CONFIG_REGULATOR_QCOM_LABIBB is being disabled by targets manually, so
instead lets disable it in generic config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Instead of disabling CONFIG_REGULATOR_QCOM_SPMI manually per target,
lets simply disable it in generic config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
CONFIG_REGULATOR_QCOM_USB_VBUS showed up on Layerscape recently, and it
looks like multiple targets disable it manually, so simply disable it in
generic configuration instead.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Enable and configure DMA contiguous memory allocator. Without this
CMA itself will be disabled.
Fixes: ae8bf1a26e ("imx: add imx8m support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/21950
Signed-off-by: Robert Marko <robimarko@gmail.com>
The configuration for the dlink,dir-1360-a1 also changed the settings
for the devices defined on top of it. "lan1 lan2 lan3 lan4" "wan" is
the default configuration, no need to add it here.
Fixes: 7a8e2efed5 ("ramips: add support for D-Link DIR-1360 A1")
Reported-by: schmars in IRC
Link: https://github.com/openwrt/openwrt/pull/22179
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Userspace handling is deprecated. Once mac-base goes upstream, the patch
itself can go upstream as well.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22058
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use clock index macros defined in dt-bindings header to improve the
code readability.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22163
Signed-off-by: Robert Marko <robimarko@gmail.com>
The GPIO line connecting to the reset signals of the GS1900-24E(A1)'s
external ICs (RTL8218B phys and RTL8231 expander) cannot be asserted by
the MDIO subsystem, as the reset is shared between busses.
To prevent users from accidentally asserting the reset line, a GPIO hog
is created to permanently de-assert the signal, reliably keeping the
phys and GPIO expanders on.
Tested-by: Simon Fischer <simi.fischa@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The reset line wired to the RTL8231 on the GS1900 series may also
connect to other external ICs on the board. On the GS1900-24E, the
reset line is wired (via buffers) to the board's RTL8231 expanders and
the RTL8218 phys. As these external devices (phys) are on different
busses, the reset line shouldn't be specified on one bus or the other.
Drop the reset specification from the generic GPIO description, so it
can be added back on a per-device basis after confirming the behavior.
Link: https://github.com/openwrt/openwrt/issues/18620
Fixes: fd978c2e80 ("realtek: Enable Zyxel GS1900's RTL8231 reset line")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The DASAN H660GM-A GPON ONT exists in two hardware variants, one
distributed by ISPs and one sold directly by the manufacturer [1].
Split the single DTS into a shared dtsi and per-variant DTS files
with the correct GPIO mappings, flash layout, and LED definitions.
Variant comparison:
Feature | Airtel | Generic
---------------+---------------------------+-------------------------
Supplied by | Airtel Xstream Fiber | Retail
Flash | Micron MT29F2G01ABAGD | Micron MT29F1G01ABAFD
| 256 MB | 128 MB
Known P/N | DPW-G-P-66GMAZ-A3 | DPW:G-P-660GMAY-G0
| (some units unlabelled) | DPW:G-P-660GMAY-G3
WPS LED | Yes | No
WLAN button | No | Yes
USB LED | No | Yes
LAN LEDs | Green only | Green + Amber
[1] https://dasanns.com/en/solution/detail.php?mode=view&cat_no=32&offset=&idx=122
Tested-by: Arif Rahman Hakim <arif2785id@gmail.com>
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22095
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On MT7620-class platforms (CONFIG_NET_RALINK_MT7620) we observe sporadic
wrong-jump-targets, kernel oopses, hanging, corrupted backtraces or even
"half-written" instructions when the compiler emits a direct 'jal imm26'
call.
This is triggered in:
- the small random helpers inside get_random_u32_below(), and
- the blkcg_maybe_throttle_current() call in resume_user_mode_work().
This patch forces those two call sites to use an indirect call via
a volatile function pointer (load into register + jalr) when building
for MT7620, avoiding embedding a 26-bit immediate jump target.
Additionally, on MT7620 builds the exec path in fs/exec.c is modified:
- skip arch_align_stack() + PAGE_ALIGN() in setup_arg_pages()
because the micro-randomization (< PAGE_SIZE) implemented by many
ports (including MT7620) is negated immediately by PAGE_ALIGN().
