Update default kernel version to 6.12 and drop configs and patches for
kernel 6.6.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/19666
Signed-off-by: Nick Hainke <vincent@systemli.org>
Like RTL839x the RTL930x SoCs have multithreading built in.
Activate it in the kernel configuration.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19624
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RTL839x mdio functions are scattered around the code. Relocate
them to the bus (still inside the ethernet driver).
Additionally provide a consistent SerDes register access through the
mdio bus. Until now when a SerDes directly drives a SFP module there
is no clear rule of how to handle its register set that consists of
two parts:
- c22 phy registers 0-15 live in the fiber page (2) of the SerDes
- other SerDes specific registers exist in pages before and after
The mdio bus and other SerDes functions are a wild mix of directly
looking into page 2 or just using self defined methods to access
data.
Adapt the bus to the new consistent phy interface that mixes the
SerDes register set like classic Realtek phys do it.
- Use register 31 as page select (already in the bus)
- Always keep the common registers 0-15 in place and read fiber page
- Map the SerDes internal registers into the upper vendor specific
registers 16-23 according to the page select register (31).
That gives a register mapping as follows:
+-----------------------+-----------------------+---------------+-------------+
| reg 0x00-0x0f | reg 0x10-0x17 | reg 0x18-0x1e | reg 0x1f |
+-----------------------+-----------------------+---------------+-------------+
| SerDes fiber page (3) | real SerDes registers | zero | SerDes page |
| registers 0 - 15 | in packages of 8 | | select reg |
+-----------------------+-----------------------+---------------+-------------+
Example to make it as clear as possible.
SerDes registers on a RTL839x show
Page / Reg | 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B ...
-------------+----------------------------------------------------------------
0 - SDS | 0C03 0F00 7060 7106 074D 0EBF 0F0F 0359 5248 0000 0F80 0000 ...
1 - SDS_EXT | 0000 0000 85FA 8C6D 5CCC 0000 20D8 0003 79AA 8C64 00C3 1482 ...
2 - FIB | 1140 6189 001C CA40 01A0 0000 0000 0004 0000 0000 0000 0000 ...
3 - FIB_EXT | 1140 6109 001C CA40 01A0 0000 0000 0004 0000 0000 0000 0000 ...
This translates to this phy layout
| SerDes fiber registers normal SerDes registers zero p.sel
Page / Reg | 0x00 0x01 0x02 0x03 ... 0x10 0x11 0x12 0x13 ... 0x18 ... 0x1f
-------------+---------------------------------------------------------------
0 | 1140 6189 001C CA40 ... 0C03 0F00 7060 7106 ... 0000 ... 0000
1 | 1140 6189 001C CA40 ... 5248 0000 0F80 0000 ... 0000 ... 0001
...
4 | 1140 6189 001C CA40 ... 0000 0000 85FA 8C6D ... 0000 ... 0004
...
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19634
Signed-off-by: Robert Marko <robimarko@gmail.com>
* Use SDS for phy 48/49
* Use correct link/phy settings for SFP ports
* Remove read-only flag from u-boot env so fw_setenv actually works
Signed-off-by: Joe Holden <jwh@zorins.us>
Link: https://github.com/openwrt/openwrt/pull/19596
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When a SerDes directly drives a SFP module there is no clear rule of
how to handle its register set that consists of two parts:
- c22 phy registers 0-15 live in the fiber page (2) of the SerDes
- other SerDes specific registers exist in pages before and after
The mdio bus and other SerDes functions are a wild mix of directly
looking into page 2 or just using self defined methods to access
data.
Provide a consistent phy interface that mixes the SerDes register
set like classic Realtek phys do it.
- Use register 31 as page select (already in the bus)
- Always keep the common registers 0-15 in place and read fiber page
- Map the SerDes internal registers into the upper vendor specific
registers 16-23 according to the page select register (31).
That gives a register mapping as follows:
+-----------------------+-----------------------+---------------+-------------+
| reg 0x00-0x0f | reg 0x10-0x17 | reg 0x18-0x1e | reg 0x1f |
+-----------------------+-----------------------+---------------+-------------+
| SerDes fiber page (3) | real SerDes registers | zero | SerDes page |
| registers 0 - 15 | in packages of 8 | | select reg |
+-----------------------+-----------------------+---------------+-------------+
Example to make it as clear as possible.
