Fix probing and load correct drivers
when using last backports.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19927
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the NPU and reserved memory node for AN7581 dtsi since it's not
supported.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Major backport of upstream patch for support of multiple feature of the
Airoha Ethernet driver.
Feature backported are TSO, Jumbo packet, Offload and initial Wlan
Offload support.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport trivial fixes from upstream related to pinctrl and ethernet
driver.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport patch adding support for AN7581 Ethernet PHY based on the same
Mediatek embedded Switch PHY.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Mediatek PHY patch has been merged upstream. Reintroduce them to
backport directory as the same PHY is also needed for Airoha target.
All the affected patch automatically refreshed.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add support for Airoha EN7581 NPU firmware present in linux-firmware.
Support for it is fully upstream with the Ethernet part fully pushed and
the Wireless Offload currently in progress for various WiFi chip.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport support for Aeonsemi AS121xxx PHY. The PHY require dedicated
firmware to be loaded to correctly work and support a big family of
Aeonsemi PHY that provide from 1G to 10G speed.
Automatically refresh all affected patch and file (rtl PHY).
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add support for Aeonsemi AS21xxx firmware blob. Firmware has been
submitted and accepted to linux-firmware. Current version is 1.8.2.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace thermal patch with upstream version. The thermal maintainer
reported that the sysfs entry are considered deprecated and that slope
and offset should be handled internally to the driver.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix the model name in DTS compatible, Makefiles and board scripts by
using dash instead of comma or underscore. This aligns it with other
examples in OpenWrt and makes in consistent in all places where the
board model is used.
'tplink,tl-st1008f,v2' --> 'tplink,tl-st1008f-v2'
'tplink,tl-st1008f_v2' --> 'tplink,tl-st1008f-v2'
Fixes: 39b9b491bb ("realtek: add support for TP-Link TL-ST1008F v2.0")
Fixes: #19930
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19934
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport a patch from upstream kernel 6.17-rc4 which fixes a regression
introduced in the latest stable kernel versions.
This is already in the Linus stable queues for the next minor kernel
updates.
Fixes: 1c92e468d5 ("kernel: bump 6.6 to 6.6.103")
Fixes: f39c7e103f ("kernel: bump 6.12 to 6.12.43")
Reported-by: Goetz Goerisch <ggoerisch@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently it is printed as "null" (including quotes). Display it the same
as old iwinfo as unknown (no quotes).
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
When creating the PSK file, the old script sets `mac` to
`00:00:00:00:00:00` when `mac` is not specified (see [here][1]),
creating hostapd configuration lines like:
vlanid=10 00:00:00:00:00:00 MyStrongPassword
That matches any MAC address (a wildcard). The `ucode` script alternative
misses the default, so set it.
[1]: 9c26d14489/package/network/config/wifi-scripts/files/lib/netifd/hostapd.sh (L428)
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Currently the calculation for the CMU (even) SerDes works similar
to this pseudo code.
analog_backend_serdes = get_analog_serdes(frontend_serdes);
even_backend_serdes = analog_backend_serdes & ~1;
write_to(even_backend_serdes);
Because of the SerDes layout and frontend/backend mapping this can
be swapped to the following order with the same resulting Serdes.
even_frontend_serdes = frontend_serdes ~1;
analog_backend_serdes = get_analog_serdes(even_frontend_serdes);
write_to(analog_backed_serdes);
In the later example the frontend/backend mapping code is already
in our new functions. So swap the calculation logic and use the
new access functions. This allows to finally drop the old access
functions without mapping.
From now on all RTL931x SerDes functions will use a consistent
frontend view.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19873
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The RTL931x has 14 frontend and at least 26 backend serdes. Currently
the programming functions always need to determine the right backend
serdes from the given frontend serdes on their own. We plan to provide
a consistent serdes mapping to all callers.
As the third step make use of these new functions whenever we want to
access the "digital 2" pages. The pages are mapped starting at 0x200.
