Backport support for Aeonsemi AS121xxx PHY. The PHY require dedicated
firmware to be loaded to correctly work and support a big family of
Aeonsemi PHY that provide from 1G to 10G speed.
Automatically refresh all affected patch and file (rtl PHY).
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Import upstream patches fixing issues with unreliable temperature
reading on some batches of the MediaTek MT7988 SoCs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use macro defined bias types instead of some magic numbers. This can
help reviewers better understand bias types.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19855
Signed-off-by: Robert Marko <robimarko@gmail.com>
The kmod is installed on all filogic mediatek images, even for devices
that do not have any aquantia hardware. Remove it.
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19488
[Do not explicitly remove kmod-phy-aquantia from gatonetworks_gdsp]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for the WAVLINK WL-WN586X3 Rev B, which swaps
the 16MB NOR flash for an 128MB NAND flash chip, and uses UBI for
data partition. This commit utilizes the previous submitted dtsi that
includes common hardware for a few Wavlink routers.
Hardware
--------
- SOC: MediaTek MT7981B
- RAM: 256MB DDR3
- Flash: 128MB SPI-NAND (ESMT F50L1G41LB)
- Ethernet: 2x1Gb Lan 1x1Gb Wan
- WiFi: MediaTek MT7981B 2x2 DBDC 802.11ax 2T2R (2.4/5) with 4 external and 1 internal antennae
- LEDs: 2xLan 1x Wan 1x WIFI 1xSTATUS
Installation
------------
Flashing over the vendor WebUI has been tested and unsuccessful (YMMV).
The image need to be flashed via TFTP which can be activated over the onboard UART serial console:
1. Connect UART: TX->board RX, RX->board TX, GND->board GND.
2. Connect PC to router lan port.
3. Setup the tftp server on PC, set IP to 192.168.10.100.
4. Power on the device. Interrupt boot countdown at uboot boot menu and select 2. Upgrade firmware option.
5. Input the image name and start flashing.
Sample uboot menu:
```
*** U-Boot Boot Menu ***
1. Startup system (Default)
2. Upgrade firmware
3. Upgrade ATF BL2
4. Upgrade ATF FIP
5. Upgrade single image
6. Load image
0. U-Boot console
```
NOTE: Do not use the intermediate image here which is for Rev A only:
https://github.com/themaverickdm/firmware-misc/tree/main/wavlink/wl-wn586x3
MAC Addresses
-------------
LAN: 80:3F:5D:xx:xx:x1 (hw, 0x44e, ASCII encoded)
WAN: 80:3F:5D:xx:xx:x2 (hw, 0x460, ASCII encoded)
2G: 80:3F:5D:xx:xx:x3 (factory, 0x4, raw binary, also on label)
5G: 80:3F:5D:xx:xx:x3 (Same as 2G)
Signed-off-by: Zhenfu Shi <i0ntempest@i0ntempest.com>
Link: https://github.com/openwrt/openwrt/pull/19785
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
mt7531 switch reset delay time is hard coded in the driver. The
"reset-assert-us" and "reset-deassert-us" won't take effect.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19741
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use tabs to align and remove some unnecessary spaces.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19741
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
They were lost when ported to the 6.12 kernel.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19741
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Mediatek pinctrl driver can only accepts drive-strength values
enumerated in "dt-bindings/pinctrl/mt65xx.h".
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19741
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the missing "device_type" property to fix the memory node. The
Linux kernel can not get the memory size without it. Though u-boot
can automatically fixup the memory node by adding the "device_type"
and "reg" properties if the CONFIG_ARCH_FIXUP_FDT_MEMORY symbol is
enabled, it's better not to rely on this optional feature. This
patch also adds the reg address for the memory node name to follow
the naming rules.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19741
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Product name: Acer Predator Connect W6x
Product link: https://www.acer.com/us-en/predator/networking/wi-fi/predator-connect-w6x/pdp/FF.G2TTA.001
* Specifications:
SOC: MT7986AV
RAM: 1024MB
Flash: 256 MB SPI NAND
Ports: 4 LAN (1G) & 1 WAN (2.5G)
WIFI: MT7976GN + MT7976AN
LED: 1, ws2812b controller
* Installation via UART:
1. Configure TFTP server with IP 192.168.1.66. Copy `openwrt-mediatek-filogic-acer_predator-w6x-initramfs-kernel.bin` to TFTP root and rename to `predator.bin`
2. Interrupt boot by pressing 0 on startup or select `U-Boot Console` in U-Boot Boot Menu.
3. Run setenv `serverip 192.168.1.66; setenv ipaddr 192.168.1.1; tftpboot 0x46000000 predator.bin; fdt addr $(fdtcontroladdr); fdt rm /signature; bootm` in uboot console.