SerDes registers on a RTL838x show
Page / Reg | 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B ...
-------------+----------------------------------------------------------------
0 - SDS | 0C03 0F00 7060 7106 074D 0EBF 0F0F 0359 5248 0000 0F80 0000 ...
1 - SDS_EXT | 0000 0000 85FA 8C6D 5CCC 0000 20D8 0003 79AA 8C64 00C3 1482 ...
2 - FIB | 1140 6189 001C CA40 01A0 0000 0000 0004 0000 0000 0000 0000 ...
3 - FIB_EXT | 1140 6109 001C CA40 01A0 0000 0000 0004 0000 0000 0000 0000 ...
This translates to this phy layout
| SerDes fiber registers normal SerDes registers zero p.sel
Page / Reg | 0x00 0x01 0x02 0x03 ... 0x10 0x11 0x12 0x13 ... 0x18 ... 0x1f
-------------+---------------------------------------------------------------
0 | 1140 6189 001C CA40 ... 0C03 0F00 7060 7106 ... 0000 ... 0000
1 | 1140 6189 001C CA40 ... 5248 0000 0F80 0000 ... 0000 ... 0001
...
4 | 1140 6189 001C CA40 ... 0000 0000 85FA 8C6D ... 0000 ... 0004
For now just do it for RTL838x devices.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19604
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is a variant of the Radxa ROCK Pi E v3 equipped with the Realtek
RTL8821CU. Add the kmod-rtw88-8821cu package for it.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/18310
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The DSA has a link to the MDIO bus and already uses the read/write functions
that are provided. In parallel the dsa_switch_ops structure provides an
interface for phy_read and phy_write. These are still open-coded and sadly
circumvent the bus. Simplify the implementation and avoid inconsistencies by
reusing the existing bus infrastructure.
Additionally, remove two unused MMD header definitions as a quick win.
Reported-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19548
Signed-off-by: Robert Marko <robimarko@gmail.com>
The function rtl93xx_setup() is called by both RTL930x and RTL931x. But
only the RTL930x specific function to print port matrix was called.
Unfortuntaly, RTL931x needs a different function to access the correct
registers to retrieve the port matrix information.
It is therefore necessary differentiate in rtl93xx_setup between the
SoC families before calling the appropriate function.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19572
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RTL931x has 56 (0-55) non-CPU ports. To receive updates about the port
state, it is therefore necessary to enable the interrupts for all these
ports.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19572
Signed-off-by: Robert Marko <robimarko@gmail.com>
* traffic isolation tables are different between rtl930x and rtl931x
* traffic_enable/disable/get/set functions span multiple columns in the
rtl931x as a result, previous implementation would only enable traffic
in some ports.
traffic_enable/disable and traffic_set/get should now work on all ports and
not just the initial 32
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19572
Signed-off-by: Robert Marko <robimarko@gmail.com>
A commit which broke netdev trigger LEDs offloaded to PHYs recently made
it all the way down to the Linux 6.6 stable branch. The revert has been
accepted to linux-next, however, a backport to the various -stable trees
is still pending.
Import the backported revert commit to fix in OpenWrt in the meantime
until the revert also gets picked to linux-stable.
Link: https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=26f732791f2bcab18f59c61915bbe35225f30136
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Deleted useless content, since it is the same as the mainline kernel
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19300
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove extra blank lines.
Fixes typo for label and status.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/19400
Signed-off-by: Robert Marko <robimarko@gmail.com>
Include the NAND specs into the DTS. It is unclear which devices
really need it. Keep it disabled for now. As the SoC register area
is defined too small until now, increase the size to an appropriate
value.
If enabled one can see the following log messages (e.g. Linksys
LGS328C or LGS352C).
[ 1.206600] spi-nand spi1.0: Macronix SPI NAND was found.
