Specifications:
SoC: Qualcomm IPQ6010 1.8GHz
RAM: K4A8G165WC-BCTD x2 2GiB
ETH: QCA8075 (3x LAN, 1x WAN)
Flash: ICMAX 8GB eMMC
Power: DC 12V 2A
USB: 1x 3.0
Button: Reset
Flash instructions:
1. Download the initramfs image, rename it to
initramfs.itb, host it with the tftp server.
2. Enter "jdmt018R" to interrupt U-Boot
when the following statement appears:
"disabled console and autoboot in 2 seconds"
3. Run these commands in U-Boot console:
tftpboot initramfs.itb
bootm
4. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/19840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
SoC: Qualcomm IPQ6010 1.8GHz
RAM: K4A4G165WF-BCTD x2 1GiB
Flash: FORESEE 128GB/256GB eMMC
ETH: 4x 1Gbps + 1x 2.5Gbps
WLAN1: QCN5022 2.4GHz AX 2x2
WLAN2: QCN5052 5.8GHz AX 2x2
WLAN2: QCN9024 5.2GHz AX 4x4
Button: Reset, Screen, Wps
Power: DC 12V 3A
USB: 1x 3.0
Flash instructions:
1. Download the initramfs image, rename it to
initramfs.itb, host it with the tftp server.
2. If the stock firmware version is 4.3.0.r4211
or higher, enter "jdmt018R" to interrupt
U-Boot when the following statement appears:
"disabled console and autoboot in 2 seconds"
3. Run these commands in U-Boot console:
tftpboot initramfs.itb
bootm
4. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/19840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
SoC: Qualcomm IPQ6000 1.2GHz
RAM: NT52CB256MB16DP 512MiB
Flash: FORESEE 64GB/128GB eMMC
ETH: QCA8075 (3x LAN, 1x WAN)
WLAN1: QCN5022 2.4GHz AX 2x2
WLAN2: QCN5052 5GHz AX 2x2
Power: DC 12V 2A
Button: Reset, Wps
USB: 1x 3.0
Flash instructions:
1. Download the initramfs image, rename it to
initramfs.itb, host it with the tftp server.
2. If the stock firmware version is 4.3.0.r4211
or higher, enter "jdmt018R" to interrupt
U-Boot when the following statement appears:
"disabled console and autoboot in 2 seconds"
3. Run these commands in U-Boot console:
tftpboot initramfs.itb
bootm
4. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/19780
Signed-off-by: Robert Marko <robimarko@gmail.com>
Match the unit address of both QSDK switch ports with the node's port_id
property. Purely cleanup, no functional change.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21456
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit ab805ec316 ("generic: add missing squashfs config") enabled
CONFIG_SQUASHFS_DECOMP_MULTI_PERCPU in the generic config, so it is no
longer needed in the target configs.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Link: https://github.com/openwrt/openwrt/pull/21465
Signed-off-by: Robert Marko <robimarko@gmail.com>
Interrupts for DWC3 node were completely mixed up - SPI interrupt 62 is
not listed in reference manual at all. It was also causing dtbs_check
warnings:
ipq5018-rdp432-c2.dtb: usb@8af8800 (qcom,ipq5018-dwc3): interrupt-names:0: 'pwr_event' was expected
ipq5018-rdp432-c2.dtb: usb@8af8800 (qcom,ipq5018-dwc3): interrupt-names: ['hs_phy_irq'] is too short
Warning itself was introduced by commit 53c6d854be4e ("dt-bindings: usb:
dwc3: Clean up hs_phy_irq in binding"), but this was trying to bring
sanity to the interrupts overall, although did a mistake for IPQ5018.
IPQ5018 does not have QUSB2 PHY and its interrupts should rather match
ones used in IPQ5332.
Correct it by using interrupts matching the bindings and reference
manual.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21454
Signed-off-by: Robert Marko <robimarko@gmail.com>
BDF for EAP623-Outdoor HD v1 was renamed in the repo, but ipq-wifi
was not updated to reflect that, so do it now to fix broken wifi.
Fixes: #21432
Signed-off-by: Robert Marko <robimarko@gmail.com>
In IPQ5018, the reference clock to the CMN PLL block from the on-board
Wi-Fi has its divider set to 2. This divider wasn't taken into
consideration when calculating the CMN PLL clock rate which meant the
resulting clock rate was doubled.