4. Wait for boot complete on Openwrt initramfs env.
** You can back up the MTD partitions at this point. Refer to Backup Instructions section.
5. On client PC, transfer `openwrt-mediatek-filogic-acer_predator-w6x-squashfs-sysupgrade.bin` to /tmp/ - `scp -O openwrt-mediatek-filogic-acer_predator-w6x-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/sysupgrade.bin`
6. On router, run sysupgrade - `sysupgrade -n /tmp/sysupgrade.bin`
Should now boot to Openwrt. Ensure it boots automatically to Openwrt by replugging the power.
* Backup Instructions:
Layout from stock firmware:
```
[ 0.968731] Creating 10 MTD partitions on "nmbm_spim_nand":
[ 0.974297] 0x000000000000-0x000000100000 : "BL2"
[ 0.979424] 0x000000100000-0x000000180000 : "u-boot-env"
[ 0.985032] 0x000000180000-0x000000380000 : "Factory"
[ 0.990379] 0x000000380000-0x000000580000 : "FIP"
[ 0.995378] 0x000000580000-0x000000600000 : "prod"
[ 1.000461] 0x000000600000-0x000000700000 : "dual"
[ 1.005527] 0x000000700000-0x000000800000 : "pot"
[ 1.010516] 0x000000800000-0x000006c00000 : "ubi"
[ 1.015626] 0x000006c00000-0x00000d000000 : "ubi1"
[ 1.020801] 0x00000d000000-0x00000d800000 : "storage"
```
Mapping in initramfs env:
```
dev: size erasesize name
mtd0: 00100000 00020000 "bl2"
mtd1: 00080000 00020000 "u-boot-env"
mtd2: 00200000 00020000 "factory"
mtd3: 00200000 00020000 "fip"
mtd4: 00020000 00020000 "prod"
mtd5: 00100000 00020000 "dual"
mtd6: 00100000 00020000 "pot"
mtd7: 06400000 00020000 "ubi"
mtd8: 06400000 00020000 "ubi1"
mtd9: 00800000 00020000 "storage"
```
1. While in openwrt initramfs environment, back up all the partitions by running the following:
```
cat /dev/mtd0 > /tmp/bl2.bin
cat /dev/mtd1 > /tmp/u-boot-env.bin
cat /dev/mtd2 > /tmp/factgory.bin
cat /dev/mtd3 > /tmp/fip.bin
cat /dev/mtd4 > /tmp/prod.bin
cat /dev/mtd5 > /tmp/dual.bin
cat /dev/mtd6 > /tmp/pot.bin
cat /dev/mtd7 > /tmp/ubi.bin
cat /dev/mtd8 > /tmp/ubi1.bin
cat /dev/mtd9 > /tmp/storage.bin
```
2. Transfer files to client PC for safekeeping. On client PC, run `scp -O root@192.168.1.1:/tmp/*.bin ./`
* Restore to Stock Firmware:
1. Boot to openwrt initramfs env.
2. Confirm layout matches as follows by running `cat /proc/mtd`. Ensure dev `mtd7` is named `ubi`:
```
dev: size erasesize name
mtd0: 00100000 00020000 "bl2"
mtd1: 00080000 00020000 "u-boot-env"
mtd2: 00200000 00020000 "factory"
mtd3: 00200000 00020000 "fip"
mtd4: 00020000 00020000 "prod"
mtd5: 00100000 00020000 "dual"
mtd6: 00100000 00020000 "pot"
mtd7: 06400000 00020000 "ubi"
mtd8: 06400000 00020000 "ubi1"
mtd9: 00800000 00020000 "storage"
```
3. Detach `ubi` partition - `ubidetach -p /dev/mtd7`
4. Transfer stock firmware's `ubi.bin` to router from client PC: `scp -O ubi.bin root@192.168.1.1/tmp/`
5. Format and replace with backup `ubiformat /dev/mtd7 -y -f /tmp/ubi.bin`
6. Reboot and you should now be back on stock firmware.
* LEDS:
LED color can be controlled by specifying values in GRB format in `/sys/class/leds/rgb:status/multi_intensity`. Default is `255 255 255` (white).
