Refresh patch which was accidentally without non-confrming style and
not matching line numbers.
Also add patch description by copying the description of the commit
in OpenWrt, so the patch can be applied using `git am` and is ready
for upstream submission.
Fixes: afcec128c5 ("mediatek: add support for trng on mt7988a")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Converts the KS8995 "phy" driver to a proper DSA switch.
Currently the upstream only supports the "none" tag
but this is a good improvement already.
Make the old module depend on kernel 6.6 and the new
one depend on !6.6.
The Realtek RTL8261n patch needs to be refreshed
because of textual dependencies.
Realtek RTL838x DSA and phy patches also have textual
dependencies and need to be refreshed.
The Mediatek in-flight DSA patch and related patches
also need to be rebased and refreshed.
Link: https://github.com/openwrt/openwrt/pull/19970
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change fixes the eeprom load failure while on boot
Signed-off-by: Rhnn Hur <hurrhnn@icmp.kr>
Link: https://github.com/openwrt/openwrt/pull/20044
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification
-------------
- SoC : MediaTek MT7986AV quad-core ARM Cortex-A53 2GHz
- RAM : DDR4 512Mbytes, Nanya Technology NT5AD256M16E4
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976DAN, MediaTek MT7916AN, MediaTek MT7976AN
- 2.4GHz : b/g/n/ax, Multi User MIMO
- 5GHz : a/n/ac/ax, Multi User MIMO
- 6GHz : ax, Multi User MIMO
- Ethernet : 10/100/1000 Mbps x4, LAN (MediaTek MT7531AE)
10/100/1000/2500 Mbps x1, WAN (MaxLinear GPY211C0VC)
- UART : 1x4 pin header on PCB
- [J1] 3.3V, TX, RX, GND (115200, 8N1)
- Buttons : WPS, Reset
- Switches : Rfkill Slide Switch
- USB : 1x USB 3.0 (MediaTek MT7986AV peripheral)
- FAN : 1x Fan (off - slow - fast)
- LEDs : 1x Power (Blue)
1x CPU (Blue)
1x Wi-Fi 6GHz (Blue)
1x Wi-Fi 5GHz (Blue)
1x Wi-Fi 2.4GHz (Blue)
4x LAN activity (Blue)
1x WAN activity (Blue)
1x USB 3.0 (Blue)
- Power : 12VDC, 3.5A (Center positive polarity)
MAC address
-----------
+-----------+-------------------+------------------------+
| Interface | MAC | Algorithm |
+-----------+-------------------+------------------------+
| WLAN 2.4G | 58:86:94:xx:xx:xx | label1 |
| WLAN 5G | 5A:86:94:xx:xx:xx | label2 with LA Bit set |
| WLAN 6G | 5A:86:94:xx:xx:xx | label1 with LA Bit set |
| WAN | 58:86:94:xx:xx:xx | label1 + 1 |
| LAN | 58:86:94:xx:xx:xx | label1 + 3 |
+-----------+-------------------+------------------------+
The WLAN 2.4G MAC address (label1) was found in 'Factory' partition, 0xA0004
The WLAN 5G MAC address (label2) was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software (ipTIME Firmware Wizard (11ac))
from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router (keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router (LAN port) to the PC
6. Run the OEM recovery software and follow the instructions
7. Select the *squashfs-factory.bin file during the router recovery process
8. Wait for the router to boot from *squashfs-factory.bin
Note: The router will automatically reboot if no file is uploaded within
55 seconds.
Fan Control
------------
The fan speed is controlled by writing a value from 0 to 2 to the
`fan1_target` file.
```
cd /sys/devices/platform/gpio-fan/hwmon/hwmon2
echo '0' > fan1_target // off
echo '1' > fan1_target // slow
echo '2' > fan1_target // fast
```
Limitation: Enabling Wi-Fi 6E
----------
Wi-Fi 6E (6GHz) does not work out of the box on LuCI.
After installation, you need to configure a few settings in the `radio1`
and `default_radio1` sections of the `/etc/config/wireless`.
Once you have made these changes, you can enable and use Wi-Fi 6E.