With the reference clock divider being accounted for in the driver,
correct the assigned clock rate to 4.8GHz.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21453
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add missing dt-bindings/include files needed for compilation of driver.
Enable compilation of the CMN PLL driver by adding the symbols to
Kconfig and Makefile.
Fixes: 468975a985 ("qualcommax: ipq50xx: backport upstreamed patches for adding ipq5018 CMN PLL support")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21453
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is tri-band WiFi6E capable router. Also Zyxel Nebula managed so no real local GUI. To open device 4 screws must be located uder the label.
Four latches are on front and two on each side. Better start from ethernet port side where 3 small latches are easy to handle.
FCC shows It's identical to WSQ65 sold as Zyxel Multy M6E but that's nowhare to be found yet. WSQ65 is not covered by this PR
Speficiations:
* SoC: Qualcomm IPQ5018
* RAM: 1GB DDR3
* Flash: Winbond W25N02KWZEIR 256MB
* UART: PCB "J3" is located left from front LED strip
(VCC/TX/RX/ /GND) 3.3V 115200n8
* Wi-Fi1: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
* Wi-Fi2: QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
* Wi-Fi3: QCN6122 (2x2:2 6 Ghz 802.11an/ac/ax)
* Ethernet: QCA8337 4xLAN 1Gbit / 1xWAN 1Gbit
* Buttons: WPS , Reset
* LEDs: 13 in total
RGB power, RGB wan, RGB status (cloud), RGB wifi, Green wps
* FCCID: I8803891
*Flash Instructions starts with getting root:
connect uart to J3 connector next to the front LEDs
go to failsafe when this shows up in log:
"Press the [f] key and hit [enter] to enter failsafe mode"
execute:
mount_root
passwd -d root
reboot
logon as root:
look for 'Please press Enter to activate this console.'
login is root password is empty
execute:
fw_setenv DebugFlag=0x1
fw_setenv bootdelay=0x2
passwd -d root
backup ubi partition "rootfs" into safe space
reboot
*OpenWrt installation
stop uboot and execute:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.10
tftpboot *-factory.ubi
flash rootfs
reset
or:
tftpboot *-initramfs-uImage.itb
bootm
use sysupgrade as usual
*restore OEM from backup
stop uboot and execute:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.10
tftpboot *-initramfs-uImage.itb
bootm
transfer rootfs.bin backup and execute:
ubiformat /dev/mtd16 -y -f /tmp/rootfs.bin
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
Link: https://github.com/openwrt/openwrt/pull/21042
Signed-off-by: Robert Marko <robimarko@gmail.com>
These patches fix bugs in a patch we backported.
These patch were cherry picked from upstream Linux because it references
a patch we backported in the fixes tag.
The patches were reordered to match the ordering in the upstream Linux kernel.
Fixes: 93173aee96 ("qualcommbe: ipq95xx: Add initial support for new target")
Link: https://github.com/openwrt/openwrt/pull/21366
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add dual-partition upgrade support for Qihoo 360v6 using the generic
bootconfig.sh library. This enables safe system upgrades with automatic
failover capability.
The device uses Qualcomm's bootconfig structure to control A/B partition
switching. The bootloader dynamically maps physical NAND partitions to
logical MTD devices based on the bootconfig, ensuring firmware always
writes to the inactive partition.
Implementation details:
- Use bootconfig.sh library (copied from ipq50xx) for bootconfig operations
- Operate on 'rootfs' partition by name instead of hardcoded offset
- Add magic header validation for safety
- Remove OEM UBI volumes (wifi_fw and ubi_rootfs) before sysupgrade
- Toggle bootconfig before removing OEM volumes
Hardware details:
- SoC: Qualcomm IPQ6000
- Flash: NAND with dual rootfs partitions (mtd16/mtd17)
- Bootconfig: controls slot selection via partition name lookup
Installation:
Standard sysupgrade process. After upgrade, the system will boot
from the new partition while preserving the old system as backup.