So the function conversion is as simple as this:
Old:
dsds = (sds - 1) * 2;
rtmdio_931x_read_sds_phy(dsds + 1, page, ...)
New:
rtmdio_931x_read_sds_phy_new(sds, page + 0x200, ...)
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19873
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The more we step down into the SerDes deeps the more confusing it
gets. Nevertheless it is not to late to fix a wrong assumption.
Until now it seemed as if the frontend/backend SerDes mapping is
totally without intersection. This is not true.
The backend SerDes mapping is also dependent on the mode. Especially
the proprietary Realtek XSGMII mode stands out from all other
mappings. So fix the descriptions and the calculation of the third
page package (digital 2 aka XSGMII 2).
As it was not yet used it had no impact.
Fixes: a4cbb44c1b ("realtek: convert access to RTL931x analog serdes pages")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19873
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The RTL931x has 14 frontend and at least 26 backend serdes. Currently
the programming functions always need to determine the right backend
serdes from the given frontend serdes on their own. We plan to provide
a consistent serdes mapping to all callers.
As the second step make use of these new functions whenever we
want to access the digital 1 pages. The pages are mapped starting
at 0x100. So the function conversion is as simple as this:
Old:
dsds = (sds - 1) * 2;
rtmdio_931x_read_sds_phy(dsds, page, ...)
New:
rtmdio_931x_read_sds_phy_new(sds, page + 0x100, ...)
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19873
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
7a86ef53075a fix running bridger with stderr debug output
f6afcb04f2ef nl: add missing dump flag for RTM_GETTFILTER
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For some reason 3 of the 4 mdio access functions contain an
artifical delay of 10ms. While it might have been part of
older Realtek SDKs it can no longer be found in current ones.
Remove the delays.
While we are here remove the pre-access bus ready checks.
It is sufficient to run them after the command start. If
anything fails the caller will get an error. This is the
same behaviour as for the other targets.
Finally cleanup the error handling. Something like this makes
no sense at all.
err = rtmdio_838x_smi_wait_op(100000);
if (err)
goto errout;
err = 0;
errout:
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19901
Signed-off-by: Robert Marko <robimarko@gmail.com>
When sending llc packets with vlan tx offload, the hardware fails to
actually add the tag. Deal with this by fixing it up in software.
Fixes: https://github.com/openwrt/openwrt/issues/19916
Reported-by: Thibaut VARENE <hacks@slashdirt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Most drivers have this as const. Especially upstream in the kernel.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19911
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Import upstream patches fixing issues with unreliable temperature
reading on some batches of the MediaTek MT7988 SoCs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Prepare the SerDes patch function to allow different patch sequences
depending on the phy mode. Patches are required to allow devices with a
lightweight bootloader (one that doesn't have a "rtk network init"
command) to use the serdes. Some modes required a different patch
sequence than the one currently used.
Signed-off-by: Damien Dejean <dam.dejean@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19834
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The addition of the soft_reset() function to the RTL8221B PHYs
missed to take care of C22/C45 standalone PHY versions. Especially
on RTL930x switch devices with these PHY the reset fails for the
C45 operation mode. This comes from the fact that the mdio bus
disables C22 read/writes when being set to C45.
Upstream has gained a proper C45 reset function. Use it for the
C45 PHY models.
Fixes: 7e3284eef7 ("generic: use genphy_soft_reset for RealTek 2.5G PHYs")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19843
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We reached the point of no return. Upstream has gained the final
bits for the RTL8226 PHYs. That means.
- RTL8226 MAC side behaves like RTL8221(B)
- It's serdes no longer uses proprietary HSGMII (2.5G SGMII)
- Instead it dynamically switches between SGMII and 2500base-x
This (partly) solves one of the central henn/egg problems of the
Realtek target. To change the MAC/PHY interface mode both sides
need to have all bits in place to do so. But where to start if
so much needs to be done?
Now the PHY side has created facts and it mitigates a lot of
problems. All downstream HSGMII patches and coding can be dropped
in the future.