In the `radio1` section, you need to add three common options:
- band: must be set to `6g`
- country: a valid country code for the 6GHz band
- channel: a preferrend scanning channel (PSC) for 6GHz
In the `default_radio1` section, you need to add the SSID and key:
- ssid: The public name of your Wi-Fi network
- key: The Wi-Fi password
- encryption: must be set to either `sae` for WPA3 or `owe` for OWE
(open network)
Example:
```
config wifi-device 'radio1'
...
option band '6g'
option country 'KR'
option channel '37'
...
config wifi-iface 'default_radio1'
...
option ssid 'my_wifi_6e_name'
option key 'my_strong_password1234'
option encryption 'sae'
...
```
Note: A list of all the 6GHz PSC channels:
```
5, 21, 37, 53, 69, 85, 101, 117, 133, 149, 165, 181, 197, 213, and 229
```
Limitation: Maximum Transmit Power
----------
The maximum transmit power is currently broken. In the drop-down menu,
you can only choose between "driver default" and "255 dBm (2147493647
mW)". There is currently no workaround for the issue. Please leave the
maximum transmit power set to "driver default".
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19763
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add driver for hardware random number generator found in MT7981, MT7988
and MT7987. This gives us a fast source of high-quality random numbers
on those platforms.
root@OpenWrt:~# cat /dev/hwrng | rngtest -c 10000
rngtest 6.17
Copyright (c) 2004 by Henrique de Moraes Holschuh
This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
rngtest: starting FIPS tests...
rngtest: bits received from input: 200000032
rngtest: FIPS 140-2 successes: 9988
rngtest: FIPS 140-2 failures: 12
rngtest: FIPS 140-2(2001-10-10) Monobit: 2
rngtest: FIPS 140-2(2001-10-10) Poker: 0
rngtest: FIPS 140-2(2001-10-10) Runs: 4
rngtest: FIPS 140-2(2001-10-10) Long run: 6
rngtest: FIPS 140-2(2001-10-10) Continuous run: 0
rngtest: input channel speed: (min=616.108; avg=11979.007; max=19531250.000)Kibits/s
rngtest: FIPS tests speed: (min=1.859; avg=82.116; max=83.656)Mibits/s
rngtest: Program run time: 18629928 microseconds
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add labels wan and cpu for ethernet ports.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19968
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently 5G wireless interface MAC address is incorrect.
Fix by setting MAC address using Factory data.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19968
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Convert NWA50AX Pro to use NVMEM framework for wifi macaddr.
Also remove the unused macaddr@a.
Signed-off-by: Zhi-Jun You <hujy652@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/19982
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Convert NWA50AX Pro to use NVMEM framework for EEPROM/precal.
Signed-off-by: Zhi-Jun You <hujy652@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/19982
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The devices are basically identical. The RAX3000Me can be with
ddr3 RAM.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19760
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds ddr3 build for the ddr3 variant of the CMCC RAX3000Me
router.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19760
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
MediaTek MT7981 WiSoC
512MB DDR4 RAM
128MB SPI-NAND
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
4 LAN MediaTek MT7531 PHY
1 WAN RTL8221B-VB-CG 2.5Gbps PHY
UART: 115200 8N1 3.3V
USB2 Port
PoE on WAN Port
MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set
Gotchas:
WAN LED does not light up (might require further DTS tweaks)
PoE on WAN port was not tested
This commit is heavily based on WR3000H one, I've just ported DTS differences
from the official image to get USB support and proper LED mapping.
Installation
------------
[Untested as I've received and used a transitional image from Cudy]
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device + press reset pin. Keep pressing reset pin to enter the U-Boot shell.
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.88. Rename the image to "cudy3000p.bin"
4. Download and boot the OpenWrt initramfs image.
$ tftpboot 0x46000000 cudy3000s.bin; bootm 0x46000000
5. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Signed-off-by: Michal Halva <hedik01@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19636
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport support for Aeonsemi AS121xxx PHY. The PHY require dedicated
firmware to be loaded to correctly work and support a big family of
Aeonsemi PHY that provide from 1G to 10G speed.
Automatically refresh all affected patch and file (rtl PHY).