The OEM volume cleanup is necessary because these volumes are created
by the stock firmware and are not automatically cleaned by the standard
nand_upgrade_prepare_ubi() function, which only removes volumes named
'kernel', 'rootfs', and 'rootfs_data'. Without this cleanup, the remaining
OEM volumes consume available space, causing the creation of rootfs_data
to fail during sysupgrade.
Tested on Qihoo 360v6 running stock firmware and OpenWrt.
Signed-off-by: Zhenyu Qi <qzydustin@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/21154
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit 423cda97f9.
It appears that this broke remoteproc on some devices, so revert for now.
Signed-off-by: Robert Marko <robimarko@gmail.com>
ipq5018 do not support freq scaling and therefore stuck on 800Mhz
This patch allows CPU to run with 1.008 Ghz as designed
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
Link: https://github.com/openwrt/openwrt/pull/21185
Signed-off-by: Robert Marko <robimarko@gmail.com>
Interrupt vector for reo2host-status is wrongly assigned.
Status interrupts weren't received and a workaround was applied to
mac80211 to periodically poll the reo status ring. Therefore, the
workaround can be removed with the proper hardware interrupt line
assigned.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21271
Signed-off-by: Robert Marko <robimarko@gmail.com>
Linksys MX6200 is a triband Wi-Fi 6E wireless router.
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Nanya NT5CC256M16ER-EK (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
QCN6122 (2x2:2 6 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to:
- LAN Port: Internal IPQ5018 GE PHY
- WAN Port: Maxlinear Ethernet GPY115C PHY
* Flash: Macronix MX35UF2GE4AD (256 MiB)
* LEDs: 1x multi-color PWM LED
* Buttons: 1x WPS (GPIO 27 Active Low)
1x Reset (GPIO 28 Acive Low)
* FCC ID: 2AYRA-08436
Flash instructions:
************************************************************************
NOTE: serial access is required! Although the web UI allows you to
install the Openwrt image, secure boot is enabled which will prevent
booting an unsigned image. The boot sequence must be adjusted in U-boot
to allow booting unsigned images.
************************************************************************
1. On OEM firmware, login to the web UI (typically @ http://192.168.1.1)
and click 'CA' in the bottom right corner.
Then click -> Connectivity -> Manual Upgrade.
Alternatively, browse to
http://<router IP>/fwupdate.html.
Upload openwrt-qualcommax-ipq50xx-linksys_mx6200-squashfs-factory.ubi.
Continue with step 5.
2. Installation on alternate partition using serial connection from OEM
firmware (default login: root, password: admin):
flash_erase /dev/mtd19 0 0
nandwrite -p /dev/mtd19 openwrt-qualcommax-ipq50xx-linksys_mx6200-squashfs-factory.ubi
reboot
Continue with step 5.
3. Installation using serial connection from initramfs
setup tftp server listening on IP in 192.168.1.0/24 (other than the
router IP 192.168.1.1). In U-boot, load the initramfs image to memory:
tftp $loadaddr <your IP>:openwrt-qualcommax-ipq50xx-linksys_mx6200-initramfs-uImage.itb
boot the image using command:
bootm $loadaddr
when fully booted, scp the sysupgrade image to your router IP (default:
192.168.1.1):
scp -O <path>/openwrt-qualcommax-ipq50xx-linksys_mx6200-squashfs-sysypgrade.bin root@192.168.1.1:/tmp/
use sysupgrade to flash the image to nand:
sysupgrade -n -v /tmp/openwrt-qualcommax-ipq50xx-linksys_mx6200-squashfs-sysupgrade.bin
Continue with step 5.
4. Optionally install on alternate partition. From Openwrt:
mtd -r -e rootfs_1 -n write openwrt-qualcommax-ipq50xx-linksys_mx6200-squashfs-factory.ubi rootfs_1
Continue with step 5.
5. Setup U-boot for ability to dual boot signed (stock) and non-signed
(Openwrt) images with auto-detection.