For now only adapt the only DTS that still maps PHYs to HSGMII.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19843
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The patching sequence of the RTL8214x/8218x is very similar.
Especially the preparation for readiness is always the same.
Provide a common helper to improve readability.
While we are here clean up the changed functions
- Sort variable definitions according to upstream
- simplify some messages
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19810
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Our phy driver can handle some multiport phys (e.g. RTL8218B
or RTL8214FC). To access arbitrary ports some package access
functions have been defined. These were implemented in the
mdio bus with poor knowledge about the phy/mdio dependencies.
So they add unneeded complexity to the bus and the phy driver
must access these external functions directly.
Provide a new helper get_package_phy() that can derive any
phy device in a package from a given phy of that package.
Make use of this local helper and cut the mdio dependency.
While we refactor several firmware patching functions rename
the loop variables to "port" to better indicate what we are
working on.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19810
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that we have a get_base_phy() function a lot code of the RTL8214FC
handling can be cleaned up. To name a few:
- use phy_read/phy_write instead of mdiobus functions or the even worse
phy_package_..._paged() helpers
- replace messages with phydev_info()
- remove if/else statements around copper/fibre handling
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19810
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently phy packages (like RTL8214x/RTL8218x) are patched and
initialized as soon as the first phy of the package is found.
In this situation the shared structure is not finalized because
devm_phy_package_join() has only been called for the first phy.
This is no issue as the patching directly hammers the bus addresses
for the follow-up phys.
In the future we want to simplify the package handling and allow
to access all phy_device structures from only one phy_device of
the package. With this we can use normal phy_read/phy_write.
Switch the probing logic to "late patching". With this we will
initialize the firmware of the package when the last phy of the
package has been found and thus the shared structure is complete.
Provide get_base_phy() as the first package helper that allows
to determine the first phy of the package from any other phy.
While we are here drop the shared structure that only repeats the
phy name and has no other use.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19810
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Plasma Cloud PSX10 Switch is a 8 + 2 port multi-GBit switch with
8x 10/100/1000/2500BaseT Ethernet ports and 2x SFP+ module slot.
Hardware:
- RTL9302C SoC
- Macronix MX25L25645G (32MB flash)
- Winbond W632GU6NB-12 (256MB DDR3 SDRAM - only 128 MB configured*)
- 2x RTL8224 4x 10m/100m/1/2.5 Gigabit PHY
- SFP+ 2x 10GBit slot
- IC+ IP8008 POE+ PSE controller
The switch is powered by 54 Volts 2.77A barrel connector. The internal TTL
serial connector can be used to access the terminal. Pins from 1: TX RX
(unused) GND. Serial connection is via 115200 baud, 8N1.
A reset button is accessible through a hole in the front panel.
*) Only 128 MB of RAM are currently configured because there were
infrequent random memory corruptions detected when using memtester with a
256 MB DT configuration. This could also be reproduced with RTLSDK.
Installation
------------
* The device can be flashed by using sysupgrade command. Either from the
original vendor firmware or using an initramfs (see "Debug")
* Connect serial as per the layout above. Connection parameters: 115200 8N1
* The image must be copied using scp to /tmp of the device
scp openwrt-realtek-rtl930x-plasmacloud_psx10-squashfs-sysupgrade.bin root@[IP address of the device]:/tmp/
* start sysupgrade without saving the original vendor configuration
sysupgrade -n /tmp/openwrt-realtek-rtl930x-plasmacloud_psx10-squashfs-sysupgrade.bin
Installation via u-boot
-----------------------
If you have an TFTP server connected to the switch, it is possible to
directly install the device using the factory image from u-boot
# setup networking and IP of TFP server
rtk network on
setenv ipaddr 10.100.100.99
setenv serverip 10.100.100.20
# get factory image
tftp 0x84000000 factory.bin
# erase firmware partitions
sf probe 0
sf erase 0x100000 0x01f00000
# write firmware to both partitions
sf write ${fileaddr} 0x100000 ${filesize}
sf write ${fileaddr} 0x1080000 ${filesize}
# adjust the boot commands
setenv bootargs "mtdparts=spi0.0:896k(u-boot),64k(u-boot-env),64k(u-boot-env2),15872k(inactive),15872k(firmware2)"
setenv bootcmd "rtk init; bootm 0xb5080000"
# restart
reset
Debug
-----
* Connect serial as per the layout above. Connection parameters: 115200 8N1.
