Add an implicit self-provide to kmods. apk can't handle self provides,
be it versioned or virtual, so opt for a prefix and a suffix instead.
Package name without a prefix/suffix is too generic and might conflict
with other packages, e.g. wireguard. This allows several variants to
provide the same virtual package without adding extra provides to the
default one, e.g. r8169 implicitly provides kmod-r8169-any and is marked
as default, so r8125 can explicitly provide @kmod-r8169-any as well.
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/21288
Signed-off-by: Robert Marko <robimarko@gmail.com>
Allow defining virtual provides using the PROVIDES field by prefixing
them with @, e.g.:
PROVIDES:=@ca-certs
Virtual provides don't own the provided name and multiple packages with
the same virtual provides can be installed side-by-side. Packages must
still take care not to override each other's files.
Add an implicit self-provide to packages. apk can't handle self
provides, be it versioned or virtual, so opt for a suffix instead. This
allows several variants to provide the same virtual package without
adding extra provides to the default one, e.g. wget implicitly provides
wget-any and is marked as default, so wget-ssl can explicitly provide
@wget-any as well.
Filter out virtual provides when generating metadata.
Filter out virtual provides prefix and self provide where appropriate.
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/21288
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refactor provides logic into a helper define and use it for both apk and
control. Document the behavior.
Store preformatted provides in Package/$(1)/PROVIDES similar to defines.
Remove unnecessary logging.
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/21288
Signed-off-by: Robert Marko <robimarko@gmail.com>
Set SND_SOC_NAU8325 to no
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/21329
Signed-off-by: Robert Marko <robimarko@gmail.com>
The SUPPORTED_DEVICES sets for both Maxlinear (v1) and Airoha (v2)
devices were identical, so sysupgrade was unable to detect when an
incorrect image was being installed. This caused "soft bricking" of
devices when a v1 image was installed on a v2 device, and vice versa.
Fix this by making the supported_devices distinct for each device
version, by renaming the devices with a version-specific name.
This is reflected in the file name and the image metadata.
Fixes: https://github.com/openwrt/openwrt/issues/20566
Fixes: https://github.com/openwrt/asu/issues/1525
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20632
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This allows us to use the full size of nand,
which extends ubi size from 64Mb to 122.25Mb.
If you are at factory firmware, please refer
to [PR](https://github.com/openwrt/openwrt/pull/21141)
to boot into OpenWrt first.
1. Log in to the device and backup all the partitions,
especially unique `Factory` and `bdata` partitions
from System -> Backup / Flash Firmware -> Save mtdblock contents.
2. Install kmod-mtd-rw to unlock mtd partitions for writing:
```bash
apk update && apk add kmod-mtd-rw && insmod mtd-rw i_want_a_brick=1
```
3. Write new OpenWrt (U-Boot Layout) `BL2` and `FIP`:
```bash
mtd write openwrt-mediatek-filogic-cudy_wbr3000uax-v1-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cudy_wbr3000uax-v1-ubootmod-bl31-uboot.fip FIP
```
4. Set static IP on your PC: `192.168.1.254`, gateway `192.168.1.1`
5. Serve openwrt-mediatek-filogic-cudy_wbr3000uax-v1-ubootmod-initramfs-recovery.itb
using TFTP server.
6. Connect Router LAN with PC LAN.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt initramfs recovery has booted,
clean `/dev/mtd5` ubi partition to utilize maximum of free space & create ubootenvs:
```bash
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
```
4. Perform sysupgrade.
Tested-by: 4pda users
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21225
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Another OEM variation of a Cudy WR3000 series device made for Russian market.
