Some mpc85xx boards still boot with failsafe configured on a non-LAN
interface. Align the preinit interface with the first DSA port or the
interface that LAN is connected to.
This makes failsafe reachable on devices where the default selection does
not map to the primary LAN port.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21516
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit a73db6d0a0)
Hardware specifications:
- CPU: Freescale/NXP P2020, dual-core PowerPC @ 1 GHz
- RAM: 1 GB DDR3
- Flash: 2 MB NOR, 512 MB NAND
- Networking: 7x Gigabit Ethernet ports (via two Marvell 88E6171
switches, each attached to a different MAC)
- USB: 2x USB 2.0 ports (front panel)
- mini-PCIe slot
- RTC: Ricoh RS5C372A
- 4 buttons (via external MCU)
- 3 LEDs (via external MCU)
- LCD display (via external MCU)
Installation procedure:
1. Obtain the original MAC address table from the stock bootlog, for
example:
setting device eth0 to 00:90:7f:00:00:01
setting device eth1 to 00:90:7f:00:00:02
setting device eth2 to 00:90:7f:00:00:03
setting device eth3 to 00:90:7f:00:00:04
setting device eth4 to 00:90:7f:00:00:05
setting device eth5 to 00:90:7f:00:00:06
setting device eth6 to 00:90:7f:00:00:07
2. Open the case and move jumper JP1 from 2-3 to 1-2 to enter FAILSAFE
mode.
3. Power on the device and interrupt the boot process to access the U-Boot
shell.
4. Program the MAC base address into the EEPROM (text after '#' is a
comment):
mac ports 3
mac 2 00:90:7f:00:00:01 # first MAC address from bootlog
mac save
5. Reset the device and enter the U-Boot console again.
6. Connect a TFTP server to port 6 and boot the initramfs image:
setenv ipaddr 192.168.1.3
setenv serverip 192.168.1.2
setenv loadaddr 1000000
tftpboot $loadaddr openwrt-mpc85xx-p2020-watchguard_xtm330-initramfs-kernel.bin
bootm $loadaddr
7. (Optional) Backup all MTD partitions if you want the ability to restore
stock firmware.
8. Perform a normal sysupgrade from the initramfs environment.
9. Power off the device and move jumper JP1 back to 2-3.
10. The device will now boot OpenWrt.
Known issues:
- LCD, buttons and LEDs are controlled by an external MCU; the protocol is
currently unknown.
- The internal connection between the two Marvell switches is unused by
OpenWrt.
- The stock firmware uses an empty U-Boot environment; saving variables
modifies the environment and prevents a normal boot. FAILSAFE U-Boot
remains functional.
- WatchGuard configuration is encrypted; DSA MAC addresses are stored in
this configuration.
- Failsafe Ethernet works on port1.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21020
(cherry picked from commit 6150f9ceab)
Link: https://github.com/openwrt/openwrt/pull/21517
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for the Watchguard Firebox models
T10-W, T15 and T15-W.
CPU: Freescale P1010
RAM: 512MB (T10) / 1024MB (T15)
Flash: 1MB SPI-NOR, 512MB NAND (T10) / 1024MB NAND (T15)
WiFi: 802.11abgn 2T2R AR9582 based Mini-PCIe card (-W models only)
Ethernet: 3x GBE (via AR8033 PHY)
LEDs: 7x hard-wired (6x LAN, 1x Power)
4x GPIO single-colored (Attn/Status/Mode/Failover)
1x GPIO dual-colored (2.4/5G WiFi, -W models only)
Serial: RJ45, Cisco pinout, 115200/8N1
Other: Battery backed RTC
Atmel TPM 1.2 chip (unsupported)
Based on 35f6d79, which introduced Watchguard Firebox T10 support.
The T10 and T15 are identical hardware, with the exception of the T15
having twice the flash and RAM size.
The T10-W and T15-W models have their Mini-PCIe slot populated with an ath9
(AR9582) based WiFi card. The slot is either unpopulated or empty for
non-WiFi models. All required drivers are present by default on the mpc85xx
target, so T10/T10-W resp. T15/T15-W can use the same OpenWrt image.