From U-boot, run (be aware: copy line by line):
setenv setnandbootargs 'setenv bootargs init=/sbin/init ubi.mtd=rootfs rootfstype=squashfs rootwait'
setenv nandinitcmd 'setenv mtdids nand0=nand0; run setrootfscmd; ubi part rootfs 2048'
setenv setrootfscmd 'if test $boot_part = 1; then setenv mtdparts mtdparts=nand0:0x${imgsize}@0x${prikern}(rootfs); else setenv mtdparts mtdparts=nand0:0x${imgsize}@0x${altkern}(rootfs); fi'
setenv readhdr1cmd 'ubi read $loadaddr kernel 0x40; setexpr IMGOFF $loadaddr + 0x10; setexpr CODEOFF $loadaddr + 0x14; setexpr SIGOFF $loadaddr + 0x1c; setexpr CERTOFF $loadaddr + 0x24'
setenv readhdr2cmd 'setexpr.l HDR *$loadaddr; setexpr.l IMGSZ *$IMGOFF; setexpr.l CODESZ *$CODEOFF; setexpr.l SIGSZ *$SIGOFF; setexpr.l CERTSZ *$CERTOFF; setexpr TSIZE $CODESZ + $SIGSZ; setexpr TSIZE $TSIZE + $CERTSZ'
setenv testmbncmd 'if test $HDR -ne edfe0dd0 -a $IMGSZ -eq $TSIZE; then bootipq; else ubi read $loadaddr kernel $kernsize; run setnandbootargs; bootm $loadaddr; fi'
setenv bootcmd2 'if test $auto_recovery = no; then bootipq; else run nandinitcmd; run readhdr1cmd; run readhdr2cmd; run testmbncmd; fi'
setenv bootcmd 'run bootcmd2'
saveenv
6. Back to the OEM firmware.
Download firmware from OEM website:
MX6200: https://support.linksys.com/kb/article/408-en/
From serial/SSH, in Openwrt, flash OEM firmware to alternate partition:
mtd -r -e rootfs_1 -n write FW_MX6200_1.0.11.216041_prod.signed.img rootfs_1
Switching active partition:
1. From U-boot, executive the following to switch to partition 1:
setenv boot_part 1
for partition 2:
setenv boot_part 2
2. From Openwrt:
fw_printenv boot_part
In case it's 1:
fw_setenv boot_part 2
. /lib/upgrade/platform.sh
linksys_bootconfig_set_primaryboot "0:bootconfig" 1
linksys_bootconfig_set_primaryboot "0:bootconfig1" 1
In case it's 2:
fw_setenv boot_part 1
. /lib/upgrade/platform.sh
linksys_bootconfig_set_primaryboot "0:bootconfig" 0
linksys_bootconfig_set_primaryboot "0:bootconfig1" 0
and
reboot
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21038
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for upgrades on dual firmware Linksys devices with the
partition table stored in SMEM and that store both the kernel and rootfs
in a single partition. Switching the active boot partition requires
updating the partition info table in SMEM in addition to setting
the active boot partition in a U-boot variable as U-boot will keep them
in sync upon reboot if they're not.
U-boot always sets the name of the active partition to rootfs and that
of the inactive partition to rootfs_1 in SMEM. when Linux loads the
partition table from SMEM it will load the right partition based on the
offset set in the SMEM partition table. For upgrades, flashing to the
alternate partition will always be to rootfs_1, while flashing the
current partition will be on rootfs.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21038
Signed-off-by: Robert Marko <robimarko@gmail.com>
The BOOTCONFIG partition is used by Qualcomm's boot chain to store
metadata about the device's startup configuration. It contains info such
as versioning, configuration flags, primary boot partition, and more.
