The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport upstream patch to add support for the ESMT F50L1G41LC flash
chip. It is used in multiple Cudy products manufactured starting
November 2025.
Link: https://github.com/openwrt/openwrt/pull/20962
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
IPQ5018 based boards come in multiple wireless architectures.
The SOC itself provides 2.4G wifi while 5G wifi is added by either an
IPQ5018-specific QCN6122 (2x2) solution or by the more generally
available PCIe-based QCN9074 (4x4) wifi chip.
On IPQ5018/QCN6122-based boards, both QCN6122 and IPQ5018 wifi is
initialized by IPQ5018 firmware which comes in different versions:
- IPQ5018: firmware files to initialize WCSS and the internal wifi chip
- IPQ5018/QCN6122: above + additional firmware segments to initialize
the QCN6122 chip incl. (de-)assertion of resets and clocks enablement
OpenWrt currently packages the combined IPQ5018/QCN6122 firmware for
both architectures. As such, let's switch to using IPQ5018-only firmware
for boards not packed with QCN6122 chip(s) and keep using the shared
firmware for devices that do have QCN6122(s) chips.
This helps us move to using upstreamed IPQ5018 firmware while using the
legacy repo for IPQ5018/QCN6122 firmware and rule out any initialization
conflicts/issues caused by loading QCN6122 on IPQ5018-only boards.
While at it, default to the secure WCSS remoteproc driver sent upstream
for review, move QCN6122 wifi nodes to a separate dtsi, override the Q6
node to load the multi-PD-based architecture remoteproc driver for
needed only by IPQ5018/QCN6122 designs, reference said dtsi in
boards packed with QCN6122 wifi chip(s), and add provision for migrating
the radio path as the wifi nodes now adhere to linux device tree naming
conventions.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20928
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for qcom remoteproc WCSS secure PIL driver.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20928
Signed-off-by: Robert Marko <robimarko@gmail.com>
`i2c1` node was missing `resets`, so even when enabled, the driver would
not recognize it:
```
i2c_designware c101000.i2c: Unknown Synopsys component type: 0x00000000
```
With this fix, I2C pins on BPi-RV2 26-pin GPIO header are usable.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20969
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Now that NVMEM in UBI is supported, more handling can be moved.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16376
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All users of regular CONFIG_NVMEM_U_BOOOT_ENV have been converted to use
layouts.
CONFIG_NVMEM_U_BOOT_ENV selects the layout variant anyway so this is
safe to do.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16376
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Define MSM466 as alternative name, to explicitly show the device is
supported using existing image (MSM460). The only difference between
the MSM460 and MSM466 is that the MSM466 has external antenna.
Signed-off-by: Raylynn Knight <rayknight@me.com>
Link: https://github.com/openwrt/openwrt/pull/20937
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the missing symbol to fix build halt on aarch64 targets:
```
Contiguous PTE mappings for user memory (ARM64_CONTPTE) [Y/n/?] (NEW) make[7]: *** [scripts/kconfig/Makefile:85: syncconfig] Error 1
make[6]: *** [Makefile:686: syncconfig] Error 2
```
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20954
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The child node "partitions" doesn't have "reg" property. Hence, we
don't need to use "#address-cells" and "#size-cells" to describe the
reg property information.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20942
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The child node "partitions" doesn't have "reg" property. Hence, we
don't need to use "#address-cells" and "#size-cells" to describe the
reg property information.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20942
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patchset silences some noisy dts false warnings:
[ 0.616266] OF: Bad cell count for /spi@1100d000/flash@0/partitions
[ 0.622551] OF: Bad cell count for /spi@1100d000/flash@0/partitions
Closes: https://github.com/openwrt/openwrt/issues/14701
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20942
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop all kernel 6.6 patches, hacks, backports and configuration support,
and remove the CONFIG_LINUX_6_6 guarded conditional in filogic.mk.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/20943
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
node name matches various comments about the pci path.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20522
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kernel update commit also changed the name of the dtsi node. Adapt
the other dts files.
Fixes: 738876e76b ("kernel: bump 6.12 to 6.12.58")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Drop support for kernel 6.6 as now kernel 6.12 is set as default kernel
version.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20889
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Fortinet FortiWiFi 30E (FWF-30E) is a UTM, based on Armada 385 (88F6820).