Skipping the redundant PAGE_ALIGN() reduces exposure to the
problematic code pattern.
These changes are targeted workarounds for MT7620; behavioral logic is unchanged.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/20553
Signed-off-by: Robert Marko <robimarko@gmail.com>
Instead of redifining the DEVICE_PACKAGES, make sure to expand the list
so yafut is included by default as well.
Fixes: 42cd486787 ("ath79: remove kmod-ath9k and wpad from Mikrotik RB750r2")
Signed-off-by: Robert Marko <robimarko@gmail.com>
The KSZ9477 driver was added to the cortexa53 kernel to support the
Gateworks Venice product family which has a board with this switch. Now
that the kmod-dsa-ksz9477 driver is available as a package remove the
static configuration ad add the package.
This resolves an issue caused by having the switch driver static and the
PHY driver as a module such that the PHY driver was not registered early
enough to be used causing some errata to not be worked around.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/22120
Signed-off-by: Robert Marko <robimarko@gmail.com>
The makefile recipe is wrong and a module compilation tries
to build each object individually. Fix that. This allows to
build the dsa driver as a module.
Suggested-by: Balázs Triszka <info@balika011.hu>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22121
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ethernet driver has a hard link to the dsa driver. Especially
the setup_tc() function must be available when the driver loads.
Decouple it by using a dsa callback recipe.
Suggested-by: Balázs Triszka <info@balika011.hu>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22121
Signed-off-by: Robert Marko <robimarko@gmail.com>
We do not want to rely on the soc_info structure. But at the moment
it is still referenced in several places. Add an EXPORT() to it.
So drivers that need access to this structure can be build as modules.
Suggested-by: Balázs Triszka <info@balika011.hu>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22121
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RB750r2 (HEXLite) does not have wifi and those packages bloat the image
by a significant amount. When building a custom image with WireGuard and
booting that from initramfs, there wasn't enough space left in tmpfs to
upload and flash the squashfs image. Investigating what packages I could
remove, I discovered these unneeded ones.
Signed-off-by: Eicke Herbertz <wolletd@posteo.de>
Link: https://github.com/openwrt/openwrt/pull/22134
Signed-off-by: Robert Marko <robimarko@gmail.com>
Given that Linksys is the same brand and probably use the same OEM, it
stands to reason all devinfo hw_mac_addr implementations are the same.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22092
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated. NVMEM allows more flexibility in terms
of exotic setups while keeping correct MAC addresses.
env-size taken from file in uboot-envtools.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22107
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated. NVMEM allows flexibility in terms of
exotic setups by avoiding random MAC addresses.
u-boot env-size taken from the entry in uboot-envtools
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22107
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport patches from upstream linux and mtk-openwrt-feeds to fix
MT7981 register offset issue and correct MT798x IES register config.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21423
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The banana pi r4 comes with 2 sfp+ ports running at 10gbps
Readd support for aquantia sfp+ modules that was removed by
57a127c9e7Closes: #19878
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19884
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Avoid a family_id check and derive the values from the cpu port.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22068
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Place it where it belongs.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22068
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Place it where it belongs.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22068
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Two different irq handlers exist for RTL83xx and RTL93xx. Basically
they do always the same.
- Check transmit interrupts (not needed anymore)
- Check rx overflow interrupts (not needed anymore)
- Determine rx interrupts and queues that must be processed.
- In case of RTL839x check for L2 interrupts
With all the recent refactoring their logic is more or less the
same. Merge them into one handler. For better readability add a
helper that determines the work (aka rings) that needs to be
processed.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22023
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is a wrong port assignment for the 4 SFP+ ports
on that device. Additionally the transmit polarity
change option was missed. Fix that.
Fixes: f88135b ("realtek: add support for Linksys LGS352C")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22119
Signed-off-by: Robert Marko <robimarko@gmail.com>
RTL931x organizes MACs into 12 groups (one per SerDes) that must be
explicitly enabled before link establishment. Without initialization,
link may fail or packets may be corrupted, especially in USXGMII/XSGMII
modes. This is the case for devices which lack initialization by the
bootloader.
Simply enable all MACs in all groups by writing 0xffffffff to the
registers. Unused MACs and reserved bits are harmless, avoiding complex
logic to always set only needed MACs.
