Product name: Wavlink WL-WN536AX6 Rev a "Mighty LX2"
Product link: https://www.wavlink.com/en_us/product/WL-WN536AX6.html
Specifications:
SOC: MT7986AV
RAM: 512MB DDR4
Flash: 128MB SPI NAND
Ports: 4 LAN (1G) & 1 WAN (2.5G)
WIFI: MT7976PN + MT7975N
LEDs: 8 (STATUS, WIFI, WAN, LAN1, LAN2, LAN3, LAN4, PWR)
USB: 1 (3.0)
MAC table, same as stock firmware:
LAN: 80:3F:5D:xx:xx:x1 partition "hw" at 0x44e (ASCII)
WAN: 80:3F:5D:xx:xx:x2 partition "hw" at 0x460 (ASCII)
2G: 80:3F:5D:xx:xx:x3
5G: 80:3F:5D:xx:xx:x4
* Installation with OEM WebUI:
Note: Make sure PC is connected on LAN1 port. The OEM firmware has an unknown root password and settings are kept after upgrading firmware. Therefore, a customized Openwrt firmware is needed to remove the root password on login, by adding `passwd -d root` to /etc/init.d/bootcount. The WebUI does a filename check so the customized firmware is named accordingly.
1. Download modified firmware file `WAVLINK_WN536AX6-A_M36AX6_V250320-WO-437baca-modified.bin` from https://github.com/ses1er/firmware-misc/tree/main/wavlink/wl-wn536ax6a
2. Log into WebUI on default IP: http://192.168.20.1
3. Browse to More (top menu) -> System -> Firmware Upgrade.
4. Under `Local Upgrade` section, check the device to be upgraded and upload downloaded modified firmware. Click `UPLOAD FILE`, then `APPLY`
5. Wait about 2 minutes (ignore progress bar), and browse to http://192.168.20.1. You should see LUCI login page. Username is root and no password.
6. Browse to `System -> Backup/Flash Firmware`, click on `Flash Image`, click `Browse` and locate `openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin` file.
7. Uncheck `Keep settings and retain the current configuration` and click `Continue`.
8. Router will now be set to IP 192.168.1.1 which is the Openwrt default.
* Installation with UART:
Note: Having UART connected while cold booting the device will result in a kernel panic when initializing wifi. I've found this workaround:
1. Power off the device and ensure UART is not connected to PC.
2. Power up the device, when lights come on, plug in UART.
3. Warm boots and soft restarts will not cause kernel panic for the duration of device being powered on. Repeat steps for subsequent cold boots.
1. Configure TFTP server with IP 192.168.1.66. Copy `openwrt-mediatek-filogic-wavlink_wl-wn536ax6a-initramfs.itb` to TFTP root.
2. Interrupt boot by pressing 0.
3. Run the following in Uboot console: `setenv serverip 192.168.1.66; setenv ipaddr 192.168.1.1; tftpboot 0x46000000 openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-initramfs.itb; bootm`
4. Transfer `openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin` to device:
(`scp -O openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/`)
5. Run the following on device: `sysupgrade -n /tmp/openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin`
Signed-off-by: Qing W. <ses1er@gmail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/20760
(cherry picked from commit 1748ce8295)
Link: https://github.com/openwrt/openwrt/pull/20775
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware:
- SoC: MediaTek MT7621DAT
- Flash: 16 MiB XM25QH128C
- RAM: 128 MiB
- WLAN: 2.4 GHz (MT7603E, 11n), 5 GHz (MediaTek MT7613BEN, 11ac)
- Ethernet: 1x10/100/1000 Mbps LAN
- Buttons: 1 Reset button, 1 WPS button
- LEDs: 5x Green
- Serial Console: unpopulated header 115200 8n1 (silkscreen on PCB)
- Power: POE 802.3af (37-57V DC)
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label |
| WLAN 5g | 82:af:ca:xx:xx:x1 | +1 |
+---------+-------------------+-----------+
Installation:
The factory firmware is locked: you can only work with Cudy signed firmware.
Download a intermediate firmware signed by Cudy here:
https://www.cudy.com/blogs/faq/openwrt-software-download
After that, login to the router (192.168.10.254, password "admin") and install the intermediate firmware.
If you can reach LuCI or SSH now on the intermediate firmware, just use the sysupgrade image with the 'Keep settings' option turned off.
Special thanks to Daniel de Kock for starting the porting work at #16265.
