCII encoded)
2G: 80:3F:5D:xx:xx:x3 (factory, 0x4, raw binary, also on label)
5G: 80:3F:5D:xx:xx:x3 (Same as 2G)
Signed-off-by: Zhenfu Shi <i0ntempest@i0ntempest.com>
Link: https://github.com/openwrt/openwrt/pull/19785
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CREALITY BOX WB01 is small footprint router based on MediaTek MT7688,
is a device intended to interface Creality brand 3D printers to a cloud service.
Specifications:
- SoC: MediaTek MT7688AN @ 580MHz
- RAM: DDR2 128M (Winbond W971GG6SB-25)
- Flash: BoyaMicro BY25Q128AS (16 MiB, SPI NOR) handled by BoHong bh25q128as driver
- WiFi: 2.4GHz 1T1R internal panel antenna
- Ethernet: 1x LAN (10/100)
- USB: 2x USB2.0 port (Genesys Logic GL850G 2 port USB 2.0 hub)
- UART: 3.3V, TX, RX, GND / 56700 8N1 / only pads on PCB
- microSD SD-XC Class 10 slot
- micro USB input (for power only)
- reset button
- FCC ID: 2AXH6CREALITY-BOX
MAC addresses as verified by OEM firmware:
vendor OpenWrt source
LAN eth0 factory 0x2e
2.4GHz phy0-ap0 factory 0x04 (label)
LEDs
color vendor OpenWRT configurable
red SD card activity - yes
green Cloud connectivity status yes
blue LAN activity eth0 yes
yellow WIFI activity phy0tpt yes
Return to OEM & debrick
- download "cxsw_update.tar.bz2" from manufacturer site
- extract archive to FAT32 USB stick root
- put USB stick in USB2 port
- press & hold reset button
- power on device while holding reset
- wait approx 10 sec
- release reset button
Installation with SD Card
- power on device
- wait for device to finish starting
- copy "openwrt-ramips-mt76x8-creality_wb-01-squashfs-cxsw_update.tar.bz2"
to root of FAT32 SD card
- rename openwrt-ramips-mt76x8-creality_wb-01-squashfs-cxsw_update.tar.bz2
to "cxsw_update.tar.bz2"
- put SD card in device
- device will install OpenWRT on internal flash
Installation via telnet:
- extract the "factory.bin" and "install.sh" from newly created
openwrt-ramips-mt76x8-creality_wb-01-squashfs-cxsw_update.tar.bz2
to FAT32 USB stick root
- telnet to 10.10.10.254, user: root, password: cxswprin
- plug the USB in USB1 port
- cd /media/usbdisk/
- sh install.sh
- device will write "factory.bin" to internal flash
Co-authored-by: George Brooke <figgyc@figgyc.uk>
Co-authored-by: Peca Nesovanovic <peca.nesovanovic@sattrakt.com>
Co-authored-by: shivajiva101 <github.com/shivajiva101>
Co-authored-by: Axel Sepulveda <ansepulveda@uc.cl>
Signed-off-by: Axel Sepulveda <ansepulveda@uc.cl>
Link: https://github.com/openwrt/openwrt/pull/19686
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
mt7531 switch reset delay time is hard coded in the driver. The
"reset-assert-us" and "reset-deassert-us" won't take effect.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19741
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* Increase mt7986 ATF reserved memory to 256 kiB to follow the linux
kernel and Trusted Firmware-A changes.
* Remove unnecessary reserved memory region for the WiFi hardware. The
u-boot can not drive the WiFi hardware. Hence we don't need to keep
this memory region.
* Remove useless node labels and update comments.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19741
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
