It's not the proper one. No of_platform_ APIs are being used.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21164
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
follow-up to 148207730a
Schoolboy error on the peer_psk value.
Also fix an issue when joining peer IPv4 and IPv6 AllowedIPs
(${peer_a_ips/ /, } replaces only the first space, while
${peer_a_ips// /, } replaces all the spaces).
Closes: https://github.com/openwrt/openwrt/issues/21847
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21851
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a status method to both hostapd and wpa_supplicant ubus objects
that lists all configured interfaces with their wiphy, MAC address,
and running/pending state. For MLO interfaces, links are grouped
under a single entry with per-link status.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- preserve (active) interface (at reload)
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21784
Signed-off-by: Robert Marko <robimarko@gmail.com>
- no longer write any temporary file for peer gen
- use wg syncconf to update active interfaces (not setconf)
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21784
Signed-off-by: Robert Marko <robimarko@gmail.com>
- no longer write any temporary file for key gen
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21784
Signed-off-by: Robert Marko <robimarko@gmail.com>
Proto handler now also detects changes to
- addresses
Tighten also assign address portion
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21784
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit 168d5af added the possibility to configure netifd logging level.
The option is read from /etc/config/network and validated.
Supposedly the validation sets 2 as default.
But in case of a syntax error in /etc/config/network, the validation
result can be empty. Then the always passed option to netifd is
just '-l' instead of '-l 2'. That crashes netifd and prevents network
from launching.
Add a fallback value to the variable, so that there will always be
a proper value after the '-l' option.
Improves: 168d5af "netifd: add loglevel config option (fixes#18001)"
Fixes: #21816
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/21819
Signed-off-by: Robert Marko <robimarko@gmail.com>
Removing tmp/ after having built base-files or toolchain currently
breaks rootfs generation:
$ rm -rf tmp
$ make V=w
...
make[2] package/install
cat: .../openwrt/tmp/base-files.version: No such file or directory
cat: .../openwrt/openwrt/tmp/libc.version: No such file or directory
ERROR: 'base-files=' is not a valid world dependency, format is name(@tag)([<>~=]version)
make[2]: *** [package/Makefile💯 package/install] Error 99
The only way to recover from here is to clean toolchain and base-files via
$ make package/{base-files,toolchain}/clean
tmp is supposed to be ephemeral, so clearing it is an expected action,
which normally just triggers a regeneration of all files there.
Fix this by moving the version files to $(STAGING_DIR).
Fixes: 63e178f067 ("build: lock versions for special APK packages")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21803
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ucode wifi-scripts unconditionally set ieee80211w=1 for psk-sae
and eap-eap2 auth types, ignoring any user-configured value. This
caused ieee80211w=2 (MFP required) to be silently downgraded to 1
(MFP optional) when using sae-mixed encryption.
Change the logic to only set the default of 1 when ieee80211w is not
already configured by the user.
Fixes: https://github.com/openwrt/openwrt/issues/21751
Signed-off-by: Felix Fietkau <nbd@nbd.name>
b3ee1209a3d0 uclient-http: reset fd to -1 after close in disconnect
9c2ad269c42b uclient-http: fix seq field check to use correct field
80c9bd29c233 uclient-http: fix hang on HTTP to HTTPS redirect
931bbfeb2c92 ucode: fix memory leak when using ssl context
Fixes: https://github.com/openwrt/uclient/issues/11
Fixes: https://github.com/openwrt/uclient/issues/13
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add a module for tpm-tis-spi for TCG TIS 1.3 TPM security chips
connected to a regular non-tcg SPI master.
Add imx target compatibility for kmod-tpm.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/21726
Signed-off-by: Robert Marko <robimarko@gmail.com>
Adding base64 encoded beacon data needs the base64 functions to be available
Fixes: b44d4290fe ("hostapd: add raw beacon report data to ubus notification")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add IPQ Wifi entry for ath79 TP-Link TL-WA1201 v2.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21736
Signed-off-by: Robert Marko <robimarko@gmail.com>
The mobility_domain value generated by ucode differed from the previous
shell script implementation. The legacy shell script used `echo` on the
SSID, which appended a trailing newline.
To maintain roaming compatibility with pre-25.12 releases and OpenWrt
forks in default configuration, update the ucode logic to include this
newline character when generating the default value.
Fixes: #21731
Signed-off-by: Youfu Zhang <zhangyoufu@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21732
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ensure md volumes are ready before attempting to mount volumes.
Signed-off-by: Joe Hohertz <jhohertz@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21553
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Extend the taxonomy subsystem to capture the complete association frame
in addition to the existing probe and association IE data.
This adds a new assoc_frame_taxonomy field to struct sta_info and exposes
it via the get_sta_ies ubus method as a base64-encoded "assoc_frame" field.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Extend the hostapd_rrm_beacon_req ubus method to support the optional
reporting_detail parameter as defined in IEEE 802.11-2016 section 9.4.2.21.7.
Also fix missing assignment operators (=) in the beacon_req_policy array
initialisation.
Signed-off-by: John Crispin <john@phrozen.org>
Add netifd_loglevel to /etc/config/network:
config globals 'globals'
option netifd_loglevel '1'
The netifd's default value is 2.
Signed-off-by: Peter Meiser <peter.meiser@gmx.com>
Link: https://github.com/openwrt/openwrt/pull/19737
Signed-off-by: Robert Marko <robimarko@gmail.com>
TCL LINKHUB HH500V also known as Vodafone Gigacube B157 is a dual band
802.11ax 5G NR CPE with an FXS port.
