With further investigation it was found a race in generating .itb images
that include a RootFS caused by the mkits.sh and the mkimage.
Due to the fact that mkits.sh generates a .pagesync image of the passed
rootfs, it can happen that, concurrently, mkimage can be called at the
same time mkits.sh is creating another .pagesync for the same rootfs.
This cause mkimage to use an half made rootfs.pagesync creating a
corrupted image.
To address this, also protect the mkimage with the same lock used for
mkits.sh preventing any kind of concurrent usage/generation of the
rootfs.pagesync blob
Fixes: 52cc9d82f1 ("kernel: rework Initramfs locking logic")
Link: https://github.com/openwrt/openwrt/pull/20492
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add pending patch that disable libmagic support as this cause
reproducibility issue due to timing of presence of libmagic library at
times e2fsprogs gets compiled.
The new patch adds control on libmagic inclusion and we add the
--without-libmagic to the configure args by default.
Reported-by: Paul Spooren <mail@aparcar.org>
Link: https://github.com/openwrt/openwrt/pull/20499
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant patch for host build as this has been fixed in 1.44.1
but for some reason it wasn't notice with the patch directly refreshed
(with the fix right up)
Fixes: 198172c048 ("package/utils/e2fsprogs: update to 1.44.1")
Link: https://github.com/openwrt/openwrt/pull/20499
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport additional patch required for NPU support of Airoha AN7583.
These are specific for the NPU module with some minor fixes and to adds
upport for loading the specific Airoha AN7583 NPU firmware.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add relevant nodes for NPU support for Airoha AN7583 and enable the
kernel config to enable support in the Airoha Ethernet driver.
NPU firmware is scheduled to be upstreamed to linux-firmware and will be
added once present upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix the current image Makefile for Airoha AN7583 by dropping the
artifacts entry for bootloader and add default PKG for the PHY mounted
on the RFB boards.
The artifacts for the bootloader will be readded later once ATF-A
support will be pushed mainline.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
While adding support for Airoha AN7583, it was forget to push the EMMC
DTS while defining the variant in the image Makefile.
Add the missing DTS to fix image creation error.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
On the Airoha AN7583 EVB there are 2 Aeonsemi AS21xxx PHY but only the
one connected to Serdes Ethernet is usable as the other connected to
Serdes PON is not actually HW connected (as the serdes is connected to
the BOSA port)
Add comments and disable the relevant PHY.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This commit changes the Meraki MR33 and MR74 device trees to use nvmem
for ART calibration.
The WiFi BDF was moved from insect-common.dtsi to the respective
device files in preparation for additional insect-family devices being added.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20474
Signed-off-by: Robert Marko <robimarko@gmail.com>
0d0fac30075f dhcpv4: bump problem scenario up to warn
bf6137092346 config: properly set log level from uci
7956f4271b4e dhcpv6: RFC4833 timezones
7000557cd8f6 dhcpv6-ia: respect prefix assigned to interface (>= /64)
e1e60601ffeb odhcpd: improve odhcpd_urandom()
c2eb4b59f107 config: fix erroneous clamp message if clamp value == max
54b9e729b00d dhcpv4: bail earlier on release/decline
417f4b11d352 dhcpv4: don't hardcode options array length
d63fa3c3612c dhcpv4: shrink struct dhcpv4_message
9653b43617e3 dhcpv4: use iovec for forcereconf messages, fix hash
bf41f4edfbe3 dhcpv4: fix padding of iovec message in dhcpv4_handle_msg()
be68f423c528 dhcpv4: some minor cleanups post-iovec
e24a371ef714 dhcpv4: use iovec for forcerenew opts
bd353e891ae6 dhcpv4: use iovec for router and DNS server
b81cfaa7859e dhcpv4: use iovec for DNS search and MTU
578a9289440b dhcpv4: use iovec for netmask/hostname/broadcast
5bafc17b79d8 dhcpv4: use iovec for leasetime/renew/rebind
b63448ffe447 dhcpv4: introduce a reply_opts array
0533eaea0a94 dhcpv4: use iovec for DNR
6329e37d595d dhcpv4: use iovec for NTP
87fee619205d dhcpv4: use iovec for message and serverid
2f97bf0b56de dhcpv4: reorder some more variables in dhcpv4_handle_msg()
18c1b02bdc20 dhcpv4: remove one more variable from dhcpv4_handle_msg()
6fd691ff29cd dhcpv4: move dest handling from dhcpv4_handle_msg()
1f803caf9a1f dhcpv4: don't copy reqopts around
b1be3984ebf8 dhcpv4: more refactoring of dhcpv4_handle_msg()
85717bedf8ce dhcpv4: clarify variable names in dhcpv4_handle_msg()
be864ccf9919 dhcpv4: some more cleanups to dhcpv4_handle_msg()
f87464520564 dhcpv4: preparations for iovec usage
f48e1c205af3 odhcdp: use a more suitable clock