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Import upstream patches fixing issues with unreliable temperature
reading on some batches of the MediaTek MT7988 SoCs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use macro defined bias types instead of some magic numbers. This can
help reviewers better understand bias types.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19855
Signed-off-by: Robert Marko <robimarko@gmail.com>
The kmod is installed on all filogic mediatek images, even for devices
that do not have any aquantia hardware. Remove it.
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19488
[Do not explicitly remove kmod-phy-aquantia from gatonetworks_gdsp]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for the WAVLINK WL-WN586X3 Rev B, which swaps
the 16MB NOR flash for an 128MB NAND flash chip, and uses UBI for
data partition. This commit utilizes the previous submitted dtsi that
includes common hardware for a few Wavlink routers.
Hardware
--------
- SOC: MediaTek MT7981B
- RAM: 256MB DDR3
- Flash: 128MB SPI-NAND (ESMT F50L1G41LB)
- Ethernet: 2x1Gb Lan 1x1Gb Wan
- WiFi: MediaTek MT7981B 2x2 DBDC 802.11ax 2T2R (2.4/5) with 4 external and 1 internal antennae
- LEDs: 2xLan 1x Wan 1x WIFI 1xSTATUS
Installation
------------
Flashing over the vendor WebUI has been tested and unsuccessful (YMMV).
The image need to be flashed via TFTP which can be activated over the onboard UART serial console:
1. Connect UART: TX->board RX, RX->board TX, GND->board GND.
2. Connect PC to router lan port.
3. Setup the tftp server on PC, set IP to 192.168.10.100.
4. Power on the device. Interrupt boot countdown at uboot boot menu and select 2. Upgrade firmware option.
5. Input the image name and start flashing.
Sample uboot menu:
```
*** U-Boot Boot Menu ***
1. Startup system (Default)
2. Upgrade firmware
3. Upgrade ATF BL2
4. Upgrade ATF FIP
5. Upgrade single image
6. Load image
0. U-Boot console
```
NOTE: Do not use the intermediate image here which is for Rev A only:
https://github.com/themaverickdm/firmware-misc/tree/main/wavlink/wl-wn586x3
MAC Addresses
-------------
LAN: 80:3F:5D:xx:xx:x1 (hw, 0x44e, ASCII encoded)
WAN: 80:3F:5D:xx:xx:x2 (hw, 0x460, ASCII encoded)
2G: 80:3F:5D:xx:xx:x3 (factory, 0x4, raw binary, also on label)
5G: 80:3F:5D:xx:xx:x3 (Same as 2G)
Signed-off-by: Zhenfu Shi <i0ntempest@i0ntempest.com>
Link: https://github.com/openwrt/openwrt/pull/19785
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
mt7531 switch reset delay time is hard coded in the driver. The
"reset-assert-us" and "reset-deassert-us" won't take effect.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19741
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use tabs to align and remove some unnecessary spaces.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19741
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
They were lost when ported to the 6.12 kernel.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19741
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Mediatek pinctrl driver can only accepts drive-strength values
enumerated in "dt-bindings/pinctrl/mt65xx.h".
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19741
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the missing "device_type" property to fix the memory node. The
Linux kernel can not get the memory size without it. Though u-boot
can automatically fixup the memory node by adding the "device_type"
and "reg" properties if the CONFIG_ARCH_FIXUP_FDT_MEMORY symbol is
enabled, it's better not to rely on this optional feature. This
patch also adds the reg address for the memory node name to follow
the naming rules.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19741
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Product name: Acer Predator Connect W6x
Product link: https://www.acer.com/us-en/predator/networking/wi-fi/predator-connect-w6x/pdp/FF.G2TTA.001
* Specifications:
SOC: MT7986AV
RAM: 1024MB
Flash: 256 MB SPI NAND
Ports: 4 LAN (1G) & 1 WAN (2.5G)
WIFI: MT7976GN + MT7976AN
LED: 1, ws2812b controller
* Installation via UART:
1. Configure TFTP server with IP 192.168.1.66. Copy `openwrt-mediatek-filogic-acer_predator-w6x-initramfs-kernel.bin` to TFTP root and rename to `predator.bin`
2. Interrupt boot by pressing 0 on startup or select `U-Boot Console` in U-Boot Boot Menu.
3. Run setenv `serverip 192.168.1.66; setenv ipaddr 192.168.1.1; tftpboot 0x46000000 predator.bin; fdt addr $(fdtcontroladdr); fdt rm /signature; bootm` in uboot console.