Example: `echo '75 0 130' > /sys/class/leds/rgb:status/multi_intensity`
LED brightness can be changed by specifying the value from 0-255 in /sys/class/leds/rgb:status/brightness. Default is `255` (full brightness).
Example: `echo 100 > /sys/class/leds/rgb:status/brightness`
For persistence across reboots, put the relevant command(s) in /etc/rc.local.
* Notes:
root access on stock firmware:
Before flashing openwrt, and while in openwrt initramfs env:
1. Mount /dev/ubi0_2: `mkdir /tmp/ubi0_2; mount -t ubifs /dev/ubi0_2 /tmp/ubi0_2`
2. Modify `/tmp/ubi0_2/upper/etc/passwd` and change line with `root❌0:0...` to `root::0:0...`, remove the `x`.
3. Save and reboot.
4. You should now be able to log in with root and empty password while booted in stock firmware.
While on Openwrt, subsequent upgrades can be made by sysupgrade, or via Luci. UART should not be necessary unless you want to revert to stock firmeware.
Signed-off-by: Qing W <ses1er@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19754
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
`loglevel=8` causes the kernel to output all logs, including debug logs, at boot time
It is enabled by default on the upstream eval board because it is aimed at developer debugging.
Most devices reference the eval board directly without modification, and the debug log should be hidden at release
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19714
Signed-off-by: Robert Marko <robimarko@gmail.com>
CreatLentem CLT-R30B1 is a wireless WiFi 6 router.
This device uses the CLT-R30B1_0824_V1.1 board
shared by EDUP RT2980, Dragonglass DXG21,
and other diamond-shaped 5-antenna routers.
Specification
-------------
- SoC : MediaTek MT7981B dual-core ARM Cortex-A53 1.3 GHz
- RAM : DDR3 256 MiB
- Flash : SPI-NAND 128 MiB (ESMT F50L1G41LB)
- WLAN : MediaTek MT7976CN dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MU-MIMO (2x 5 dBi antennas)
- 5 GHz : a/n/ac/ax, MU-MIMO (3x 5 dBi antennas)
- Ethernet :
- LAN x3 : 10/100/1000 Mbps (MediaTek MT7531AE)
- WAN x1 : 10/100/1000 Mbps (MT7981 internal PHY)
- UART : through-hole on PCB
- assignment : (RX), (TX), (GND), [3.3V]
- settings : 115200n8
- Buttons x2 : Mesh/WPS, Reset
- LEDs x2 : Status (Red, Green)
- Power : 12 VDC, 1 A, 2.1*5.5 mm
Important notes
---------------
The device is supplied in two variants.
The main difference is the size of the mtd5 (ubi)
partition in the flash layout: 64M or 112M.
112M version: Has ImmortalWrt firmware installed with LuCI WebUI.
64M version: Has stock firmware based on OpenWrt,
with the WaveLink/GL.iNet WebUI and older U-Boot
compared to the 112M version.
Flash instructions for 112M version
-----------------------------------
Follow the standard OpenWrt sysupgrade procedure without saving data.
Use the clt-r30b1-112m-squashfs-sysupgrade.bin image.
All checks should pass - don't proceed if a "not supported"
warning is issued.
Flash instructions for 64M version
----------------------------------
WebUI Method:
1. Prepare the upgrade image with clt-r30b1-squashfs-sysupgrade.bin
using the script: make_staged_upgrade_tar.sh
or use the prepared image: staged_openwrt_upgrade.bin
Downloaded from:
https://github.com/andros-ua/owrt-misc/tree/main/clt-r30b1
2. Install the prepared image using the stock WebUI update page.
3. Press and hold the reset button after reboot
to wipe the stock config and gain access.
SSH Method:
1. Connect via SSH using dg:ivanlee credentials.
2. Upload the clt-r30b1-squashfs-sysupgrade.bin image.
3. Use the command: sysupgrade -n
All checks should pass - don't proceed if a "not supported"
warning is issued.
Return to stock
---------------
Flash a backup of the ubi mtdblock (mtd5)
using the OpenWrt sysupgrade method.
Recovery
--------
Both variants:
Connect UART and use the U-Boot menu to flash the firmware image
or boot an OpenWrt initramfs image.
112M with newer U-Boot:
Power on the router while pressing the mesh button for 3 seconds.