7e78caac4eae dhcpv6: change dhcpv6 message type check in relay
288abd9c4046 dhcpv6: move dhcpv6 message type check for early exit
d504458ef515 odhcpd: add a simple build script
4ee309a54011 github: improve CI
ff3a241ccc98 odhcpd: shrink binary size by creating a logging function
e2ecf7ba6d72 odhcpd: support stderr logging
5de3b0d5b509 odhcpd: add log helpers
398d03a1a236 config: cap dhcpv6_pd_min_len to max instead of only logging error
4f54738d3ae7 config: clamp dhcpv6_hostid_len instead of only logging an error
465f19c9c2e3 config: clamp ra_mtu into 1280-65535 range
434b06133997 config: cap ra_retranstime and warn instead of only logging an error
e5f58a90a147 config: cap ra_hoplimit to maximum and warn instead of logging an error
208eb10307c1 config: cap ra_reachabletime to RFC maximum instead of logging error
93449f1513b4 config: drop double size lease times; they are all UINT32_MAX;
439c0ceab131 router: redefine ra_mininterval and ra_maxinterval as uint32_t
84b4dfe81363 config: clamp ra_mininterval, ra_maxinterval, ra_lifetime at load time
aa4f26232e05 router: refactor calc_ra_lifetime; redefine ra_lifetime as uint32_t
6ece28ffd475 config: do MaxRtrAdvInterval init at (ra_maxinterval) init time
dc03e02d973e router: Apply updated values from RFC9096 (updates RFC4861) to RA/ND
cc7766c12abe router: Apply updated values from RFC8319 (updates RFC4861) to RA/ND
964da13e758c config: refactor parse_leasetime() - branch amount remains same
9646c749467b github: fix CMAKE_SYSTEM_PROCESSOR copy&paste
288206c9a2ed github: add CI build
30780debd691 odhcpd: fix a compilation error
e0b2c3cf9476 odhcpd: allow assignments to be reassigned
01e5e311b0db odhcpd: support multiple per-client DUIDs
aebc647a6b7b odhcpd: support assignments on the basis of IAID
cc3ec9c20c61 odhcpd: support IAIDs for static DHCPv6 leases
e42c62725942 odhcpd: break up complex matching logic
e1123906a4bc odhcpd: document the ubus interface
c69200195263 dhcpv4: generate dbus events on lease expiry
dd7a2d474d0d dhcpv4: fix ubus events
22481d848e0d odhcpd: remove mac_len argument to ubus_bcast_dhcp_event()
d31d64efd56c odhcpd: fix ubus support flag in help msg
9bc1b4e26e10 odhcpd: reduce use of WITH_UBUS defines in code
d402cdae4316 ndp: fix macOS IPv6 compatibility by using link-local source addresses
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
77e1ae21e67f odhcp6c: set server address from Information-request reply
e24ac1cf8c27 dhcpv6: use a per-interface IAID for IA_NA requests
053e6c4b3863 github: improve CI
b65ff293a969 dhcpv6: Check status code for IA_ADDR operations
3c7e425169e1 dhcpv6: Add error checking to handle renew failure for IA_PD operations
8de25373a860 dhcpv6: dhcpv6_parse_ia refactor to switch case
ca3cd525f447 odhcp6c: fix deamon raw buffer inc
d7afeea2b965 dhcpv6c: fix illegal DHCPV6_OPT_FQDN
70f7467db301 script: don't ignore RA with zero router lifetime
6ca1552cb3fe odhcp6c: sync and accumulate RA & DHCPv6 events as fast as possible
29b58cfb4711 odhcp6c: update cmake file
ee6d4a82bbeb github: add CI build
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Userspace handling is deprecated.
Use ath9k LED instead of specifying a generic one.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16286
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Userspace handling is deprecated.
Use ath9k LED binding to avoid generic LED usage.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16286
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This board is also as known as E-Life ETR631-T/ETR635-U.
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Uncompress the configuration:
* Enter fakeroot if you are not login as root.
tar -zxf <filename>.tar.gz
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; telnetd; ) &
5. Repack the configuration:
tar -zcf backup.tar.gz etc/
6. Upload new configuration via web interface, now you can connect to
KOMI A31 via telnet.
Flash instructions:
1. Connect to KOMI A31, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-konka_komi-a31-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-konka_komi-a31-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20357
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Allows us a bit more headroom flash wise and access to more recent
compression algorithms.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Link: https://github.com/openwrt/openwrt/pull/20445
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Drop config and patches for Linux 6.6.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/20468
Signed-off-by: Nick Hainke <vincent@systemli.org>
Switch to Linux kernel 6.12.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/20468
Signed-off-by: Nick Hainke <vincent@systemli.org>
Backport upstream patch for AN7583 Ethernet support. While at it also
backport some additional fixes required to apply the AN7583 patches
cleanly.