[ 1.212795] spi-nand spi1.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[ 1.222217] 3 fixed-partitions partitions found on MTD device spi1.0
[ 1.229466] OF: Bad cell count for /soc/spi@1a400/flash@0/partitions
[ 1.236617] OF: Bad cell count for /soc/spi@1a400/flash@0/partitions
[ 1.244164] Creating 3 MTD partitions on "spi1.0":
[ 1.249620] 0x000000000000-0x000004000000 : "ubifs"
[ 1.423593] 0x000004000000-0x000005e00000 : "firmware"
[ 1.738268] mtdsplit_uimage: no uImage found in "firmware"
[ 1.744577] 0x000005e00000-0x000007c00000 : "runtime2"
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19583
Signed-off-by: Robert Marko <robimarko@gmail.com>
RTL93xx devices have a NAND controller built in. Upstream already
has a driver in place. Include it downstream. Activate it in the
RTL93xx builds and disable it for the RTL83xx builds.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19583
Signed-off-by: Robert Marko <robimarko@gmail.com>
During PHY matching, the SMI polling must be disabled to avoid conflicts
during the complex detection routine. Only after this finished, SMI polling
is allowed again.
This was implemented for all realtek families besides RTL931x.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19603
Signed-off-by: Robert Marko <robimarko@gmail.com>
A RTL930x function to read the value from an SDS register must not used on
an RTL931x SoC. Doing it with rtl930x_read_sds_phy() would corrupt the
written results when only parts of the bits are written.
Fixes: 7026084066 ("realtek: Add SDS configuration routines for the RTL93XX platforms")
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19603
Signed-off-by: Robert Marko <robimarko@gmail.com>
Vimin VM-S100-0800MS is an 8 port Multi-Gig switch, based on RTL9303.
Ported from XikeStor SKS8300-8X with changes to support different u-boot
build.
Specification:
- SoC : Realtek RTL9303
- RAM : DDR3 512 MiB
- Flash : SPI-NOR 16 MiB (Winbond W25Q128JVSQ)
- Ethernet : 8x 1/2.5/10 Gbps (SFP+)
- LEDs/Keys (GPIO): 0x/1x
- UART : "Console" port on the front panel
- type : RS-232C
- connector : RJ-45
- settings : 115200n8
- Power : AC100-240V 50/60Hz
Flash instruction using initramfs image:
1. Prepare TFTP server with an IP address "192.168.1.111"
2. Connect your PC to Port1 on VM-S100-0800MS
3. Power on VM-S100-0800MS and interrupt boot by pressing Esc
4. Enable Port1 with the following commands
rtk 10g 0 fiber1g (or fiber10g if 10GBase-*R, dac300cm for DAC cable)
rtk ext-devInit 0
rtk ext-pinSet 2 0
Note: the last command sets tx-disable to low
7. Download initramfs image from TFTP server
tftpboot 0x82000000 <image name>
8. Boot with the downloaded image
bootm
9. On the initramfs image, backup the stock firmware if needed
10. Upload (or download) sysupgrade image to the device
11. Erase "firmware" partition to cleanup JFFS2 of stock FW
mtd erase firmware
12. Perform sysupgrade with the sysupgrade image
13. Wait ~120 sec to complete flashing
Reverting to stock firmware:
1. Prepare by downloading the stock firmware. Vimin doesn't have
the firmware on their website, tested using firmware for shared
hardware Nicgiga S100-0800S-M.
Filename: vmlinux-nicgiga-S100-0800S-M-241126EN.bix
2. Prepare TFTP server with an IP address "192.168.1.111"
3. Connect your PC to Port1 on VM-S100-0800MS
4. Power on VM-S100-0800MS and interrupt boot by pressing Esc
5. Enable Port1 with the following commands
rtk 10g 0 fiber1g (or fiber10g if 10GBase-*R, dac300cm for DAC cable)
rtk ext-devInit 0
rtk ext-pinSet 2 0
Note: the last command sets tx-disable to low
6. Download initramfs image from TFTP server
tftpboot 0x82000000 <image name>
7. Boot with the downloaded image
bootm
8. Under Management -> Firmware -> Upgrade/Backup, upload bix file.
9. Reboot device
Signed-off-by: Colton Pawielski <cepawiel@mtu.edu>
Link: https://github.com/openwrt/openwrt/pull/19477
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The tsens node had an extra space in the "okay" status string, preventing
thermal sensors from being properly registered. This patch corrects it to
enable proper thermal monitoring support.