This is placed in the PCS driver since the MAC groups are assigned per
SerDes and the DSA driver lacks SerDes awareness (on purpose)
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22088
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware:
- SoC: RTL9313
- Memory: 512MB
- Flash: SPI-NOR 32MB (GigaDevice GD25Q256EFIR)
- Ethernet: 12x 1/2.5/10 Gbps (SFP+)
- LED/Keys (GPIO): 1x/1x
- UART: "Console" port on the front panel
- type: RS-232C
- connector: RJ-45
- settings: 9600n8 / 115200n8
- Watchdog: Diodes PT7A7514WE
- Monitoring: LM75A
- Power: 100-240 VAC 50/60 Hz C13/C14
Important notes:
---------------
* the device uses 9600 Baud by default but this extremely slows down the
device when using the serial console. OpenWrt is configured to use
115200 Baud. If you need to enter the bootloader, you need to use 9600
Baud.
* PT7A7514WE watchdog is fed through hardware-assisted SYS_LED. However,
the bootloader seems to deactivate that again during autoboot. There's
a quirk in early arch setup for this.
* a kernel binary "nos.img" needs to be stored into JFFS2 filesystem
using 4KiB erase block instead of 64KiB.
* V1 is the version with the 19"-sized case. As of 2026, there's a newer
version with a narrow case.
Flash instructions using initramfs image:
-----------------------------------------
(mostly taken from 0dc0b98295)
1. Prepare TFTP server with an IP address in 192.168.2.0/24.
2. Connect your PC to Port 1 on SKS8300-12X.
3. Power on SKS8300-12X and interrupt autoboot by Ctrl + B.
4. Login to the vendor CLI by Ctrl + F and "diagshell_unipoe_env" as password.
5. Switch baudrate to 115200 by running a command and then reconnect
with different settings:
baudrate 115200
6. Switch to U-Boot CLI by "debug_unish_env".
7. Enable Port 1 with the following commands:
rtk 10g 0 fiber1g # (or fiber10g if 10GBase-*R)
rtk ext-devInit 0 # init RTL8231 that holds SFP GPIOs
rtk ext-pinSet 2 0 # set tx-disable of port 1 to LOW
8. Transfer initramfs image via TFTP and boot it:
tftpboot 0x82000000 <serverip>:<image name>
bootm 0x82000000
9. On the initramfs image, backup the stock firmware if needed.
10. Upload (or download) sysupgrade image to the device.
11. Erase "firmware" partition to cleanup JFFS2 of stock FW:
mtd erase firmware
12. Perform sysupgrade with the sysupgrade image.
13. Wait until the flash completes and the system reboots into OpenWrt.
Reverting to stock firmware:
----------------------------
(taken from 0dc0b98295)
1. Prepare OpenWrt SDK to use the mkfs.jffs2 tool contained in it
Note: the official mkfs.jffs2 tool in mtd-utils doesn't support 4KiB
erase size and not usable for SKS8300-8X
2. Create a directory for working
3. Download official firmware for SKS8300-8X from XikeStor's official
website
4. Rename the downloaded firmware to "nos.img" and place it to the
working directory
5. Create a JFFS2 filesystem binary with the working directory
/path/to/mkfs.jffs2 -p -b -U -v -e 4KiB -x lzma \
-o nos.img.jffs2 -d /path/to/working/dir/
6. Upload the created JFFS2 filesystem binary to the device
7. Erase the "firmware" partition
mtd erase firmware
8. Write the JFFS2 filesystem binary to the "firmware" partition
mtd write /path/to/nos.img.jffs2 firmware
9. After writing, reboot the device by power cycle
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21922
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Make xikestor-nosimg a common recipe in the Makefile to allow usage for
other subtargets too, not only rtl930x.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21922
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On some XikeStor switches (SKS8300-8X, SKS8300-12X), the SYS_LED/GPIO0 is
used to feed an external PT7A7514WE watchdog. While this was no issue on
SKS8300-8X, the bootloader on the SKS8300-12X seems to deactivate the
automatic feeding on purpose by setting the pin function of to GPIO0
instead of SYS_LED. This kills the periodic signal generated on that pin.