4. Wait for boot complete on Openwrt initramfs env.
** You can back up the MTD partitions at this point. Refer to Backup Instructions section.
5. On client PC, transfer `openwrt-mediatek-filogic-acer_predator-w6x-squashfs-sysupgrade.bin` to /tmp/ - `scp -O openwrt-mediatek-filogic-acer_predator-w6x-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/sysupgrade.bin`
6. On router, run sysupgrade - `sysupgrade -n /tmp/sysupgrade.bin`
Should now boot to Openwrt. Ensure it boots automatically to Openwrt by replugging the power.
* Backup Instructions:
Layout from stock firmware:
```
[ 0.968731] Creating 10 MTD partitions on "nmbm_spim_nand":
[ 0.974297] 0x000000000000-0x000000100000 : "BL2"
[ 0.979424] 0x000000100000-0x000000180000 : "u-boot-env"
[ 0.985032] 0x000000180000-0x000000380000 : "Factory"
[ 0.990379] 0x000000380000-0x000000580000 : "FIP"
[ 0.995378] 0x000000580000-0x000000600000 : "prod"
[ 1.000461] 0x000000600000-0x000000700000 : "dual"
[ 1.005527] 0x000000700000-0x000000800000 : "pot"
[ 1.010516] 0x000000800000-0x000006c00000 : "ubi"
[ 1.015626] 0x000006c00000-0x00000d000000 : "ubi1"
[ 1.020801] 0x00000d000000-0x00000d800000 : "storage"
```
Mapping in initramfs env:
```
dev: size erasesize name
mtd0: 00100000 00020000 "bl2"
mtd1: 00080000 00020000 "u-boot-env"
mtd2: 00200000 00020000 "factory"
mtd3: 00200000 00020000 "fip"
mtd4: 00020000 00020000 "prod"
mtd5: 00100000 00020000 "dual"
mtd6: 00100000 00020000 "pot"
mtd7: 06400000 00020000 "ubi"
mtd8: 06400000 00020000 "ubi1"
mtd9: 00800000 00020000 "storage"
```
1. While in openwrt initramfs environment, back up all the partitions by running the following:
```
cat /dev/mtd0 > /tmp/bl2.bin
cat /dev/mtd1 > /tmp/u-boot-env.bin
cat /dev/mtd2 > /tmp/factgory.bin
cat /dev/mtd3 > /tmp/fip.bin
cat /dev/mtd4 > /tmp/prod.bin
cat /dev/mtd5 > /tmp/dual.bin
cat /dev/mtd6 > /tmp/pot.bin
cat /dev/mtd7 > /tmp/ubi.bin
cat /dev/mtd8 > /tmp/ubi1.bin
cat /dev/mtd9 > /tmp/storage.bin
```
2. Transfer files to client PC for safekeeping. On client PC, run `scp -O root@192.168.1.1:/tmp/*.bin ./`
* Restore to Stock Firmware:
1. Boot to openwrt initramfs env.
2. Confirm layout matches as follows by running `cat /proc/mtd`. Ensure dev `mtd7` is named `ubi`:
```
dev: size erasesize name
mtd0: 00100000 00020000 "bl2"
mtd1: 00080000 00020000 "u-boot-env"
mtd2: 00200000 00020000 "factory"
mtd3: 00200000 00020000 "fip"
mtd4: 00020000 00020000 "prod"
mtd5: 00100000 00020000 "dual"
mtd6: 00100000 00020000 "pot"
mtd7: 06400000 00020000 "ubi"
mtd8: 06400000 00020000 "ubi1"
mtd9: 00800000 00020000 "storage"
```
3. Detach `ubi` partition - `ubidetach -p /dev/mtd7`
4. Transfer stock firmware's `ubi.bin` to router from client PC: `scp -O ubi.bin root@192.168.1.1/tmp/`
5. Format and replace with backup `ubiformat /dev/mtd7 -y -f /tmp/ubi.bin`
6. Reboot and you should now be back on stock firmware.
* LEDS:
LED color can be controlled by specifying values in GRB format in `/sys/class/leds/rgb:status/multi_intensity`. Default is `255 255 255` (white).