Signed-off-by: Luis Mita <luis@luismita.com>
Co-Authored-By: Daniel de Kock <daniel@riot.network>
Co-Authored-By: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/20268
(cherry picked from commit 8fb644e9e8)
Link: https://github.com/openwrt/openwrt/pull/20710
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Replace hardcoded numbers with the dt-bindings drive strength macros
defined in "dt-bindings/pinctrl/mt65xx.h".
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20894
(cherry picked from commit 2c667f2df4)
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20773
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification
-------------
- SoC : MediaTek MT7986AV quad-core ARM Cortex-A53 2GHz
- RAM : DDR4 512Mbytes, Nanya Technology NT5AD256M16E4
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976DAN, MediaTek MT7916AN, MediaTek MT7976AN
- 2.4GHz : b/g/n/ax, Multi User MIMO
- 5GHz : a/n/ac/ax, Multi User MIMO
- 6GHz : ax, Multi User MIMO
- Ethernet : 10/100/1000 Mbps x4, LAN (MediaTek MT7531AE)
10/100/1000/2500 Mbps x1, WAN (MaxLinear GPY211C0VC)
- UART : 1x4 pin header on PCB
- [J1] 3.3V, TX, RX, GND (115200, 8N1)
- Buttons : WPS, Reset
- Switches : Rfkill Slide Switch
- USB : 1x USB 3.0 (MediaTek MT7986AV peripheral)
- FAN : 1x Fan (off - slow - fast)
- LEDs : 1x Power (Blue)
1x CPU (Blue)
1x Wi-Fi 6GHz (Blue)
1x Wi-Fi 5GHz (Blue)
1x Wi-Fi 2.4GHz (Blue)
4x LAN activity (Blue)
1x WAN activity (Blue)
1x USB 3.0 (Blue)
- Power : 12VDC, 3.5A (Center positive polarity)
MAC address
-----------
+-----------+-------------------+------------------------+
| Interface | MAC | Algorithm |
+-----------+-------------------+------------------------+
| WLAN 2.4G | 58:86:94:xx:xx:xx | label1 |
| WLAN 5G | 5A:86:94:xx:xx:xx | label2 with LA Bit set |
| WLAN 6G | 5A:86:94:xx:xx:xx | label1 with LA Bit set |
| WAN | 58:86:94:xx:xx:xx | label1 + 1 |
| LAN | 58:86:94:xx:xx:xx | label1 + 3 |
+-----------+-------------------+------------------------+
The WLAN 2.4G MAC address (label1) was found in 'Factory' partition, 0xA0004
The WLAN 5G MAC address (label2) was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software (ipTIME Firmware Wizard (11ac))
from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router (keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router (LAN port) to the PC
6. Run the OEM recovery software and follow the instructions
7. Select the *squashfs-factory.bin file during the router recovery process
8. Wait for the router to boot from *squashfs-factory.bin
Note: The router will automatically reboot if no file is uploaded within
55 seconds.
Fan Control
------------
The fan speed is controlled by writing a value from 0 to 2 to the
`fan1_target` file.
```
cd /sys/devices/platform/gpio-fan/hwmon/hwmon2
echo '0' > fan1_target // off
echo '1' > fan1_target // slow
echo '2' > fan1_target // fast
```
Limitation: Enabling Wi-Fi 6E
----------
Wi-Fi 6E (6GHz) does not work out of the box on LuCI.
After installation, you need to configure a few settings in the `radio1`
and `default_radio1` sections of the `/etc/config/wireless`.
Once you have made these changes, you can enable and use Wi-Fi 6E.
In the `radio1` section, you need to add three common options:
- band: must be set to `6g`
- country: a valid country code for the 6GHz band
- channel: a preferrend scanning channel (PSC) for 6GHz
In the `default_radio1` section, you need to add the SSID and key:
- ssid: The public name of your Wi-Fi network
- key: The Wi-Fi password
- encryption: must be set to either `sae` for WPA3 or `owe` for OWE
(open network)
Example:
```
config wifi-device 'radio1'
...
option band '6g'
option country 'KR'
option channel '37'
...
config wifi-iface 'default_radio1'
...
option ssid 'my_wifi_6e_name'
option key 'my_strong_password1234'
option encryption 'sae'
...
```
Note: A list of all the 6GHz PSC channels:
```
5, 21, 37, 53, 69, 85, 101, 117, 133, 149, 165, 181, 197, 213, and 229
```
Limitation: Maximum Transmit Power (Wi-Fi 6E)
----------
The maximum transmit power is currently broken. In the drop-down menu,
you can only choose between "driver default" and "255 dBm (2147493647
mW)". There is currently no workaround for the issue. Please leave the
maximum transmit power set to "driver default".