This commit also introduces the zImage loader from 7d768a9 to boot the
kernel. This is required, since the U-Boot version used in these devices
appears to have a hard limit of 16MB for the kernel size it can handle. The
current kernel size is around 17MB, though, due to kernel page alignment
required for memory protection.
Installation (replaces previous instructions for T10):
1. If the U-Boot password is known, proceed with step 2.
If the U-Boot password is unknown, dump the NOR flash using a SPI
programmer and patch the unknown password to a known one. You can use
blocktrron's Python script:
https://github.com/blocktrron/t10-uboot-patcher/
This script will patch the password to '1234' (without quotes).
Alternatively, you can search for the hashed password in the NOR dump
yourself and overwrite it with a known one. The SHA1 hash is:
E597301A1D89FF3F6D318DBF4DBA0A5ABC5ECBEA
Write the patched NOR dump back to the device.
2. Connect the device via serial cable, power it on and interrupt
the boot process by pressing Ctrl+C. Enter the U-Boot password to access
the CLI.
3. (Optional) Populate the uboot-env partition by entering:
saveenv
This will allow you to use uboot-envtools from within OpenWrt later,
e.g. to increase the loadable kernel size.
The default loadable kernel size is 5MB, the compressed kernel size at
the time of this commit is 3.1MB.
4. Serve the initramfs OpenWrt image from a TFTP server at 10.0.1.13/24,
connected to eth0 (WAN) of the device. File name must be 'uImage'. Boot
with:
tftpboot; bootm;
Make sure to use the correct image for your device (T10 resp. T15)!
5. After booting, connect to OpenWrt on eth1 (LAN) via SSH. Verify
that the UBI partiton is mtd7, format it and install the sysupgrade
image.
$ cat /proc/mtd
$ ubiformat /dev/mtd7 -y
$ sysupgrade -n <path to sysupgrade.bin>
6. The device should now boot OpenWrt from NAND flash. Enjoy.
Back to stock:
Use the vendor recovery procedure.
Stock recovery might also be necessary in case you have accidentally used
the fw_setenv command from within OpenWrt without using saveenv in U-Boot
first.
In order to use the vendor firmware recovery procedure, the NAND partitions
mtd3 to mtd6 must remain intact. Make sure not to overwrite them, or keep
dumps of them for later recovery.
Signed-off-by: Shine <4c.fce2@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16776
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit be7aa5bda4)
In preparation of adding support for additional Watchguard Firebox devices
based on Freescale P1010, introduce a common DTSI.
Signed-off-by: Shine <4c.fce2@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16776
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 15ef024805)
This partially reverts 78d259e7d2.
That commit broke mounting the root fs on Sophos RED 15w due to
partition size mismatch, and changed the partition sequence, causing
the OpenWrt partition numbers to change from mtd3:kernel/mtd4:ubi to
mtd4:kernel/mtd5:ubi.
Fixes: 78d259e7d2 ("mpc85xx: fix some dtc warnings")
Signed-off-by: Shine <4c.fce2@proton.me>
Link: https://github.com/openwrt/openwrt/pull/20745
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Define MSM466 as alternative name, to explicitly show the device is
supported using existing image (MSM460). The only difference between
the MSM460 and MSM466 is that the MSM466 has external antenna.
Signed-off-by: Raylynn Knight <rayknight@me.com>
Link: https://github.com/openwrt/openwrt/pull/20937
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The initramfs images beginning 24.10 do not boot on the AP3825i. The
space available for decompression preceeding the compressed image is not
enough, crashing the system.
To make existing installation instructions continue to work, link the
loader at an address following the loadaddress of the U-Boot image.
Signed-off-by: David Bauer <mail@david-bauer.net>
Usage of strlcpy results in a compilation error. strscpy is preferred
anyways and equivalent for our case.
Signed-off-by: David Bauer <mail@david-bauer.net>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
CONFIG_MTD_CFI was disabled in p1010 subtarget.
It causes problem with Aerohive BR200-WP router.
This patch enables CONFIG_MTD_CFI in p1010 config-default file.