Specifications:
* SoC: Qualcomm IPQ8072A
* RAM: 1024 MB
* NAND flash: 256MB NAND (MT29F2G08ABBGAH4)
* NOR flash: 64MB NOR (MX25U25635F) - only in some variants
* WiFi 5G: Qualcomm QCN5054
* WiFi 2.4G: Qualcomm QCN5024
* Ethernet 2.5G: Qualcomm QCA8081
* Ethernet 1G: Qualcomm QCA8075
* Modem: GosunCn GM800 (Qualcomm Snapdragon X55)
* SIM: 1 nano-SIM card slot
* Buttons: Power, Reset, WPS
* LEDs: Power (B/R), WiFi (B), 4G (B/Y/R), 5G (B/Y/R)
* VoIP: 1 FXS RJ11 port (not supported in OpenWrt)
* Power: 12V, 3A
UART serial console:
* 115200,8N1,1.8V
* Three unmarked test points next to QJ2012A:
+---------+
| QJ2012A |
+---------+
o TX
o GND
o RX
o
o
o
Installation via OEM firmware:
* Use the following process to obtain root ssh access
https://forum.openwrt.org/t/150371/24
* Connect using root with no password on port 42000
* Optionally for serial bootloader access run :
fw_setenv bootdelay=3
* SCP factory.bin to /tmp
* Run:
sysupgrade -n /tmp/factory.bin
Installation via serial console and OEM firmware::
* Use console to access OEM firmware shell
* Proceed with SCP & sysupgrade as described above
Other notes:
* This device uses active partition rotation
* Some versions (TCL branded?) have a NOR chip in addition to NAND
* The above is supported by u-boot patching DT partitions
* DT patching does NOT occur on tftpboot/bootm
* Modem is detected as foxconn-sdx55 by kernel (same VID/PID)
* This works OK-ish and should be improved if we can get OEM modem details
Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switchdev driver used by microchipsw supports DCB and has not storage
constraints, so enable kernel and driver DCB support by default.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Specifications:
* SoC: Qualcomm IPQ6018/AP-CP03-C1 (64-bit Quad-core Arm Cortex-A53 @ 1.2 GHz)
* RAM: 2x Zentel A3T4GF40BBF-HP (1 GiB DDR3-1866 (13-13-13))
* Serial Port: 1v8 TTL 115200n8
* Wi-Fi: Qualcomm QCN5022 (802.11ax/b/g/n)
* Wi-Fi: Qualcomm QCN5052 (802.11ac/ax/n)
* Ethernet: RTL8211FS (10/100/1000BASE-T)
* Flash: GigaDevice PSR1GA30DT (128 MiB)
* LEDs: 1x Blue Status (GPIO 35 Active High)
* Buttons: 1x Reset (GPIO 9 Active Low)
* FCCID: 2AXJ4EAP620HDV3
* UART: 4-pin unpopulated header by the J1 footprint
Installation Instructions (Serial+TFTP):
1. Locate the J1 footprint which contains 4 unpopulated pins
where starting from the arrow, the pins are TX, RX, VCC and GND
respectively.
2. Connect a 1v8 TTL port to the 4 pins. Ensure RX and TX are crossed
over.
3. Copy openwrt-qualcommax-ipq60xx-tplink_eap620-hd-v3-initramfs-uImage.itb
to your TFTP server.
4. Power up the AP and hold Ctrl+B in the serial console (115200n8) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
IPQ6018# setenv serverip <TFTP server addr>
IPQ6018# setenv ipaddr <addr of the AP>
IPQ6018# tftpboot 0x44000000 openwrt-qualcommax-ipq60xx-tplink_eap620-hd-v3-initramfs-uImage.itb
IPQ6018# bootm 0x44000000
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp -O openwrt-qualcommax-ipq60xx-tplink_eap620-hd-v3-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq60xx-tplink_eap620-hd-v3-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Installation Instructions (Web UI method):
1. Set up the device using the vendor's web UI. Navigate to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
2. Connect to the machine via SSH:
$ ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
3. Disable signature verification:
$ cliclientd stopcs
4. Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
5. Go to System -> Firmware Update.
Under "New Firmware File", click "Browse" and select the image.
Select "Update" and confirm by clicking "OK".
6. If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWrt.
Device support followed from EAP620HD v2 and eap6xx-outdoor for DTS.
Links: openwrt/openwrt#18227
Signed-off-by: John Christoforidis <github@yanny.dev>
Link: https://github.com/openwrt/openwrt/pull/21467
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update the econet-eth driver to a new version which is of
sufficient quality that it is realistic to think about upstreaming.
This version is now NAPI based, collects stats, downloads without
dropped packets anymore, has debugfs introspection, and can be
unloaded and reloaded (providing the reset controller is present).
PR #21545 is recommended but not required, without this the
ethernet driver will log a warning on startup because it can't get
the resets and it will be impossible to unload and reload the
driver without a reboot. However, the PoC driver was not capable of
reloading so this is not a regression.
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://github.com/openwrt/openwrt/pull/21557
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch was manually edited but not refreshed.
Fixes: 794b4dee65 ("uboot-mediatek: add 8g check to bpi-r4 environment for bl2")
Fixes: 46ee5209aa ("uboot-mediatek: add command for getting size of ram")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21693
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