Specification:
- SoC : Marvell Armada 385 88F6820
- RAM : DDR3 1 GiB (4x Nanya NT5CC256M8IN-D1)
- Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- Ethernet : 5x 10/100/1000 Mbps
- Switch : Marvell 88E6176
- Wireless : Atheros AR9382 2x2 802.11abgn (mini-PCIe)
- LEDs/Keys : 16x/1x
- UART : "CONSOLE" port (RJ-45, RS-232C level)
- port : ttyS0
- settings : 9600bps 8n1
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- note : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- USB : 1x USB 3.0
- Power : 12 VDC, 2 A
- plug : Molex 5557-02R
Flash instruction using initramfs image:
1. Power on FWF-30E and interrupt to show bootmenu
2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
and set baudrate to 9600 bps
3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
connect computer to "Image download port" in the parameters
4. Prepare TFTP server with the parameters obtained above
5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
directory
6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
image from TFTP server
7. Type "r" key when the following message is showed, to boot initramfs
image without flashing to spi-nor flash
"Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"
8. On initramfs image, backup mtd if needed
minimum:
- "firmware-info"
- "kernel"
- "rootfs"
9. On initramfs image, upload sysupgrade image to the device and perform
sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
If the device is booted with stock firmware, login to bootmenu and
call "[B]: Boot with backup firmware and set as default." to set the
first OS image as default and boot it.
Notes:
- Both colors of Bi-color LEDs on the front panel cannot be turned on at
the same time.
- "PWR" and "Logo" LEDs are connected to power source directly.
- The following partitions are added for OpenWrt.
These partitions are contained in "uboot" partition (0x0-0x1fffff) on
stock firmware.
- "firmware-info"
- "dtb"
- "u-boot-env"
- "board-info"
Image header for bootmenu tftp:
0x0 - 0xf : ?
0x10 - 0x2f : Image Name
0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?
*: required for initramfs image
MAC addresses:
(eth0): 70:4C:A5:xx:xx:42 (board-info, 0xd880 (hex))
WAN : 70:4C:A5:xx:xx:43
LAN 1 : 70:4C:A5:xx:xx:44
LAN 2 : 70:4C:A5:xx:xx:45
LAN 3 : 70:4C:A5:xx:xx:46
LAN 4 : 70:4C:A5:xx:xx:47
Signed-off-by: Jimmy Cavanaugh <jamie@cavanaugh.co.nz>
Link: https://github.com/openwrt/openwrt/pull/20787
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
As per schematics, GPIO 30 is incorrect to use as the reset pin for the
QSGMII PHY SF23P1240; the correct one is GPIO 22.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20925
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
refreshed with make kernel_oldconfig CONFIG_TARGET=subtarget
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20893
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
adding the kmod-i2c-designware-platform by user suggestion
Co-authored-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20893
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop support for kernel 6.6 as now kernel 6.12 is set as default kernel
version.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20893
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
switch the kernel to 6.12 by default
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20893
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Devices package:
Add missing USB3 driver
Device tree:
Fix model name and pwm usage
Add missing supply for I2C and USB
Update network port names based on the shell image [1]
[1] https://docs.banana-pi.org/bpi-r4_lite/banana_pi_bpi-r4_lite_case_1.png
Fixes: 8b6c6978 ("mediatek: add support for BananaPi BPi-R4 Lite")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
There is no reason to limit USB to 2.0 mode by default. This
limitation should be done when both gmac2 and USB are enabled.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Remove I2C, PCIe, PWM, UART and USB from the MT7987A SoC dtsi.