Hardware:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB GigaDevice SPI NAND. Flash Model: F50L1G41LB, ID: C801
- RAM: DDR3, 512 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- 1x WAN MT7531 (JXD 2531Z) 10/100/1000 Mbps
- 4x LAN 2x MT7530 (JXD 2529S) 10/100/1000 Mbps
- USB 3.0 port
- Buttons: Reset, WPS
- 8x LEDs: 2x Red, 6x Blue
- Serial console: no need to solder, just open the case and unskrew the radiator, TX-RX, RX-TX, GND-GND, VCC do not connect, 115200 8n1
- Power: 12 VDC, 1.5 A
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:AF:CA:xx:xx:x1 | label+1 |
| LAN | 80:AF:CA:xx:xx:x0 | label |
| WLAN 2g | 80:AF:CA:xx:xx:x0 | label |
| WLAN 5g | 82:AF:CA:xx:xx:x1 | label+1 |
+---------+-------------------+-----------+
Based on a factory layout with only 64mb partition for easier transition from factory to OpenWrt for users if the "intermediate" RSA signed firmware will be provided by Cudy.
**Installation**
The installation must be done via UART & TFTP by disassembling the router. On other occasions Cudy has distributed intermediate firmware and dts to make installation easier, but since this router is OEM special WB order for local RU market there is a possibility they will not provide it.
**Install using UART & TFTP**
1. Connect to UART.
2. Since the factory BL is locked and the boot process can not be stopped, you have to use mtkuartboot, hold reset, engage the power, boot into your payloaded bl2 & fip.
3. Connect to LAN and set your IP to 192.168.1.254.
4. Configure a TFTP server to serve openwrt-mediatek-filogic-cudy_wbr3000uax-v1-initramfs-kernel.bin file.
5. Run these steps in u-boot using the name of your file:
```
setenv bootfile openwrt-mediatek-filogic-cudy_wbr3000uax-v1-initramfs-kernel.bin
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.254
tftpboot
bootm
```
6. Router will boot into OpenWrt initramfs recovery, just open your browser `192.168.1.1` and sysupgrade with the `Keep settings` option turned off.
Tested-by: many 4pda users
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21225
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since there are many similar devices from Cudy (TR3000 / WR3000E / WR3000P / WR3000S / WBR3000UAX) this will allow to create OpenWrt U-Boot layout for all of them using same DDR3 target.
Tested-by: 4pda users
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21225
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Wifi on the 6GHz band does not support open networks, configure owe by
default. 6GHz wifi also needs a country code, configure a broken country
code '00' by default to hint the user to change it.
Link: https://github.com/openwrt/openwrt/pull/21313
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- Changing return type from void to int
- Returning error code instead of void on superio_enter() failure
- Returning 0 on success
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/21218
Signed-off-by: Robert Marko <robimarko@gmail.com>
Without this patch, the
if (!config.wpa)
config.wpa_pairwise = null;
is overwritten immediately.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Link: https://github.com/openwrt/openwrt/pull/21215
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for the Cisco Meraki MR20/Go GR10.
The Meraki MR20 is a Cisco 802.11ac/WiFi 5 AP with 1 Ethernet port.
It can be powered by a 12V DC barrel jack (5.5x2.5mm, center positive)
or via 802.3af POE.
The Meraki Go GR10 (codename: Maggot) is identical to the MR20
(codename: Grub), so this document will refer to both devices as the MR20.
MR20 hardware info:
* CPU: Qualcomm IPQ4029
* RAM: 256MB DDR3
* Storage: 128 MB (MX30LF1G18AC)
* Networking: 1 Gigabit Ethernet
* WiFi: QCA4019 802.11b/g/n/ac
* Serial: Internal header (J10, 2.54mm, unpopulated)
This device ships with secure boot, and cannot be flashed without
external programmers (TSOP48 NAND and I2C EEEPROM)!
Disassembly:
Remove the four rubber feet on the rear of the AP and the four
Torx T8 screws under the feet.
Using a guitar pick or similar plastic tool, insert it on the side
along the seam around the edge. Push in gently while gently lifting
the front of the housing to release the plastic retention clips.
There are 15 clips in total.
Once you have removed the plastic front (shown above already removed
so you know where the clips are), remove the 4 Philips screws holding
down the two metal WiFi antennas.