Example: `echo '75 0 130' > /sys/class/leds/rgb:status/multi_intensity`
LED brightness can be changed by specifying the value from 0-255 in /sys/class/leds/rgb:status/brightness. Default is `255` (full brightness).
Example: `echo 100 > /sys/class/leds/rgb:status/brightness`
For persistence across reboots, put the relevant command(s) in /etc/rc.local.
* Notes:
root access on stock firmware:
Before flashing openwrt, and while in openwrt initramfs env:
1. Mount /dev/ubi0_2: `mkdir /tmp/ubi0_2; mount -t ubifs /dev/ubi0_2 /tmp/ubi0_2`
2. Modify `/tmp/ubi0_2/upper/etc/passwd` and change line with `root❌0:0...` to `root::0:0...`, remove the `x`.
3. Save and reboot.
4. You should now be able to log in with root and empty password while booted in stock firmware.
While on Openwrt, subsequent upgrades can be made by sysupgrade, or via Luci. UART should not be necessary unless you want to revert to stock firmeware.
Signed-off-by: Qing W <ses1er@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19754
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
`loglevel=8` causes the kernel to output all logs, including debug logs, at boot time
It is enabled by default on the upstream eval board because it is aimed at developer debugging.
Most devices reference the eval board directly without modification, and the debug log should be hidden at release
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19714
Signed-off-by: Robert Marko <robimarko@gmail.com>
CreatLentem CLT-R30B1 is a wireless WiFi 6 router.
This device uses the CLT-R30B1_0824_V1.1 board
shared by EDUP RT2980, Dragonglass DXG21,
and other diamond-shaped 5-antenna routers.
Specification
-------------
- SoC : MediaTek MT7981B dual-core ARM Cortex-A53 1.3 GHz
- RAM : DDR3 256 MiB
- Flash : SPI-NAND 128 MiB (ESMT F50L1G41LB)
- WLAN : MediaTek MT7976CN dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MU-MIMO (2x 5 dBi antennas)
- 5 GHz : a/n/ac/ax, MU-MIMO (3x 5 dBi antennas)
- Ethernet :
- LAN x3 : 10/100/1000 Mbps (MediaTek MT7531AE)
- WAN x1 : 10/100/1000 Mbps (MT7981 internal PHY)
- UART : through-hole on PCB
- assignment : (RX), (TX), (GND), [3.3V]
- settings : 115200n8
- Buttons x2 : Mesh/WPS, Reset
- LEDs x2 : Status (Red, Green)
- Power : 12 VDC, 1 A, 2.1*5.5 mm
Important notes
---------------
The device is supplied in two variants.
The main difference is the size of the mtd5 (ubi)
partition in the flash layout: 64M or 112M.
112M version: Has ImmortalWrt firmware installed with LuCI WebUI.
64M version: Has stock firmware based on OpenWrt,
with the WaveLink/GL.iNet WebUI and older U-Boot
compared to the 112M version.
Flash instructions for 112M version
-----------------------------------
Follow the standard OpenWrt sysupgrade procedure without saving data.
Use the clt-r30b1-112m-squashfs-sysupgrade.bin image.
All checks should pass - don't proceed if a "not supported"
warning is issued.
Flash instructions for 64M version
----------------------------------
WebUI Method:
1. Prepare the upgrade image with clt-r30b1-squashfs-sysupgrade.bin
using the script: make_staged_upgrade_tar.sh
or use the prepared image: staged_openwrt_upgrade.bin
Downloaded from:
https://github.com/andros-ua/owrt-misc/tree/main/clt-r30b1
2. Install the prepared image using the stock WebUI update page.
3. Press and hold the reset button after reboot
to wipe the stock config and gain access.