Signed-off-by: Shubham Vishwakarma <shubhamvis98@fossfrog.in>
Link: https://github.com/openwrt/openwrt/pull/19564
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for Hasivo S1100W-8XGT-SE switch.
Device specification
--------------------
SoC Type: RTL9303
RAM: Samsung K4B461646E-BYKO (512MB)
Flash: Fudan FM25Q128A (16 MB)
Ethernet: 8x 10G via 2x RTL8264 PHY
LEDs: 2 LEDs, 1 power green, 1 system green
Button: Reset
USB ports: None
Bootloader: Realtek U-Boot - U-Boot 2011.12.(3.6.6.55087) (Nov 13 2022 - 14:37:31)
Fan: 2 fans controlled by STC8G1K08 TSOP-20 microcontroller
Note: The fan appears to operate the same irrespective of the running
firmware. The STC9G1K08 is likely operating independently.
To explore the stock vendor firmware, there are 2 avenues to gain root
access. This is not necessary to install OpenWrt, but is here for
reference.
Root access via serial
----------------------
1. ctrl+t
2. password: switchrtk
3. press 's' for shell
Root access via SSH
-------------------
1. ctrl+t
2. password: switchrtk
3. sys command sh
4. log in with your username+password
5. ctrl+t
6. password: switchrtk
7. press 's' for shell
Credit to https://forum.openwrt.org/t/hasivo-switches/151758/174 for rooting instructions.
Installing OpenWrt
------------------
1. Connect to UART. UART requires soldering an RJ45 connector to the
console footprint on the board. The header is on the top right of
this image: 4d2ab97fad.jpeg
2. Set computer IP to 192.168.0.111.
3. Enter bootloader by pressing esc key during boot.
4. Enter password 'Hs2021cfgmg'.
5. Type 'XXXX'.
6. setenv bootcmd 'rtk network on; bootm 0xb4300000'
7. saveenv
8. rtk network on
9. tftpboot 0x84f00000 <openwrt-initramfs>
10. bootm 0x84f00000
Now you can copy over the sysupgrade image and install.
Credit to
https://forum.openwrt.org/t/hasivo-switches/151758/22?u=andrewjlamarche
for u-boot console access instructions.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17137
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since Linux 6.7, introduced with commit 5c2f7727d437 ("mtd: mtdpart:
check for subpartitions parsing result"), errors during subpartition
parsing cause all MTD partitions to be torn down.
Since the current mtdsplit driver for devices using H3C VFS returns
-EINVAL if it does not find a file system containing an OpenWrt image,
this makes initial installation of OpenWrt impossible.
Work around this by returning 0 when the file system contains unexpected
data. Also print a message in this case to show what is going on.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19475
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adds the capability to flash the factory image using the OEM recovery
software, ipTIME Firmware Wizard(11ac).
Installation
------------
1. Download the OEM recovery software from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router(keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router(LAN port) to the PC
6. Run the OEM recovery software and follow the instructions
7. Select the *squashfs-factory.bin file during the router recovery process
8. Wait for the router to boot from *squashfs-factory.bin
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19497
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Maintain 64 bit counters by polling the hardware counters and adding up
the differences. Polling needs to happen just often enough to catch
every single overflow.
As we now have non-overflowing counters now, we can safely calculate
composite counters without getting weird results on overflow. Use this
to follow RFC 3635 more accurately by mapping the hardware counters to
the proper counters, while taking into account hardware quirks as best
as possible.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/18415
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
By default, the network interface stats are based on software counters,
which only consider traffic from and to the CPU. Implementing the
get_stats64 method allows to report the full hardware counters instead.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/18415
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kernel offers several alternatives to get_ethtool_stats which allow
to report some stats in a more structured way. Use them where possible.