Lift the PCB gently while pushing the Ethernet port into the housing
to release it. The PCB should come free from the metal heat spreader.
The TSOP48 NAND flash (U9, Macronix/MXIC MX30LF1G18AC) is located on
the opposite side of the PCB.
To flash, you need to desolder the TSOP48 or use a 360 clip.
You also need to reprogram the I2C EEPROM (U20, Atmel 24c64).
Installation:
The dumps to flash can be found in this repository:
https://github.com/halmartin/meraki-openwrt-docs/tree/main/mr20_gr10
The device has the following flash layout (offsets with OOB data):
```
0x000000000000-0x000000100000 : "sbl1"
0x000000100000-0x000000200000 : "mibib"
0x000000200000-0x000000300000 : "bootconfig"
0x000000300000-0x000000400000 : "qsee"
0x000000400000-0x000000500000 : "qsee_alt"
0x000000500000-0x000000580000 : "cdt"
0x000000580000-0x000000600000 : "cdt_alt"
0x000000600000-0x000000680000 : "ddrparams"
0x000000700000-0x000000900000 : "u-boot"
0x000000900000-0x000000b00000 : "u-boot-backup"
0x000000b00000-0x000000b80000 : "ART"
0x000000c00000-0x000007c00000 : "ubi"
```
* Dump your original NAND (if using nanddump, include OOB data).
* Decompress `u-boot.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `u-boot` portion of NAND from
`0x738000`-`0x948000` (length `0x210000`). Offsets here include OOB data.
* Decompress `ubi.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `ubi` portion of NAND from
`0xc60000`-`0x8400000` (length `0x77a0000`). Offsets here include OOB data.
* Dump your original EEPROM. Change the byte at offset `0x49` to `0x1e`
(originally `0x2c` or `0x25`). Remember to re-write the EEPROM with the
modified data.
* This can be done on Linux via the following command:
`printf "\x1e" | dd of=/tmp/eeprom.bin bs=1 seek=$((0x49)) conv=notrunc`
**Note**: the device will not boot if you modify the board major number and
have not yet overwritten the `ubi` and `u-boot` regions of NAND.
* Resolder the NAND after overwriting the `u-boot` and `ubi` regions.
OpenWrt Installation:
* After flashing NAND and EEPROM with external programmers. Plug in an
Ethernet cable and power up the device.
* The new U-Boot build uses the space character `" "` (without quotes) to
interrupt boot.
* Interrupt U-Boot and `tftpboot` the OpenWrt initramfs image from your
tftp server
```
dhcp
setenv serverip <your_tftp>
tftpboot openwrt-ipq40xx-generic-meraki_mr20-initramfs-uImage.itb
```
* Once booted into the OpenWrt initramfs, created the `ART` ubivol with
the WiFi radio calibration from the mtd partition:
```
cat /dev/mtd10 > /tmp/ART.bin
ubiupdatevol /dev/ubi0_1 /tmp/ART.bin
```
* `scp` the `sysupgrade` image to
the device and run the normal `sysupgrade` procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_mr20-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_mr20-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20646
Signed-off-by: Robert Marko <robimarko@gmail.com>
qcom-ipq4029-insect-common.dtsi was common to the MR33 and MR74, but was no
longer common with the other supported Meraki devices. I have refactored
insect-common and wired-qca-common into qcom-ipq4029-meraki-common.dtsi
which contains the actual common components (e.g. NAND partitions, ART nvmem).
Individual devices reference qcom-ipq4029-meraki-insect.dtsi
plus their own individual configuration.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20646
Signed-off-by: Robert Marko <robimarko@gmail.com>
The SerDes mode setting at the end of rtpcs_931x_setup_serdes is
currently broken although it is mostly similar to what the SDK does [1].
It prevents several modes from being set, especially fiber modes. This
seems to be one (if not the only) issue for currently missing SFP
support.
Add a small helper function which takes cares of setting the mode, to
keep the still valid different procedure when using XSGMII mode. Only
this helper is called in rtpcs_931x_setup_serdes to keep it clean there.