SSH Method:
1. Connect via SSH using dg:ivanlee credentials.
2. Upload the clt-r30b1-squashfs-sysupgrade.bin image.
3. Use the command: sysupgrade -n
All checks should pass - don't proceed if a "not supported"
warning is issued.
Return to stock
---------------
Flash a backup of the ubi mtdblock (mtd5)
using the OpenWrt sysupgrade method.
Recovery
--------
Both variants:
Connect UART and use the U-Boot menu to flash the firmware image
or boot an OpenWrt initramfs image.
112M with newer U-Boot:
Power on the router while pressing the mesh button for 3 seconds.
The U-Boot Flash WebUI will be available at http://192.168.1.1
MAC Addresses:
-------------------------------------------------------
| Interface | MAC | Source |
---------------|-------------------|-------------------
| LAN | B4:4D:43:D1:xx:xx | Factory, 0x2A |
| WAN | B4:4D:43:D1:xx:xx | Factory, 0x24 |
| WLAN 2.4 GHz | B4:4D:43:D2:xx:xx | Factory, 0x4 |
| WLAN 5 GHz | B4:4D:43:D2:xx:xx | Factory, 0x4 + 1 |
-------------------------------------------------------
Signed-off-by: Andrii Kuiukoff <andros.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19534
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
- SOC: MediaTek MT7981B
- RAM: 256MB DDR3
- FLASH: 128MB SPI-NAND WinBond W25N01GVZEIG
- NETWORK: 2x1Gb Lan 1x1Gb Wan
- WIFI: MediaTek MT7981B 2x2 DBDC 802.11ax 2T2R (2.4/5)
- LEDs: 3x WAN/LAN (green) 2x STATUS (red/blue)
- USB: 1x XHCI
Installation via Webinterface
-----------------------------
1. Rename OpenWrt sysupgrade bin to wavlink_wl-wn551X3-squashfs-sysupgrade.bin
The uppercase chars 551X3 are essential and checked by web interface.
2. Logon to webinterface
3. Go to network configuration -> mode selection
4. Choose mode "LAN bridge/access point"
5. Save configuration (maybe network reconfig needed)
6. Go to system upgrade
7. Choose local upgrade and provide renamed sysupgrade file
8. Start upgrade and wait for completion
9. Logon to OpenWrt (network config is preserved during upgrade)
Boot initramfs via TFTP & console
---------------------------------
1. Connect switch to network via LAN1 or LAN2
2. Power on switch
3. Press ESC until prompt reached "MT7981>"
4. Set own IP "setenv ipaddr 192.168.x.y"
5. Set TFTP IP "setenv serverip 192.168.a.b"
6. Set memory address "setenv loadaddr 0x46000000"
7. Download image "tftpboot openwrt-mediatek-filogic-wavlink_wl-wn551x3-initramfs.itb"
8. Boot image "bootm"
Notes
-----
- The red/blue LEDs give a background illumination to the top of the
case. The red LED is totally disabled to avoid noisy blinking.
- Aside from the design and the different LED colors & placements
the hardware and partitioning matches the WAVLINK WL-WN586X3 Rev B.
Therefor a common DTSI was prepared.
MAC Addresses (same as stock)
-----------------------------
LAN : 80:3F:5D:xx:xx:B1 (hw, 0x44e(text))
WAN : 80:3F:5D:xx:xx:B2 (hw, 0x460(text))
2.4GHz: 80:3F:5D:xx:xx:B1 (Factory, 0x4 (hex))
5GHz : driver auto generated
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19515
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
OpenFi 6C is a portable Wi-Fi 6 travel router based on MediaTek MT7981B+MT7976CN.
Two slightly different versions have been sold. The V1 board has a green color and lacks the modem LED. The V2 board is black and has a LED for the modem. The firmware should work on both of them.