* A tftp server is required, tftpd-hpa works well.
* Power the device, at U-Boot start rapidly hit Esc key to stop autoboot
* Enable network:
rtk network on
* Change ip address of device:
setenv ipaddr 192.168.1.6
* Download initramfs from TFTP server:
tftpboot 0x84000000 192.168.1.111:openwrt-realtek-rtl930x-plasmacloud_psx10-initramfs-kernel.bin
* Boot loaded file:
bootm 0x84000000
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Co-developed-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Plasma Cloud PSX8 Switch is a 8 port multi-GBit switch with
8x 10/100/1000/2500BaseT Ethernet ports.
Hardware:
- RTL9302C SoC
- Macronix MX25L25645G (32MB flash)
- Winbond W632GU6NB-12 (256MB DDR3 SDRAM - only 128 MB configured*)
- 2x RTL8224 4x 10m/100m/1/2.5 Gigabit PHY
- IC+ IP8008 POE+ PSE controller
The switch is powered by 54 Volts 2.77A barrel connector. The internal TTL
serial connector can be used to access the terminal. Pins from 1: TX RX
(unused) GND. Serial connection is via 115200 baud, 8N1.
A reset button is accessible through a hole in the front panel.
*) Only 128 MB of RAM are currently configured because there were
infrequent random memory corruptions detected when using memtester with a
256 MB DT configuration. This could also be reproduced with RTLSDK.
Installation
------------
* The device can be flashed by using sysupgrade command. Either from the
original vendor firmware or using an initramfs (see "Debug")
* Connect serial as per the layout above. Connection parameters: 115200 8N1
* The image must be copied using scp to /tmp of the device
scp openwrt-realtek-rtl930x-plasmacloud_psx8-squashfs-sysupgrade.bin root@[IP address of the device]:/tmp/
* start sysupgrade without saving the original vendor configuration
sysupgrade -n /tmp/openwrt-realtek-rtl930x-plasmacloud_psx8-squashfs-sysupgrade.bin
Installation via u-boot
-----------------------
If you have an TFTP server connected to the switch, it is possible to
directly install the device using the factory image from u-boot
# setup networking and IP of TFP server
rtk network on
setenv ipaddr 10.100.100.99
setenv serverip 10.100.100.20
# get factory image
tftp 0x84000000 factory.bin
# erase firmware partitions
sf probe 0
sf erase 0x100000 0x01f00000
# write firmware to both partitions
sf write ${fileaddr} 0x100000 ${filesize}
sf write ${fileaddr} 0x1080000 ${filesize}
# adjust the boot commands
setenv bootargs "mtdparts=spi0.0:896k(u-boot),64k(u-boot-env),64k(u-boot-env2),15872k(inactive),15872k(firmware2)"
setenv bootcmd "rtk init; bootm 0xb5080000"
# restart
reset
Debug
-----
* Connect serial as per the layout above. Connection parameters: 115200 8N1.
* A tftp server is required, tftpd-hpa works well.
* Power the device, at U-Boot start rapidly hit Esc key to stop autoboot
* Enable network:
rtk network on
* Change ip address of device:
setenv ipaddr 192.168.1.6
* Download initramfs from TFTP server:
tftpboot 0x84000000 192.168.1.111:openwrt-realtek-rtl930x-plasmacloud_psx8-initramfs-kernel.bin
* Boot loaded file:
bootm 0x84000000
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Co-developed-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Signed-off-by: Sharadanand Karanjkar <sk@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/19362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