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19763
(cherry picked from commit 2503e5bc37)
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20773
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
MediaTek MT7981 WiSoC
512MB DDR4 RAM
128MB SPI-NAND
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
4 LAN MediaTek MT7531 PHY
1 WAN RTL8221B-VB-CG 2.5Gbps PHY
UART: 115200 8N1 3.3V
USB2 Port
PoE on WAN Port
MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set
Gotchas:
WAN LED does not light up (might require further DTS tweaks)
PoE on WAN port was not tested
This commit is heavily based on WR3000H one, I've just ported DTS differences
from the official image to get USB support and proper LED mapping.
Installation
------------
[Untested as I've received and used a transitional image from Cudy]
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device + press reset pin. Keep pressing reset pin to enter the U-Boot shell.
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.88. Rename the image to "cudy3000p.bin"
4. Download and boot the OpenWrt initramfs image.
$ tftpboot 0x46000000 cudy3000s.bin; bootm 0x46000000
5. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Signed-off-by: Michal Halva <hedik01@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19636
(cherry picked from commit 04e9d154f2)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Link: https://github.com/openwrt/openwrt/pull/20830
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes the "mdio_bus stmmac-1: MDIO device at address 1 is missing" error
that occurs during cold boot when initializing GMAC.
Fixes: 8ca4caacd0 ("rockchip: Add support for RK3568 LinkEase EasePi R1")
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20772
(cherry picked from commit e6a5ca0da7)
Link: https://github.com/openwrt/openwrt/pull/20744
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The generic-rk3568 does not reset the gmac phy, causing the kernel to
fail to initialize gmac during cold boot with the error message
"mdio_bus stmmac-1: MDIO device at address 1 is missing."
Adding a dedicated uboot for EasePi R1 to resolve this issue.
The EasePi R1's DTS hasn't been merged into the Linux release yet,
so it cannot be submitted to the upstream u-boot.
Fixes: ef093299db ("uboot-rockchip: add support for LinkEase EasePi R1")
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20772
(cherry picked from commit 5dff7b45d3)
With changes:
1. Reorder patch file names (`105-*` to `106-*`).
2. configs/easepi-r1-rk3568_defconfig needs CONFIG_SPL_PAD_TO on u-boot 2024.10.
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20744
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The probe order for PCIe buses and devices is non-deterministic,
making the names eth2 and eth3 unpredictable (they may be swapped).
This patch fixes the names by referencing the device path using
`ucidef_set_network_device_path`.
This patch ensures that the OpenWrt interface name matches the case label.
Fixes: 8ca4caacd0 ("rockchip: Add support for RK3568 LinkEase EasePi R1")
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20779
(cherry picked from commit d7530c1e54)
Link: https://github.com/openwrt/openwrt/pull/20744
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for esmt F50L1G41LC flash chip. It is used in some recent
Cudy devices.
(cherry picked from commit c84025dea2)
Link: https://github.com/openwrt/openwrt/pull/20963
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport upstream patch to add support for the ESMT F50L1G41LC flash
chip. It is used in multiple Cudy products manufactured starting
November 2025.
(cherry picked from commit 9424b2b786)
Link: https://github.com/openwrt/openwrt/pull/20963
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In implementing APK support it seems a a leftover was never removed that
creates an unused tmp directory in the package feed directory.
Drop it as it's not used anywhere. What is actually needed is the
creation of the $$(PDIR_$(1)) directory for the feed package directory
in the bin/packages directory.
This was a side effect of using INSTALL_DIR on $$(PDIR_$(1))/tmp that
indirectly creates the $$(PDIR_$(1)) parent directory.
Fixes: d788ab376f ("build: add APK package build capabilities")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit f9802d70c6)
Airoha AN7581 SoC supports a Network Processor (NPU) to offload WiFi
traffic. Add the required bits to enable the support of it in the MT76
driver. This will be enabled by default if we are compiling for the
Airoha AN7581 SoC.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
[ improve commit title/description ]
Link: https://github.com/openwrt/openwrt/pull/20826
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 79d418eed8)
0aece3089a3a wifi: mt76: mt7996: Remove useless check in mt7996_msdu_page_get_from_cache()
05b3d899ad24 wifi: mt76: Move Q_READ/Q_WRITE definitions in dma.h
85e6517b0ac5 wifi: mt76: Add mt76_dev pointer in mt76_queue struct.