As a functional change, call mode application in every case, not just
for SGMII, QSGMII and USXGMII. We can assume the SDK is misleading in
this case, either accidentially or on purpose. This makes SFP modules
work in theory. In practice, there still seem to be device-specific
issues which need to be fixed later. These issues may include no link
detection or link flapping.
[1] f7f85ffc14/sources/rtk-dms1250/src/dal/mango/dal_mango_construct.c (L2266)
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20736
Signed-off-by: Robert Marko <robimarko@gmail.com>
The SDK and our code for finally applying the hardware mode are quite
confusing. There are two different "places" where a mode can be set,
in a SerDes register and in a global SerDes mode register. Neither the
SDK nor any of the datasheet/documentation serve any explanation for
that. The functions are just named "fiber_mode_set" and "mii_mode_set"
which is basically as useless as it can be to understand it.
Try to get rid off this confusion by naming the functions
'sds_set_mac_mode' and 'sds_set_ip_mode' to make clear where the mode
is set. While at it, also clarify the naming of 'config_mode' by
renaming it to 'config_hw_mode'.
The naming is based on the following assumption:
> Realtek uses an SerDes IP core design (probably from another vendor)
> in their switch. This supports a variety of modes and must be
> configured properly for each mode. Usually, changing the mode in the
> MAC's registers triggers a proper configuration of the SerDes IP block
> in the background.
> However, for some modes this seems to be incomplete, at least missing
> important parts so it doesn't work on its own in the end. In this
> case, the SerDes IP block needs to be configured manually with the
> missing bits to make it work.
There are several places in the SDK that support this assumption, both
for RTL931X and RTL930X (as they are somewhat similar), e.g. [1].
[1] f7f85ffc14/sources/rtk-dms1250/src/dal/longan/dal_longan_sds.c (L1746)
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20736
Signed-off-by: Robert Marko <robimarko@gmail.com>
Improve the current mode setting functions to address a few issues:
- add missing mode from SDK reference (instead of using the
corresponding value as a default value)
- use and return error values
- give internal variable a more meaningful name
- consistently use lowercase letters in hex values
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20736
Signed-off-by: Robert Marko <robimarko@gmail.com>
Merge the unused helper 'rtpcs_931x_sds_fiber_disable' into Fiber mode
setting, and drop the helper itself. As with the MII helper in a
previous commit, functionality is basically the same just with a value
for OFF mode. If functionality is required later, Fiber mode setting can
be used with the OFF mode instead of carrying the unused helper until
it's used.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20736
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the hardware mode instead of PHY_INTERFACE_MODE_* mode for mode
setting. Adjust all affected functions and switch cases accordingly.
In MII mode setting, drop the case for 2500Base-X as this is a mistake.
In the SDK reference code, this doesn't exist [1].
[1] 69d2890a2e/sources/rtk-dms1250/src/hal/phy/phy_rtl9310.c (L817)
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20736
Signed-off-by: Robert Marko <robimarko@gmail.com>
Merge the 'rtpcs_931x_sds_disable' helper into the MII mode setting and
use that instead. The helper was essentially doing same just with a
value for OFF state.
Moreover, the name of the helper was confusing. It implied it disables
the whole SerDes. However, this is used in Fiber mode setting and thus,
cannot completely disable the SerDes.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20736
Signed-off-by: Robert Marko <robimarko@gmail.com>
The function 'rtpcs_931x_sds_mii_mode_set' does not correctly write the
register. It just write a plain value at the determined register
address. While this works for SerDes with (id mod 4 == 0), it doesn't
for the other SerDes.
Fix that by using a corresponding shift and writing only some bits
instead of the whole register.