The U-Boot Flash WebUI will be available at http://192.168.1.1
MAC Addresses:
-------------------------------------------------------
| Interface | MAC | Source |
---------------|-------------------|-------------------
| LAN | B4:4D:43:D1:xx:xx | Factory, 0x2A |
| WAN | B4:4D:43:D1:xx:xx | Factory, 0x24 |
| WLAN 2.4 GHz | B4:4D:43:D2:xx:xx | Factory, 0x4 |
| WLAN 5 GHz | B4:4D:43:D2:xx:xx | Factory, 0x4 + 1 |
-------------------------------------------------------
Signed-off-by: Andrii Kuiukoff <andros.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19534
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
- SOC: MediaTek MT7981B
- RAM: 256MB DDR3
- FLASH: 128MB SPI-NAND WinBond W25N01GVZEIG
- NETWORK: 2x1Gb Lan 1x1Gb Wan
- WIFI: MediaTek MT7981B 2x2 DBDC 802.11ax 2T2R (2.4/5)
- LEDs: 3x WAN/LAN (green) 2x STATUS (red/blue)
- USB: 1x XHCI
Installation via Webinterface
-----------------------------
1. Rename OpenWrt sysupgrade bin to wavlink_wl-wn551X3-squashfs-sysupgrade.bin
The uppercase chars 551X3 are essential and checked by web interface.
2. Logon to webinterface
3. Go to network configuration -> mode selection
4. Choose mode "LAN bridge/access point"
5. Save configuration (maybe network reconfig needed)
6. Go to system upgrade
7. Choose local upgrade and provide renamed sysupgrade file
8. Start upgrade and wait for completion
9. Logon to OpenWrt (network config is preserved during upgrade)
Boot initramfs via TFTP & console
---------------------------------
1. Connect switch to network via LAN1 or LAN2
2. Power on switch
3. Press ESC until prompt reached "MT7981>"
4. Set own IP "setenv ipaddr 192.168.x.y"
5. Set TFTP IP "setenv serverip 192.168.a.b"
6. Set memory address "setenv loadaddr 0x46000000"
7. Download image "tftpboot openwrt-mediatek-filogic-wavlink_wl-wn551x3-initramfs.itb"
8. Boot image "bootm"
Notes
-----
- The red/blue LEDs give a background illumination to the top of the
case. The red LED is totally disabled to avoid noisy blinking.
- Aside from the design and the different LED colors & placements
the hardware and partitioning matches the WAVLINK WL-WN586X3 Rev B.
Therefor a common DTSI was prepared.
MAC Addresses (same as stock)
-----------------------------
LAN : 80:3F:5D:xx:xx:B1 (hw, 0x44e(text))
WAN : 80:3F:5D:xx:xx:B2 (hw, 0x460(text))
2.4GHz: 80:3F:5D:xx:xx:B1 (Factory, 0x4 (hex))
5GHz : driver auto generated
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19515
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
OpenFi 6C is a portable Wi-Fi 6 travel router based on MediaTek MT7981B+MT7976CN.
Two slightly different versions have been sold. The V1 board has a green color and lacks the modem LED. The V2 board is black and has a LED for the modem. The firmware should work on both of them.
Specifications:
- SoC: MediaTek MT7981B (Filogic 820) 1.3GHz dual-core ARM Cortex-A53
- RAM: 1GB DDR4
- Flash: 256MB SPI NAND
- Wireless: 2.4GHz/5GHz 802.11ax
- Ethernet: 1x 10/100/1000M LAN
- USB: 1x USB 3.0 Type-A port
- Expansion: M.2 slot for 5G modem
- Cooling: PWM-controlled fan
- Buttons: Reset, Mode switch
- LEDs: System, Ethernet, 5G WiFi, Modem status
**Installation via U-Boot web page**
1. Set static IP 192.168.21.2/255.255.255.0 on your computer.
2. Connect to the Ethernet port and hold the reset button while booting the device. Wait for 6-8 seconds, and release the reset button.
3. Open U-boot web page on your browser at http://192.168.21.1
4. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
5. Wait for automatic reboot.
**Installation via sysupgrade**
Flash the sysupgrade file via LuCI upgrade page without saving the settings.
Signed-off-by: Jiasheng Zhu <newbanyaya@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19512
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adds the capability to flash the factory image using the OEM recovery
software, ipTIME Firmware Wizard(11ac).
Installation
------------
1. Download the OEM recovery software from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router(keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router(LAN port) to the PC
6. Run the OEM recovery software and follow the instructions
7. Select the *squashfs-factory.bin file during the router recovery process
8. Wait for the router to boot from *squashfs-factory.bin
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19497
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This file should be generated automatically at runtime by the kernel
build system.