a3b6c67c97d2 wifi: mt76: Add the capability to set TX token start ID
141a81557070 wifi: mt76: Introduce the NPU generic layer
647d11bb17e0 wifi: mt76: mt7996: Add NPU offload support to MT7996 driver
8ff3b2bfc37f wifi: mt76: mt7996: fix typos in comments
0043147439b4 wifi: mt76: mt7925: refactor regulatory domain handling to regd.[ch]
f0e8fe441489 wifi: mt76: mt7925: refactor CLC support check flow
588cc87bf6a2 wifi: mt76: mt7925: refactor regulatory notifier flow
dac1d45fe94b wifi: mt76: mt7925: improve EHT capability control in regulatory flow
c166c4a0e750 wifi: mt76: mt7925: add auto regdomain switch support
d7b059bba166 wifi: mt76: mt7925: disable auto regd changes after user set
84f62a6beb99 wifi: mt76: mmio_*_copy fix byte order and alignment
f5ae5b2e8116 Revert "wifi: mt76: mt792x: improve monitor interface handling"
8ae7e6dc1d3a wifi: mt76: adjust BSS conf pointer handling
1b438ebe0d06 wifi: mt76: mt7925: cqm rssi low/high event notify
7519fa4ce62c wifi: mt76: mt7996: fix max nss value when getting rx chainmask
ea0580ad065f wifi: mt76: mt7996: no need to wait ACK event for SDO command
74112c2956fb wifi: mt76: mt7996: fix implicit beamforming support for mt7992
361d6bdac45d wifi: mt76: mt7996: support fixed rate for link station
d99274cdc30c wifi: mt76: mt7996: fix several fields in mt7996_mcu_bss_basic_tlv()
ad90a85b652b wifi: mt76: mt7996: fix teardown command for an MLD peer
e9fe8bc03e41 wifi: mt76: mt7996: set link_valid field when initializing wcid
050394665502 wifi: mt76: mt7996: use correct link_id when filling TXD and TXP
5d223855552c wifi: mt76: mt7996: fix MLD group index assignment
ab8361dbc421 wifi: mt76: mt7996: fix MLO set key and group key issues
7ce7ab881b3f wifi: mt76: mt7996: fix using wrong phy to start in mt7996_mac_restart()
1e0c23ff754b wifi: mt76: mt7996: fix EMI rings for RRO
eb567bc7f9b6 wifi: mt76: mt7925: ensure the 6GHz A-MPDU density cap from the hardware.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit e1a584b5d2)
Some Marvell AP firmware used with mwl8k misbehaves when beacons do not
contain the DSSS Parameter Set (WLAN_EID_DS_PARAMS) with the current
channel. When hostapd/mac80211 omits this element (which is valid on
some bands), the firmware may report bogus RX channel information and AP
mode becomes unusable.
Backport the upstream fix that ensures beacons always carry the DSSS
Parameter Set for mwl8k: when setting the beacon, detect if the element
is missing and inject it after SSID and Supported Rates (per spec
ordering). This mirrors behaviour in newer Marvell drivers and restores
stable operation.
Tested on Linksys EA4500 (88W8366).
Fixes: openwrt/openwrt#19088
Link: https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless.git/commit/?id=c4e1ac09ee1c750890e36cb1f841f25518f23589
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20757
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 38ed1510db)
[refreshed patches]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20817
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Since we are not using patch -b, *.orig files are only created when
there are conflicts, or never according to posix patch.
As such, it doesn't really make sense to always delete *.orig files
presuming they are patch backups, even if they are patch backups.
Doing so is both deleting potentially useful information for failed
patch applications and creating hard to diagnose bugs [1].
In a similar vein, checking for *.rej files does not add any value
since we're already checking the patch command's return code.
[1]: https://github.com/openwrt/packages/issues/27485
Signed-off-by: George Tsiamasiotis <george@tsiamasiotis.gr>
Link: https://github.com/openwrt/openwrt/pull/20141
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 75ca6bafd6)
Link: https://github.com/openwrt/openwrt/pull/20742
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
When building in environments that set IS_TTY, the feeds script does not
honor it and passes a hardcoded value to scan.mk, causing unwanted
control characters to appear in stdout.
This commit addresses the issue by checking IS_TTY and MAKE_TERMOUT
variables and uses their values if defined.
Closes#8039
Signed-off-by: Ernestas Kulik <ernestas.k@iconn-networks.com>
Link: https://github.com/openwrt/openwrt/pull/20743
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit fd7e43d429)
Backport upstream patch fixing out of order DMA access for ethernet
driver. This is relevant in the context of QoS when packets doesn't
follow linear handling by QDMA HW.