Newer devices with dual boot partitions not only store the active boot
partition in a U-boot variable but also in partition info in the
BOOTCONFIG partition. As such, add library functions to set and toggle
the active boot partition.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21038
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move setting kernel bootargs from the base template down to the
respective Linksys board files. This allows for having devices which
require different bootargs use the base template device tree file.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21038
Signed-off-by: Robert Marko <robimarko@gmail.com>
The partition table on Linksys devices with a Qualcomm AX IPQ SoC is
stored in SMEM. As such, load partition table from SMEM rather than
statically defining them in their respective device trees. This helps
generalize the base template and requires less maintenance.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21038
Signed-off-by: Robert Marko <robimarko@gmail.com>
The current ath11k driver does not support loading m3 firmware for
IPQ5018 and QCN6122 wifi. Although m3 firmware entries are specified
in Q6 WCSS nodes, the driver actually skips loading them. Editing the
driver to force loading m3 results in Q6 crashes and non-functioning
wifi. As such, remove m3 firmware entries for all boards until there's
proper support in the ath11k driver.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21110
Signed-off-by: Robert Marko <robimarko@gmail.com>
Just like it has already been changed for v2, use the ascii-eq-delim-env
driver to extract the label mac from the devinfo partition.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20732
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add missing address-cells and size-cells properties under the switch's
ports node to fix a multitude of below build warnings:
Warning (reg_format): /soc@0/mdio@90000/ethernet-switch@11/ports/port@1:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): /soc@0/mdio@90000/ethernet-switch@11/ports/port@1: Relying on default #address-cells value
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20982
Signed-off-by: Robert Marko <robimarko@gmail.com>
Although the bootloader tries to 'fixup' the qpic nand node, it actually
can't find it as the node was renamed to spi based on the new driver
architecture. The added benefit is that it also silences build warning:
Warning (spi_bus_reg): /soc@0/spi@79b0000/partitions: missing or empty reg property
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
---
Node rename:
old node name: qpic-nand@79b0000
new node name: spi@79b0000
Bootloader logs:
Booting using the fdt blob at 0x44d3fc78
Uncompressing Kernel Image ... OK
Loading Device Tree to 4a3f6000, end 4a3ff805 ... OK
fdt_fixup_qpic: QPIC: unable to find node '/soc/qpic-nand@79b0000'
parse_fdt_fixup: unable to find node '/soc/qpic-nand@79b0000/'
Link: https://github.com/openwrt/openwrt/pull/20982
Signed-off-by: Robert Marko <robimarko@gmail.com>
CPR conversion to of_property_present is broken in multiple places, either
by leaving the comma after now the last argument or by attempting to replace
an instance that actually uses the returned length.
So, lets fix these in order for qualcommax to compile again.
Fixes: c9e7f32c4c ("treewide: use of_property_present")
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Zyxel NWA210AX is a wall- and ceiling-mountable access point (AP).
Hardware specifications:
- SoC: Qualcomm IPQ8071A
- RAM: 1 GB (Samsung K4A8G165WC-BCTD)
- Flash: 8 MB (Winbond W25Q64DW), 256 MB (Winbond W29N02GZ)
- Ethernet: 1x 2.5 Gbps RJ45 port (QCA8081), 1x 1 Gbps RJ45 port (AR8033)
- WiFi: 2.4 GHz 802.11ax/b/g/n (QCN5024), 5 GHz 802.11 ac/ax/n (QCN5054)
- Power: DC 12V/PoE 802.3at
- Button: Reset
- LEDs: Multicolour red/green/blue/white via LP5562
Installation/flashing instructions:
1. In OEM web interface navigate to gear icon → System → SSH and enable SSH.
2. Log in via SSH (username/password are the same as for the web interface).
3. Run "debug dual-image show".
4. Verify that output is "Current Image num: 1".
5. If this is not the case (i.e. if the output is "Current Image num: 0"):
a. Either flash a fresh version of factory firmware, or
b. run "debug dual-image set boot-image image1" and then run "reboot".
6. Log in via SSH again and verify that output is "Current Image num: 1".
7. Rename "openwrt-qualcommax-ipq807x-zyxel_nwa210ax-squashfs-factory.bin" to
"openwrt.bin" to avoid upload errors in the OEM web interface.
8. Reopen OEM web interface, navigate to wrench icon → File Manager →
Firmware Package and upload the bin file. Once the upgrade process is
finished and OpenWrt has booted, the LED will light up green.
Switching between OpenWrt and OEM firmware:
- OpenWrt → Zyxel via ssh command "zyxel-bootconfig-ipq807x set image1".
- Zyxel → OpenWrt via ssh command "debug dual-image set boot-image image0".
This commit is based on the work of Pascal Beleiu <pascal@beleiu.de>:
93ca21f3 (qualcommax: ipq807x: add support for Zyxel NWA210AX, 2025-03-17)
Signed-off-by: Eric Schäfer <eric@es86.de>
Link: https://github.com/openwrt/openwrt/pull/19828
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit 741689a335.
Only after merging I remebered the reason why it was changed to 0,0 [1].
[1] 1e20f7b6c6
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use compatible before reg for consistency.