Specifications:
- SoC: MediaTek MT7981B (Filogic 820) 1.3GHz dual-core ARM Cortex-A53
- RAM: 1GB DDR4
- Flash: 256MB SPI NAND
- Wireless: 2.4GHz/5GHz 802.11ax
- Ethernet: 1x 10/100/1000M LAN
- USB: 1x USB 3.0 Type-A port
- Expansion: M.2 slot for 5G modem
- Cooling: PWM-controlled fan
- Buttons: Reset, Mode switch
- LEDs: System, Ethernet, 5G WiFi, Modem status
**Installation via U-Boot web page**
1. Set static IP 192.168.21.2/255.255.255.0 on your computer.
2. Connect to the Ethernet port and hold the reset button while booting the device. Wait for 6-8 seconds, and release the reset button.
3. Open U-boot web page on your browser at http://192.168.21.1
4. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
5. Wait for automatic reboot.
**Installation via sysupgrade**
Flash the sysupgrade file via LuCI upgrade page without saving the settings.
Signed-off-by: Jiasheng Zhu <newbanyaya@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19512
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adds the capability to flash the factory image using the OEM recovery
software, ipTIME Firmware Wizard(11ac).
Installation
------------
1. Download the OEM recovery software from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router(keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router(LAN port) to the PC
6. Run the OEM recovery software and follow the instructions
7. Select the *squashfs-factory.bin file during the router recovery process
8. Wait for the router to boot from *squashfs-factory.bin
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19497
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This file should be generated automatically at runtime by the kernel
build system.
Link: https://github.com/openwrt/openwrt/pull/19473
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3GHz
- RAM : DDR3 256Mbytes, ESMT M15T2G16128A
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976CN dual-band Wi-Fi 6
- 2.4GHz : b/g/n/ax, MU-MIMO
- 5GHz : a/n/ac/ax, MU-MIMO
- Ethernet : MediaTek MT7531AE
- LAN : 10/100/1000 Mbps x4
- WAN : 10/100/1000 Mbps x1
- UART : 1x4 pin header on PCB
- [J6] TX, RX, GND, 3.3V (115200, 8N1)
- Buttons : WPS, Reset
- LEDs : 1x CPU (Amber)
1x Wi-Fi 5GHz (Amber)
1x Wi-Fi 2.4GHz (Amber)
1x WAN activity (Amber)
4x LAN activity (Amber)
- Power : 12VDC, 1A (Center positive polarity)
MAC address
-----------
+-----------+-------------------+-----------------------+
| Interface | MAC | Algorithm |
+-----------+-------------------+-----------------------+
| WLAN 2.4G | B0:38:6C:48:xx:xx | label |
| WLAN 5G | B2:38:6C:48:xx:xx | label with LA Bit Set |
| WAN | B0:38:6C:48:xx:xx | label + 1 |
| LAN | B0:38:6C:48:xx:xx | label + 3 |
+-----------+-------------------+-----------------------+
The WLAN 2.4G MAC was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router(keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router(LAN port) to the PC
6. Replace a file in the OEM recovery software with the file from step 2
7. Run the OEM recovery software and follow the instructions
8. Wait for the router to boot from *squashfs-factory.bin
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19368
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit increases the SPI bus frequency from 20 to 52 MHz. Reduces boot
time by 2s. Below is a performance comparison.
Before:
root@OpenWrt:~# dd if=/dev/mtd5 of=/dev/null bs=10M count=1 status=progress
10485760 bytes (10 MB, 10 MiB) copied, 2 s, 5.8 MB/
After:
root@OpenWrt:~# dd if=/dev/mtd5 of=/dev/null bs=10M count=1 status=progress
10485760 bytes (10 MB, 10 MiB) copied, 1 s, 9.7 MB/s
Taken from PR #18752 as each device should be tested individually, so I have
created a separate PR for this.
Signed-off-by: Sky Huang <SkyLake.Huang@mediatek.com>
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/19439
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With the switch to Linux 6.12 this driver was enabled by accident.
However, it doesn't support any of the router SoCs but is meant to be
used only by the smartphone, tablet and chromebook SoCs.
Disable the driver again to silence a kernel error logline during boot.
Fixes: 0a0f5f94ec ("mediatek: mt7623: update config-6.12")
Fixes: 029b7ed9c4 ("mediatek: mt7622: update config-6.12")
Reported-by: https://aparcar.org/openwrt-tests/119/
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