While at it, drop an unneeded blank line, add comment to explain a bit
that is set and use the BIT(..) helper for that instead of manual shift.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20736
Signed-off-by: Robert Marko <robimarko@gmail.com>
Bring the RTL931X functions into a proper order for two purposes:
- be able to reuse code
- have blocks of logically connected functions
This just moves code, no functional changes.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20736
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix the implementation to clear symbol errors. Up to now, it was barely
functional because important modes weren't handled. Add another function
(which is needed in the future anyway) and pick to missing bits from
that function into the symbol clearing function to handle the modes
1000Base-X and 10GBaseR too. All that is based on [1].
While at it, rename the function to adhere to a common naming scheme and
fix some minor style issues.
[1] 69d2890a2e/sources/rtk-dms1250/src/hal/phy/phy_rtl9310.c (L703)
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20736
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that the bus is completely configured by the dts
compatible, drop the hard coded family detection.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21274
Signed-off-by: Robert Marko <robimarko@gmail.com>
Place the reset function into the config structure.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21274
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is no need to give the mdio bus a family dependent name.
Name the bus similar to the SerDes mdio bus.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21274
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move the read/write functions to where they belong.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21274
Signed-off-by: Robert Marko <robimarko@gmail.com>
For all families the driver uses the same read/write functions.
Drop the duplicate per-family initialization.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21274
Signed-off-by: Robert Marko <robimarko@gmail.com>
Relocate the cpu port definition over to the new configuration
structure. There are several family specific places where the
driver checks port ranges. These are a wild mix of arbitrary
values (64) or constant defines. Remove them as the the central
read/write functions already have a proper check with -ENODEV
bail out in place.
With the cleanup drop the port defines as there is only one
consumer (config structure) left.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21274
Signed-off-by: Robert Marko <robimarko@gmail.com>
The mdio driver already has a family specific compatible that
is used in the dts to denote the device type. Nevertheless it
is not evaluated. The driver determines the family on its own
in rtmdio_get_family().
Break up this dependency by providing a configuration structure
that can be automatically assigned by device_get_match_data().
For now only move the rawpage variable over there.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21274
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ethernet and dsa drivers still rely on several defines from
the central mach include. Move important defines over to the
driver specific includes as a first decoupling step.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21263
Signed-off-by: Robert Marko <robimarko@gmail.com>
Changes:
* use upstream patches for airoha-snfi driver
* update in kernel en7523 dts to add spinand support
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/21299
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add dual-partition upgrade support for Qihoo 360v6 using the generic
bootconfig.sh library. This enables safe system upgrades with automatic
failover capability.
The device uses Qualcomm's bootconfig structure to control A/B partition
switching. The bootloader dynamically maps physical NAND partitions to
logical MTD devices based on the bootconfig, ensuring firmware always
writes to the inactive partition.
Implementation details:
- Use bootconfig.sh library (copied from ipq50xx) for bootconfig operations
- Operate on 'rootfs' partition by name instead of hardcoded offset
- Add magic header validation for safety
- Remove OEM UBI volumes (wifi_fw and ubi_rootfs) before sysupgrade
- Toggle bootconfig before removing OEM volumes
Hardware details:
- SoC: Qualcomm IPQ6000
- Flash: NAND with dual rootfs partitions (mtd16/mtd17)
- Bootconfig: controls slot selection via partition name lookup
Installation:
Standard sysupgrade process. After upgrade, the system will boot
from the new partition while preserving the old system as backup.
The OEM volume cleanup is necessary because these volumes are created
by the stock firmware and are not automatically cleaned by the standard
nand_upgrade_prepare_ubi() function, which only removes volumes named
'kernel', 'rootfs', and 'rootfs_data'. Without this cleanup, the remaining
OEM volumes consume available space, causing the creation of rootfs_data
to fail during sysupgrade.
Tested on Qihoo 360v6 running stock firmware and OpenWrt.
Signed-off-by: Zhenyu Qi <qzydustin@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/21154
Signed-off-by: Robert Marko <robimarko@gmail.com>
The EW71v2 has the WAN port configured at eth1.
The printed label-mac is configured on this iface in openwrt.