This causes the kernel to just stop quite early and reset the system
entirely.
Because this happens very early, it doesn't work to define this as a
pinctrl entry or GPIO hog. The drivers aren't even loaded at that stage.
To work around the issue, we need to configure this in the arch-specific
early setup. An affected device needs to have a corresponding node in
the DTS that is picked up then.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21922
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use NVMEM in device tree to set the label and eth0 MAC address based on
the U-Boot environment.
Invididual port MAC addresses and bridge MAC are still handled in the
02_network script to maintain the current assignment.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/22055
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a preparation to convert some more RTL838x devices to NVMEM.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/22055
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Startup of mdio on a RTL8216 based device currently shows the
following warnings.
[1.948608] skip polling setup for unknown PHY 001ccaf3 on port 0
[1.968920] skip polling setup for unknown PHY 001ccaf3 on port 8
[1.989171] skip polling setup for unknown PHY 001ccaf3 on port 16
[2.009704] skip polling setup for unknown PHY 001ccaf3 on port 20
[2.030209] skip polling setup for unknown PHY 001ccaf3 on port 24
[2.052270] realtek-otto-serdes-mdio 1b000000.switchcore:mdio-serdes:
Realtek SerDes mdio bus initialized, 12 SerDes, 64 pages
Add the phy detection to the mdio bus so that polling setup works.
While we are here sort the phy ids alphabetically.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22109
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit 72f43ac220.
The NVMEM codepath does not perform automatic byte conversion. It can be
fixed but the upstream version is quite different from the local
mac80211 patch. Revert until mac80211 gets updated and the whole mess
can get squared away.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22091
Signed-off-by: Robert Marko <robimarko@gmail.com>
Make clearer which field belongs to which register. For this
sort the fields below the registers and use indentation.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22075
Signed-off-by: Robert Marko <robimarko@gmail.com>
PHY polling setup has found a home in the mdio driver. For RTL931x
there still exists a setup sequence for polling type (serdes/mdio)
in the DSA driver. Put it where it belongs.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22075
Signed-off-by: Robert Marko <robimarko@gmail.com>
Get rid of defines that are not used in the driver.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22100
Signed-off-by: Robert Marko <robimarko@gmail.com>
This define is used nowhere. Remove it.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22100
Signed-off-by: Robert Marko <robimarko@gmail.com>
The MAC_FORCE_MODE_CTRL register is only used for the CPU port.
No need to repeat the port register calculation for each usage.
Simply point to the cpu port register directly.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22100
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fixed the compilation of kernel with the loadable modules support turned off
Signed-off-by: Maksim Dmitrichenko <dmitrmax@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22041
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove unneeded includes from setup.c and adapt comments.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22084
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add missing CONFIG_LEDS_QCOM_LPG symbol.
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22096
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit 041ef9648d ("qualcommbe: move Device DTS to dedicated DTS
directory") introduced a dedicated DTS directory and set DEVICE_DTS_DIR
to ../dts as default. This broke the rdp433 device build since its DTS
resides in the kernel tree (applied via patches), not in the target dts
directory.
Fix this by overriding DEVICE_DTS_DIR for rdp433 to point to the kernel
DTS directory.
Fixes: 041ef9648d ("qualcommbe: move Device DTS to dedicated DTS directory")
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22096
Signed-off-by: Robert Marko <robimarko@gmail.com>
Due to confusing Documentation, the SPI and SLIC base clock and
register location for Airoha AN7583 SoC were wrong.
Fix them with new updated Documentation source to provide correct
clock support.
Fixes: c5b12fc02a ("airoha: Introduce support for Airoha AN7583 SoC")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reuse Device/FitImage recipe instead of open coding it and
drop duplicate KERNEL_INITRAMFS recipe for eDPU.
While at it, lets clean up the boot script to drop uneeded console
setting, earlycon etc.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Move the Device/FitImage recipe to the generic image Makefile to avoid
duplicating it for other subtargets.
Will be used for uDPU/eDPU.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This allows to drop a family condition check and in the future
allows to merge nowadays splitted functions. While we are here
replace a hardcoded 0xc value with the new value for better
readability.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21999
Signed-off-by: Robert Marko <robimarko@gmail.com>