Ideally, we should follow RFC 3635 to translate the hardware counters to
the supported frame and octet counters. However, this is not feasible,
as some of the counters are 32-bit only (so it would produce incorrect
results as soon as one of them overflows).
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/18415
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The MIB registers contain different stats depending on the SoC, and for
RTL930x some stats are in an additional register.
Create separate MIB descs for each SoC to implement this. Also make
reading 64-bit counters more robust, by protecting against an overflow
of the lower 32 bits during the read.
RTL931x remains unsupported, because it uses a table and thus requires
a separate implementation.
While we are at it, rename structs/functions to use the rtldsa prefix.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/18415
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
kmod-md-multipath was removed in kernel 6.12, remove the dependency here
too.
This fixes the build of the gemini target.
Fixes: d12a603de5 ("kernel: kmod-md-multipath: Depend on kernel 6.6")
Link: https://github.com/openwrt/openwrt/pull/19532
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
After observation that timer interrupt 7 always fires on secondary VPEs
the counter was disabled in the startup code. This is a bad idea when
building the kernel with jitterentropy. To generate entropy it makes use
of function random_get_entropy(). On MIPS architecture this simply reads
the counter register on the current core. With a disabled counter it
always returns the same value and the entropy initialization stalls the
core if it runs on a secondary VPE. See backtrace
[ 21.736246] rcu: INFO: rcu_sched self-detected stall on CPU
[ 21.736246] rcu: INFO: rcu_sched self-detected stall on CPU
[ 21.748594] rcu: 1-....: (2100 ticks this GP) idle=064c/1/0x40000002 softirq=7/7 fqs=1050
[ 21.748594] rcu: 1-....: (2100 ticks this GP) idle=064c/1/0x40000002 softirq=7/7 fqs=1050
[ 21.766871] rcu: (t=2102 jiffies g=-1187 q=25 ncpus=2)
[ 21.766871] rcu: (t=2102 jiffies g=-1187 q=25 ncpus=2)
[ 21.778429] CPU: 1 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.12.39 #482
[ 21.778429] CPU: 1 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.12.39 #482
[ 21.778461] Hardware name: Zyxel GS1900-48
[ 21.778461] Hardware name: Zyxel GS1900-48
...
[ 21.779757] [<8029b968>] jent_measure_jitter+0xc8/0x10c
[ 21.779757] [<8029b968>] jent_measure_jitter+0xc8/0x10c
[ 21.779779] [<8029b9e8>] jent_gen_entropy+0x3c/0xb0
[ 21.779779] [<8029b9e8>] jent_gen_entropy+0x3c/0xb0
[ 21.779800] [<8029bcc0>] jent_entropy_collector_alloc+0x104/0x118
[ 21.779800] [<8029bcc0>] jent_entropy_collector_alloc+0x104/0x118
[ 21.779822] [<8029bd6c>] jent_entropy_init+0x4c/0x2ec
[ 21.779822] [<8029bd6c>] jent_entropy_init+0x4c/0x2ec
[ 21.779844] [<8086f184>] jent_mod_init+0x58/0xac
[ 21.779844] [<8086f184>] jent_mod_init+0x58/0xac
[ 21.779865] [<80100200>] do_one_initcall+0x70/0x250
[ 21.779865] [<80100200>] do_one_initcall+0x70/0x250
[ 21.779883] [<8085c018>] kernel_init_freeable+0x1f0/0x280
[ 21.779883] [<8085c018>] kernel_init_freeable+0x1f0/0x280
[ 21.779905] [<8067cba4>] kernel_init+0x20/0xb0
[ 21.779905] [<8067cba4>] kernel_init+0x20/0xb0
[ 21.779926] [<80101158>] ret_from_kernel_thread+0x14/0x1c
[ 21.779926] [<80101158>] ret_from_kernel_thread+0x14/0x1c
This bit of entropy is helpful on these low end devices. Reenable the
counter and simply disable the interrupt.
Fixes: b7aab19585 ("realtek: SMP handling of R4K timer interrupts")
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19499
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The mdio bus functions are still split between ethernet and dsa driver.