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
When wdev interfaces and hostapd interfaces are mixed, race conditions
can occur. Sometimes all interfaces are started correctly, sometimes only
the wdev interface and some of the hostapd interfaces, and sometimes only
the wdev interface.
Fix this by creating the wdev interfaces first, before processing
wpa_supplicant or hostapd interfaces.
Link: https://github.com/openwrt/openwrt/pull/21303
Signed-off-by: Nick Hainke <vincent@systemli.org>
RTL930x devices have highmem starting address at 0x20000000.
The Linksys LGS328C highmem definition is wrongly shared with
the larger LGS352C RTL931x model and starts at 0x90000000.
Fix it by splitting the definition.
Fixes: 853d73f ("realtek: add support for Linksys LGS328C")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit 423cda97f9.
It appears that this broke remoteproc on some devices, so revert for now.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The multicast rate (mcast_rate) is defined as a single numeric value,
not an array. The ucode scripts already expect a single number, and
the OpenWrt documentation specifies this option as an integer [0].
Adjust the wireless schema accordingly. This also fixes the wdev.uc
call path for the iw fallback mesh setup.
[0] - https://openwrt.org/docs/guide-user/network/wifi/basic
Link: https://github.com/openwrt/openwrt/pull/21291
Signed-off-by: Nick Hainke <vincent@systemli.org>
The previous wdev.uc invocation failed for mesh interfaces.
Rewrite it as a loop so the mesh interface is created correctly
when no wpa_supplicant mesh support is installed.
Link: https://github.com/openwrt/openwrt/pull/21291
Signed-off-by: Nick Hainke <vincent@systemli.org>
Hardware is identical to WRC-X3200GST3.
- SoC: MediaTek MT7622
- RAM: 512MB
- Flash: 128MB SPI-NAND
The -W suffix in the retail name (WRC-G01-W) denotes the casing color
and is omitted from the model name in the OpenWrt configuration to
maintain consistency with other Elecom devices.
Signed-off-by: Yuhei Amemiya <minihui@me.com>
Link: https://github.com/openwrt/openwrt/pull/21238
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The path to the LuCI index cache file has changed to
/tmp/luci-indexcache.*.json since OpenWrt 22.03.
Update functions.sh to align with luci.mk.
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21280
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Include XHCI USB drivers on the Cudy WR3000P v1 router, the drivers are
required to be able to use the USB port for USD devices.
Closes: https://github.com/openwrt/openwrt/issues/21231
Fixes: 04e9d154f2 ("mediatek: filogic: add support for Cudy WR3000P v1")
Signed-off-by: Dmitry Mostovoy <dmitry.mostovoy@ceifx.com>
Link: https://github.com/openwrt/openwrt/pull/21281
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This typo makes the script fail with:
-ash: /etc/hotplug.d/ieee80211/10_fix_wifi_mac: line 66: syntax error: unexpected word (expecting ")")
which ultimately prevents the mac address for certain devices wireless cards being set correctly
Signed-off-by: Nick French <nickfrench@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21287
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ipq5018 do not support freq scaling and therefore stuck on 800Mhz
This patch allows CPU to run with 1.008 Ghz as designed
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
Link: https://github.com/openwrt/openwrt/pull/21185
Signed-off-by: Robert Marko <robimarko@gmail.com>
Mesh interfaces may not define an encryption setting. This results in
a ucode runtime error when parse_encryption() is called:
Reference error: left-hand side expression is null
In parse_encryption(), file /usr/share/ucode/wifi/iface.uc, line 20, byte 32:
called from function setup_sta (/usr/share/ucode/wifi/supplicant.uc:59:31)
called from function generate (/usr/share/ucode/wifi/supplicant.uc:243:41)
called from function setup (./mac80211.sh:254:61)
called from anonymous function (./mac80211.sh:342:14)
` config.auth_type = encryption[0] ?? 'none';`
Near here ------------------------^
Link: https://github.com/openwrt/openwrt/pull/21293
Signed-off-by: Nick Hainke <vincent@systemli.org>