These should not be enabled by default, but rather enabled based
on the device.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Drop support for kernel 6.6 as now kernel 6.12 is set as default kernel
version.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20892
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
switch the kernel to 6.12 by default
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20892
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop support for kernel 6.6 as now kernel 6.12 is set as default kernel
version.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20871
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
switch the kernel to 6.12 by default
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20871
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop support for kernel 6.6 as now kernel 6.12 is set as default kernel
version.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20874
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
switch the kernel to 6.12 by default
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20874
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop support for kernel 6.6 as now kernel 6.12 is set as default kernel
version.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20887
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
switch the kernel to 6.12 by default
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20887
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop support for kernel 6.6 as now kernel 6.12 is set as default kernel
version.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20888
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
switch the kernel to 6.12 by default
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20888
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
- Added fan0 alias
- Implemented LED aliases and thermal zones
- Restructured partitions: u-boot, u-boot-env, ubi
Signed-off-by: Konstantin Meshkov <skyline@mail.ru>
[ improve commit title ]
Link: https://github.com/openwrt/openwrt/pull/17924
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The D-Link DNS-325 A1 is NAS with 2x HDD (3.5 inch) bays, 1x 10/100/1000Base-T port and 1x USB 2.0 port
Device specification:
SoC: Marvell 88F6281-A1 1.2 GHz
RAM: 256 MB (2xSEC K4T1G084QF-HCF7:128Mx8 @400 CL6)
Flash: 128 MB (SAMSUNG 946 K9F1G08U0B PCB0)
SATA: 2x internal SATA II drives
Ethernet: 1x Gigabit (Marvell 88E1116R-NNC1)
LED: 7x (white: Power, white/red: Right SATA Activity, USB Activity, Left SATA Activity)
Key: 3x (Power, Reset, USB Copy/Unmount)
Serial: 5 pin header (RXD,GAP,3.3V,GND,TXD), (115200,8,N,1), 3.3V TTL
USB ports: 1x USB 2.0
Flash instruction:
NOTE: this process uses a serial connection. It will upgrade the bootloader and reset the bootloader environment variables
USB flash stick setup
Format to FAT32 without mbr
Copy these files to USB flash stick: dlink_dns-325-a1-initramfs-uImage dlink_dns-325-a1-squashfs-factory.bin dlink_dns-325-a1-squashfs-sysupgrade.bin u-boot.kwb (from u-boot-dns325 directory)
NAS setup
Connect LAN cable between router and NAS device
Connetc USB flash stick to NAS device
Connect serial to NAS device
Boot from new u-boot and install it
$ kwboot -p -b u-boot.kwb -B115200 -t /dev/ttyUSB0
Power on NAS
After download copleted and booted NAS device with new u-boot stop in bootloader by pressing any key
=> usb start
=> fatload usb 0 0x1000000 /u-boot.kwb
=> nand erase.part u-boot
=> nand write 0x1000000 u-boot ${filesize}
=> reset
Update MAC address in u-boot env
Stop in bootloader by pressing any key
Get your MAC address from label on chassis
=> setenv ethaddr XX:XX:XX:XX:XX:XX
=> saveenv
Install OpenWrt by flashing factory image from u-boot
=> usb start
=> fatload usb 0 0x1000000 /dlink_dns-325-a1-squashfs-factory.bin
=> nand erase.part ubi
=> nand write 0x1000000 ubi ${filesize}
=> reset
Based-on: #9296
Signed-off-by: Konstantin Meshkov <skyline@mail.ru>
[ refresh uboot patches ]
Link: https://github.com/openwrt/openwrt/pull/17924
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
These patches fix the remaining issues with BCM5325 switches and allow
dropping the default VLAN on Huawei HG556a.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This device has one USB2.0 port, plus ethernet, 2x wifi, ethernet, xPON
and VoIP.
Installation instructions: (Assuming root shell via SSH or serial)
1. Place OpenWrt TRX file on a USB stick formatted VFAT
2. Plug in the stick to the modem
3. Type: mtd write -f -e tclinux /mnt/usb2_sda1/<name of file>.trx tclinux
At this point, both OpenWrt and the vendor OS will be installed
because the device has space for two operating systems. Switch the OS
to boot to OpenWrt:
1. mtd readflash tmpdata 999999999 0 reservearea
2. echo -n '0' | dd of=./tmpdata bs=1 count=1 seek=397311 conv=notrunc
3. mtd write -f -e reservearea ./tmpdata reservearea
4. reboot
WARNING: While you can install with SSH alone, you need serial to use
OpenWrt on EcoNet devices because the Ethernet driver has not yet been
developed.
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://github.com/openwrt/openwrt/pull/20580
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The parameters must be aligned based on the last opened parenthesis
(+1). If this not a multiple of the tab size (8) then the rest
alignment must be done using spaces.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://github.com/openwrt/openwrt/pull/20906
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is written "multi" and not "mutli"
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://github.com/openwrt/openwrt/pull/20906
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is written "initialization" and not "intialization"
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://github.com/openwrt/openwrt/pull/20906
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