(cherry picked from commit 3169ffa4c7)
[ fix conflict errors ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
A new function "get_linux_version()" to normalize and print the
kernel version as an integer. In some migration scripts, it is
useful for checking the Linux kernel version.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit a0fe3cfb62)
Link: https://github.com/openwrt/openwrt/pull/20739
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
KConfig flag have an extra whitespace for CONFIG_PHY_AIROHA_USB and
value is not ignored.
Drop the extra whitespace to correctly ignore the value on kernel
compilation.
Fixes: c5b12fc02a ("airoha: Introduce support for Airoha AN7583 SoC")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit eedc7b3b79)
Replace Airoha AN7581 PWM patch with upstream version and add kernel
version tag.
(cherry picked from commit 2352de96c1)
[ fix conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport upstream minor fixed for NPU handling that might result in
kernel panic or handle leak.
(cherry picked from commit 83eacb6ab0)
[ fix conflict errors ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add missing leds and network board files for EN7581 SoC.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
[ drop reference to downstream 10g RFB board ]
Link: https://github.com/openwrt/openwrt/pull/20556
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 738eacb9a0)
Similar to e92b153e99 ("mediatek: introduce KERNEL_LOADADDR to Device/Default template"),
let's move the default loadaddr to Device/Default.
What's more, use 0x80200000 instead of the SDK default value 0x80088000
to avoid the following error which may overwrite TZ memory and cause crash:
[ 0.000000] [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader!
[ 0.000000] OF: reserved mem: Reserved memory: failed to reserve memory for node 'atf@80000000': base 0x0000000080000000, size 2 MiB
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
[ fix spelling mistake ]
Link: https://github.com/openwrt/openwrt/pull/20470
(cherry picked from commit fed2d31343)
[ fix conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Enable USB node on eMMC RFB board and disable USB2 3.0 port to make the
3rd PCIe line correctly work.
This is needed to prevent the xHCI driver to mess with PCIe by
configuring the USB2 3.0 port. Port will still be detected but won't be
configureed by the driver and won't have PHY to configure for.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 6d51c80424)
The 3rd PCIe line use the USB2 serdes for PCIe operation. Correctly set
it to the DT node so that the mode can be correctly set in the PHY
driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3ba92e0e32)
Add pending patch for USB support on AN7581 SoC. This is also required
to make operational the 3rd PCIe line that use the USB2 Serdes for PCIe
operations.
(cherry picked from commit 7afc2da3fc)
[ fix conflict errors, add missing Kconfig flag ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some SoC might use the Serdes for the second USB port as a 3rd PCIe
line (with the SSTR register correctly setup).
Add the node for the 3rd PCIe card and enable for the eMMC RFB board.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 2fae199953)
Backport a patch fixing a kernel panic on airoha_hw_init fail. This
should better handle scenario with NPU load Probe deferring.
(cherry picked from commit c3c75d0e68)
[ fix conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport cleanup patch for Airoha Ethernet patch to permit easier
backport in the future.
Automatically refresh all affected patch.
(cherry picked from commit 2f3ea18f91)
[ fix conflict errors, drop upstream patch ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Airoha AN7581 eMMC RFB board mount 2 Aeonsemi AS21xxx PHY. One is
usually connected to GDM4 and the other is optionally connected to GDM2.
Add the relevant nodes to support the one connected to GDM4.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 26da4bf552)
Pack the BL2 and BL31+U-Boot artifacts as Airoha AN7581 is currently
supported in upstream U-Boot and bootloader files can be used for
unfused boards.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 17cb69fe7f)
Backport additional patch required for NPU support of Airoha AN7583.
These are specific for the NPU module with some minor fixes and to adds
upport for loading the specific Airoha AN7583 NPU firmware.
(cherry picked from commit 8b4adfbb87)
[ fix conflict errors ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add relevant nodes for NPU support for Airoha AN7583 and enable the
kernel config to enable support in the Airoha Ethernet driver.
NPU firmware is scheduled to be upstreamed to linux-firmware and will be
added once present upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 8758b58f25)
Fix the current image Makefile for Airoha AN7583 by dropping the
artifacts entry for bootloader and add default PKG for the PHY mounted
on the RFB boards.
The artifacts for the bootloader will be readded later once ATF-A
support will be pushed mainline.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a7964f0893)
While adding support for Airoha AN7583, it was forget to push the EMMC
DTS while defining the variant in the image Makefile.
Add the missing DTS to fix image creation error.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 6fe65d404b)