Refresh all affected patch automatically (aside from the XSI patch that
changed the implementation)
Link: https://github.com/openwrt/openwrt/pull/20489
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport phylink patches for PCS/PHY caps OPs. This makes it easier to
align future generic PCS patch and permit supporting special PHY that
needs specific tune if "in-band" mode is enabled (for example Aeonsemi
PHYs)
This is also mainly using the upstream version of the Mediatek patch
739-net-add-negotiation-of-in-band-capabilities.
All affected patch automatically refreshed.
Link: https://github.com/openwrt/openwrt/pull/20461
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Now that we have a board file, add calibration variant for TP-Link
Archer C60 v2 and add ipq-wifi package for it.
Tested-by: Semih Baskan <strstgs@gmail.com>
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20496
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add IPQ Wifi entry for ath79 TP-Link Archer C60 v2.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20496
Signed-off-by: Robert Marko <robimarko@gmail.com>
L3 Offloading caused DHCP packets to be dropped at hardware level
And potentially buggy route implementation can cause a crash
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Co-developed-by: Sven Eckelmann <se@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20208
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RTL931x is not supporting L3 offloading at the moment. To avoid crashes
when using this switch, simply disable L3 offloading completely.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Co-developed-by: Sven Eckelmann <se@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20208
Signed-off-by: Robert Marko <robimarko@gmail.com>
Whenever the first bss is removed, any pending scan still keeps a reference
to it. Cancel it in order to prevent use-after-free bugs.
Reported-by: Chad Monroe <chad.monroe@adtran.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
df2f5c9a30f8 veth: delete device before creation to handle stale state
b6d371f30770 system-linux: handle RTM_DELLINK events for device state tracking
777f5942fa7d system-linux: only parse device status for AF_UNSPEC link messages
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rework the package SOURCE entry handling to account for the --root feeds
script feature.
Move the SOURCE entry string manipulation logic outside package-defaults.mk
in package.mk and limit only to non DUMP scenario to not pollute the .mk
too much.
Restructure the previous logic and add a new additional condition.
If we detect the package comes from a feed, replace any feed path that
have the _root prefix to the feed name with the non-root variant (the
feeds script create a symbolic link to it) and point the package SOURCE
entry to what the symbolic link points to.
Example:
Feed link: feeds/base_root/package -> feeds/base
Package: feeds/base_root/package/system/uci -> feeds/base/system/uci
Link: https://github.com/openwrt/openwrt/pull/20459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
a33d59f7af (2025-10-14) restored dts files for kernel 6.6 to files-6.6
after the preceding 15fa59c41f moved files-6.6 to files-6.12 to be
used by the new testing kernel, 6.12. This restoration omitted
1a3f05eb2b (2025-10-08), which fixed important aspects of the wifi
device definitions in qcom-ipq8064-eax500.dtsi and
qcom-ipq8064-unifi-ac-hd.dts.
The 1a3f05eb2b fix persisted into the 6.12 dts files. This change now
restores it for 6.6. Note that ipq806x is currently using kernel 6.6 for
most purposes, as 6.12 is only in testing status for this target.
This change was prepared with `git diff
a33d59f7af8f:target/linux/ipq806x/files-6.6
15fa59c41f0d^:target/linux/ipq806x/files-6.6`. This identified
c186d17fa5 (2025-10-08) as another change that was not present in the
restored files-6.6, but it has since been superseded by 2a709d108e
(2025-10-20), so no action is necessary to restore it. There were no
diffs present between these revisions in config-6.6 or patches-6.6,
which were also moved and restored in the 6.12 bring-up.
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Cc: Shiji Yang <yangshiji66@outlook.com>
Cc: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20464
Signed-off-by: Robert Marko <robimarko@gmail.com>
SQUASHFS_DECOMP_MULTI_PERCPU is selected by
SQUASHFS_COMPILE_DECOMP_MULTI_PERCPU, so add it.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20140
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The pinctrl driver should be enabled based on the SoC supported
by the subtarget, rather than enabling all by default.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20140
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the common kernel config found when 'make kernel_oldconfig'.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20140
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove earlyprintk from bootargs for arm64 boards.
This option is only valid for arm:
```
Unknown kernel command line parameters "earlyprintk",
will be passed to user space.
```
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20140
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The cortexa53 target currently uses cpu erratums for Cortex-A510,
Cortex-A710, and Neoverse-N2. Remove them and enable cpu erratums
for Cortex-A53.
Fixes: f01982e ("sunxi: add testing kernel 6.1")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20140
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