Link: https://github.com/openwrt/openwrt/pull/19473
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3GHz
- RAM : DDR3 256Mbytes, ESMT M15T2G16128A
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976CN dual-band Wi-Fi 6
- 2.4GHz : b/g/n/ax, MU-MIMO
- 5GHz : a/n/ac/ax, MU-MIMO
- Ethernet : MediaTek MT7531AE
- LAN : 10/100/1000 Mbps x4
- WAN : 10/100/1000 Mbps x1
- UART : 1x4 pin header on PCB
- [J6] TX, RX, GND, 3.3V (115200, 8N1)
- Buttons : WPS, Reset
- LEDs : 1x CPU (Amber)
1x Wi-Fi 5GHz (Amber)
1x Wi-Fi 2.4GHz (Amber)
1x WAN activity (Amber)
4x LAN activity (Amber)
- Power : 12VDC, 1A (Center positive polarity)
MAC address
-----------
+-----------+-------------------+-----------------------+
| Interface | MAC | Algorithm |
+-----------+-------------------+-----------------------+
| WLAN 2.4G | B0:38:6C:48:xx:xx | label |
| WLAN 5G | B2:38:6C:48:xx:xx | label with LA Bit Set |
| WAN | B0:38:6C:48:xx:xx | label + 1 |
| LAN | B0:38:6C:48:xx:xx | label + 3 |
+-----------+-------------------+-----------------------+
The WLAN 2.4G MAC was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router(keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router(LAN port) to the PC
6. Replace a file in the OEM recovery software with the file from step 2
7. Run the OEM recovery software and follow the instructions
8. Wait for the router to boot from *squashfs-factory.bin
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19368
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit increases the SPI bus frequency from 20 to 52 MHz. Reduces boot
time by 2s. Below is a performance comparison.
Before:
root@OpenWrt:~# dd if=/dev/mtd5 of=/dev/null bs=10M count=1 status=progress
10485760 bytes (10 MB, 10 MiB) copied, 2 s, 5.8 MB/
After:
root@OpenWrt:~# dd if=/dev/mtd5 of=/dev/null bs=10M count=1 status=progress
10485760 bytes (10 MB, 10 MiB) copied, 1 s, 9.7 MB/s
Taken from PR #18752 as each device should be tested individually, so I have
created a separate PR for this.
Signed-off-by: Sky Huang <SkyLake.Huang@mediatek.com>
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19439
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With the switch to Linux 6.12 this driver was enabled by accident.
However, it doesn't support any of the router SoCs but is meant to be
used only by the smartphone, tablet and chromebook SoCs.
Disable the driver again to silence a kernel error logline during boot.
Fixes: 0a0f5f94ec ("mediatek: mt7623: update config-6.12")
Fixes: 029b7ed9c4 ("mediatek: mt7622: update config-6.12")
Reported-by: https://aparcar.org/openwrt-tests/119/
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
These u-boot images are no longer automatically copied to the
bindir since commit:
ed50004319 ("uboot-mediatek: add support for Linksys E8450")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Add an OpenWrt-based U-Boot build for this device, allowing for more
flexibility and customization.
Expected behaviour
------------------
When plugging the device, keeping the reset button pressed will enter
TFTP recovery mode: the board will send requests for the initramfs file
(openwrt-mediatek-filogic-glinet_gl-mt2500-initramfs-kernel.bin) from
IP 192.168.1.1 to 192.168.1.10 TFTP server.
The bootloader will populate the environment with the unit serial number
as reported by the "sn" value in eMMC, the "sn_bak" value, the country
code and ddns. WAN and LAN MAC addresses are reported in the environment
as well.
Limitations
-----------
No web interface is available, and only the LAN port can be used for
system recovery.
Notes
-----
This port has been tested with the Maxlinear version only, and with a
board that does not exhibit eMMC communication problems. Even though eMMC
frequency has been lowered, some testing is probably needed and always
very welcome.
A -factory image has been introduced, and is only needed when using the
"Load Firmware via TFTP then write to eMMC." boot menu function.
The device has not been converted to use uImage.FIT including the rootfs
to keep compatibility with stock bootloader and firmware.
Installation
------------
From a Linux root shell:
0. Transfer the needed files to the board, placing them in /tmp.
1. Make sure your U-Boot environment is erased: all of my units came with
unpopulated environment, but I am not sure this is always the case.