Before moving everthing out to a separate mdio driver we decided to
collect everything in the ethernet driver with the rtmdio prefix.
Take over the remaining RTL838x functions.
Remark: This is more or less a copy/paste with function renaming. As
there are still some consumers in the DSA driver the definitions and
inclusions must be flipped.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19484
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently the SerDes driven SFP ports give strange ethtool readings
on RTL83xx devices. Especially duplex and speed are shown even if
no link is up and running. That leads to confusion because the MAC
reports arbitrary values.
Enhance the readout by refactoring the pcs_get_state() function.
Calculate speed/duplex/pause only if link is detected. Additionally
add reporting of 10G for SFP+ on RTL839x.
ethtool for empty SFP cage before/after
root@OpenWrt:~# ethtool lan9
Settings for lan9:
Supported ports: [ MII ]
Supported link modes: 1000baseT/Full
1000baseKX/Full
1000baseX/Full
1000baseT1/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 1000baseT/Full
1000baseKX/Full
1000baseX/Full
1000baseT1/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: 10Mb/s
Duplex: Half
Port: MII
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Link detected: no
root@OpenWrt:~# ethtool lan9
Settings for lan9:
Supported ports: [ MII ]
Supported link modes: 1000baseT/Full
1000baseKX/Full
1000baseX/Full
1000baseT1/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 1000baseT/Full
1000baseKX/Full
1000baseX/Full
1000baseT1/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Unknown! (255)
Port: MII
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Link detected: no
ethtool with inserted but NOT connected 1G module before/after
root@OpenWrt:~# ethtool lan9
Settings for lan9:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 1000baseX/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Link detected: no
root@OpenWrt:~# ethtool lan9
Settings for lan9:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 1000baseX/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Unknown! (255)
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Link detected: no
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19524
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows building the kmod-drm-ivpu which depends on
CONFIG_DRM_ACCEL. This module is x86_64 only.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kmod-rpi-panel-attiny-regulator and kmod-rpi-panel-7inch-touchscreen
are included in target modules.mk file, they should also depend on the target,
otherwise they can be selected from every target.
Fix the AutoProbe for panel-raspberrypi-touchscreen too.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kmod-imx2-wdt, kmod-imx7-ulp-wdt and kmod-wdt-sp805 are included in
target modules.mk file, they should also depend on the target, otherwise
they can be selected from every target.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kmod-ata-dwc is included in target modules.mk file, it should also
depend on the target, otherwise it can be selected from every target.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_BCMGENET kernel config option will select this driver. Add
the driver to the kernel config menu and make kmod-bcmgenet depend on
it.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The SerDes setup function needs to be called to make 2500Base-X work.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19517
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On some devices (like ZyXEL GS1920) the phys are not initialized and patched
by the bootloader. This is done through the vendor SDK when the software
starts. To make these devices usable too, provide the most basic setup
sequence for the RTL8218B.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19491
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The driver currently uses two checks to verify the capabilities. These
are ..._phylink_get_caps() and ..._pcs_validate(). For RTL930x these
must allow 2.5G modes. Enhance that as follows:
Add 2500BASEX to phylink_get_caps(). Sort the interfaces alphabetically
and rename the function to the new prefix. IMPORTANT REMARK! Until now
this function allowed the XGMII mode (10G only parallel interface) that
was somehow mixed with the Realtek proprietary mode XSGMII (10G SGMII).
Remove it to avoid further confusion.
Looking upstream pcs_validate() is used less and less. There are only
2 consumers left in 6.16 and the calling location reads:
/* Validate the link parameters with the PCS */
if (pcs->ops->pcs_validate) {
ret = pcs->ops->pcs_validate(pcs, supported, state);
if (ret < 0 || phylink_is_empty_linkmode(supported))
return -EINVAL;
/* Ensure the advertising mask is a subset of the
* supported mask.
*/
linkmode_and(state->advertising, state->advertising,
supported);
}
There is no need for this additional check. Drop the functions.
Tested-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19429
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This file should be generated automatically at runtime by the kernel
build system.
Link: https://github.com/openwrt/openwrt/pull/19473
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