Fixes: e9dd6da916 ("mpc85xx: p1010: add missing symbols")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20419
Signed-off-by: Nick Hainke <vincent@systemli.org>
In the conversion to dts, qca,led-pin was used for both interfaces.
Unfortunately, it's mutually exclusive with gpio-controller which made
it not do anything.
Fixes: 949e1a0 ("mpc85xx: tl-wdr4900: move platform code to dts")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19758
Signed-off-by: Robert Marko <robimarko@gmail.com>
Define MSM430 as alternative name, to explicitly show the device is
supported using existing image (MSM460).
I can confirm that the guide from
https://github.com/blocktrron/msm460-flashing works perfectly fine with
the HP MSM430 as well.
In fact, the MSM430 running the original firmware operates as
a 2x3:2 access point, but after flashing it with OpenWRT, it functions
as a 3x3:3 access point — just like the MSM460 model.
It seems that the MSM430 is essentially the same hardware as the MSM460,
with limitations imposed by the original (HP) software.
Signed-off-by: Jan Taczanowski <jan.taczanowski@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19540
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Comes with kernel 6.16. I assume it will be backported at some point.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19329
Signed-off-by: Robert Marko <robimarko@gmail.com>
The function name is misspelled and does not exist. Fix the function
name so the correct function is called.
Signed-off-by: David Bauer <mail@david-bauer.net>
Upstream seems to be using led-sources instead of custom properties.
Code mostly taken from mt76.
Changed all(few) users of qca,led_pin to use the new format.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18805
Signed-off-by: Robert Marko <robimarko@gmail.com>
The "gpio-export" driver doesn't require a "reg" property in the
device tree, hence we don't need to use the "#size-cells" property
to describe the size of "reg".
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18290
Signed-off-by: Robert Marko <robimarko@gmail.com>
The CONFIG_NET_SWITCHDEV option is needed by CONFIG_DSA and some other
options. It is boolean, we have to compile it into the kernel it self.
Activate it for all targets in the generic configuration, it is already
activated for most of them. This allows to install DSA drivers as a
module.
On the ramips/mt7620 target the kernel would grown by 4.5kB.
For some small targets which do not support a DSA switch by default the
option is deactivated.
Link: https://github.com/openwrt/openwrt/pull/17668
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>
Adjusts the default config to modern kernels.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>
These get dynamically set based on compiler version. Not relevant for
targets.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16770
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This symbol is no longer present.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16770
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It's shared by all targets. Unlike the other shared symbols, it's not
removed by kernel_oldconfig.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16756
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
MAC-addresses are stored with colons, thus they can now be referenced
using NVMEM.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16310
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream commit 9ba0cae3cac07c21c583f9ff194f74043f90d29c made FSL_IFC
visible and selectable, which means that in order for MTD_NAND_FSL_IFC
to work, it needs these two extra CONFIG options.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16717
Signed-off-by: Robert Marko <robimarko@gmail.com>
No reason for them not to be so. Matches various upstream commits for
PPC.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16345
Signed-off-by: Robert Marko <robimarko@gmail.com>
With upstream commit 0aafbdf35c75cbfec82636d01e6dc7950bc1507c , this is
now default. No need to override.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16345
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream commit does this for simple cases, which all of these are.
Commit: 1c96fcdef8c7492ecf34ed70102a1ae5253ef9d1
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16345
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit introduces led nodes in tl-wdr4900-v1 dts.
It allows to configure switch leds from userspace.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16226
Signed-off-by: Robert Marko <robimarko@gmail.com>
TP-Link tl-wdr4900-v1 has two usb leds. Modern kernels can handle usb
led trigger. Let's enable it.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16226
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit change led description in dts file from old method to new
approach accepted by upstream.
USB power gpio is handled by gpio-export now.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16226
Signed-off-by: Robert Marko <robimarko@gmail.com>
No benefit in doing so in platform file. Code for dts has already been
written. Might as well use it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16125
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated. No need for any of this.
Calibration size was adjusted to 440, which is the standard value for
ath9k radios.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16125
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that the ports are defined in DTS, this is trivial to do.
Avoids userspace handling.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16125
Signed-off-by: Robert Marko <robimarko@gmail.com>