Issue the command
cat /dev/zero >/dev/mmcblk0p2
(you will get a "no space left" error, which is reasonable and expected).
2. Unlock the eMMC boot area where BL2 is located:
echo 0 >/sys/block/mmcblk0boot0/force_ro
3. Write the new BL2 code:
cat openwrt-mediatek-filogic-glinet_gl-mt2500-emmc-preloader.bin >/dev/mmcblk0boot0
4. Write new BL31+U-Boot image:
cat openwrt-mediatek-filogic-glinet_gl-mt2500-emmc-bl31-uboot.fip >/dev/mmcblk0p4
5. Reboot.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
The device is equipped with a GPS module, reporting data via /dev/ttyS1.
A TF card reader is also present. Only one of those components can be
used at once, since they share some PINs.
This commit adds two devicetree overlays to allow for the user to select
the desired configuration. Another overlay configuration to allow booting
from SD card is provided.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Add WED related nodes to the device tree of the MT7988 SoC family.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Currently, if OEM recovery flashes OpenWrt to second ubi1,
OpenWrt cannot boot. With this commit, recovery image is built
with initramfs kernel, so that it can boot from either ubi or ubi1.
This adds an extra step to OpenWrt installation from OEM:
user needs to sysupgrade from initramfs to full system.
Signed-off-by: Mateusz Krzak <kszaquitto+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18878
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
8mA driving will cause overshoot issue on SPI NAND. Change it to 4mA.
- Reference:
003744197a
On Linux mainline (mt7986.dtsi), spi's source clock is: clocks = <&topckgen CLK_TOP_MPLL_D2>, which is
208MHz. Usable clock division will be:
- 208/4=52MHz
- 208/6~=35MHz
- 208/8=26MHz
and so on
If we specify 50MHz for spi-max-frequency, it will actually run under about 35MHz. Most SPI NAND & NOR
flashes are capable of running with more than 52MHz, include Micorn MT29F4G01ABAFDWB on ZyXEL EX5601.
[Ref: #18752] To reach highest performance on mt7986, use spi-max-frequency = <520000000>. Basically,
this setting should work on all mt7986 PCBs since most mt7986 boards follow reference design. However,
other boards needs further test to guarantee stability.
Signed-off-by: Sky Huang <SkyLake.Huang@mediatek.com>
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/18813
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move the following kernel symbol configs to generic:
COMPRESSED_INSTALL and IMX_SCMI related configs
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/19380
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since not every device sets an ubifs partition name as the same as their
parent mtd partition, this change allows mount_ubi_part to usable in
other devices
Signed-off-by: Yonghyu Ban <yhban@silicon.moe>
Link: https://github.com/openwrt/openwrt/pull/19203
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
**Huasifei WH3000 Pro**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC. MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ with 5G modems module and PWM Fan.
**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8GB
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: power/reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1
**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.
**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.
**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-pro-squashfs-sysupgrade.bin
```
**Factory MAC**
You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4`
```
dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C
```
Cherry-picked from 949d0bd77a
Fixed `green` to `blue` LED in dts, added `SUPPORTED_DEVICES += huasifei,fudy-pro` - to make sysupgrade compatible with factory QWRT/Lede fork firmware.
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19315
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Force update_cache_variantsvariants to use reset for Foresee NAND with bad blocks.
Tested on Xiaomi AX3000T + F35SQA001G with bad blocks and without bad blocks
Signed-off-by: Dim Fish <dimfish@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17963
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Move changes to mt7988a.dtsi from patch adding the support for the
MT7988A Reference Board to a dedicated patch to ease maintainance.
Fixes: f9206d1111 ("kernel/mediatek: 6.12: replace downstream files by patches")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Restore the conversion to an all-UBI NAND layout and use of fitblk on
SPI-NAND connected via the mt65xx SPI controller.
Apply the same also for SPI-NAND connected via the SNFI controller, and
use fitblk also for boot from SPI-NOR, eMMC and SD.
Fixes: f9206d1111 ("kernel/mediatek: 6.12: replace downstream files by patches")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The MediaTek MT7988A RFB currently hangs on boot as CCI fails to probe.
This is due to the wrong SoC compatible string "mediatek,mt7988" instead of
"mediatek,mt7988a". Fix that.
Fixes: f9206d1111 ("kernel/mediatek: 6.12: replace downstream files by patches")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix the status indicator light of the LAN port.
Signed-off-by: jinkela air <air_jinkela@163.com>
Link: https://github.com/openwrt/openwrt/pull/19135
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