Also fixup the wifi node name for some qualcomm platforms where the slot
is 1 instead of 0.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20351
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport upstream patch to add support for the ESMT F50L1G41LC flash
chip. It is used in multiple Cudy products manufactured starting
November 2025.
Link: https://github.com/openwrt/openwrt/pull/20962
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
IPQ5018 based boards come in multiple wireless architectures.
The SOC itself provides 2.4G wifi while 5G wifi is added by either an
IPQ5018-specific QCN6122 (2x2) solution or by the more generally
available PCIe-based QCN9074 (4x4) wifi chip.
On IPQ5018/QCN6122-based boards, both QCN6122 and IPQ5018 wifi is
initialized by IPQ5018 firmware which comes in different versions:
- IPQ5018: firmware files to initialize WCSS and the internal wifi chip
- IPQ5018/QCN6122: above + additional firmware segments to initialize
the QCN6122 chip incl. (de-)assertion of resets and clocks enablement
OpenWrt currently packages the combined IPQ5018/QCN6122 firmware for
both architectures. As such, let's switch to using IPQ5018-only firmware
for boards not packed with QCN6122 chip(s) and keep using the shared
firmware for devices that do have QCN6122(s) chips.
This helps us move to using upstreamed IPQ5018 firmware while using the
legacy repo for IPQ5018/QCN6122 firmware and rule out any initialization
conflicts/issues caused by loading QCN6122 on IPQ5018-only boards.
While at it, default to the secure WCSS remoteproc driver sent upstream
for review, move QCN6122 wifi nodes to a separate dtsi, override the Q6
node to load the multi-PD-based architecture remoteproc driver for
needed only by IPQ5018/QCN6122 designs, reference said dtsi in
boards packed with QCN6122 wifi chip(s), and add provision for migrating
the radio path as the wifi nodes now adhere to linux device tree naming
conventions.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20928
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for qcom remoteproc WCSS secure PIL driver.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20928
Signed-off-by: Robert Marko <robimarko@gmail.com>
All users of regular CONFIG_NVMEM_U_BOOOT_ENV have been converted to use
layouts.
CONFIG_NVMEM_U_BOOT_ENV selects the layout variant anyway so this is
safe to do.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16376
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The child node "partitions" doesn't have "reg" property. Hence, we
don't need to use "#address-cells" and "#size-cells" to describe the
reg property information.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20942
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The child node "partitions" doesn't have "reg" property. Hence, we
don't need to use "#address-cells" and "#size-cells" to describe the
reg property information.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20942
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
CMCC PZ-L8 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on IPQ5000.
Specifications:
- SoC : Qualcomm IPQ5000
- RAM : Integrated 256MiB DDR3L
- Flash : 128 MiB SPI-NAND (ESMT F50D1G41LB)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm IPQ5000 (SoC)
- 5 GHz : Qualcomm Atheros QCN6102
- Ethernet : 4x 10/100/1000 Mbps
- switch : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO) : 2x LEDs, 2x Keys
- UART : Through-hole on PCB, 4pins in the middle of the black aluminum heat sink
- assignment : 3.3V, GND,TX, RX (from left to right)
- settings : 115200n8
- Power : 12 VDC, 1 A
Flashing Instructions:
1. SSH Method
(1) Enable SSH on the stock firmware
a. Version 501.8 and 501.9:
Log in to http://192.168.10.1 with the password on the sticker
Append "/admin/system/admin" to the URL and press Enter
Delete "Dropbear instance", click "Add instance", then "Save and Apply"
Reboot the router
b. Version 501.11 and 501.12:
While the router is running the stock firmware, press and hold the reset button for 20-30 seconds
Open http://192.168.10.1:56781 and login with username "root" and the password on the sticker
Run "vi /etc/config/dropbear" and delete the line "option enable '0'"
Reboot the router
(2) Upload the factory.ubi file to router's /tmp directory (using scp or wget)
and execute the following commands in the router's shell
export rootfs=$(cat /proc/mtd | grep rootfs | grep -v _ | cut -d: -f1)
ubidetach -f -p /dev/${rootfs}
ubiformat /dev/${rootfs} -y -f /tmp/factory.ubi
2. U-Boot Method using UBI Image
Place the factory.ubi file on your TFTP server, enter U-Boot CLI and exec these commands
tftpboot <your_tftp_server_ip>:factory.ubi
flash rootfs
reset
3. U-Boot Method using initramfs Image
(1) Place the openwrt-*-initramfs-fit-uImage.itb file on your TFTP server
and rename it to initramfs.bin
(2) Enable serial console, enter to U-Boot CLI and exec these commands
tftpboot <your_tftp_server_ip>:initramfs.bin
bootm
(3) Once boot completed, upload the sysupgrade.bin file to router's /tmp directory
(using scp or wget) and execute the following command in openwrt shell
sysupgrade -n /tmp/sysupgrade.bin
Switching to the Stock Firmware:
Please follow the commit 3b7d72bc2e
Partition Layout (Stock Firmware):
0x000000000000-0x000000080000 : "0:SBL1"
0x000000080000-0x000000100000 : "0:MIBIB"
0x000000100000-0x000000140000 : "0:BOOTCONFIG"
0x000000140000-0x000000180000 : "0:BOOTCONFIG1"
0x000000180000-0x000000280000 : "0:QSEE"
0x000000280000-0x000000380000 : "0:QSEE_1"
0x000000380000-0x0000003c0000 : "0:DEVCFG"
0x0000003c0000-0x000000400000 : "0:DEVCFG_1"
0x000000400000-0x000000440000 : "0:CDT"
0x000000440000-0x000000480000 : "0:CDT_1"
0x000000480000-0x000000500000 : "0:APPSBLENV"
0x000000500000-0x000000640000 : "0:APPSBL"
0x000000640000-0x000000780000 : "0:APPSBL_1"
0x000000780000-0x000000880000 : "0:ART"
0x000000880000-0x000000900000 : "0:TRAINING"
0x000000900000-0x000004300000 : "rootfs"
0x000004300000-0x000007d00000 : "rootfs_1"
Notes:
This device is almost the same as ELECOM WRC-X3000GS2, including partition layout and the dual-boot feature.
Known Issues:
- All Wi-Fi related peripherals are disabled in device tree, since 256 MiB RAM is too few for ath11k.
- This device has another version with nand flash FM25SL01, which is not supported at the moment.
https://github.com/immortalwrt/immortalwrt/blob/master/target/linux/mediatek/patches-6.12/342-mtd-spinand-Support-fmsh.patch
MAC Addresses:
Interface MAC Address Location (binary)
LAN A4:39:B6:xx:xx:9D (0:ART, 0x00-0x05)
WAN A4:39:B6:xx:xx:9E (0:ART, 0x06-0x0B)
2.4 GHz A4:39:B6:xx:xx:9F (0:ART, 0x0C-0x11)
5 GHz A4:39:B6:xx:xx:A0 (0:ART, 0x12-0x17)
Signed-off-by: Chang Liu <jssqliuchang@gmail.com>
symtom: macs not properly incremented (all macs the same)
solution: set correct offset to mac location
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20664
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
There is no need to add a "cs-gpios" property if chip select pin is
directly controlled by the SPI host hardware.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19845
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The imagebuilder is not intended to build initramfs images. Some
profiles attempt to do this and succeed, due to buildroot leaking
the initramfs-kernel into staging_dir; others attempt it, but fail
due to not having initramfs binaries present in the imagebuilder.
Fix this by adding an explict guard around the unsupported generation
of the initramfs images. This saves space and time during imagebuilder
runs, fixes those that are currently broken and protects against future
breakage for profiles that inadvertently work now.
Fixes: https://github.com/openwrt/openwrt/issues/20151
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20347
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit 468975a985 changed the XO board clock definition from a fixed
clock to a fixed rate clock in the dtsi.
As such, boards must use clock dividers and multipliers to calculate
the clock rate based on the referenced parent clock.
Fixes: 5d2994a73e ("qualcommax: ipq50xx: Add support for Yuncore AX850")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20405
Signed-off-by: Robert Marko <robimarko@gmail.com>
The former is deprecated. Fixes dtc warning.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20116
Signed-off-by: Robert Marko <robimarko@gmail.com>
No functional changes intended.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20131
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add node to support the second UART node controller in IPQ5018.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20090
Signed-off-by: Robert Marko <robimarko@gmail.com>
